Flow Injection Potentiometric Determination of Coke Acidity and Acetic Acid Content in Vinegar Using an Antimony Electrode

Abstract

A flow injection potentiometric procedure is proposed for the determination of acidity of several samples using an antimony/ antimony oxide electrode. The ΔE/pH curve in phosphate buffer solutions in the pH range from 1.58 to 12.00 showed a linear sub-Nernstian behavior with an operational slope S =-42.1mV/pH_c and a conditional standard potential of 264.8mV. This flow potentiometric electrode responds linearly to low acidity variations of dilute acetic acid solutions from 3.16 to 100mM with a slope of 30.1mV/dec and analytical frequency of 23 results/h. Good reproducibility and an average standard deviation of ±0.5% was obtained. The application of this sensor for the determination of coke acidity and acetic acid in vinegar is reported.     

Chromium(III) Ion Selective Electrode Based on Oxalic Acid Bis(Cyclohexylidene Hydrazide)

A poly(vinyl chloride) membrane sensor based on oxalic acid bis (cyclohexylidene hydrazide) as membrane carrier was prepared and investigated as a Cr(III)‐selective electrode. The electrode reveals a Nernstian behavior (slope 19.8±0.4 mV decade^?1) over a wide Cr(III) ion concentration range 1.0×10^?7–1.0×10^?2 mol dm^?3 with a very low limit of detection (i.e., down to 6.3×10^?8 mol dm^?3). The potentiometric response of the sensor is independent of the pH of the test solution in the pH range 1.7–6.5. The electrode possesses advantage of very fast response, relatively long lifetime and especially good selectivity to wide variety of other cations. The sensor was used as an indicator electrode, in the potentiometric titration of chromium ion and in the determination of Cr(III) in waste water and alloy samples.     

All Solid State Nickel(II)‐Selective Potentiometric Sensor Based on an Upper Rim Substituted Calixarene

A new ionophore, i.e. p‐(2‐thiazolazo)calix[4]arene ( I ) has been explored for its selective behavior towards Ni(II) ions. A poly(vinyl chloride) based membrane containing ( I ) as an electroactive material along with sodiumtetraphenylborate (NaTPB), and nitrophenyloctyl ether in the ratio 10 : 100 : 3 : 150 (I:PVC:NaTPB:NPOE) (w/w) was used to fabricate an all solid state nickel(II)‐selective sensor. The developed sensor exhibited a working concentration range of 1.0×10^?6–1.0×10^?1 M, with a Nernstian slope of 28.9±1.0 mV/decade of activity and a response time of 10–15 s. This sensor shows a detection limit of 9.0×10^?7 M. Its potential response remains unaffected of pH in the range 3.0–7.6, and the cell assembly could be used successfully in partially nonaqueous medium (up to 10 % v/v) without any significant change in the slope value or the working concentration range. The sensor worked satisfactorily for about ten weeks and exhibited excellent selectivity over a number of mono‐, bi‐, and tri‐valent cations including alkali, alkaline earth metal, and transition metal ions. It could be used as an indicator electrode for the end point determination in the potentiometric titration of nickel ions against ethylenediaminetetraacetic acid (EDTA) as well as for the determination of nickel ion concentration in real samples.     

Electrochemical determination of iodide by poly(3-aminophenylboronic acid) film electrode at moderately low pH ranges

A new potentiometric sensor for the determination of iodide based on poly(3-aminophenylboronic acid) (PAPBA) film electrode was constructed. Poly(3-Aminophenylboronic acid) films were synthesized electrochemically on platinum electrode by cyclic voltammetry. The effect of film thickness, pH, and preconditioning parameters on the electrode performance were examined. The analytical performance was evaluated and linear calibration graphs were obtained in the concentration range of 10⁻⁶ to 10⁻¹ M iodide ion. The limit of detection was found to be 8 × 10⁻⁷ M. The response time of the sensor was 5 s and its lifetime is about one week. To check the selectivity of the PAPBA film for iodide ion, potential interferences such as Cl⁻, Br⁻, F⁻, CN⁻, IO₃⁻, Ca²⁺, and Mg²⁺ were tested. The PAPBA electrode was also employed as a sensing platform for the determination of iodide ions in commercial table salt.     

Ni(II) selective sensors based on Schiff bases membranes in poly(vinyl chloride)

The two nickel chelates of Schiff bases, 3-hydroxy-N-{2-[(3-hydroxy-N-phenylbutyrimidoyl)-amino]-phenyl}-N′-phenylbutyramidine (M₁) and bis-4-(ethyliminomethyl)naphthalene-1-ol (M₂), have been synthesized and explored as ionophores for preparing PVC-based membrane sensors selective to nickel ion. The influences of membrane compositions on the potentiometric response of the electrodes have been found to substantially improve the performance characteristics. The best performance was obtained with the electrode having a membrane composition (w/w; mg) of (M₁): PVC:NaTPB:CN in the ratio 5:150:5:150. The sensor shows a linear potential response for Ni²⁺ over a wide concentration range 1.6 × 10⁻⁷ to 1.0 × 10⁻² M with Nernstian compliance (30.0 ± 0.2 mV/decade of activity) within pH range 2.5-9.5 and a fast response time of 10 s. The sensor has been found to work satisfactorily in partially non-aqueous media up to 20% (v/v) content of methanol, ethanol, and acetonitrile and could be used for a period of 4 months. The analytical usefulness of the proposed electrode has been evaluated by its application in the determination of nickel in real samples. The practical utility of the membrane electrode has also been observed in the presence of surfactants.     

Development of a Novel Solid‐State pH Sensor Electrode Based on Titanium Oxide Thin Film as an Indicator Electrode in Potentiometric Acid‐Base Titrations in Fused NaNO3 at 350°C

A solid‐state pH sensor was fabricated using a transparent conductive titanium oxide film on a glass substrate. The coating of the glass substrate was achieved by a novel simple chemical vapor deposition (CVD) procedure. The sensor slope was found to increase as the temperature of the solution was increased. The performance of the sensor was investigated in the pH range from 2.2 to 11.19. The E‐pH curve is linear with slope of 0.054 V at 298.15 K. This value is closed to the theoretical value 2.303RT/F (0.059 V at 298.15). The standard potential of this electrode, E°, is computed as 177.58 mV with respect to the SCE as reference electrode. Results obtained by the suggested sensor compares very well with conventional pH electrodes where the square of the correlation coefficient was 0.998. This electrode can be used as an indicator electrode in potentiometric acid‐base titration. This electrode behaves reversibly and responds to the oxide ion concentration in molten NaNO₃. K₂Cr₂O₇ was potentiometrically titrated with Na₂O₂ and K₂CO₃ as titrants in molten NaNO₃ at 350°C, using the above mentioned indicator electrodes. An acidity/basicity scale of the oxyanions was established in molten NaNO₃ at 350°C.     

Novel Liquid Membrane Electrode for Selective Determination of Monohydrogenphosphate

A highly selective and sensitive membrane electrode based on vanadyl salen complex (VS), which responds to monohydrogenphosphate (MHP) ions is described. The response of the sensor is Nernstian over the wide concentration range (1.0×10^?1 ? 5.0×10^?6 M) of MHP. The sensitivity of the electrode is high enough to permit the detection of as little as 0.6 μg/mL of MHP without any significant interference from high levels of other anions. The potentiometric selectivity coefficient data revealed negligible interference from 11 common anions. The electrode has a fast response time (<25 s), good slope stability at pH 8.2 for a period of at least eight weeks. It was successfully applied for the direct determination of monohydrogenphosphate in fertilizer and, as indicator electrode, in potentiometric titration of HPO₄^2? ion with barium chloride.     

pH-sensing properties of PbO<Subscript>2</Subscript> thin film electrodeposited on carbon ceramic electrode

In this paper, a new highly sensitive potentiometric pH electrode is proposed based on the solid-state PbO₂ film electrodeposited on carbon ceramic electrode (CCE). Two different crystal structures of PbO₂, α and β were examined and the similar results were obtained. Moreover, the experimental results obtained for the proposed pH sensor and a conventional glass pH electrode were in good agreement. The electromotive force (emf) signal between the pH-sensitive PbO₂-coated CCE and SCE reference electrode was linear over the pH range of 1.5–12.5. Near-Nernstian slopes of −64.82 and −57.85 mV/pH unit were obtained for α- and β-PbO₂ electrodes, respectively. The interferences of some mono-valence and multi-valence ions on potentiometric response of the sensor were studied. The proposed pH sensor displayed high ion selectivity with respect to K⁺, Na⁺, Ca²⁺, and Li⁺, with log values around −12 and has a working lifetime of about 30 days. Key parameters important for the pH sensor performance, including kind of PbO₂ film, selectivity, response time, stability, and reproducibility, have been characterized. The proposed electrode showed a good efficiency for direct pH-metry after calibration and pH-metric titrations without calibration step. The response time was about 1 s in acidic medium and less than 30 s in alkaline solutions. The pH values of complex matrix samples such as fruit juices measured by the proposed sensor and a conventional glass pH electrode were in good agreement.     

A Novel Al(III)‐Selective Electrochemical Sensor Based on N,N′‐Bis(salicylidene)‐1,2‐phenylenediamine Complexes

A polyvinylchloride membrane sensor based on N,N′‐bis(salecylidene)‐1,2‐phenylenediamine (salophen) as membrane carrier was prepared and investigated as a Al³⁺‐selective electrode. The sensor exhibits a Nernstian response toward Al(III) over a wide concentration range (8.0×10^?7–3.0×10^?2 M), with a detection limit of 6.0×10^?7 M. The potentiometric response of the sensor is independent of the pH of the test solution in the pH range 3.2–4.5. The electrode possesses advantages of very fast response and high selectivity for Al³⁺ in comparison with alkali, alkaline earth and some heavy metal ions. The sensor was used as an indicator electrode, in the potentiometric titration of aluminum ion and in determination of Al³⁺ contents in drug, water and waste water samples.     

Chemically modified electrode based on poly[tetra(4-aminophenyl)porphyrin] as a pH sensor

A chemically modified platinum electrode with coated poly[tetra(4-aminophenyl)porphyrin] has been used as a potentiometric pH sensor. It gives a linear response over the pH range 1.5-13.7 with a slope of 55 mV/pH (at 20 degrees ). The sensor has fair resistance to erosion of hydrofluoric acid and to interference of a coexisting redox couple. The sensor can be used for pH determination and end-point indication for potentiometric titration of hydrofluoric acid with sodium hydroxide. The a.c. impedance of the polymer membrane has also been studied.     

Polymeric membrane and coated graphite electrode based on newly synthesized tetraazamacrocyclic ligand for trace level determination of nickel ion in fruit juices and wine samples

Novel polymeric membrane electrode (PME) and coated graphite electrode (CGE) for nickel ion were prepared based on 2,9-(2-methoxyaniline)₂-4,11-Me₂-[14]-1,4,8,11-tetraene-1,5,8,12-N₄ as a suitable neutral ionophore. The addition of lipophilic anion excluder (NaTPB) and various plasticizers viz o-nitrophenyloctylether (o-NPOE), dioctylphthalate (DOP), dibutylphthalate (DBP), 1-chloronaphthalene (CN) and tri-n-butylphosphate (TBP) have found to improve the performance of the sensors. The best performance was obtained for the membrane sensor having a composition of I:NaTPB:TBP:PVC in the ratio 6:4:100:90 (w/w; mg). The electrodes exhibit Nernstian slopes for Ni²⁺ ions over wide concentration ranges of 4.6 × 10^?7–1.0 × 10^?1 M for PME and 7.7 × 10^?8–1.0 × 10^?1 M for CGE with limits of detection of 2.7 × 10^?7 M for PME and 3.7 × 10^?8 M for CGE. The response time for PME and CGE was found to be 10 and 8 s respectively. The potentiometric responses are independent of the pH of the test solution in the pH range 3.0–8.0. The proposed electrodes revealed good selectivities over a wide variety of other cations including alkali, alkaline earth, transition and heavy metal ions. The coated graphite electrode was used as an indicator electrode in the potentiometric titration of nickel ion with EDTA and in direct determination in different fruit juices and wine samples.     

Determination of vanadium(V) by direct automatic potentiometric titration with EDTA using a chemically modified electrode as a potentiometric sensor

A chemically modified electrode (CME) was prepared and studied as a potentiometric sensor for the end-point detection in the automatic titration of vanadium(V) with EDTA. The CME was constructed with a paste prepared by mixing spectral-grade graphite powder, Nujol oil and N-2-naphthoyl-N-p-tolylhydroxamic acid (NTHA). Buffer systems, pH effects and the concentration range were studied. Interference ions were separated by applying a liquid-liquid extraction procedure.The CME did not require any special conditioning before using. The electrode was constructed with very inexpensive materials and was easily made. It could be continuously used, at least two months without removing the paste.Automatic potentiometric titration curves were obtained for V(V) within 5 × 10⁻⁵ to 2 × 10⁻³ M with acceptable accuracy and precision. The developed method was applied to V(V) determination in alloys for hip prothesis.     

Nickel(II) Ion-Selective Electrode Based on 2,5-Thiophenyl bis(5-tert-Butyl-1,3-Benzoxazole

ABSTRACT

A PVC membrane sensor for Nickel (II) ions based on 2,5-thiophenyl bis(5-tert-butyl-1,3-benzoxazole) as membrane carrier was prepared. The sensor exhibits a Nernstian response for Ni²⁺ ions over a wide concentration range (10^?2–10^?5M). It has a relatively fast response time and can be used for at least 2 months without any considerable divergence in potentials. The nature of the plasticizer, the additive, the concentration of internal solutions in the electrodes and the composition of the membrane were investigated. The proposed membrane electrode revealed very good selectivities for Ni²⁺ over a wide variety of other metal cations and could be used in pH range of 4.0–8.0. It was successfully applied for the direct determination of Ni²⁺ in solution and as an indicator electrode in potentiometric titration of nickel ion in both water and 85% acetonitrile solutions.     

Solid-state Electrochemical Sensor Based on a Cross-linked Copper(II)-doped Copolymer and Carbon Nanotube Material for Selective and Sensitive Detection of Monohydrogen Phosphate

A novel solid-state electrochemical sensor based on a newly synthesized cross-linked copper(II) doped-copolymer and carbon nanotube material was developed for the direct determination of monohydrogen phosphate ions (HPO₄²⁻). The synthesized copolymers were characterized by FTIR, XPS, TG/DTG-DTA and SEM techniques. The sensor had a Nernstian slope:-30.7±0.4 mV/decade, linear concentrations range: 1.0×10⁻⁶ - 1.0×10⁻¹ M, detection limit: 6.5×10⁻⁷ M, response time: 4 s and life time: 17 weeks. The sensor displayed constant potentials in the pH range 7.0-9.5. The sensor was successfully used as an indicator electrode in potentiometric titration and the direct determination of HPO₄ ²⁻ in water samples.     

Preparation of a solid-state ion-selective electrode based on polypyrrole conducting polymer for magnesium ion

In this study, a potentiometric sensor based on a pencil graphite electrode (PGE) coated with polypyrrole doped with Titan yellow dye (PPy/TY) was prepared for potentiometric determination of magnesium ion in aqueous solutions. The structural characteristics of magnesium sensor electrode (PGE/PPy/TYMg) were studied using scanning electron microscopy and Fourier transform infrared along with energy-dispersive spectroscopy. Under the optimal conditions, the electrode reveals a good Nernstian behavior with slope of 28.27 ± 0.40 mV per decade over the concentration range of 1.0 × 10^?5–5.0 × 10^?2 M and a detection limit of 6.28 × 10^?6 M. The potentiometric response of fabricated electrode toward magnesium ion was found to be independent of the pH of the test solution in the pH range of 4.5–8.0. The electrode showed fast response time (<10 s) and good shelf lifetime (>2 months). The prepared magnesium sensor electrode can also be used as an indicator electrode in potentiometric titration of Mg²⁺ with EDTA with distinguished end point. The electrode revealed good selectivity with respect to many cations including alkali, alkaline earth, transition and heavy metal ions. The introduced magnesium electrode was used for measurement of Mg²⁺ ion in real samples without any serious interferences from other ions.     

Construction of a new solid-state U(VI) ion-selective electrode based on polypyrrole conducting polymer

In this study, a potentiometric sensor based on a pencil graphite electrode (PGE) coated with polypyrrole doped with uranyl zinc acetate (termed PGE/PPy/U) have been prepared for potentiometric determination of uranyl in aqueous solutions. Electropolymerization reaction for preparing of U(VI) sensor electrode was carried via applying a constant current of 1.0 mA on PGA working electrode in a solution containing 8.0 mM pyrrole and 0.8 mM ZnUO₂(CH₃COO)₄ salt. The constructed electrode displayed a linear and near Nernstian response (22.60 ± 0.40 mV/decade) to U(VI) ions in the concentration range of 1.0 × 10^?6–1.0 × 10^?2 M. A detection limit of 6.30 × 10^?7 M and a fast response time (≤12 s) was observed during measurements. The working pH range of the electrode was 4.0–8.0 and lifetime of the sensor was at least 60 days. The electrode revealed good selectivity with respect to many cations including alkali, alkaline earth, transition and heavy metal ions. The introduced uranyl electrode was used for measurement of U(VI) ion in real samples without any serious inferences from other ions.     

Lead(II) Potentiometric Sensor Based on 1,4,8,11‐Tetrathiacyclotetradecane Neutral Carrier and Lipophilic Additives

A potentiometric sensor for lead(II) ions based on the use of 1,4,8,11‐tetrathiacyclotetradecane (TTCTD) as a neutral ionophore and potassium tetrakis‐(p‐chlorophenyl)borate as a lipophilic additive in plasticized PVC membranes is developed. The sensor exhibits linear potentiometric response towards lead(II) ions over the concentration range of 1.0×10^?5–1.0×10^?2 mol L^?1 with a Nernstian slope of 29.9 mV decade^?1 and a lower limit of detection of 2.2×10^?6 mol L^?1 Pb(II) ions over the pH range of 3–6.5. Sensor membrane without a lipophilic additive displays poor response. The sensor shows high selectivity for Pb(II) over a wide variety of alkali, alkaline earth and transition metal ions. The sensor shows long life span, high reproducibility, fast response and long term stability. Validation of the method by measuring the lower limit of detection, lower limit of linear range, accuracy, precision and sensitivity reveals good performance characteristics of the proposed sensor. The developed sensor is successfully applied to direct determination of lead(II) in real samples. The sensor is also used as an indicator electrode for the potentiometric titration of Pb(II) with EDTA and potassium chromate. The results obtained agree fairly well with data obtained by AAS.     

Highly Sensitive Membrane Electrode Based on a Copper(II)-bis(N-4-Methylphenyl-Salicyldenaminato) Complex for the Determination of Chromate

A highly sensitive polyvinyl chloride (PVC) membrane electrode, based on copper(II)-bis(N-4-methylphenyl-salicyldenaminato) complex, (CuL₂), as a carrier was reported for the determination of chromate ion. The influence of membrane composition, pH, and possible interfering anions on the response of the ion selective electrode was investigated. The sensor exhibited a Nernstian slope of 29.7 mV per decade when the chromate concentration was varied between 2.0 × 10^?7–1.50 × 10^?2 M in a wide pH range (6.0 to 9.0). The detection limit of the ion selective electrode was 9.2 × 10^?8 M. The proposed sensor was used for at least 4 months without any considerable divergence in potential. It was applied as indicator electrode in potentiometric titration of chromate ion with Pb²⁺ and Tl⁺.     

Solid-contact potentiometric sensor for ascorbic acid based on cobalt phthalocyanine nanoparticles as ionophore

A novel solid-contact potentiometric sensor for ascorbic acid based on cobalt phthalocyanine nanoparticles (NanoCoPc) as ionophore was fabricated without any need of auxiliary materials (such as membrane matrix, plasticizer, and other additives). The electrode was prepared by simple drop-coating NanoCoPc colloid on the surface of a glassy carbon electrode. A smooth, bright and blue thin film was strongly attached on the surface of the glassy carbon electrode. The electrode showed high selectivity for ascorbic acid, as compared with many common anions. The influences of the amount of NanoCoPc at the electrode surface and pH on the response characteristics of the electrode were investigated. To overcome the instability of the formal potential of the coated wire electrode, a novel electrochemical pretreatment method was proposed for the potentiometric sensor based on redox mechanism. This resulting sensor demonstrates potentiometric response over a wide linear range of ascorbic acid concentration (5.5 × 10⁻⁷ to 5.5 × 10⁻² M) with a fast response (<15 s), lower detection limit (ca. 1.0 × 10⁻⁷ M), and a long-term stability. Furthermore, microsensors based on different conductors (carbon fiber and Cu wire) were also successfully fabricated for the determination of practical samples.     

Potentiometric determination of mercury(II) and thiourea in strong acid solution using an ion-selective electrode with AgI-based membrane hydrophobised by PTFE

Summary The potentiometric determination of mercury(II) and thiourea (TU) in strong acid solution (pH 0–1) by using an all-solid-state ion-selective electrode with (Ag₂S 25%, AgI 25% and PTFE 50% m/m)-membrane is described. The linear response, 43 mV(pHg)^–1 and 80 mV(pTU)^–1, has been obtained in the concentration range from 10^–2 to under 10^–5 mol/l. By direct potentiometry at pH 0 mercury(II) can be determined in the presence of up to 10^–3 mol/l of iron(III). The change in potential in the tested concentration range of thiourea indicates the formation of Ag(TU) _1.4 ⁺ at the exposed surface of the membrane. This stoichiometry is in good agreement with that calculated from the average Ag/TU ratio in the potentiometric titration. The investigated electrode can be used as a good sensor for mercury(II) and thiourea in strong acid media and a wide variety of practical analytical systems.