Sensitive and Facile Determination of Catechol and Hydroquinone Simultaneously Under Coexistence of Resorcinol with a Zn/Al Layered Double Hydroxide Film Modified Glassy Carbon Electrode

A stable dihydroxybenzene sensor was fabricated by electrochemical deposition of Zn/Al layered double hydroxide film on glassy carbon electrode (LDHf/GCE). The sensitive and facile electrochemical method for the simultaneous determination of catechol (CA) and hydroquinone (HQ) under coexistence of resorcinol (RE) has been achieved at the LDHf/GCE in phosphate buffer solution (pH 6.5). Under the optimized conditions, the differential pulse voltammetry response of the modified electrode to CA (or HQ) shows a linear concentration range of 0.6 μM to 6.0 mM (or 3.2 μM to 2.4 mM) with a correlation coefficient of 0.9987 (or 0.9992) and the calculated limit of detection is 0.1 μM (or 1.0 μM) at a signal‐to‐noise ratio of 3. In the presence of 50 μM isomer, the linear concentration ranges for CA and HQ are 3.0 μM to 1.5 mM and 12.0 μM to 0.8 mM, respectively. The detection limits are 1.2 μM and 9.0 μM. Further, the proposed method has been performed to successfully detect dihydroxybenzene isomers in analysis of real samples, such as water and tea.     

Sensitive determination of diuron on zinc oxide nanoparticles modified carbon paste electrode in soil and water samples

An electrochemical sensor based on Zinc oxide nanoparticles (ZnONPs) modified carbon paste electrode was designed for the toxic diuron pesticide detection. The ZnONPs were synthesized through the hydrothermal route and their structural properties were investigated via scanning electron microscopy (SEM) and X-ray diffraction powder (XRD). The designed ZnONPs-modified carbon paste electrode (ZnONPs-CPE) was characterized using cyclic voltammetry and electrochemical impedance spectroscopy. The sensor showed significantly enhanced sensitivity on the diuron oxidation peak current, compared to the bare carbon paste electrode. Qualitative and quantitative analysis were performed using cyclic voltammetry (CV) and square wave voltammetry (SWV). Experimental parameters such as pH, amount of ZnONPs and frequency were evaluated and the optimized conditions were obtained with 0.1 M phosphate buffer solution at pH=8, a frequency of 50 Hz and a quantity of 5 mg of ZnONPs. Under these conditions, linear responses ranging from 1.3 to 7.7 μM and 8.6 to 30 μM of diuron were obtained, with correlation coefficients of R²=0.994 and 0.996 respectively. Detection and quantification limits of 0.22 μM and 0.84 μM (S/N=3) were respectively achieved based on the 3σ method. The interference of some ions on the oxidation peak of diuron on ZnONPs-CPE was also evaluated and no interference was observed, therefore demonstrating the selectivity of the sensor. The proposed sensor, designed with ecofriendly materials, is sensitive, selective and was effectively used for diuron determination in soils and water samples with recoveries ranging from 98 % to 101.5 %.     

A Simple and Highly Selective Determination of Telmisartan at Sodium Dodecyl Sulfate Modified Pyrolytic Graphite Surface

A simple, facile, selective and cost effective electrochemical method is proposed for the determination of telmisartan (TMS); a drug used for hypertension. A sodium dodecyl sulfate (SDS) modified edge plane pyrolytic graphite (EPPG) is prepared by simple immersion of EPPG in SDS solution at concentration greater than critical micelle concentration (CMC). The modified sensor exhibited superior sensing properties towards the oxidation of TMS. The modified surface was characterized by using the Energy dispersive X‐ray analysis, Field Emission Scanning Electron Microscopy, Electrochemical Impedance Spectroscopy and cyclic voltammetry. The quantitative investigations of the TMS were performed by applying the square wave voltammetry. The micelles of SDS form a pseudo complex with cation radical of TMS and catalyse the oxidation. The proposed sensor shows the linear calibration plot in the concentration range of 5–100 μM with sensitivity 0.2983 μA/μM and the limit of the detection of the sensor was found to be 0.082 μM. The specificity of the developed sensor was also evaluated in the presence of commonly present interfering substances in biological samples. The amount of TMS excreted in urine of the patients undergoing treatment has also been determined. The proposed method can be effectively applied for the investigation of TMS in pharmaceutical formulations and biological samples.     

毛细管区带电泳法测定复方磷酸可待因溶液有效成份

应用毛细管电泳法测定了复方磷酸可待因溶液中磷酸可待因、盐酸麻黄碱、扑尔敏的含量。毛细管电泳的条件为 :37cm× 5 0 μm i.d(有效长度 30 cm)未涂层石英毛细管柱 ;分离电压 :1 5 k V;缓冲溶液 1 5 0 mmol/L NH4 Ac- H3PO4 ( p H2 .0 )。研究了方法的线性范围、精密度、回收率等 ,测定了三批样品。实验证明方法简便、快速、准确     

A Sensitive Electrochemical Sensor for Voltammetric Determination of Ganciclovir Based on Au‐ZnS Nanocomposite

An electrode modified with ZnS and gold nanoparticles (Au‐ZnS NPs) is introduced for highly sensitive voltammetric determination of ganciclovir (GCV). Surface structure and topography of the modified electrode was studied by SEM, EDX and XRD techniques. Electrochemical oxidation of GCV was investigated by cyclic (CV) and square wave voltammetry (SWV) in Briton‐Robinson buffer solution (pH 1.5). The results showed that electrochemical oxidation of GCV at the Au‐ZnS modified glassy carbon electrode (GCE) is irreversible and exhibited diffusion controlled electrode process over the pH range from 1.0 to 6.0. The oxidation potential peak and pH relationship showed that electrons and protons were transferred simultaneously over the electrochemical oxidation process. Using the proposed sensor, the linear calibration curves were obtained in the ranges of 0.04–1.50 μM and 1.5–70.0 μM with detection limit of 0.01 μM GCV by SWV technique. The modified electrode was successfully applied as a sensitive, reproducible and repeatable sensor for determination of the trace amount of GCV in human serum, urine and cymevene vials. Reasonable results were obtained from comparing the measurements of the real samples by the new sensor to high performance liquid chromatography (HPLC) as a standard method.     

Differential Pulse Voltammetric Determination of Local Anesthetics Heptacaine,Carbisocaine and Pentacaine at DNA Modified Screen‐Printed Electrode

A procedure for the differential pulse voltammetric determination of three local anesthetics (Heptacaine, Carbisocaine and Pentacaine) at a screen‐printed electrode surface modified with the dsDNA layer is described. The detection limits obtained after 120 s drug accumulation from 0.01 M phosphate buffer solution pH 6.96 are 0.02 μM (Pentacaine) and 0.03 μM (Carbisocaine and Heptacaine). The method was applied to the determination of Carbisocaine in spiked serum.     

Electrochemical Characteristics and Electrosensing of an Antiviral Drug,Entecavir via Synergic Effect of Graphene Oxide Nanoribbons and Ceria Nanorods

A sensitive electrochemical sensor was fabricated based on ceria‐graphene oxide nanoribbons composite (CeO₂‐GONRs) for an antiviral drug, entecavir (ETV). It was characterized by SEM, EDAX, AFM, IR and Raman spectroscopic techniques. The electrochemical behaviour of ETV was investigated by cyclic voltammetric, differential pulse voltammetric (DPV), linear sweep voltammetric (LSV) and square wave voltammetric (SWV) methods at CeO₂‐GONRs modified glassy carbon electrode. Good linearity was observed between the peak current and concentration of ETV in the range of 0.51 ‐ 100 μM with a detection limit of 0.042 μM in DPV method, 2.1 – 61.1 μM with a detection limit of 0.7 μM in LSV method and 0.1 ‐ 80 μM with a detection limit of 68.1 nM in SWV method. The proposed sensitive DPV method was successfully applied for the determination ETV in tablets and biological samples.     

Fabrication of an optical sensor based on the immobilization of Qsal on the plasticized PVC membrane for the determination of copper(II)

A novel optical sensor has been proposed for sensitive determination of Cu(II) ion in aqueous solutions. The copper sensing membrane was prepared by incorporating Qsal (2-(2-hydroxyphenyl)-3H-anthra[2,1-d]imidazole-6,11-dione) as ionophore in the plasticized PVC membrane containing tributyl phosphate (TBP) as plasticizer. The membrane responds to Cu(II) ion by changing color reversibly from yellow to dark red in acetate buffer solution at pH 4.0. The proposed sensor displays a linear range of 6.3 × 10^?7?1.00 × 10^?4 M with a limit of detection of 3.3 × 10^?7 M. The response time of the optical sensor was about 3?C5 min, depending on the concentration of Cu(II) ions. The selectivity of the optical sensor to Cu(II) ions in acetate buffer is good. The sensor can readily be regenerated by hydrochloric acid (0.1 M). The optical sensor is fully reversible. The proposed optical sensor was applied to the determination of Cu(II) in environmental water samples.     

A Novel Hybrid Nano‐composite Grafted Electrochemically Reduced Graphene Oxide Based Sensor for Sensitive Determination of Efavirenz

A novel, facile fabrication, based on electrochemically reduced graphene oxide (ErGO), grafted with Pt nanoparticles and Nafion hybrid nano‐composite (ErGO‐Pt/Nafion) on the surface of edge plane pyrolytic graphite (EPPG) has been reported. The fabricated sensor has been used for the sensitive and selective determination of efavirenz (EFZ), a well‐known drug for HIV infections. The ErGO‐Pt/Nafion film was characterized by Field Emission Scanning Electron Microscopy (FE‐SEM), Energy‐dispersive X‐ray spectrometry (EDS) and Electrochemical Impedance Spectroscopy (EIS). The experimental results reveal that the modified sensor displays an excellent electrocatalytic activity towards the oxidation of EFZ and exhibits a large linear dynamic relationship in the range of 0.05 μM to 150 μM, with a detection limit of 1.8 nM. Practical utility of the developed sensor has been demonstrated by determining the EFZ in biological fluids and pharmaceutical samples and a low detection limit with high sensitivity observed makes it valuable for the clinical diagnosis.     

An indicator-displacement assay for naked-eye detection and quantification of histidine in human urine

A simple and efficient colorimetric method for the naked-eye detection and quantification of histidine in biological fluids was developed based on an indicator-displacement assay (IDA) and the Ni(2+)-histidine affinity pair. In this IDA approach, a commercially available dye, murexide, was used as the indicator and the selective detection of histidine was achieved based on the competition between indicator and histidine for the binding with Ni(2+). The competition of histidine with murexide for Ni(2+) resulted in an obvious color change of the solution from yellow to purple, and the permitted naked-eye detection of trace histidine. The developed bioassay allows the rapid, sensitive and selective detection of histidine in urine samples, and does not need complicated sample pretreatment. The detection limit was 0.4 μM with a linear range from 2 to 30 μM. The relative standard deviation for 11 replicate detections of 8 μM histidine was 2.0%. The developed sensor was successfully applied to the determination of histidine in human urine samples with recoveries from 97 to 105%.     

Penicillamine determination using a tyrosinase micro-rotating biosensor

Tyrosinase [EC 1.14.18.1], immobilized on a rotating disk, catalyzed the oxidation of catechols to o-benzoquinone, whose back electrochemical reduction was detected on glassy carbon electrode surface at −150 mV versus Ag/AgCl/NaCl 3 M. Thus, when penicillamine (PA) was added to the solution, this thiol-containing compound participate in Michael type addition reactions with o-benzoquinone to form the corresponding thioquinone derivatives, decreasing the reduction current obtained proportionally to the increase of its concentration. This method could be used for sensitive determination of PA in drug and human synthetic serum samples. A linear range of 0.02–80 μM (r = 0.999) was obtained for amperometric determination of PA in buffered pH 7.0 solutions (0.1 M phosphate buffer). The biosensor has a reasonable reproducibility (R.S.D. < 4.0%) and a very stable amperometric response toward this compound (more than 1 month).     

Determination of anti‐malaria agent chloroquine using single drop liquid‐liquid‐liquid microextraction

A simple, sensitive, and inexpensive single drop liquid‐liquid‐liquid microextraction combined with isocratic RP‐HPLC and UV detection was developed for the determination of anti‐malaria drug, chloroquine. The target compound was extracted from alkaline aqueous sample solution (adjusted to 0.5 mol/L sodium hydroxide) through a thin layer of organic solvent membrane and back‐extracted to an acidic acceptor drop (adjusted to 0.02 mol/L phosphoric acid) suspended on the tip of a 25 μL HPLC syringe in the organic layer. This syringe was also used for direct injection after extraction. The linear range was 1–200 μg/L. The LOD and LOQ were 0.3 and 1.0 μg/L, respectively. Intra‐and inter‐day precisions were less than 2.0 and 2.3%, respectively. The real samples were successfully analyzed using the proposed method. The recoveries of spiked samples were more than 94.6%.     

A Novel Sensitive and Selective Amperometric Detection Platform for the Vanillin Content in Real Samples

Accurate and sensitive determination of vanillin in commercial samples is significant for food safety & quality. In the proposed study, copper particles were coated on an indium tin oxide electrode (ITO) by cyclic voltammetry (CV) for the determination of vanillin in food samples. CV studies indicated that the electrodeposition of Cu particles provides a good electrocatalytic effect towards the oxidation of vanillin. The fabricated sensor determines vanillin linearly between 0.50 μM–2.0 mM (Limit of detection: 0.15 μM). The Cu/ITO was successfully tested on vanillin samples and the recommended method provides accurate and selective determination of vanillin in daily samples.     

Fabrication of poly(4-aminobenzoic acid/<Emphasis Type="Italic">o</Emphasis>-toluidine) modified carbon paste electrode and its electrocatalytic property to the oxidation of nitrite

The poly(4-aminobenzoic acid/o-toluidine) (4-AB/OT) modified carbon paste electrode (CPE) was fabricated by consecutive cyclic voltammetry. The poly(4-AB/OT) CPE shows catalytic activity for the oxidation of nitrite in 0.1 M phosphate buffer solution (pH 7). Due to the electrostatic interaction between the negatively-charged nitrite ions and the positively-charged poly(4-AB/OT) film, the operating potential for nitrite oxidation was shifted about 240 mV to negative side, compared to bare CPE. The catalytic peak current was found to be linear with the nitrite concentration in the range of 6–600 μM, with a correlation coefficient of 0.981, using amperometry. The sensitivity and limit of detection for the poly(4-AB/OT) CPE are about 187.4 μA/mM and 3.5 μM, respectively. The possible interferences from several common ions were tested. The developed sensor was also successfully applied to the determination of nitrite concentration in a mineral water sample.     

Stability-indicating HPLC method for determination of naftazone in tablets. Application to degradation kinetics and content uniformity testing

A simple, sensitive, stability-indicating HPLC method was developed and validated for the quantitative determination of the vasoprotective drug, naftazone in presence of its degradation products. The analysis was carried out on a Nucleosil 100-5 phenyl column (250 mm × 4.6 mm, 5 μm) using a mobile phase consisting of methanol-0.02 M sodium dihydrogen phosphate mixture (60:40, v/v) of pH 6.0. The analyses were performed at ambient temperature with a flow rate of 1.0 mL/min and UV detection at 270 nm. The method showed good linearity over the concentration range of 0.1-10.0 μg/mL with a lower detection limit of 0.032 and quantification limit of 0.096 μg/mL. The suggested method was successfully applied for the analysis of naftazone in its commercial tablets. Moreover, it was utilized to investigate the kinetics of alkaline, acidic and oxidative degradation of the drug. The apparent first-order rate constants, half-life times, and activation energies of the degradation process were calculated. The pH-rate profile curve was derived. Furthermore, the proposed method was successfully applied to the content uniformity testing of naftazone tablets.     

Design and evaluation of a thorium (IV) selective optode

A novel optical sensor has been proposed for sensitive determination of thorium (IV) ion in aqueous solutions. The thorium sensing membrane was prepared by incorporating 4-(p-nitrophenyl azo)-pyrocatechol (NAP) as ionophore in the plasticized PVC membrane containing tributyl phosphate (TBP) as plasticizer. The membrane responds to thorium ion by changing color reversibly from yellow to red-brown in glycine buffer solution at pH 3.5. The proposed sensor displays a linear range of 8.66 × 10⁻⁶-2.00 × 10⁻⁴ M with a limit of detection of 6 × 10⁻⁶ M. The response time of the optode was about 8.8-12.5 min, depending on the concentration of Th (IV) ions. The selectivity of optode to Th (IV) ions in glycine buffer is good. The sensor can readily be regenerated by exposure to a solution mixture of sodium fluoride and 5-sulfosalicylic acid (dihydrate) (0.01 M each). The optode is fully reversible. The proposed optode was applied to the determination of thorium (IV) in environmental water samples.     

Nanomolar Determination of Methyldopa in the Presence of Large Amounts of Hydrochlorothiazide Using a Carbon Paste Electrode Modified with Graphene Oxide Nanosheets and 3‐(4′‐Amino‐3′‐hydroxy‐biphenyl‐4‐yl)‐acrylic Acid

A novel electrochemical sensor for sensitive detection of methyldopa at physiological pH was developed by the bulk modification of carbon paste electrode (CPE) with graphene oxide nanosheets and 3‐(4′‐amino‐3′‐hydroxy‐biphenyl‐4‐yl)‐acrylic acid (3,′AA). Applying square wave voltammetry (SWV), in phosphate buffer solution (PBS) of pH 7.0, the oxidation current increased linearly with two concentration intervals of methyldopa, one is 1.0×10^?8–1.0×10^?6 M and the other is 1.0×10^?6–4.5×10^?5 M. The detection limit (3σ) obtained by SWV was 9.0 nM. The modified electrode was successfully applied for simultaneous determination of methyldopa and hydrochlorothiazide. Finally, the proposed method was applied to the determination of methyldopa and hydrochlorothiazide in some real samples.     

Differential Pulse Anodic Stripping Voltammetric Determination of Lead (II) Using Poly Xylenol Orange Modified Electrode

In this work a method for sensitive anodic stripping voltammetric determination of Pb(II) ions using a poly xylenol orange film modified electrode (PXOFME) has been proposed. Poly xylenol orange film (PXOF) was formed on a paraffin impegrenated graphite electrode (PIGE) using electro polymerization method by scanning the potential between −0.5 V to 1.3 V, at a scan rate of 50 mV/s for 30 segments in 0.1 M phosphate buffer solution (PBS) of pH 7. The PXOFME was characterized by scanning electron microscopy (SEM), ATR‐IR spectroscopy, cyclic voltammetry (CV), differential pulse voltammetry (DPV) and electrochemical impedance spectroscopy (EIS). The modified electrode has been used to develop a sensitive method for the determination of Pb(II) ions by anodic stripping voltmmetry (ASV). The PXOFME was used to preconcentrate Pb(II) ions through complexation, the complexed metal ions were reduced electrochemically and then stripped anodically from the surface of the electrode. A linear range of 5 μg/L to 413 μg/L with a limit of detection (S/N=3) of 1.6 μg/L was observed for the determination of Pb(II) ions. The method was applied to lead determination in sea water and tap water samples and the results were found to be satisfactory.     

Single step modification of copper electrode for the highly sensitive and selective non-enzymatic determination of glucose

A non-enzymatic sensor was developed for the determination of glucose in alkaline medium by anodisation of copper in sodium potassium tartrate solution. The morphology of the modified copper electrode was studied by scanning electron microscopy, and its electrochemical behavior by cyclic voltammetry and electrochemical impedance spectroscopy. The electrode enables direct electrocatalytic oxidation of glucose on a CuO/Cu electrode at 0.7 V in 0.1 M sodium hydroxide. At this potential, the sensor is highly selective to glucose even in the presence of ascorbic acid, uric acid, or dopamine which are common interfering species. The sensor displays a sensitivity of 761.9 μA mM^?1 cm^?2, a linear detection range from 2 μM to 20 mM, a response time of <1 s, and a detection limit of 1 μM (S/N = 3). It was tested for determination of glucose level in blood serum.     

Simultaneous Trace Electrochemical Determination of Xanthine Theophylline and Theobromine with a Novel Sensor Based on a Composite Including Metal Oxide Nanoparticle Multi-walled Carbon Nanotube and Nano-Na-montmorillonite Clay

We report the simultaneous determination of purine molecules with biological significance on pencil graphite electrode (PGE) modified with a composite solution including NiO nanoparticles, multi-walled carbon nanotube (MWCNT), and natural nano-Na-montmorillonite clay (NNaM) using DPV technique. The novel sensor, NiO/MWCNT/NNaM/PGE, achieved simultaneous determination of xanthine, theophylline, and theobromine at the detection limits 0.077 μM, 0.361 μM, and 0.458 μM with the linear working ranges 0.5–150 μM, 5–200 μM, and 5–250 μM in Britton-Robinson buffer at pH 2.0, respectively. The sensor revealed excellent performance for the simultaneous determination of XT, TP, and TB in three real-world samples.