Bundling and diameter selectivity in HiPco SWNTs poly(p-phenylene vinylene-co-2,5-dioctyloxy-m-phenylene vinylene) composites

Temperature-dependent (TD) Raman measurements at laser excitation 514.5 nm were performed at different concentrations. The spectral profile of the radial breathing modes were investigated up to a polymer concentration of 1 g/L and were found to be dominated by approximately 1.2-1.4 nm diameter tubes at room temperature. Upon heating above the glass transition of the polymer (60 degrees C) the smaller tubes around approximately 0.9 nm increased significantly in relative intensity. This suggests that below the glass transition of the polymer (60 degrees C) RBMs within the composite are damped and spectral changes cannot be interpreted as diameter selective solubilization. The observed RBM damping at room temperature only occurred up to a concentration of approximately 1.2 x 10(-4) g/L and below this no damping was observed. Photoluminescence intensity (PL) measurements were taken for a range of PmPV concentrations, in which HiPco single walled carbon nanotubes (SWNTs) at 100%, 10%, 1%, 0.1%, 0.01%, and 0% mass fractions were added. Fitting of the concentration dependence to a dynamic absorption/desorption model indicates that the polymer interacts with nanotube bundles until a critical concentration of approximately 1.2 x 10(-4) g/L is reached, below which the nanotubes are isolated. The polymer and or solvent has a significant effect on the debundling and aggregation within these systems. Aggregation and/or interaction with the polymer at higher concentrations can effect the RBM profile in the composite at ambient temperatures, providing an incomplete representation of the selection of diameters present within composites at a particular wavelength.     

两种[对苯乙炔-2,5-二(十二烷氧基)对苯乙炔]共聚物的合成及性能研究

用含氯前聚物路线和Ｈｅｃｋ反应分别合成［对苯乙炔－２，５－二（十二烷氧基）对苯乙炔］无规共聚物及交替共聚物．由元素分析、凝胶渗透色谱、吸收光谱及ＤＳＣ对其进行表征，研究了共聚物的组成与导电率、溶解性及发光性能的关系．比较了无规共聚物与交替共聚物在性能上的差别．     

Structure investigation of poly(p-phenylene vinylene)

Electron diffraction patterns of highly oriented poly(p-phenylene vinylene) films obtained by the soluble polymeric precursor route are interpreted on the basis of a monoclinic unit cell containing two monomer units: c (chain axis) = 0.658 nm, a = 0.790 nm, b = 0.605 nm, α ? 123°. The molecules are nearly perfectly oriented along the stretching direction but exhibit partial axial translational disorder.     

Crystalline phases of electrically conductive poly(p-phenylene vinylene)

Poly(p-phenylene vinylene) (PPV) undergoes a first-order crystal-crystal phase transition when chemically doped with AsF₅, SbF₅, or H₂SO₄ or electrochemically oxidized with ClO^-₄ as the counterion. These structures have been observed using wide-angle x-ray diffraction. Doping with these agents does not disrupt the original orientation of the PPV crystallites. The crystalline phases obtained with all dopants employed here are similar in character, indicating a closely related family of electrically conductive structures having orthorhombic symmetry. An electrically conductive phase consisting of layers of polymer chains separated by a layer of the chemical dopant is proposed.     

Synthesis and electrical conductivity of poly(arylene vinylene). I. Poly(2,5-dimethoxyphenylene vinylene) and poly(2,5-dimethylphenylene vinylene)

The highly conjugated aromatic polymers, poly(2,5-dimethoxyphenylene vinylene) and poly(2,5-dimethylphenylene vinylene), were obtained from their water soluble, sulfonium salt precursor polymers. Films of these polymers were reacted with either AsF₅ or I₂ vapor. Poly(2,5-dimethoxyphenylene vinylene) showed increases in electrical conductivity of up to 14 to 15 orders of magnitude for these two dopants, while an 8 to 9 order of magnitude increase was observed for poly(2,5-dimethylphenylene vinylene) with the same dopants. The synthesis of the precursor polymers, the properties and elimination reactions of films of the precursors, the doping reactions, and the conductivities of the resulting phenylene vinylene films are discussed.     

Interaction of single-walled carbon nanotubes with poly(propyl ether imine) dendrimers

We study the complexation of nontoxic, native poly(propyl ether imine) dendrimers with single-walled carbon nanotubes (SWNTs). The interaction was monitored by measuring the quenching of inherent fluorescence of the dendrimer. The dendrimer-nanotube binding also resulted in the increased electrical resistance of the hole doped SWNT, due to charge-transfer interaction between dendrimer and nanotube. This charge-transfer interaction was further corroborated by observing a shift in frequency of the tangential Raman modes of SWNT. We also report the effect of acidic and neutral pH conditions on the binding affinities. Experimental studies were supplemented by all atom molecular dynamics simulations to provide a microscopic picture of the dendrimer-nanotube complex. The complexation was achieved through charge transfer and hydrophobic interactions, aided by multitude of oxygen, nitrogen, and n-propyl moieties of the dendrimer.     

Fabrication of poly(p-phenylene vinylene) (PPV) nanoheterocomposite films via layer-by-layer adsorption

The fabrication of polyelectrolyte multilayer film architectures composed of a polycation precursor (Pre-PPV) of the electroluminescent poly(p-phenylene vinylene) (PPV) and two different counter-polyanions, cellulosesulfate and poly(vinylsulfate), are reported. All multilayers were characterized by UV/VIS-spectroscopy and X-ray reflectometry. Due to the differences in spatial arrangement of charged groups, rigidity, and conformation of the polyanions, the corresponding multilayer films differ in properties such as average thickness increments and surface roughness. The adsorbed amounts per layer can be adjusted by addition of inorganic salts. Thermal conversion of Pre-PPV to PPV is achieved already slightly above 100 °C, yielding identical absorption spectra for after either 3 h at 160 °C or 20 h at 120 °C. The heat treatment causes the film thickness to be reduced by 24–40% due to elimination of dimethylsulfide and HCl and also the loss of water, but the films stay optically transparent.     

Pyridine-functionalized single-walled carbon nanotubes as gelators for poly(acrylic acid) hydrogels

Pyridine-functionalized single-walled carbon nanotubes (SWNTs) are prepared from the addition of a pyridine diazonium salt to nanotubes. The location and distribution of the functional groups is determined by atomic force microscopy using electrostatic interactions with gold nanoparticles. The pyridine-functionalized SWNTs are able to act as cross-linkers and hydrogen bond to poly(acrylic acid) to form SWNT hydrogels. The pyridine-functionalized SWNTs are further characterized using Raman, FTIR, UV/vis-NIR, and X-ray photoelectron spectroscopy and thermogravimetric analysis-mass spectrometry.     

Understanding interactions between poly(styrene-co-sodium styrene sulfonate) and single-walled carbon nanotubes

Understanding formation mechanisms of hybrids of carbon nanotubes (CNTs) wrapped by polymers and their interactions is critical in modifying solubility of CNTs in aqueous solution and developing new nanotube-based polymer materials. In the present work, we investigate the structural details of poly(styrene-co-sodium styrene sulfonate) (PSS) wrapping around the CNT and the interactions between the PSS chain and the CNT using molecular dynamics (MD) simulations. The fraction of sulfonated groups significantly influences the wrapping conformations of the PSS chain. Due to limited time scale in the MD simulations, two different initial conformations of the chains are introduced to explore the effect of the initial state on the wrapping behavior. When the chains initially wrap around the CNT in a perfect helix manner, more compact pseudo-helical conformations are obtained. For initial straight line arrangement of the chain monomers, the chains adopt looser wrapping conformations. The free-energy analysis and binding interaction of the PSS chain on the CNT surface take a glance on the relationship between the conformational transition of the chain and the energy evolution.     

Confinement crystallization of poly(l-lactide) induced by multiwalled carbon nanotubes and graphene nanosheets

Journal of Thermal Analysis and Calorimetry - Two sets of multiwalled carbon nanotubes (MWCNTs)/PLLA nanocomposites and graphene nanosheets (GNSs)/PLLA nanocomposites with various MWCNTs and GNSs...     

Theoretical investigation of substitution and end-group effects on poly(p-phenylene vinylene)s

Semi-empirical AM1 and ZINDO/S, as well as density function theory (DFT) method B3LYP/6-31G(d) quantum chemical calculations were carried out to study the electronic structures and optical properties of poly(p-phenylene vinylene) derivatives (PPVs) with 10 and 11 phenylene rings in the backbone. The calculations suggest that the assembly of alternate incorporation of CN and alkoxy substituted phenylene rings in the PPV backbone could be a good way to construct organic semiconductors with low HOMO/LUMO energy band-gaps. The effect of the end-group on the electronic structures and optical properties of the conjugated polymer was investigated by the calculated UV-Vis and UPS spectra. It was demonstrated that the aldehyde and phosphate end-groups have limited effects on the photophysical properties in the UV-visible range.     

Selective dispersion of single-walled carbon nanotubes with specific chiral indices by poly(N-decyl-2,7-carbazole)

Physico-chemical methods to sort single-walled carbon nanotubes (SWNTs) by chiral index are presently lacking but are required for in-depth experimental analysis and also for potential future applications of specific species. Here we report the unexpected selectivity of poly(N-decyl-2,7-carbazole) to almost exclusively disperse semiconducting SWNTs with differences of their chiral indices (n - m) ≥ 2 in toluene. The observed selectivity complements perfectly the dispersing features of the fluorene analogue poly(9,9-dialkyl-2,7-fluorene), which disperses semiconducting SWNTs with (n - m) ≤ 2 in toluene. The dispersed samples are further purified by density gradient centrifugation and analyzed by photoluminescence excitation spectroscopy. All-atom molecular modeling with decamer model compounds of the polymers and (10,2) and (7,6) SWNTs suggests differences in the π-π stacking interaction as origin of the selectivity. We observe energetically favored complexes between the (10,2) SWNT and the carbazole decamer and between the (7,6) SWNT and the fluorene decamer, respectively. These findings demonstrate that subtle structural changes of polymers lead to selective solvation of different families of carbon nanotubes. Furthermore, chemical screening of closely related polymers may pave the way toward simple, low-cost, and index-specific isolation of SWNTs.     

Electrochemical capacitance of the composite of poly (3,4-ethylenedioxythiophene) and functionalized single-walled carbon nanotubes

The homogenous coating of poly (3,4-ethylenedioxythiophene) (PEDOT) on carbon nanotubes was realized by using functionalization of single-walled carbon nanotubes (SWNTs) in this study. Consequently, the PEDOT/functionalized SWNTs (PEDOT/F-SWNTs) composites, with size of around 100nm, which is much smaller than that of PEDOT, were prepared by the electrochemical method. Its small granule increased the active/nonactive mass ratio and reduced the ions diffusion length. Therefore, its specific capacitance of the composite was up to 200F g^?1, which was remarkably greater than that of PEDOT. Furthermore, the PEDOT/F-SWNTs composites had very rapid charge/discharge ability with specific capacitance of 180F g^?1 at scanning rate of 200mV s^?1 and 170F g^?1 at frequency of 1Hz, which is an important practical advantage. In addition, such composite had a good cycling performance and a wide potential window.     

Heterogeneous nucleation on the crystallization poly(ethylene terephthalate)

The crystallization behavior of poly(ethylene terephthalate) (PET) with disodium terephthalate (DST) as nucleating agent was investigated. A detailed analysis of the crystallization course from the melt was made with the Avrami expression. The results demonstrated that DST additive can promote the PET crystallization rate in its entire crystallizable temperature range, and the acceleration degree of DST decreases with increasing temperature after a temperature higher than 180 °C. The values of the Avrami exponent indicated that the crystallization mode in Avrami theory is not suitable for the crystallization of these polymers, and the mechanism of the heterogeneous nucleation on PET crystallization is discussed. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 2135–2144, 2003     

Highly emissive supramolecular oligo(p-phenylene vinylene) dendrimers

pi-Conjugated oligo(p-phenylene vinylene) (OPV) guest molecules for interaction with dendritic hosts were synthesized and fully characterized by NMR spectroscopy, MALDI-TOF-MS, elemental analysis and optical measurements. The binding properties of the five different OPV guests to a N,N-bis[(3-adamantyl ureido) propyl] methylamine host have been investigated. The guests that contained an aryl urea glycine spacer were bound with the highest association constant. Subsequently, an adamantyl urea modified fifth generation poly(propylene imine) dendrimer was synthesized as a multivalent host which contains 32 N,N-bis[(3-adamantyl ureido) propyl] amine binding sites. Size exclusion chromatography showed that 32 of the OPV guests strongly bind to the fifth generation adamantyl functionalized dendritic host. In the case of the supramolecular dendritic host/guest system smooth homogeneous thin films could be obtained by spin coating. The dendritic guest-host complexes showed a significantly higher emission upon binding then that of the individual molecules due to the three-dimensional orientation of the OPV guest molecules. In the solid state, this enhancement in luminescence was a factor of 10. The pi-conjugated oligomers are less aggregated in the supramolecular assemblies presumably because of a shielding effect of the bulky adamantyl units present in the hosts.     

Effects of solvent treatment on crystallization kinetics of poly(p-phenylene sulfide)

Isothermal melt crystallization kinetics were investigated by differential scanning calorimetry (DSC) for virgin and α-chloronaphthalene solvent-treated poly(phenylene sulfide) (PPS) systems. The overall crystallization rates were found to be much faster for the solvent-treated PPS than for the virgin neat PPS. Additionally, the Avrami crystallization plot for the solvent-treated PPS samples appeared as two straight portions with an apparent discontinuity, but as a continuous straight line for the virgin PPS system. After the treatment of solvent dissolution and subsequent drying, the residual trace α-chloronaphthalene, upon being quenched to the crystallization temperatures, initiated some localized solvent-induced nuclei-like crystals in PPS. It was the nuclei that enhanced secondary crystallization in treated PPS during the second stage, and the higher extents of secondary crystallization in the solvent-treated PPS caused the apparent discontinuous break in the Avrami plots. The causes for the difference were explained and the mechanism of the sequential primary/secondary crystallization kinetics for the solvent-treated PPS was satisfactorily described with a proposed series-parallel crystallization model. ©1995 John Wiley & Sons, Inc.     

Theoretical study of the conversion of sulfonyl precursors into chains of poly(p-phenylene vinylene)

The elimination and side reactions involved in the thermal conversion of sulfonyl precursor chains into poly(p-phenylene vinylene) (PPV) have been studied in detail, using Density Functional theory, along with the MPW1K functional. The performance of the MPW1K functional for describing radical dissociation and internal conversion reactions of sulfonyl precursors has been assessed against the results of benchmark CCSD(T) calculations. Enthalpies as well as entropies are calculated at different temperatures at the level of the rigid rotor-harmonic oscillator approximation. Entropy effects on internal elimination reactions are very limited. In sharp contrast, at the temperatures under which the conversion is usually performed (550 K), entropy contributions to the activation energies are found to be very significant and to strongly favor direct radical dissociations of the precursors. Further radical side reactions following an E(i) conversion through an alkyl substituent may also significantly contribute to the formation of sp(3) defects and/or cross-linked structures in the polymer-an advantageous feature for the making of materials with improved photoluminescence efficiencies.     

Time-dependent density-functional calculations of S0-S1 transition energies of poly(p-phenylene vinylene)

We used time-dependent density-functional-theory (TDDFT) approaches to calculate absorption (S(0)-->S(1)) and emission (S(1)-->S(0)) transition energies of poly(p-phenylene vinylene) (PPV). The absorption and emission energies were estimated to be 2.44 and 2.16 eV, respectively, from the extrapolation of calculated results for oligomers. Comparisons with available experimental data demonstrated that TDDFT is a very reliable tool for investigating the electronic transitions of PPV.     

2H NMR characterization of phenylene ring flip motion in poly(p-phenylene vinylene) films

Solid-state ²H quadrupole echo nuclear magnetic resonance (NMR) spectra and measurements of ²H spin lattice relaxation times have been obtained for films of poly(p-phenylene vinylene) deuterated in phenylene ring positions (PPV-d₄). NMR line shapes show that all the phenylene rings of PPV undergo 180° rotational jumps about the 1,4 ring axis (“ring flips”) at 225°C. The temperature dependence of the ²H line shapes show that the jump motion is thermally activated, with a median activation energy, E_a = 15 kcal/mol, and a distribution of activation energies of less than ±2 kcal/mol. The jump rate was also determined from the magnitude of the anisotropic T₂ relaxation associated with ²H line shapes and from the curvature of inversion recovery intensity data. The experimental activation energy for jumps is comparable to the intramolecular potential barrier for rotation about phenylene vinylene bonds. ²H NMR provides a method for determining the phenylene-vinylene rotational barrier in pristine PPV, and may potentially be used to study conjugation in conducting films.     

Interface formation of metals and poly(p-phenylene vinylene): surface species and band bending

We used X-ray photoemission spectroscopy (XPS) to investigate the surface species of poly(p-phenylene vinylene) (PPV) and its interface formation with Ca and Al. PPV surfaces compositions varied with sample preparation. For relatively "clean'' surfaces with 4–5% O, analysis of the O 1s peak revealed four types of oxygen species, namely carbonyl (C=O), hydroxyl (C–OH), ether (C–O–C) and the carboxylic groups (HO–C=O). The oxygen groups, excluding ether, reacted with Al or Ca to form the corresponding metal oxides. Chemical interactions between the metals and the phenylene and vinylene units to yield new species were not detected. For sulfur-free surfaces, a C 1s peak shift of +0.5 eV followed the deposition of 15–30 Å of Ca on PPV. For sulfur-containing surfaces, the C 1s peak shift was −0.5 eV. We attribute this difference to the interaction of metal atoms with the sulfur impurities. For Al/PPV, a C 1s peak shift occurred at <2 Å of Al deposition and reached a constant value of about +0.4 eV after ⪅8 Å of Al. Again, the direction of the peak shift depended on the presence of sulfur impurities. We attribute the C 1s peak shifts to surface band bending and to Schottky barrier formation. Since surface oxidation of PPV can inhibit band-bending, our overall results suggest that the barrier height at the metal/PPV interface is highly sensitive to the surface preparation and relatively insensitive to the work function of the metals. The shift seen by XPS in the C 1s core level spectra of PPV points clearly to charge transfer and Schottky barrier formation at the interface as a result of metal deposition. These results imply that the metal/polymer interface is not rigid and that triangular barrier tunneling fails to take into account the effect of barrier formation. We propose a band-bending modified tunneling (BBMT) model to explain charge transfer at the Ca/polymer interface. © 1997 John Wiley & Sons, Ltd.