Synthesis and characterisation of the anion-ordered tellurides MGeTe (M = Co,Rh)

The synthesis and structural characterisation, carried out using a combination of single-crystal and powder X-ray diffraction, of the materials MGeTe (M = Co, Rh) are described. These phases adopt an ordered α-NiAs₂ structure, which can be considered intermediate between those of pyrite and marcasite. Electrical resistivity and Seebeck coefficient measurements, carried out over the temperature range 77 ≤ T/K ≤ 325, indicate that these materials are n-type semiconductors.     

Towards surface acid–base property of the carboxylic multi-walled carbon nanotubes by zero current potentiometry

The surface acid–base property of carboxylic multi-walled carbon nanotubes (MWNTs) is investigated by zero current potentiometry with a new electrochemical measurement system. The pH dependent interface potential variation at the interface of carboxylic MWNTs/solution is investigated by measuring zero current potential E_zcp. In the pH range of 1–11, the pH response of carboxylic MWNTs exhibits two linear relationships according to the following equations: E_zcp = 0.791–0.0535 pH (pH 1–5.1) and E_zcp = 0.643–0.0241 pH (pH 5.1–11), respectively. The intersection at pH 5.1 of two regions indicates the surface pK_a value of carboxylic group terminated MWNTs.     

The electrode responses of a tungsten bronze electrode differ in potentiometry and voltammetry and give access to the individual contributions of electron and proton transfer

A tungsten wire covered with Na_0.75WO₃ acts in potentiometry as a reversible pH electrode having a pH dependent open-circuit potential E_ocp with nernstian slope. The mid-peak potential E_mp of cyclic voltammograms also depends on pH. At low pH (e.g., pH 2) and slow scan rates (e.g., 2 mV s^–1) the voltammetric response is almost completely reversible. At higher pH and faster scan rates, the voltammetric systems exhibit features of increasing irreversibility. Under the conditions of reversibility, the E_ocp and E_mp differ significantly. E_ocp is determined by the proton transfer at the electrode surface; whereas E_mp is determined by the electron transfer equilibrium tungsten(VI)/tungsten(V) and the proton transfer at the electrode surface. The difference between E_ocp and E_mp provides the individual thermodynamic contributions of electron and proton transfer to the overall pH dependent redox electrode. This is the first time that both contributions can be separated for an insertion electrochemical system (thin surface layer). It is also shown for the first time that the mechanism of an ion-sensitive electrode can differ in potentiometry and voltammetry.     

Crystal structure and phase transitions of sodium potassium niobate perovskites

This paper presents the crystal structure and the phase transitions of K_xNa_1?xNbO₃ (0.4 ≤ x ≤ 0.6). X-ray diffraction measurements were used to follow the change of the unit-cell parameters and the symmetry in the temperature range 100–800 K. At room temperature all the compositions exhibited a monoclinic metric of the unit cell with a small monoclinic distortion (90.32° ≤ β ≤ 90.34°). No major change of symmetry was evidenced in the investigated compositional range, which should be characteristic of the morphotropic phase-boundary region. With increasing temperature, the samples underwent first-order monoclinic–tetragonal and tetragonal–cubic transitions. Only the potassium-rich phases were rhombohedral at 100 K.     

Solubility of boldo leaf antioxidant components (Boldine) in high-pressure carbon dioxide

This work contributes to the development of an enrichment process for antioxidant compounds in aqueous alcoholic extracts of boldo (Peumus boldus M.) leaves by using high-pressure CO₂ as the solvent. Specifically we measured the high-pressure solubility (y₂, molar fraction) of a selected bioactive compound in boldo leaves (boldine) in CO₂ as a function of system temperature (298 K ≤ T ≤ 333 K) and pressure (8 MPa ≤ P ≤ 40 MPa). Experimental data was correlated by using a density-based model which is valid for solvent densities >607 kg/m³. Predicted solubility values are low (4 × 10⁻⁷ ≤ y₂ ≤ 6 × 10⁻⁵) but comparable with those of nitrogen-containing organic compounds with similar molecular weight (327.4 Da) and solubility parameter (28.3 MPa^0.5 at 313 K) as boldine.     

Bioelectrocatalytic formate oxidation and carbon dioxide reduction at high current density and low overpotential with tungsten-containing formate dehydrogenase and mediators

We show a great possibility of mediated enzymatic bioelectrocatalysis in the formate oxidation and the carbon dioxide (CO₂) reduction at high current densities and low overpotentials. Tungsten-containing formate dehydrogenase (FoDH1) from Methylobacterium extorquens AM1 was used as a catalyst and immobilized on a Ketjen Black-modified electrode. For the formate oxidation, a high limiting current density (j_lim) of ca. 24 mA cm^− 2 was realized with a half wave potential (E_1/2) of only 0.12 V more positive than the formal potential of the formate/CO₂ couple (E°′_CO2) at 30 °C in the presence of methyl viologen (MV^2 +) as a mediator, and j_lim reached ca. 145 mA cm^− 2 at 60 °C. Even when a viologen-functionalized polymer was co-immobilized with FoDH1 on the porous electrode, j_lim of ca. 30 mA cm^− 2 was attained at 60 °C with E_1/2 = E°′_CO2 + 0.13 V. On the other hand, the CO₂ reduction was also realized with j_lim ≈ 15 mA cm^− 2 and E_1/2 = E°′_CO2 − 0.04 V at pH 6.6 and 60 °C in the presence of MV^2 +.     

Cyanamide-derived non-precious metal catalyst for oxygen reduction

Cyanamide was used in the preparation series of metal–nitrogen–carbon (M–N–C) oxygen reduction catalysts. The best catalyst, treated at 1050 °C, shows good performance versus previously reported non-precious metal catalysts with an OCV ~ 1.0 V and a current density of 105 mA/cm² (iR-corrected) at 0.80 V in H₂/O₂ fuel cell testing (catalyst loading: 4 mg cm^? 2). Although nitrogen content has been previously correlated positively with ORR activity, no such trend is observed here for any nitrogen type. The combined effects of nitrogen and sulfur incorporation into the carbon may account for the high activity of the 1050 °C catalyst.     

A topographic view of the Pt(1 1 1) surface at the electrochemical interface in the presence of carbon monoxide

In this communication we present topographic images of the Pt(1 1 1) surface in CO saturated 0.1 M HClO₄, obtained by scanning tunneling microscopy.The topography presents two different structures, depending on the CO adsorption potential (E_ad = 0.15 V or E_ad = 0.5 V vs RHE). For adsorption at 0.15 V the system presents a heterogeneous appearance, which totally covers the surface and impedes the observation of steps on the substrate surface. When CO is adsorbed at 0.5 V large clusters forming chains along the steps are observed. These aggregates can be, tentatively, correlated with the H-bonded water structure suggested earlier on the basis of FTIR spectroscopy. The clusters have inhibitory effects on CO oxidation.     

Controllable thermal expansion and phase transition in Yb2−xCrxMo3O12

The thermal expansion and phase transition of solid solutions Yb_2?xCr_xMo₃O₁₂ have been investigated by X-ray powder diffraction and differential thermal analysis. The XRD patterns and the results of Rietveld refinement of Yb_2?xCr_xMo₃O₁₂ indicate that the solid solution limit was in the composition range of 0.0 ≤ x ≤ 0.4 and 1.7 ≤ x ≤ 2.0. Yb_2?xCr_xMo₃O₁₂ (0.0 ≤ x ≤ 0.4) has an orthorhombic structure and exhibits negative thermal expansion between 200 °C and 800 °C. Yb_2?xCr_xMo₃O₁₂ (1.7 ≤ x ≤ 2.0) crystallizes in monoclinic below the phase transition and above, transforms to orthorhombic. Both monoclinic and orthorhombic compounds Yb_2?xCr_xMo₃O₁₂ (1.7 ≤ x ≤ 2.0) present positive thermal expansion. Orthorhombic Yb_2?xCr_xMo₃O₁₂ exhibit anisotropic thermal expansion with the contraction of a and c axes, and the linear thermal expansion coefficients range from negative to positive with increasing chromium content. Partial substitution of Yb³⁺ for Cr³⁺ exhibits depressed monoclinic to orthorhombic phase transition.     

Investigation of the isothermal (vapour + liquid) equilibria of aqueous 2-amino-2-methyl-1-propanol (AMP), N-benzylethanolamine,or 3-dimethylamino-1-propanol solutions at several temperatures

The vapour pressures of (2-amino-2-methyl-1-propanol (AMP) + water), (N-benzylethanolamine + water), or (3-dimethylamino-1-propanol + water) binary mixtures, and of pure AMP and 3-dimethylamino-1-propanol components were measured by means of two static devices at temperatures between 283 K and 363 K. The data were correlated with the Antoine equation. From these data, excess Gibbs functions (G^E) were calculated for several constant temperatures and fitted to a fourth-order Redlich–Kister equation using the Barker’s method. The {2-amino-2-methyl-1-propanol (AMP) + water} binary mixture exhibits negative deviations in G^E (at T < 353.15 K) and a sinusoidal shape for G^E for the higher temperatures over the whole composition range. For the aqueous N-benzylethanolamine solution, a S shape is observed for the G^E for all investigated temperatures over the whole composition range. The (3-dimethylamino-1-propanol + water) binary mixture exhibits negative deviations in G^E (at T < 293.15 K), positive deviations in G^E (for 293.15 K < T < 353.15 K) and a sinusoidal shape for G^E for the higher temperatures over the whole composition range.     

Li(4−x)/3Ti(5−2x)/3CrxO4 (0 ≤ x ≤ 0.9) spinels: New negatives for lithium batteries

Members of the spinel solid solution between Li_4/3Ti_5/3O₄ and LiCrTiO₄, i.e., Li_(4−x)/3Ti_(5−2x)/3Cr_xO₄ (0 ≤ x ≤ 0.9), have been investigated as possible negative electrodes for future lithium-ion batteries. Electrochemical behaviour have been studied over the potential range 1–3.5 V vs Li⁺/Li. Results are promising with anodic capacities between 129 and 163 mA h/g with a flat operating voltage at about 1.5 V, which is attributed to the pair Ti⁴⁺/Ti³⁺. The inclusion of Cr³⁺ in the spinel structure enhances the specific capacity. In-situ X-ray diffraction experiments confirm that the reaction proceeds in a topotactic manner.     

Direct electrochemistry of hemoglobin and glucose oxidase in electrodeposited sol–gel silica thin films on glassy carbon

This work points out that electrogeneration of silica gel (SG) films on glassy carbon electrodes (GCEs) can be applied to immobilize biomolecules – hemoglobin (Hb) or glucose oxidase (GOD) or both of them in mixture – without preventing their activity. These proteins were physically entrapped in the sol–gel material in the course of the electro-assisted deposition process applied to form the thin films onto the electrode surface. SG films were prepared from a precursor solution by applying a suitable cathodic potential likely to induce a local pH increase at the electrode/solution interface, accelerating thereby polycondensation of the silica precursors with concomitant film formation. Successful immobilization of proteins was checked by various physico-chemical techniques. Both Hb and GOD were found to undergo direct electron transfer, as demonstrated by cyclic voltammetry. GCE–SG–Hb gave rise to well-defined peaks at potentials E_c = −0.29 V and E_a = −0.17 V in acetate buffer, corresponding to the Fe^III/Fe^II redox system of heme group of the protein, while GCE–SG–GOD was characterized by the typical signals of FAD group at E_c = −0.41 V and E_a = −0.33 V in phosphate buffer. These two redox processes were also evidenced on a single voltammogram when both Hb and GOD were present together in the same SG film. Hb entrapped in the silica thin film displayed an electrocatalytic behavior towards O₂ and H₂O₂ in solution, respectively in the mM and μM concentration ranges. Immobilized GOD kept its biocatalytic properties towards glucose. Combined use of these two proteins in mixture has proven to be promising for detection of glucose in solution via the electrochemical monitoring of oxygen consumption (decrease of the oxygen electrocatalytic signal).     

Solubility of amphenicol bacteriostats in CO2

The solubilities of three veterinary amphenicol bacteriostats, chloramphenicol, florfenicol and thiamphenicol, were measured in supercritical carbon dioxide (SC-CO₂) by a re-circulating method at temperatures of 313.15 and 333.15 K and pressures ranging from 11.0 to 49.0 MPa. These compounds displayed very limited solubility in SC-CO₂ (10⁻⁵ to 10⁻⁷ mole fraction) over the range of experimental conditions. Chloramphenicol had the highest observed solubility of the three amphenicols, while the solubilities of florfenicol and thiamphenicol were almost an order of magnitude lower. The experimental solubility data were correlated with seven known density-based models. The density models (ln y versus ln ρ or ln ρ_r) gave better correlation than the semi-log scale of ln y versus ρ_r. Four models for ln E versus density correlations also gave better correlation than the semi-log scale of ln y versus ρ_r by introducing the enhancement factor E. The correlation accuracy of all the seven models mainly depends on the system investigated, measured density and temperature range.     

On the origin of the double layer capacitance maximum of Pt(1 1 1) single crystal electrodes

The double layer capacitance vs potential, C_dl(E), curve of Pt(1 1 1) electrodes in aqueous KClO₄ and NaF solutions exhibits a maximum at about 0.1 V vs SCE. Since with lowered solute concentrations no Gouy–Chapman minimum can be found in C_dl(E), the peak is not related to the potential of zero free charge.     

Volumetric and viscosimetric properties of N-methyl-2-pyrrolidone with γ-butyrolactone and propylene carbonate

Volumetric properties of N-methyl-2-pyrrolidone (NMP) binary mixtures with γ-butyrolactone (GBL) and propylene carbonate (PC) are calculated from the experimental densities and reported in the temperature range from (293.15 to 323.15) K and at atmospheric pressure (0.1 MPa) over the whole composition range. The excess molar volumes have positive values in the whole concentration range in the case of (NMP + PC) binary mixture, with maximum value at equimolar composition, indicating weaker interactions between the components after the mixing. Two extreme V^E values are observed in (NMP + GBL) system: maximum at x(NMP) = 0.4 and minimum at x(NMP) = 0.9. Negative V^E values in NMP-rich region are the consequence of the better geometrical fit of the molecules. The excess properties of (NMP + GBL) and (NMP + PC) binaries are analyzed using Prigogine–Flory–Paterson theoretical model. An excellent agreement between experimental and theoretical values at equimolar composition is observed. Apparent molar volumes and thermal expansion coefficients are also calculated. Viscosity measurements of the pure components and NMP binary mixtures with GBL and PC were performed in the temperature range from (298.15 to 323.15) K. Using obtained experimental viscosities several semi-empirical equations and models were tested.     

Unveiling the crucial role of temperature on the stability of oxygen reduction reaction electrocatalysts

The stability of Pt-based/C electrocatalysts used in proton exchange membrane fuel cell (PEMFC) systems is commonly evaluated via accelerated stress testing in half-cell configuration at temperature close to ambient (20 ≤ T ≤ 25 °C), and 100% relative humidity (liquid electrolyte). Those conditions are by far different from those encountered in PEMFC systems (solid electrolyte, 60 ≤ T ≤ 80 °C, 0 ≤ relative humidity ≤ 100%), and fail in reproducing the morphological changes and the performance losses encountered during real life. Here, using a high surface area Pt/C electrocatalyst, we show that the gap between half-cell and real PEMFC configurations can be bridged by considering the pronounced effect of the temperature. The accelerated stress tests (ASTs) conducted in liquid electrolyte at T = 80 °C more accurately reflect the changes in morphology and surface reactivity occurring in real PEMFC environment, and provide gain in time. Due to massive release of Pt^z + ions in the electrolyte during ASTs performed at T = 80 °C, using fresh electrolyte is strongly recommended for correct determination of the oxygen reduction reaction (ORR) kinetics.     

Assessing Si-based anodes for Ca-ion batteries: Electrochemical decalciation of CaSi2

Density functional theory (DFT) calculations are used to investigate the basic electrochemical characteristics of Si-based anodes in calcium ion batteries (CIBs). The calculated average voltage of Ca alloying with fcc-Si to form the intermetallic Ca_xSi phases (0.5 < x ≤ 2) is of 0.4 V, with a volume variation of 306%. Decalciation of the lower Ca content phase, CaSi₂, is predicted at an average voltage between 0.57 V (formation of Si-fcc, 65% volume variation) and 1.2 V (formation of metastable deinserted-Si phase, 29% volume variation). Experiments carried out in conventional alkyl carbonate electrolytes show evidence that electrochemical “decalciation” of CaSi₂ is possible at moderate temperatures. The decalciation of CaSi₂ is confirmed by different characterization techniques.     

Spontaneous deposition of Sn on Au(1 1 1). An in situ STM study

The tin adlayer formed by spontaneous deposition on Au(1 1 1) was characterized by cyclic voltammetry and in situ scanning tunneling microscopy (STM) in sulphuric acid solution. Cyclic voltammetry measurements showed oxidation peaks in the potential range −0.60 ⩽ E/V vs SSE ⩽ 0, which can be ascribed to the dissolution of the Sn adsorbed layer. STM images of the Au(1 1 1)/Sn modified surface showed that tin nucleated both on step edges and on the flat terraces forming two-dimensional islands. The anodic polarization of this modified surface produced the gradual dissolution of the Sn adlayer which was evidenced by the formation of some holes and the reduction of the initial terraces to many small islands. STM images with atomic resolution obtained on these islands displayed an hexagonal expanded atomic structure. After the anodic stripping of this Sn adsorbed layer the images exhibited the typical Au(1 1 1) terraces with a (1 × 1) atomic structure. However, at more anodic potentials another dissolution process was observed producing noticeable changes on the surface morphology which could be ascribed to the dissolution of a Au–Sn surface alloy.     

Thermodynamics of the oxidation–reduction reaction {2 glutathionered(aq) + NADPox(aq)=glutathioneox(aq) + NADPred(aq)}

Microcalorimetry, spectrophotometry, and high-performance liquid chromatography (h.p.l.c.) have been used to conduct a thermodynamic investigation of the glutathione reductase catalyzed reaction {2 glutathione_red(aq) + NADP_ox(aq)=glutathione_ox(aq) + NADP_red(aq)}. The reaction involves the breaking of a disulfide bond and is of particular importance because of the role glutathione_red plays in the repair of enzymes. The measured values of the apparent equilibrium constant K^′ for this reaction ranged from 0.5 to 69 and were measured over a range of temperature (288.15 K to 303.15 K), pH (6.58 to 8.68), and ionic strength I_m (0.091 mol · kg⁻¹ to 0.90 mol · kg⁻¹). The results of the equilibrium and calorimetric measurements were analyzed in terms of a chemical equilibrium model that accounts for the multiplicity of ionic states of the reactants and products. These calculations led to values of thermodynamic quantities at T=298.15 K and I_m=0 for a chemical reference reaction that involves specific ionic forms. Thus, for the reaction {2 glutathione_red⁻(aq) + NADP_ox³⁻(aq)=glutathione_ox²⁻(aq) + NADP_red⁴⁻(aq) + H⁺(aq)}, the equilibrium constant K=(6.5±4.4)·10⁻¹¹, the standard molar enthalpy of reaction Δ_rH^o_m=(6.9±3.0) kJ · mol⁻¹, the standard molar Gibbs free energy change Δ_rG^o_m=(58.1±1.7) kJ · mol⁻¹, and the standard molar entropy change Δ_rS^o_m=−(172±12) J · K⁻¹ · mol⁻¹. Under approximately physiological conditions (T=311.15 K, pH=7.0, and I_m=0.25 mol · kg⁻¹ the apparent equilibrium constant K^′≈0.013. The results of the several studies of this reaction from the literature have also been examined and analyzed using the chemical equilibrium model. It was found that much of the literature is in agreement with the results of this study. Use of our results together with a value from the literature for the standard electromotive force E^o for the NADP redox reaction leads to E^o=0.166 V (T=298.15 K and I=0) for the glutathione redox reaction {glutathione_ox²⁻(aq) + 2 H⁺(aq) + 2 e⁻=2 glutathione_red⁻(aq)}. The thermodynamic results obtained in this study also permit the calculation of the standard apparent electromotive force E^′o for the biochemical redox reaction {glutathione_ox(aq) + 2 e⁻=2 glutathione_red(aq)} over a wide range of temperature, pH, and ionic strength. At T=298.15 K, I=0.25 mol · kg⁻¹, and pH=7.0, the calculated value of E^′o is −0.265 V.     

Crystal structures,site occupations and phase equilibria in the system V–Zr–Ge

The V–Zr–Ge system was studied for two isothermal sections at 900 and 1200 °C. Three ternary compounds VZrGe (tI12, I4/mmm, CeScSi-type), V_xZr_5?xGe₄ (oP36, Pnma, Sm₅Ge₄-type) and V_4+xZr_2?xGe₅ (oI44, Ibam, Si₅V₆-type) were structurally characterized. Optical microscopy and powder X-ray diffraction (XRD) were used for initial sample characterization and electron probe microanalysis (EPMA) of the annealed samples was used to determine the exact phase compositions. The variation of the cell parameters of the various ternary solid solutions with the composition was determined. The three ternary phases were structurally characterized by means of single crystal and powder XRD. While VZrGe is almost a line compound, V_xZr_5?xGe₄ (0.2 ≤ x ≤ 3.0) and V_4+xZr_2?xGe₅ (0.06 ≤ x ≤ 1.2) are forming extended solid solution ranges stabilized by differential fractional site occupancy of V and Zr on the metal sites.