Rapid spectrophotometric determination of ruthenium(III) with prochlorperazine maleate

A rapid, simple spectrophotometric method for the determination of μg amounts of ruthenium, based on the formation of a pink complex between the metal and prochlorperazine maleate (PCPM) in sulphuric or hydrochloric acid solution, is described. The complex has an absorption maximum at 530 nm and its molar absorptivity is 6.733·10³ l mol^?1 cm^?1. The sensitivity is 0.0151 μg Ru cm^?2 for log I_o/I = 0.001. Beer's law is valid over the range 0.2–10 μg Ru ml^?1 ; the optimal range for spectrophotometric determination is 0.8–8.0 μg Ru ml^?1. Job's method of continuous variation, the mole ratio method and the slope ratio method indicate a 1:1 composition for the complex. The effects of acidity, time, temperature, order of addition of reagents, reagent concentration, and the interferences from various ions are reported.     

Use of diode-array detectors for the simultaneous spectrophotometric determination of calcium and magnesium by flow injection

A method for the simultaneous flow injection spectrophotometric determination of calcium and magnesium with Arsenazo III based on the use of diode-array detector and merging zones is described. The method is applicable to the resolution of mixtures in which the chromogenic reagent has a high absorbance and its spectrum strongly overlaps those of its complexes. In resolving the mixtures, the excess reagent is considered as another component. Quantitation is based on the normal absorbance and first-derivative absorbance spectra. The method is applied to 0.2–1.5 μg ml^?1 Ca and 0.1–1.0 μg ml^?1 Mg. The analysis rate is 50 h^?1.     

Spectrophotometric Determination of Uranium(VI) with Chlorophosphonazo-mN by Flow Injection Analysis

Abstract

A sensitive and selective spectrophotometric flow injection analysis (FIA) method with chlorophosphonazo-mN has been developed for the determination of uranium(VI) in standard ore samples. Most of interfering ions are effectively eliminated by the masking reagent of diethylenetriaminepentaacetic acid (DTPA). In the U(VI)-chlorophosphonazo-mN system, the maximum absorption wavelength is at 680 nm and Beer's law is obeyed in the range of 1 to 15 μg ml^?1. The correlation coefficient of the calibration curve is 0.9998, the sampling frenquency is 60 h^?1, and the detection limit for uranium(VI) is 0.5 μg ml^?1. The composition of the U(VI)-chlorophosphonazo-nN complex was established to be 1:2 by flow-through spectrophotometric and conventional molar ratios methods.     

Spectrophotometric study of the reaction of bismuth with bromopyrogallol red in the presence of tensides: The determination of bismuth and EDTA

The formation of the complex between bismuth and bromopyrogallol red in the presence of cationogenic tensides CPB or Septonex was studied. Optimal conditions for this reaction were found and a new spectrophotometric method was developed for determining bismuth in the concentration range 0.2–5.5 μg · ml^?1. On the basis of the reaction of Bi with EDTA, a new method was developed for the indirect determination of EDTA in the concentration range 0.2–6.0 μg · ml^?1.     

New Spectrophotometric Method for the Determination of Titanium in Soil and Standard Geochemical Samples

Abstract

In the present communication a simple and rapid spectrophotometric method for the determination of titanium is described. The method is based on the reaction of Ti(IV) with a newly synthesized reagent, 6-(4-nitrophenylazo)-3,4,5-trihydroxy benzoic acid (NATHB), in ethanol medium at pH 3.2 to 4.2. The complex exhibits an absorption maximum at 495 nm and Beer's law is valid over the range of 0.04 – 1.00 μg.ml^?1 Ti. The molar absorptivity is 3.48 × 10⁴ dm³.mole^?1. cm^?1. Most of the foreign metal ions and anions do not produce any colorations with NATHB at selected conditions. Based on these results, a simple and direct spectrophotometric method with high selectivity and sensitivity was proposed. The method has been successfully applied for the determination of titanium in 5 soil and 3 standard geochemical samples.     

Spectrophotometric determination of vanadium using variamine blue and its application to synthetic, environmental and biological samples

A simple, rapid and accurate spectrophotometric method is described for the determination of trace amounts of vanadium using variamine blue (VB) as a chromogenic reagent. The method is based on the oxidation of variamine blue to form a violetcolored species on reaction with vanadium(V), having an absorption maximum at 570 nm. Beer’s law is obeyed in the range of 0.1–2.0 μg ml^?1. The molar absorptivity and Sandell’s sensitivity were found to be 1.65 × 10⁴ l mol^?1 cm^?1 and 0.003 μg cm^?2, respectively. Optimum reaction conditions were evaluated in order to delimit the linear range. The effect of interfering ions on the determination is described. The proposed method has been successfully applied to the determination of vanadium in steel, pharmaceutical, environmental, and biological samples.     

Utility of p-chloranilic Acid and 2,3 Dichloro-5,6-dicyano p-Benzoquinone (DDQ) for the Spectrophotometric Determination of Triamterene

Abstract

Two simple and sensitive spectrophotometric procedures are suggested for analysis of triamterene. The first procedure is based on the reaction of triamterene with p-chloranilic acid (p-CA) in methylene chloride to form a highly stable coloured product, exhibiting maximum absorbance at λ 530 nm. Beer's law is obeyed in the range of 40–220 μg.ml^?1 with a mean percentage accuracy of 99.98 ± 0.446. Limit of determination is 20 μg.ml^?1. In the second procedure, the drug is determined via charge transfer complex formation with 2,3 dichloro-5,6-dicyano p-benzoquinone (DDQ) using methylene chloride as a solvent. Here the reaction product has two well defined maxima at 460 nm and 530 nm where each has been utilized for quantitative determination. Beer's law is obeyed in concentration ranges of 25–125 μg.ml^?1 and 25–150 μg.ml^?1 with mean percentage accuracies of 99.92 ± 0.449 and 100.00 ± 0.511 for both maxima. 460 and 530 nm. respectively. Limit of determination is 12.5 μg.ml^?1 at both maxima. Optimum conditions for each procedure have been studied and the stoichiometry of both reactions was ascertained using Job's method of continuous variation. The validity of the suggested procedures was assessed by applying the standard addition technique using the drug capsules. Both procedures are statistically analyzed as compared with BP method for analysis of triamterene (non aqueous titration) revealing good accuracy and precision as indicated by t and F tests.     

Spectrophotometric and First Derivative Spectrophotometric Determination of Magnesium with 1-Hydroxy-2-Carboxyanthraquinone

Abstract

1-Hydroxy-2-carboxyanthraquinone reacts with magnesium in ethanol-water mixtures to form a red complex having an absorption maximum at 490 nm in alkaline medium. A detailed study of the characteristics of this complex has been carried out and a spectrophotometric method for the determination of magnesium at the 0.4–4.0 μg ml^?1 level is proposed. The method has been sensitized by employing first derivative spectrophotometry. By the use of the derivative approach magnesium can be determined between 0.08–0.40 μg ml^?1. Statistical analysis of the results is also described.     

Determination of 1,4-thienodiazepines by liquid chromatography with spectrophotometric,amperometric and coulometric detection

Spectrophotometric, amperometric and coulometric methods of detection for the liquid chromatographic determination of four 1,4-thienodiazepines were compared. The effects of several experimental parameters on the separation and sensitivity of the method was evaluated. A mobile phase consisting of methanol—water (60 + 40) and containing ammonium acetate buffer (pH 7) appeared to be optimal when using a 4-μm Novapak ODS column. The amperometric and coulometric detectors, equipped with glassy carbon electrodes, were operated at +1.05 V vs. Ag/AgCl. The limits of detection obtained ranged from 0.05 to 0.2 μg ml^?1 for spectrophotometric detection, from 0.05 to 0.2 μg ml^?1 for amperometric detection and from 0.006 to 0.02 μg ml^?1 for coulometric detection.     

Automated stopped-flow system in pharmaceutical and clinical analysis : Kinetic determination of acetaminophen in formulations and serum by using the iron(II)—2,4,6-tris(2-pyridyl)-s-triazine

The development of automated stopped-flow spectrophotometric systems, their potential in automated routine determinations using kinetic and fast equilibrium techniques and several examples of applications are briefly reviewed. The use of a compact, inexpensive laboratory-made stopped-flow system for the measurement of reaction rates and a fast equilibrium method for the determination of acetaminophen in formulations and serum are described. The reaction-rate method is based on monitoring the oxidation of acetaminophen by iron(III) in the presence of the chelating agent 2,4,6-tris(2-pyridyl)-s-triazine to form a highly absorbing complex of iron(II). The calibration graph is linear in the range 20–200 μg ml^?1, with a precision of 0.8–2.6%, a detection limit of 5.5 μg ml^?1 and a measurement throughput of 120 per hour. Common excipients do not interfere and the analysis of commercial formulations gave results similar to those of a reference method. The optimization of the experimental conditions was done by a kinetic study of the reaction and some kinetic parameters are given.The method for the determination of acetaminophen in serum is based on a rapid measurement of the absorbance of the reaction mixture after a delay time of 15 s in the presence of chlorpromazine, which catalyses the reaction. Acetaminophen is isolated by extraction with ethyl acetate and the calibration graph is linear in the range 0.5–6 μg ml^?1 with a detection limit of 0.04 μg ml^?1 and a precision of 1.5%. The proposed method showed a decreased interference from drugs that also react with iron(III).     

Some Arylidene-2-Pyridylhydrazone Derivatives as Reagents for Spectrophotometric Determination of Palladium (II)

Abstract

A method for spectrophotometric determination of palladium by complexation with Arylidene-2-pyridylhydrazone derivatives in 50% (V/V) ethanolic solution are described-Pd(II) forms a 1:1 complex with the reagents. Beer's law is obeyed over the range 0.2-6.5 μg ml^?1. The effect of pH, effect of excess reagent, stability of complexes as well as the tolerance amount of many metal ions have been reported. The method is applied, with fair accuracy, to the determination of pd(II) in synthetic solutions.     

Determination of Molybdenum in Human Urine by Spectrophotometric Method using Thiazolylazo Compounds as Chromogenic Reagents

ABSTRACT

Four azo compounds based on diazotization of 2-aminobenzothiazole have been synthesized and characterized by elemental analysis as well as different spectroscopic techniques. The potentiality of the prepared compounds as new chromogenic reagents for the spectrophotometric determination of Mo⁶⁺ was studied by extensive investigation of optimum conditions favouring the formation of the coloured complexes. Beers law is obeyed in the concentration range 0.2-8.5 μg ml^?1 whereas Ringbom optimum concentration range was 0.8-7.5 μg ml^?1. The detection limit was 0.05 μg ml^?1. The molar absorptivity and Sandell sensitivity of the formed complexes are calculated. The effect of interfering ions on the determination of Mo⁶⁺ was investigated. The relative standard deviations for six replicate determinations of 5.0 μg ml^?1 of Mo⁶⁺ are 1.23, 1.47, 1.05 and 1.38 % using reagents I, II, III and IV, respectively. The proposed method has been applied to investigate the amount of Mo⁶⁺ in human urine samples. The molybdenum levels found between 0.5-2.1 μg/100 ml.     

Extraction-spectrophotometric determination of mercury with 1,2,4,6-tetraphenylpyridinium perchlorate

The characteristics of 1,2,4,6-tetraphenylpyridinium perchlorate (TPPP) as a reagent for the formation of ion-pair complexes with metal-bromide anions, and its application to the spectrophotometric determination of mercury are described. This reagent forms a 1:1 complex with bromomercurate(II) ions that is slightly soluble in water and can be extracted with isopentyl acetate. The optimum conditions are about 0.5 M sulphuric acid and 0.03 M potassium bromide. Mercury can be determined at 310 nm in the range 0.04–0.5 μg ml^?1; the apparent molar absorptivity is 2.63 × 10⁴ l mol^?1 cm^?1, and the conditional stability constant is log K - 4.7 ± 0.1 at 20°C. The main interferences are easily removed. Mercury can be determined in sphalerites and zinc amalgams.     

Simultaneous First-Derivative Spectrophotometric Determination of Nickel and Manganese Complexes with 2-(2-Pyridylmethyleneamino)phenol

Abstract

A method is proposed for the simultaneous determination of nickel and manganese by first-derivative spectrophotometry based on their reactions with 2-(2-pyridylmethyleneamino)phenol (PMAP) Schiff base. The method allows the determination of Ni and Mn in the concentration range 0.3–3.0 μg ml^?1 in mixtures with their ten-fold concentration ratio. The method has been applied for Ni and Mn determination in bronzes. To optimize the experimental conditions for spectrophotometric determination of Mn with PMAP stability constants at different pH values have been determined. A critical evaluation of the proposed method was performed by statistical analysis of the experimental data.     

Spectrophotometric Determination of Acebutolol Hydrochloride and Nicoumalone with Metol and Potassium Permanganate

Abstract

A spectrophotometric method is described for the determination of Nicoumalone and Acebutolol hydrochloride based on the formation of molecular complex with the reduction product of Nicoumalone or hydrolysis product of Acebutolol hydrochloride and p-N-methyl benzoguinone monoimine [formed in situ from met01 (p-N-methylaminophenol sulfate) and potassium permanganate, PMBQMI] at pH 3.3. Quantitative measurements were made at the maximum absorption of 525 nm. Beer's law is obeyed in the range of 5–50 μg ml^?1 and 5–60 μg ml^?1 for Nicoumalone and Acebutolol hydrochloride respectively. The proposed method is comparable with the reference method when applied to pharmaceutical preparations, and tablets, An average percentage recovery of 99.5 ± 0.8 was obtained.     

Spectrophotometric determination of osmium with phthalimide dithiosemicarbazone by means of complex formation and catalytic reactions

Phthalimide dithiosemicarbazone forms a 1:1 complex with osmium at pH 3.3–4.5 (?₄₅₀ = 1.3 · 10⁴ l mol^?1 cm^?1 ) which is applied to the photometric determination of osmium; Beer's law is obeyed for the range 1–12 μg Os ml^?1. The oxidation of the reagent with cerium(IV) is catalyzed by osmium(VIII), and this reaction allows a more sensitive procedure for the determination of osmium; the calibration curve is linear over the range 0.05–0.4 μg Os ml^?1. The interferences in both procedures are described.     

Integrated Retention/Spectrophotometric Detection Method for the Determination of Formaldehyde

Abstract

An integrated-sensor method for the determination of formaldehyde based on retention of the reaction product of the analyte with p-rosaniline and sulfite in a flow-cell packed with Dowex 1-X-8 anion exchange resin was developed. The method has a good selectivity with a detection limit of 0.3 μg ml^?1 (1 ml sample) or 75 ng ml^?1 (2 ml sample), and a linear range between 1–30 μg ml^?1. The relative standard deviations (n = 11) were 2.8 and 1.3% for 2 and 20 μg ml^?1 formaldehyde, respectively. Depending on the working conditions, the sampling frenquency ranged between 10 and 18 h^?1. The method was applied to the determination of formaldehyde in well water.     

Solid phase extraction of zirconium as arsenazo(III) complex on agar and spectrophotometric determination

A new solid phase extraction method for the separation and determination of zirconium using agar as an adsorbent is described. The method is based on the adsorption of zirconium as arsenazo(III) complex on agar in a mini-column, elution with sulfuric acid-acetone mixture and determination by spectrophotometry. The effect of different parameters such as pH, concentration of the reagent, eluting reagent, and volume of the sample, amount of the adsorbent and interfering ions was investigated. The calibration graph was linear in the range of 5?C300 ng ml^?1 of zirconium under optimum conditions. The limit of detection based on 3S_b was 1.3 ng ml^?1 and the relative standard deviation (R.S.D) for ten replicate measurements of 15 and 200 ng ml^?1 of zirconium was 3.7 and 1.8%, respectively. The method was applied to the determination of zirconium in water and soil samples.     

Flow-injection spectrophotometric determination of ascorbic acid by reduction of vanadotungstophosphoric acid

Ascorbic acid may be determined spectrophotometrically at 360 nm based on reduction of vanadotungstophosphoric acid using flow-injection analysis. The carrier stream was distilled water and the reagent streams were buffer solution (pH 3.0), 1.735 × 10^?3 M dodecatungstophosphoric acid and 1.735 × 10^?3 M sodium vanadate. The injection rate was 80 h^?1. The calibration graph was linear up to 80 μg ml^?1 ascorbic acid and the relative standard deviation for the determination of 20 μg ml^?1 ascorbic acid was 1.5% (n=10). The detection limit was 1.0 μg ml^?1 ascorbic acid, based on an injection volume of 250 μl. The system was applied to the determination of ascorbic acid in vitamin C tablets.     

Simultaneous determination of ammonia and urea with an asymmetric merging zones/flow-injection configuration

A method is proposed for the simultaneous determination of urea and ammonia using a reagent-injection configuration that includes a dual injection valve (for insertion of Nessler's reagent and for accommodating the enzyme reactor). The resolution of the two peaks obtained on each injection allows the determination of both analytes in mixtures. The determination range is 1–5 μg ml^?1 for ammonia and 1–6 μg ml^?1 for urea, with relative standard deviations of 1.13% and 2.31% for ammonia (first and second peaks) and 1.86% for urea.