Morphology and properties of biodegradable poly (lactic acid)/poly (butylene adipate-co-terephthalate) blends with different viscosity ratio

Phase morphology exerts a tremendous influence on the properties of polymer blends. The development of the blend morphology depends not only on the intrinsic structure of the component polymers but also on extrinsic factors such as viscosity ratio, shearing force and temperature in the melt processing. In this study, various poly (butylene adipate-co-terephthalate) (PBAT) materials with different melt viscosity were prepared, and then poly (lactic acid) (PLA)/PBAT blends with different viscosity ratio were prepared in a counter-rotating twin-screw extruder under constant processing conditions. The influence of viscosity ratio on the morphology, mechanical, thermal and rheological properties of PLA/PBAT (70/30 w/w) blends was investigated. The experimental results showed that the morphology and properties of PLA/PBAT blends strongly depended on the viscosity ratio. Finer size PBAT phase were observed for viscosity ratio less than 1 (λ < 1) compared to samples with λ > 1. It was found that the interfacial tensions of PLA and PBAT were significantly different when the viscosity ratio was changed, the lowest interfacial tensions (0.12 mN/m) was obtained when the viscosity was 0.77. Additionally, the maximal tensile strength in PLA/PBAT blends were obtained when the viscosity ratio was 0.44, while the maximal impact properties were obtained when the viscosity ratio was 1.95.     

Melt processing of maleic anhydride grafted poly(lactic acid) and its compatibilizing effect on poly(lactic acid)/poly(butylene adipate-<Emphasis Type="Italic">co</Emphasis>-terephthalate) blend and their composite

Poly(lactic acid) (PLA)/poly(butylene adipate-co-terephthalate) (PBAT) blends were prepared using melt processing. The effects of maleic anhydride grafted PLA (PLA-g-MA) and calcium carbonate (CaCO₃) content on mechanical, thermal, and morphological properties of the blends were investigated. PLA-g-MA was synthesized by varying monomer and initiator contents using a reactive melt-grafting process. Tensile properties of PLA/PBAT blend were enhanced with adding 2 phr of PLA-g-MA. SEM micrographs exhibited the improvement of interfacial adhesion between PLA and PBAT in the compatibilized blend. Moreover, thermal stability of the blends improved with presence of PLA-g-MA. With increasing CaCO₃ content, Young’s modulus of the composites increased.     

Thermal degradation of poly(lactic acid) (PLA) and poly(butylene adipate-co-terephthalate) (PBAT) and their blends upon melt processing

Poly(lactic acid) (PLA) and poly(butylene adipate-co-terephthalate) (PBAT) are biodegradable aliphatic polyesters, which being semicrystalline and thermoplastic can be processed by conventional methods. Their blends give interesting materials for industrial packaging applications, due to their increased ductility as PBAT content increases. However, like many aliphatic polyesters, the PLA matrix degrades upon melt processing thus affecting the thermo-mechanical features of the blended material. In this work, we studied the effect of processing at high temperature on the molecular weight distribution, morphology, and thermo-mechanical properties of both homopolymers, as well as the PLA/PBAT 75/25 blend. Notably, different processing conditions were adopted in terms of temperature (range 150-200 °C) and other relevant processing parameters (moisture removal and nitrogen atmosphere). Analysis of PLA/PBAT blends indicated that intermolecular chain reactions took place under strong degradative conditions of PLA, yielding PLA/PBAT mixed chains (copolymers). Increasing amounts of copolymers resulted in improved phase dispersion and increased ductility, as SEM and mechanical tests indicated. Conversely, reduced PLA degradation with less copolymer formation, afforded higher modulus materials, owing to poorer dispersion of the soft phase (PBAT) into the PLA matrix.     

Improvement of compatibility,mechanical, thermal and dielectric properties of poly(lactic acid) and poly(butylene adipate-co-terephthalate) blends and their composites with porous clay heterostructures from mixed surfactant systems

In this study, nanocomposite poly(lactic acid) and poly(butylene adipate-co-terephthalate) (PLA/PBAT) blends were prepared through polymer blending in the presence of multi-functional epoxy as a compatibilizer that could react with epoxy group and terminated end group of two phases to increase interfacial adhesion between PLA and PBAT and improve the toughness of PLA. The effects of porous clay heterostructure from mixed CTAB:CTAC surfactant in the mole ratio of 1:2 (B1C2-PCH) were also investigated. The elongation at break of the blends reached 38%, which was eight times that of neat PLA. The cryo-fractured surface demonstrated the interfacial adhesion caused by the interaction of the epoxy group of the reactive compatibilizer with the terminal carboxyl and hydroxyl groups of PLA and PBAT. Moreover, PBAT reduced the crystallization rate and percent crystallinity of the PLA matrix and further decreased when compatibilizer was used. Alternatively, B1C2-PCH accelerated the heterogeneous nucleation and crystallization of the nanocomposite films. After adding small amount of B1C2-PCH, the nanocomposite films demonstrated excellent dielectric properties. Therefore, the improvement of PLA/PBAT nanocomposite blends are capable to be further developed as polymeric capacitor films.     

Toughening Poly(lactic acid) with Imidazolium-based Elastomeric Ionomers

Imidazolium-based elastomeric ionomers (i-BIIR) were facilely synthesized by ionically modified brominated poly(isobutylene-co-isoprene) (BIIR) with different alkyl chain imidazole and thoroughly explored as novel toughening agents for poly(lactic acid) (PLA). The miscibility, thermal behavior, phase morphology and mechanical property of ionomers and blends were investigated through dynamic mechanical analyses (DMA), differential scanning calorimetry (DSC), scanning electron microscopy (SEM), tensile and impact testing. DMA and SEM results showed that better compatibility between the PLA and i-BIIR was achieved compared to the PLA/unmodified BIIR elastomer. A remarkable improvement in ductility with an optimum elongation at break up to 235% was achieved for the PLA/i-BIIR blends with 1-dodecylimidazole alkyl chain (i-BIIR-12), more than 10 times higher than that of pure PLA. The impact strengths of PLA were enhanced from 1.9 kJ/m² to 4.1 kJ/m² for the PLA/10 wt% i-BIIR-12 blend. Toughening mechanism had been established by systematical analysis of the compatibility, intermolecular interaction and phase structures of the blends. Interfacial cavitations initiated massive shear yielding of the PLA matrix owing to a suitable interfacial adhesion which played a key role in the enormous toughening effect in these blends. We believed that introducing imidazolium group into the BIIR elastomer was vital for the formation of a suitable interfacial adhesion.     

The effect of free radical reactions on structure and properties of poly(lactic acid) (PLA) based blends

The blending of PLA with poly(butylene-adipate-co-terephthalate) (PBAT) is a promising strategy to achieve a toughened multiphase material. The blends ductility could be further improved through reactive compatibilization, i.e. inducing the formation of comb PLA-PBAT copolymers during the melt blending. In the present work a non-selective strategy was adopted which consisted in the use of a peroxide, 2,5-Dimethyl-2,5-di(tert-butylperoxy)hexane. The phase morphology development and the final properties (torque, fluidity in the melt, tensile behaviour, thermal and dynamical-mechanical features) of the blends were studied as a function of the peroxide concentration. The elongation at break was improved up to a maximum value thanks to this approach and a corresponding minimum was observed in the value of the dispersed phase diameter. A structural characterization of the macromolecules formed during the reactive process was attempted by using size exclusion chromatography of the blends and comparison with the pure polymers obtained by processing in the presence of the peroxide.     

Biodegradation behavior of poly(butylene adipate-co-terephthalate) (PBAT), poly(lactic acid) (PLA), and their blend under soil conditions

Poly(lactic acid) (PLA) and poly(butylene adipate-co-terephthalate) (PBAT) were mixed at a ratio of 40:60, extruded to form granules and cast into film; then, the PLA, PBAT, and PBAT/PLA film samples were buried in real soil environments. The residual degraded samples were taken regularly from the soil and analyzed by SEM, DSC, TGA, IR spectroscopy and elemental analysis. The analyses showed that PBAT and PLA had different biodegradation mechanisms. Further, the melting temperature and the melting point change of the various components in the PBAT/PLA blend before and after the biodegradation essentially followed the process of the changes in the respective single polymers. After biodegradation, the carbon atom content in the molecular structure of the PBAT, PLA, and PBAT/PLA samples decreased, while the oxygen atom content increased, indicating that the samples indeed degraded. The biodegradation rates of PBAT and PLA in the PBAT/PLA blend were not the same as those for the single materials.     

Evaluation and comparison of mid-infrared,Raman and near-infrared spectroscopies for characterization and determination of the compositions in fully biodegradable poly(lactic acid)/poly(propylene carbonate)/poly(butylene adipate-co-terephthalate) blends combined with chemometrics

In this work, mid-infrared (MIR), Raman and near-infrared (NIR) spectroscopies were evaluated and compared for characterization and determination of the compositions in poly(lactic acid)/poly(propylene carbonate)/poly(butylene adipate-co-terephthalate) (PLA/PPC/PBAT) blends via chemometrics. Qualitative analysis of MIR, Raman, and NIR spectra of the three compositions was performed. Partial least squares (PLS) models were developed based on each spectroscopy for quantitative determination of the concentrations. The data suggested that MIR and Raman have an advantage over NIR in terms of qualitative recognition of the three compositions. The data also showed that Raman and NIR succeeded in determining the concentrations, while the concentration determined via MIR was inaccurate. Hence, Raman is the optimal analytical tool for qualitative characterization and quantitative determination of the compositions in fully biodegradable PLA/PPC/PBAT blends. The characteristic bands in the Raman spectra clearly identify PLA, PPC, and PBAT to be 392 cm^?1 (δ CCO), 948 cm^?1 (ν C?O?C) and 1600 cm^?1 (ν C ? C in benzene ring), respectively. The optimal calibration models based on Raman for PLA, PPC, and PBAT exhibited root mean square error of prediction (RMSEP) values of 3.140%, 3.576%, and 2.538%, respectively.     

Increased covalent conjugation of a model antigen to poly(lactic acid)-g-maleic anhydride nanoparticles compared to bare poly(lactic acid) nanoparticles

Maleic anhydride (MA) grafted poly(lactic acid) (PLA) (PLA-g-MA) was synthesized from PLA. Proton nuclear magnetic resonance confirmed the grafting of the MA. PLA-g-MA and PLA were used to prepare polymeric nanoparticles. Particle size distributions were measured by dynamic light scattering, and colloidal stability was determined by (zeta) ζ-potential. The ζ-potential becomes more negative for PLA-g-MA than PLA nanoparticle dispersions, due to the presence of deprotonated carboxylic acid groups on the backbone of the PLA and confirms the MA grafting results. Maleic anhydride grafted on PLA backbone improves the covalent conjugation with ovalbumin (OVA) compared to OVA physically adsorbed on the particles. The chemical conjugation was carried out via amide linkages between the carboxylic groups of the nanoparticles, activated with 1-ethyl-3-(3-dimethylaminopropyl)carbodiimide, and the amino groups of the protein. The amount of protein conjugated was measured by using the bicinchoninic acid method and is threefold higher compared to the adsorbed OVA. Moreover, the PLA-g-MA nanoparticles increased the amount of conjugated OVA by 36 wt% compared to PLA nanoparticles. OVA adsorption and OVA conjugation provided colloidal dispersions with excellent stability.     

Thermal,mechanical and electroactive shape memory properties of polyurethane (PU)/poly (lactic acid) (PLA)/CNT nanocomposites

Polymer blend nanocomposites based on thermoplastic polyurethane (PU) elastomer, polylactide (PLA) and surface modified carbon nanotubes were prepared via simple melt mixing process and investigated for its mechanical, dynamic mechanical and electroactive shape memory properties. Chemical and structural characterization of the polymer blend nanocomposites were investigated by Fourier Transform infrared (FT-IR) and wide angle X-ray diffraction (WAXD). Loading of the surface modified carbon nanotube in the PU/PLA polymer blends resulted in the significant improvement on the mechanical properties such as tensile strength, when compared to the pure and pristine CNT loaded polymer blends. Dynamic mechanical analysis showed that the glass transition temperature (T_g) of the PU/PLA blend slightly increases on loading of pristine CNT and this effect is more pronounced on loading surface modified CNTs. Thermal and electrical properties of the polymer blend composites increases significantly on loading pristine or surface modified CNTs. Finally, shape memory studies of the PU/PLA/modified CNT composites exhibit a remarkable recoverability of its shape at lower applied dc voltages, when compared to pure or pristine CNT loaded system.     

Compatibilizing effects for improving mechanical properties of biodegradable poly (lactic acid) and polycarbonate blends

Mechanical, morphological and rheological properties of polycarbonate (PC) and poly (lactic acid) (PLA) blends with compatibilizers have been investigated. Three types of compatibilizers were used: poly(styrene-g-acrylonitrile)-maleic anhydride (SAN-g-MAH), poly(ethylene-co-octene) rubber-maleic anhydride (EOR-MAH) and poly(ethylene-co-glycidyl methacrylate) (EGMA). The maximum value of the mechanical properties such as impact and tensile strengths of the PC/PLA (70/30, wt%) blend before or after hydrolysis was observed when the SAN-g-MAH was used as a compatibilizer at the amount of 5 phr. From the interfacial tension between PC and PLA which was determined from the weighted relaxation spectra using Palierne emulsion model, minimum value of interfacial tension (0.08 mN/m) was observed when the SAN-g-MAH (5 phr) was used. From the morphological studies of the PC/PLA (70/30) blends, the PLA droplet size showed minimum (0.19 μm) at the 5.0 phr SAN-g-MAH. From the results of mechanical, morphological and rheological properties of the PC/PLA (70/30) blend, it is suggested that the SAN-g-MAH is the most effective compatibilizer to improve the mechanical strength of the PC/PLA (70/30) blends among the compatibilizers used in this study, especially at the amount of 5 phr.     

Morphology and properties of super-toughened bio-based poly(lactic acid)/poly(ethylene-co-vinyl acetate) blends by peroxide-induced dynamic vulcanization and interfacial compatibilization

Super-toughened poly(lactic acid) (PLA)/poly(ethylene-co-vinyl acetate) (EVA) blends were prepared via 2,5-dimethyl-2,5-di(tert-butylperoxy)hexane (AD) induced dynamic vulcanization and in situ interfacial compatibilization. The effects of AD on the morphology and properties of PLA/EVA blends were studied using a Brabender torque rheometer, gel content test, scanning electron microscopy (SEM), differential scanning calorimetry (DSC) thermogravimetric analysis (TGA) and mechanical properties test. The torque and gel content demonstrated that EVA and PLA was successfully vulcanized in the presence of free radicals obtained by the decomposition of the 2,5-dimethyl-2,5-di(tert-butylperoxy)hexane (AD). Additionally, the gel content results indicated that, compared with PLA, EVA is more aggressive with free radicals. The SEM revealed that a relatively uniform phase morphology and good interfacial compatibilization were achieved in the dynamically vulcanized PLA/EVA/AD blends. The interfacial reaction and compatibilization between the component polymers resulted in the formation of super-toughened PLA/EVA blended materials.     

Effect of poly (lactic acid)‐graft‐glycidyl methacrylate as a compatibilizer on properties of poly (lactic acid)/banana fiber biocomposites

The main aim of this study was to synthesis of poly (lactic acid) (PLA)‐graft‐glycidyl methacrylate (GMA) as well as its influence on the properties of PLA/banana fiber biocomposites. PLA‐graft‐GMA graft copolymer (GC) was synthesized by melt blending PLA with GMA using benzoyl peroxide and dicumyl peroxide as initiators. Graft copolymerization was confirmed by FTIR and ¹H‐NMR spectroscopic studies. PLA/silane treated banana fiber (SiB) biocomposites with various GC concentrations were prepared by melt blending followed by injection molding techniques. The influence of GC content on the mechanical, thermal and moisture resistance properties of the composite was investigated. The addition of 15 wt% GC content in the biocomposite provided optimum tensile and flexural strength, which is attributed to the greater compatibility between fiber and PLA matrix. The thermal properties of biocomposites have been evaluated using thermogravimetric analysis which provided evidence of improved interfacial adhesion between SiB and PLA by the addition of GC. Additionally, GC enhanced the moisture absorption resistance of biocomposites. These results indicated that GC is indeed a good candidate as a compatibilizing agent to improve the compatibility in PLA/fiber biocomposites. Copyright © 2015 John Wiley & Sons, Ltd.     

Water‐disintegrative and biodegradable blends containing poly(L‐lactic acid) and poly(butylene adipate‐co‐terephthalate)

In this study, novel biodegradable materials were successfully generated, which have excellent mechanical properties in air during usage and storage, but whose structure easily disintegrates when immersed in water. The materials were prepared by melt blending poly(L ‐lactic acid) (PLLA) and poly(butylene adipate‐co‐terephthalate) (PBAT) with a small amount of oligomeric poly(aspartic acid‐co‐lactide) (PAL) as a degradation accelerator. The degradation behavior of the blends was investigated by immersing the blend films in phosphate‐buffered saline (pH = 7.3) at 40 °C. It was shown that the PAL content and composition significantly affected morphology, mechanical properties, and hydrolysis rate of the blends. It was observed that the blends containing PAL with higher molar ratios of L ‐lactyl [LA]/[Asp] had smaller PBAT domain size, showing better mechanical properties when compared with those containing PAL with lower molar ratios of [LA]/[Asp]. The degradation rates of both PLLA and PBAT components in the ternary blends simultaneously became higher for the blends containing PAL with higher molar ratios of [LA]/[Asp]. It was confirmed that the PLLA component and its decomposed materials efficiently catalyze the hydrolytic degradation of the PBAT component, but by contrast that the PBAT component and its decomposed materials do not catalyze the hydrolytic degradation of the PLLA component in the blends. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2010     

Toughening of poly(lactic acid) by ethylene-co-vinyl acetate copolymer with different vinyl acetate contents

The well-known bio-based and biocompostable poly(lactic acid), PLA, suffers from brittleness and a low heat distortion temperature. In this paper, we address a possible route to make PLA tough(er) by blending with ethylene-co-vinyl acetate (EVA) with different vinyl acetate contents. The compatibility and phase morphology of the PLA/EVA blends was controlled by the ratio of vinyl acetate and ethylene in the random copolymers. Tough PLA/EVA blends with increased impact toughness, up to a factor of 30, were obtained with a maximum toughness at a vinyl acetate content of approximately 50 wt.%. The local deformation mechanism was well studied by TEM, SAXS and SEM. It revealed that internal rubber cavitation in combination with matrix yielding is the dominant toughening mechanism for the PLA/EVA blends under both impact and tensile testing conditions.     

Electrospun fibers of poly(ethylene terephthalate) blended with poly(lactic acid)

Fibrous blends of polyethylene terephthalate (PET) and polylactic acid (PLA) were fabricated by electrospinning (ES) from a common solvent, at concentrations of PET/PLA = 100/0, 70/30, 50/50, 30/70, and 0/100. Oriented fiber mats were studied either as-spun, or after a cold-crystallization treatment. Scanning electron microscopy of as-spun amorphous fibers showed that addition of PLA into the ES solution prevents occurrence of beads. In some compositions, two glass transitions were observed by temperature-modulated differential scanning calorimetry indicating that the two components in the ES fibers were phase separated. Thermogravimetric analysis was used to study thermal degradation at high temperatures. PLA degrades at a temperature about 100 °C lower than that of PET, and holding or cycling the blends to high temperature can result in the degradation of PLA. Degree of crystallinity was determined using DSC for as-spun and cold-crystallized ES blend fibers. The degree of crystallinity of each blend component is reduced by the presence of the other blend component, and the overall crystallinity of the blend fibers is less than that of the homopolymer fibers. Wide-angle X-ray scattering results show that oriented crystals were formed in the blended electrospun fibers collected on a rotating collector. The cold-crystallization process leads to both PET and PLA crystallizations. Oriented crystallites form even when the fiber is crystallized with its ends free to shrink.     

Enhancing toughness of poly (lactic acid)/Thermoplastic polyurethane blends via increasing interface compatibility by polyurethane elastomer prepolymer and its toughening mechanism

Due to the environmental pollution caused by the petroleum-based polymer, poly (lactic acid) (PLA), a biodegradable and biocompatible polymer that obtained from natural and renewable sources, has attracted widespread attention. However, the brittleness of PLA greatly limits its application. In this study, the super toughened PLA-based blends were obtained by compatibilizing the PLA/thermoplastic polyurethane (TPU) blends with the polyurethane elastomer prepolymer (PUEP) as an active compatibilizer. The mechanical properties, thermal properties and corresponding toughening mechanism of PLA/TPU/PUEP system were studied by tensile test, instrumented impact test, dynamic mechanical analysis (DMA), scanning electronic microscope (SEM), differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA). All the results demonstrate that the isocyanate (−NCO) group in PUEP is successfully reacted with the –OH groups at both sides of the PLA and the obtained polyurethane (PU)~PLA copolymer (PU ~ cõ PLA) significantly improves the interfacial compatibility of PLA/TPU blends. The gradually refined dispersed phase size and fuzzy phase interface as displayed in SEM images suggest a good interfacial compatibilization in the PLA/TPU/PUEP blends, probably due to the isocyanate reaction between PLA and PUEP. And the interfacial reaction and compatibilization among the components led to the formation of super toughened PLA/TPU/PUEP blends. And the instrumented impact results indicate that most of the impact toughness is provided by the crack propagation rather than the crack initiation during the entire fracture process.     

Morphological behaviour of poly(lactic acid) during hydrolytic degradation

The hydrolytic degradation and the morphological behaviour of a packaging grade of poly(lactic acid) (PLA) were characterized by a series of techniques. During the initial degradation process (stage 1) at a temperature near the glass transition temperature (T_g), the molecular weight of PLA decreased as degradation time increased following a bulk erosion mechanism while the crystallinity increased simultaneously, but no observable weight loss occurred at stage 1. Mainly α-form PLA crystal structure was formed for the crystalline PLA with a low content of d stereo-isomers, but the material displayed a lower regularity, smaller domain size, lower melting temperatures T_m and different motional dynamics as compared to the original PLA with a similar level of crystallinity achieved by annealing. The amorphous PLA with a higher amount of d stereo-isomers also yielded the α crystalline phase as well as stereo-complex crystals at stage 1. When the molecular weight and the crystallinity reached a stable level, PLA started erosion into the degrading aqueous medium. During this stage of degradation (stage 2), the crystalline structure in PLA residues was further modified and both pH and temperature influenced the modification. The degradation at stage 2 was likely to follow a surface erosion mechanism with lactic acid as the major product of the weight loss. Besides the crystallinity effect on the degradation, temperature also played a key role in determining the rate of PLA degradation in both stages. The process was very slow at temperatures below the T_g of PLA but the rate was greatly enhanced at temperatures above the T_g.     

Evaluation of PLA content in PLA/PBAT blends using TGA

The thermogravimetric analysis (TGA) was used to evaluate the polylactide (PLA) content in PLA/poly(butylene adipate-co-terephthalate) (PLA/PBAT) blends. The TGA curves of PLA/PBAT blends containing magnesium oxide (MgO) can clearly show two-step weight loss profiles because PLA can be selectively depolymerized in PLA/PBAT blends under the catalysis of MgO, and thus the PLA content can be determined according to the TGA curve for the blends. The detection scope of this method is especially applicable to the PLA content in the range of 10–90 wt% in PLA/PBAT blends at a heating rate 10 °C·min⁻¹. The measurement reliability was evaluated by parallel experiments. When the PLA content was 20, 50 and 80 wt%, the standard deviation (STDEV) and the absolute error for the measurements were less than 2.0 wt% and ±1.0 wt%, respectively, which indicated that the method is sufficiently reliable.     

生物基超韧聚乳酸复合材料的制备与性能

采用来源于可再生资源的聚醚酰胺弹性体（PEBA）增韧聚乳酸（PLA）制备超韧聚乳酸（PLA/PEBA-GMA）复合材料.为了提高PEBA与PLA之间的相容性,选择极性单体甲基丙烯酸缩水甘油酯（GMA）、共接枝单体乙烯基吡咯烷酮（NVP）及引发剂过氧化二异丙苯（DCP）对PEBA进行接枝改性制备PEBA-GMA.研究了接枝单体组分的用量（m/g）对PLA/PEBA-GMA复合材料性能的影响.研究发现,随着接枝单体组分用量的提高,复合材料的缺口冲击强度逐渐增大,当接枝单体组分GMA,NVP和DCP的用量分别为2.5,2.5和0.25 g时,复合材料的冲击强度高达88.6 kJ/m²,断裂伸长率为164.1%.研究表明,在熔融共混过程中,聚乳酸的端基（—OH和—COOH）与PEBA-GMA上环氧基团发生反应,有效改善两相间的界面相容性,随着接枝单体组分比例的提高,分散相PEBA-GMA的粒子尺寸逐渐减小且分布均匀.