Influence of temperature and humidity on the degradation process of ascorbic acid in vitamin C chewable tablets

Ascorbic acid (AA) is the active ingredient of vitamin C chewable tablets. It is unstable even at room temperature, and increased temperature and humidity rapidly increase its degradation. To protect the active substance, we made its coating with polymers ethyl cellulose that provides its thermal protection and protection from moisture. We bet each particle of AA with a layer of polymer by the method of fluidization. Extra protection against thermal effects and penetration of moisture and oxygen provides the packaging. By using four kinds of packaging: polypropylene container for tablets, strips of aluminum and polyvinyl chloride Al/PVC strips, glass bottles, and strips of aluminum and polyethylene (Al.PE/PE.Al) of 3, of 6 months and of 12 months. One of the tablets are stored at room temperature (25 ± 2 °C/60% RH ± 5%), and the rest in terms of accelerated aging or increased temperature and humidity (30 ± 2 °C/65% RH ± 5% and 40 ± 2 °C/75% RH ± 5%). The speed of degradation of unprotected AA usually get doubled when there is increasing of the temperature for every 10 °C. Experimentally the concentration of AA was monitored, its oxidation product-dehydroascorbic acid and its degradation product-diketogulonic acid.     

Glycine/Glycolic acid based copolymers

Glycine/glycolic acid based biodegradable copolymers have been prepared by ring-opening homopolymerization of morpholine-2,5-dione, and ring-opening copolymerization of morpholine-2,5-dione and glycolide. The homopolymerization of morpholine-2,5-dione was carried out in the melt at 200°C for 3 min using stannous octoate as an initiator, and continued at lower reaction temperatures (100–160°C) for 2–48 h. The highest yields (60%) and intrinsic viscosities ([η] = 0.50 dL/g; DMSO, 25°C) were obtained after 3 min reaction at 200°C and 17 h at 130°C using a molar ratio of monomer and initiator of 1000. The polymer prepared by homopolymerization of morpholine-2,5-dione was composed of alternating glycine and glycolic acid residues, and had a glass transition temperature of 67°C and a melting temperature of 199°C. Random copolymers of glycine and glycolic acid were synthesized by copolymerization of morpholine-2,5-dione and glycolide in the melt at 200°C, followed by 17 h reaction at 130°C using stannous octoate as an initiator. The morphology of the copolymers varied from semi-crystalline to amorphous, depending on the mole fraction of glycolic acid residues incorporated. © 1994 John Wiley & Sons, Inc.     

Physical structure and thermal behavior of ethylcellulose

The physical structure and properties of ethylcellulose (EC) powders of different molecular weights were examined. A molecular weight in the range of 20–144 kDa with a large polydispersity was determined. EC thermal analysis revealed a glass transition at ~130 °C and a melting temperature at ~180 °C. Glass transition temperatures increased with polymer molecular weight. Wide angle (WAXS) analysis detected an amorphous broad peak at q = 1.5 Å^?1 and a distinct Bragg’s peak at 12.6 Å, which seems to be related to a supramolecular ordered structure of the polymer. These observations were confirmed using high temperature powder X-ray diffraction analysis where the crystalline peak disappeared above the melting temperature of the polymer. Ultra-small angle (USAXS) results were fitted to the Bouacage fractal unified model and fractals with an average size of 100–600 nm with a relatively smooth surface were predicted. This prediction was confirmed by transmission electron microscopy (TEM) images. According to our results, the EC polymer has a semi-crystalline structure, with crystalline domains within an amorphous background.     

TG–DSC–FTIR–MS study of gaseous compounds evolved during thermal decomposition of styrene-butadiene rubber

The thermal decomposition behavior of styrene-butadiene rubber was studied using a system equipped with thermogravimetric analysis, differential thermal analysis, Fourier transform infrared spectroscopy, and mass spectroscopy. Two different experiments were conducted. From these experiments, thermogravimetric analysis results indicated a mass loss of 58 % in the temperature range of ~290–480 °C and a mass loss of 39 % in the temperature range beyond 600 °C. Scanning electron microscopy coupled with energy-dispersive X-ray spectroscopy confirmed the presence of oxides, even at 1,000 °C, accounting for the Zn, Mg, Al, Si, and Ca in the original sample.     

Thermal stability of soil organic matter was affected by 23-yr maize and soybean continuous cultivation in northeast of China

Long-term continuous cropping affects the biochemical quality of soil organic matter (SOM), but whether the effects are relevant with their thermal stability is less clear. In northeast China, long-term continuous cropping occurred frequently owing to higher yield and economic interest requirement. To verify the thermal stability properties of SOM affected by the long-term continuous cropping, the study focused on 23-yr continuous cultivated maize and soybean plots, where the effect of cropping is likely to be detected. Bulk soils sampled in 1991 and 2014 were studied by thermogravimetry and differential scanning calorimetry (DSC). The results showed typical bimodal peaks in DSC curve in bulk Mollisols. A labile fraction peak was observed at 354–366 °C low-temperature zone and recalcitrant fraction one at high temperature of 430–438 °C. Energy density (J mg^?1 OM) was greater in soybean plots compared to maize plots; in contrast, long-term continuous maize cultivation also increased energy density, in reverse in soybean plots after 23-yr cultivation. The DSC-T₅₀, temperature at which half of energy release occurred, typically showed larger responses to long-term cultivation than crop species. Results obtained support the hypothesis of a potential link between long-term continuous cropping and the thermal stability of SOM, and a correlation with crop species.     

Hydrotalcite-derived Co-containing mixed metal oxide catalysts for methanol incineration

The Co–Mg–Al mixed metal oxides were prepared by calcination of co-precipitated hydrotalcite-like precursors at various temperatures (600–800 °C), characterised with respect to chemical (AAS) and phase (XRD) composition, textural parameters (BET), form and aggregation of cobalt species (UV–vis-DRS) and their redox properties (H₂-TPR, cyclic voltammetry). Moreover, the process of thermal decomposition of hydrotalcite-like materials to mixed metal oxide systems was studied by thermogravimetric method combined with the analysis of gaseous decomposition products by mass spectrometry. Calcined hydrotalcite-like materials were tested as catalysts for methanol incineration. Catalytic performance of the oxides depended on cobalt content, Mg/Al ratio and calcination temperature. The catalysts with lower cobalt content, higher Mg/Al ratio and calcined at lower temperatures (600 or 700 °C) were less effective in the process of methanol incineration. In a series of the studied catalysts, the best results, with respect to high catalytic activity and selectivity to CO₂, were obtained for the mixed oxide with Co:Mg:Al molar ratio of 10:57:33 calcined at 800 °C. High activity of this catalyst was likely connected with the presence of a Co–Mg–Al spinel-type phases, containing easy reducible Co³⁺ cations, formed during high-temperature treatment of the hydrotalcite-like precursor.     

Thermal analysis of synthetic (near-chabazite) zeolites with different Si/Al ratios

The thermal behaviour of synthetic K-G type zeolites (near-chabazites of Barrer) depends on their chemical composition. Samples with a Si/Si + Al fraction between 0.5 and 0.55 and consequently with a high potassium content, show a limited reversible dehydration between room temperature and 180°C. Above 180°C, after breakdown of the crystal structure, irreversible dehydration proceeds readily, with a sharp maximum near 270°C.Samples with a Si/Si + Al fraction greater than 0.57 and a lower potassium content dehydrate continuously over the whole range between room temperature and 450°C.     

Heating effect on the DSC melting curve of flaxseed oil

Flaxseed oil is rich in the alpha-linolenic acid. The effect of heating on the thermal properties of flaxseed oil extracted from flax seeds has been investigated. The flaxseed oils were heated at a certain temperature (75, 105, and 135 °C, respectively) for 48 h. The melting curve (from ?75 to 100 °C) of flaxseed oil was determined by differential scanning calorimetry (DSC) at intervals of 4 h. Three DSC parameters of exothermic event and endothermic event, namely, peak temperature (T _peak), enthalpy, and temperature range were determined. The initial flaxseed oil exhibited an exothermic peak, two endothermic peaks, and two endothermic shoulders between ?68 and ?5 °C in the melting profile. Heating temperature had a significant influence on the oxidative deterioration of flaxseed oil. The melting curve and parameters of flaxseed oil were almost not changed when flaxseed oil was heated at 75 °C. However, the endothermic peaks of melting curve decreased dramatically with the increasing of heating time when heating temperature was above 105 °C. There is almost no change of melting heat flow of flaxseed oil when heating time exceeded 32 h at 135 °C. The preliminary results suggest that the DSC melting profile can be used as a fast and direct way to assess the deterioration degree of flaxseed oil.     

Synthesis,characterization, and thermal study of solid-state alkaline earth metal mandelates,except beryllium and radium

Characterization, thermal stability, and thermal decomposition of alkaline earth metal mandelates, M(C₆H₅CH(OH)CO₂)₂, (M = Mg(II), Ca(II), Sr(II), and Ba(II)), were investigated employing simultaneous thermogravimetry and differential thermal analysis or differential scanning calorimetry, (TG–DTA or TG–DSC), infrared spectroscopy (FTIR), complexometry, and TG–DSC coupled to FTIR. All the compounds were obtained in the anhydrous state and the thermal decomposition occurs in three steps. The final residue up to 585 °C (Mg), 720 °C (Ca), and 945 °C (Sr) is the respective oxide MgO, CaO, and SrO. For the barium compound the final residue up to 580 °C is BaCO₃, which is stable until 950 °C and above this temperature the TG curve shows the beginning of the thermal decomposition of the barium carbonate. The results also provide information concerning the thermal behavior and identification of gaseous products evolved during the thermal decomposition of these compounds.     

Relationship between the Cu content and thermal properties of Al–Cu alloys for latent heat energy storage

Current Al alloys still have shortcomings in their volumetric latent heat (LHV), compatibility and high-temperature inoxidizability, which limit their applications in the field of latent heat energy storage (LHES). The performance of aluminum alloys can be improved by the addition of Cu. The effects of the Cu content on the phase change temperature, mass latent heat (LHM), LHV, supercooling degree and microstructure of Al–Cu alloys were first studied by means of power-compensated differential scanning calorimetry, density, composition analysis and metallographic analysis. The measured values of the latent heat of Al–Cu alloys have been compared with the theoretically predicted values. The results show that for Al–Cu alloys with 7.3–52.8% Cu, the melting/freezing temperature is 540–655 °C/510–637 °C; the LHM and the LHV are 290–340 J g^?1 and 877–1224 J cm^?3, respectively; and the degree of supercooling is within 10 °C. The LHM and LHV of Al–Cu alloys decrease with the increase in the Cu content; when the content of Cu is over 16.6%, the difference between the theoretical value of the LHM and the measured average of the Al–Cu alloys is within 5%. The LHES phases in Al–Cu alloys are the α-Al and theta phases. Quantitative relationships of the Cu content and metallurgical microstructure with the LHM and LHV of Al–Cu alloys are established, and both theoretical and empirical equations are obtained for the estimation of the latent heat for Al–Cu alloys.     

Aging of piezoelectricity in poly(vinylidene fluoride)

This report describes isothermal aging of piezoelectricity in poly(vinylidene fluoride) (PVDF) based on long-term heat treatments between 40 and 160°C. The results demonstrate that no piezoelectric decay occurs below about 60°C, that between 60 and 160°C the aging behavior follows logarithmic kinetics, and that aging is linearly dependent on temperature. Both uniaxial and biaxial PVDF show similar trends, but piezoelectric decay is more rapid for uniaxial film. Decay of permanent poling-induced polarization is identified as the likeliest cause of piezoelectric aging, and piezoelectric decay is found to be associated with long-range annealing effects which also produce macroscopic shrinkage of the PVDF film.     

Microstructural properties of sintered Al–Cu–Mg–Sn alloys

A non-commercial Al4Cu0.5Mg alloy has been used for investigating the effects of the elemental Sn additions. Uniaxial die compaction response of the alloys in terms of green density was examined, and the results showed that Sn addition has no effect when compacting conducted under high pressures. In total, 93–95% green density was achieved with an applied pressure of 400 MPa. Thermal events occurring during the sintering of the emerging alloys were studied by using differential scanning calorimetry (DSC). First thermal event on the DSC analysis of the Al4Cu0.5Mg1Sn alloy is the melting of elemental Sn, whereas for Al4Cu0.5Mg alloy, it is the formation of Al–Mg liquid nearly at 450 °C. Also it is clearly seen on the DSC analysis that Sn addition led to an increase in the formation enthalpy of Al–Mg liquid phase. High Sn content and high sintering temperature (620 °C), therefore high liquid-phase content, caused decrease on the mechanical properties due to thick intergranular phases and grain coarsening. Highest transverse rupture strength and hardness values were obtained from Al4Cu0.5Mg0.1Sn alloy sintered at 600 °C and measured as 390 MPa and 73 HB, respectively.     

Thermal behavior of Al-, AlFe- and AlCu-pillared interlayered clays

The purified bentonite parent clay, fraction ≤; 2 mm of montmorillonite type, has been pillared by various polyhydroxy cations, Al, AlFe and AlCu, using conventional pillaring methods. The thermal behavior of PILCs was investigated by combination of X-ray diffraction (XRD), thermal analysis (DTA, TG) and low temperature N2 adsorption/desorption (LTNA). Thermal stability of Al-, AlFe- and AlCu-PILC samples was estimated after isothermal pretreatment in static air on the temperatures 300, 500, 600 and 900°C. Crucial structural changes were not registered up to 600°C, but the fine changes in interlayer surrounding and porous/microporous structure being obvious at lower temperatures, depending on the nature of the second pillaring ion. AlFe-PILC showed higher thermal stability of the texture, the AlCu-PILC having lower values and lower thermal stability concerning both overall texture and micropore surface and volume. Poorer thermal stability of AlCu-PILC sample at higher temperatures was confirmed, the presence of Cu in the system contributing to complete destruction of aluminum silicate structure, by 'extracting' aluminum in stabile spinel form. This revised version was published online in July 2006 with corrections to the Cover Date.     

The melting behaviour of poly(3-hydroxybutyrate) by DSC. Reproducibility study

This work is concerned with the melting behaviour and accuracy of differential scanning calorimeter (DSC) analyses of poly(3-hydroxybutyrate) (PHB), a semi-crystalline thermoplastic polymer completely biodegradable and biocompatible, and obtained from renewable resources. Melting parameters of PHB were determined for the first fusion event applying standard experimental procedures for thermal analysis, using heating rates ranging between 1 °C/min and 20 °C/min. The analyses of DSC energy flow scans showed a complex melting peak that may be resolved into three elementary peaks having different intensities at different melting temperatures. Peak temperatures depend on heating rate, while the total crystallinity detected was independent of the rate. A study of 24 DSC runs showed good temperature reproducibility (±0.5 °C), but poor reproducibility of mass crystallinity (±10%).     

Investigation of structure and thermal stability of surfactant-modified Al-pillared montmorillonite

For combining the properties of organoclays and pillared clays, inorganic–organic clays have attracted much attention in recent years. In this study, Al Keggin cation pillared montmorillonites (Al-Mts) were first prepared and parts of Al-Mts were calcined at different temperatures (C-Al-Mts). The inorganic–organic montmorillonites were synthesized by intercalating Al-Mts and C-Al-Mts with the cationic surfactant, hexadecyltrimethyl ammonium bromide (HDTMAB). The products were characterized by X-ray diffraction, X-ray fluorescence, and simultaneous thermogravimetric analysis. For HDTMAB-modified uncalcined Al Keggin cation pillared montmorillonites (H-Al-Mts), the basal spacing increased with the increment of surfactant loading level, but the Al content of H-Al-Mts decreased simultaneously, indicating that the intercalated surfactant replaced some Al Keggin cations in the interlayer space. However, in the case of C-Al-Mts, the interlayer spaces could not be further expanded after surfactant modification, implying that the neighboring montmorillonite layers were “locked” by the aluminum pillars which were formed by dehydroxylation of Al Keggin cation pillars during thermal treatment. The thermal stability of HDTMAB-modified C-Al-Mts (H-C-Al-Mts) was much better than that of H-Al-Mts. The major mass loss of H-C-Al-Mts occurred at ca. 410 °C, corresponding to decomposition of intercalated surfactant cations. In contrast, H-Al-Mts displayed two mass loss temperatures at ca. 270 and 410 °C, corresponding to the evaporation of surfactant molecules and the decomposition of surfactant cations in the interlayer space, respectively.     

Thermal characterization of solar salts from north of Chile and variations of their properties over time at high temperature

The current study has conducted a wide-ranging characterization, under high-temperature conditions, of a new ternary and quaternary heat transfer fluid, with the addition of Ca(NO₃)₂ and LiNO₃, two of the solar salt additives with a greater potential for being included in these new formulations proposed for the new generation of concentrated solar power (CSP) plants. In this direction, the present research is focused on viscosity and thermal stability since these salts try to increase the work temperature range in CSP plants. Viscosity tests were analyzed each 10 °C from 130 to 300 °C in order to check the variation in this parameter close to their melting points. Isothermal analysis at 450 and 500 °C was also performed through thermal gravimetric (TG) analysis, measuring any resulting loss of mass in the sample at these temperatures. Results were compared with the behavior in binary solar salt. These tests showed a progressive thermal degradation of salts over the time and the maximum temperature for operation in CSP has been corrected regarding the use of ternary and quaternary molten salts.     

Thermal transformations of Cu–Mg (Zn)–Al(Fe) hydrotalcite-like materials into metal oxide systems and their catalytic activity in selective oxidation of ammonia to dinitrogen

Layered double hydroxides (LDHs) containing Mg²⁺, Cu²⁺ or Zn²⁺ cations in the Me^II positions and Al³⁺ and Fe³⁺ in the Me^III positions were synthesized by co-precipitation method. Detailed studies of thermal transformation of obtained LDHs into metal oxide systems were performed using high temperature X-ray diffraction in oxidising and reducing atmosphere, thermogravimetry coupled with mass spectrometry and temperature-programmed reduction. The LDH samples calcined at 600 and 900 °C were tested in the role of catalysts for selective oxidation of ammonia into nitrogen and water vapour. It was shown that all copper congaing samples presented high catalytic activity and additionally, for the Cu–Mg–Al and Cu–Mg–Fe hydrotalcite samples calcined at 600 °C relatively high stability and selectivity to dinitrogen was obtained. An increase in calcination temperature to 900 °C resulted in a decrease of their catalytic activity, possibly due to formation of well-crystallised metal oxide phases which are less catalytically active in the process of selective oxidation of ammonia.     

Influence of high loading of cellulose nanocrystals in polyacrylonitrile composite films

Polyacrylonitrile-co-methacrylic acid (PAN-co-MAA) and cellulose nanocrystal (CNC) composite films were produced with up to 40 wt% CNC loading through the solution casting method. The rheological properties of the solution/suspensions and the structural, optical, thermal, and mechanical properties of the resulting films were investigated. The viscosity of the composite suspensions increased with higher CNC loadings and with longer aging times. PAN-co-MAA/CNC films maintained a similar level of optical transparency even with up to 40 wt% CNC loading. The glass transition temperature (Tg) increased from 92 to 118 °C, and the composites had higher thermal stability below 350 °C compared to both neat PAN-co-MAA and neat CNC. The mechanical properties also increased with higher CNC loadings, elastic modulus increased from 2.2 to 3.7 GPa, tensile strength increased from 75 to 132 MPa, and the storage modulus increased from 3.9 to 10.5 GPa. Using the Kelly and Tyson model the interfacial shear strength between the PAN-co-MAA and CNC was calculated to be 27 MPa.     

Changes of mechanical properties in cold-crystallized syndiotactic polypropylene during aging

Many semicrystalline polymers undergo a process of aging when they are stored at temperatures higher than their glass-transition temperature (T _g). Syndiotactic polypropylene was quenched from the melt to −40 °C, crystallized from the glassy state at 20 or 40 °C and stored at the respective temperature for different aging times up to 7200 h. A significant increase in the tensile modulus and stress at yield and a decrease in strain at yield were observed for both aging temperatures. Differential scanning calorimetry (DSC) scans of aged material showed an endothermic annealing peak 15–30 °C above the previous aging temperature, the maximum temperature and enthalpic content of which increased with aging time. The position and the shape of the melting peak were not affected by aging. Scans of the storage modulus obtained from dynamic mechanical analyser measurements indicated a softening process starting at about 20 °C above the aging temperature and correlating with the annealing peak detected by DSC. Density measurements and wide-angle X-ray scattering investigations revealed that neither the crystallinity increased significantly nor did the crystal structure change. So the observed property changes induced by aging are attributed to microstructural changes within the amorphous phase. Furthermore, it could be shown by annealing experiments carried out at 60 °C, that aging above T _g is, analogous to aging below T _g (physical aging), a thermoreversible process. Received: 18 September 2000 Accepted: 2 January 2001     

Effect of nanosilica on thermal oxidative degradation of SBR

The effect of silica content on thermal oxidative stability of styrene–butadiene rubber (SBR)/silica composites has been studied. Morphologies of silica in SBR with different contents are investigated by scanning electron microscopy, which indicates that silica can well disperse in SBR matrix below the content of 40 %, otherwise aggregates or agglomerates will generate. Composites with around 40 % silica content show excellent mechanical properties and retention ratios after aging at 85 °C for 6 days. The values of activation energy (E _a) of pure SBR and its composites are calculated by Kissinger and Flynn–Wall–Ozawa methods based on thermogravimetric (TG) results, which suggests that composite with about 20 % silica has minimum E _a, and composite with 30–40 % silica has maximum E _a. According to TG curves, it is found that silica can suppress the formation of char leading to decline in stability to some extent. On the other side, silica also has positive effect on improving thermal stability of the matrix as filler. Thus, the SBR/silica composites with silica content of 30–40 % can possess both excellent resistance to thermal oxidative degradation and superior mechanical properties.