Distribution analysis of ultra-high molecular mass poly(ethylene oxide) containing silica particles by size-exclusion chromatography with dual light-scattering and refractometric detection

Two different size-exclusion chromatography (SEC) systems, connected in-line either to a low-angle light scattering (LALS) or to a multiangle light scattering (MALS) detector, are employed for determination of molecular mass distributions (MMD) of poly(ethylene oxide) (PEO) samples having a weight average molecular mass up to eight millions. The detrimental effect of the presence of strongly scattering silica particles in the samples on the light scattering signal can be eliminated using a suitable sample dissolution procedure utilizing silica solubility in aqueous mobile phase. The selection of flow-rate and sample concentration have a large impact on the obtained results. Hydrodynamic retardation phenomena and nonlinearity effects are shown to introduce severe errors in the molecular mass distributions unless flow-rate and sample concentration are kept at sufficiently low levels. Self-compensating ability of the dual detection in flow-rate effects is shown to be the main advantage here. A good agreement between the results obtained using LALS and MALS detection is found provided that a carefully selected angular extrapolation procedure is used in the case of MALS data. Thus, using carefully selected experimental conditions, SEC with light-scattering (LS) and refractometric detection proved to be an efficient technique for MMD characterisation also of ultra-high molecular mass (UHM) PEO polymers.     

Molecular mass distribution of sodium alginate by high-performance size-exclusion chromatography

A sensitive high-performance size-exclusion chromatography (HPSEC) method with simple UV detection was developed for the molecular mass analysis of sodium alginate. It was used to evaluate alginates of varying molecular mass and the results were compared with the viscosity measurements. This HPSEC method was sensitive to serve as the stability indicating method for alginate after storage under different conditions. The information of relative molecular mass distribution of alginate was provided with reference to pullulan molecular mass standards. The comparison of the HPSEC chromatograms of alginate, pullulan and dextran revealed the effect of chemical composition of a polysaccharide and its effect on apparent molecular mass distribution.     

Estimation of uncertainty in size-exclusion chromatography with a double detection system (light-scattering and refractive index)

Size-exclusion chromatography (SEC) coupled with online laser light-scattering (LS) and refractive index (RI) detection provides an excellent approach to determine the molecular weights (Mw) of proteins by the “two-detector” approach. Mw is determined only at the maximum of a peak, using either peak heights or area ratio from the two detectors. However, proper calibration of the SEC/LS/RI system is critical to obtain high precision.Today, an essential part of any analysis is to evaluate the uncertainty associated with the method. Basically, it is possible to distinguish between factors related to signal nature, precision and those due to signal processing. Given the signal of interest is the peak height or area ratio from two detectors, the signal ratio uncertainty was calculated using the random propagation of error formula. In this case, the effect of signal correlation was evaluated to avoid the uncertainty overestimation. In the second case, the sources of uncertainty affecting analytical measurement were estimated with the information from the precision assessment. For this, two designs with two-factor fully nested were followed for each method. Finally, the contributions from various uncertainty sources related with calibration are also analysed in detail. There are in fact only three main sources of measurement uncertainty: intermediate precision, calibration and repeatability. Of these, method precision is always the greatest, regardless of approach.For all proteins and peptides studied, the Mw calculated using both methods are close to the theoretical results, independently of the design, but the contributions of individual terms to combined uncertainty depend on both the design and method used. For example, the combined uncertainty varied between 223 and 813.2 Da for carbonic anhydrase, although higher values were found for human insulin and ovalbumin dimer. Other considerations that can have a significant impact on the results are discussed.The reproducibility of the two methods versus that based on ASTRA software used as reference method was performed using the concordance correlation coefficient. The methods’ reproducibility depends on the permitted losses in precision and accuracy.     

Molar mass characterization of cationic methyl methacrylate-ethyl acrylate copolymers using size-exclusion chromatography with online multi-angle light scattering and refractometric detection

Size-exclusion chromatography (SEC) combined with online multi-angle light scattering (MALS) and refractometric (RI) detection has been employed for the molar mass characterisation of water-insoluble cationic methyl methacrylate-ethyl acrylate copolymers (Eudragit RS and RL). Due to their positive charge, cationic polymers are particularly difficult to separate on a SEC column, in worst cases being completely adsorbed on the oppositely charged packing material. This work has examined how a careful addition of salt (LiCl) to the copolymer solution in ethanol decreases the electrostatic interactions, clearly seen as a decrease in elution volume from the SEC column as well as an improved recovery. At a certain level of ionic strength, typically about 50 mM, the copolymer recovery from the SEC column reached 100% and molar mass distributions corresponding to the complete sample could be obtained. The combined MALS/RI detection gives the opportunity to measure the absolute molar mass independent of recovery and retention. Thus, in this study, it turned out to be a favourable tool for tracing the changes in elution behaviour of the charged copolymer as the ionic strength was increased.     

Direct analysis of industrial oligoglycerols by liquid chromatography with evaporative light-scattering detection and mass spectrometry

Summary A liquid chromatographic method has been developed for analysis of industrial polyglycerols, precursors of polyglycerol fatty esters, which are non-ionic surfacetants. The method utilizes two complementary chromatographic systems: porous graphitic carbon and an aminopropyl polymer with an acetonitrile-water mixture as mobile phase. Detection of these non-UV absorbing compounds was effected by means of evaporative light-scattering detection. Their structures were determined by comparison of their retention with that of synthesized standards, and by mass spectrometry.     

Interactions between covalently crosslinked ethyl(hydroxyethyl)cellulose and SDS

The equilibrium swelling of chemically crosslinked gels based on ethyl(hydroxyethyl)cellulose (EHEC) in aqueous solutions of sodium dodecyl sulphate (SDS) was studied as a function of the SDS concentration at various temperatures and salt concentrations. Comparisons were made with gels based on poly-N-isopropylacrylamide (p-NIPA). Both polymers are known to form complexes with SDS above a critical association concentration (cac) of the surfactant, and both display a lower critical solution temperature (LCST) in water. For both types of gels, an increase in the equilibrium gel volume was seen with increasing SDS concentration above the cac, up to a maximum value when the SDS concentration in the external solution reached the critical micelle concentration (cmc). Above the cmc, the equilibrium gel volume decreased slowly with increasing SDS concentration. A volume collapse of the EHEC gels was observed in a temperature interval around the LCST of EHEC in solution. Above the cac, the collapse transition moved monotonically towards higher temperatures with added SDS. At lower SDS concentrations, however, the opposite trend was found. The swelling of the gel was less in the presence of salt and SDS, and a pronounced minimum in swelling appeared with added SDS when the salt concentration was sufficiently high (ca. 10 mmoles/l). Under these salt conditions, the LCST of the linear EHEC also passes through a deep minimum (below room temperature) on addition of SDS.     

Molecular mass determination of polyamic acid ionic salt by size-exclusion chromatography

A methodology was developed for the determination of molecular weight aveages of polyamic acid ionic salt (PAS) by size-exclusion chromatography (SEC). Polystyrene standards were used for calibration and THF-DMF 1:1 by volume containing 0.06 M LiBr and 0.06 M H3PO4 was used as the mobile phase. The proposed methodology was found to be reproducible.     

Determination of molecular parameters of hydroxyethyl and hydroxypropyl celluloses by chromatography with dual detection

Hydroxyethylcellulose (HEC) and hydroxypropylcellulose (HPC) were studied by means of size exclusion chromatography with dual detection, i.e. employing simultaneously a refractive index (concentration sensitive) and a multiangle light scattering (molecular weight sensitive) detectors. The eluent was water and water solutions containing different concentrations of ionic salts. Molecular weight distributions and averages, coefficients of the scaling law of molecular dimensions and unperturbed dimensions were thus obtained from a single polydisperse sample of each polymer. Measurements were performed at 25 degrees C and the anomalous chromatographic behaviour, due to a combination of ion and size exclusion mechanisms, found when using pure water as eluent is transformed into a size exclusion mechanism by the addition of ionic salts. However, the two polymers behave on a different way in presence of salts. Thus, HEC, which is of low degree of substitution (DS), is close to theta conditions in the aqueous salt solutions (i.e. the q exponent of the scaling law has a value close to 0.5), whereas in the case of HPC the addition of salt improves the quality of the solvent up to a value of q around 0.6. Unperturbed dimensions are also calculated for both celluloses.     

Characterization of dextrans by size-exclusion chromatography on unmodified silica gel columns, with light-scattering detection, and capillary electrophoresis with laser-induced fluorescence detection

Unmodified silica gel size-exclusion columns were used in an on-line combination with light-scattering detection for a size characterization of dextrans. The influence of electrostatic interactions on analyte retention was briefly investigated. Size-exclusion chromatography was also used for evaluation of the fluorescence labeling procedure for dextrans with 8-aminonaphthalene-1,3,6-trisulfonic acid. The derivatives obtained through this procedure were used for electrophoretic measurements with laser-induced fluorescence detection. A comparison between the size-exclusion data and capillary electrophoresis indicates that the effectiveness of fluorescent labeling decreases with molecular mass of the dextran analytes.     

Quantitative trace analysis of surfactant mixtures by reversed-phase high-performance liquid chromatography with refractometric detection

Reversed-phase partition liquid chromatography on an octyl column allowed the separation of complex non-ionic poly(ethylene oxide)-type (PEO) surfactant mixtures resulting from the condensation of ethylene oxide with saturated fatty alcohols. As these compounds have no chromophoric group, they were detected by differential refractometry. Accurate quantitation of each oligomer (C_mE_n) allowed the main characteristics of each non-ionic surfactant, i.e., the nature and percentage of the different alkyl chains (with m = number of carbons) and the average number of ethylene oxide units ( ) to be obtained in one analysis. Preparative liquid chromatography was used to isolate pure oligomers with a higher degree of ethoxylation (n =10, 11, 12, 14 and more) than the commercially available standards, in order to determine a wide range of refractometric response factors. It appeared that they are constant as a function of alkyl chain length (C₁₀-C₁₆ range) but that they vary significantly and non-linearly as a function of the degree of ethoxylation, n. It was found that neglecting the variation of response factors can result in a distortion of the average ethoxylation number and in an unsatisfactory quantitative analysis. This chromatographic method, involving a quantitative and reproducible trace enrichment procedure with liquid-solid extraction, allowed the analysis of very dilute PEO mixtures in water. The components of complex PEO mixtures in water were determined at concentrations as low as 0.5 mg 1⁻¹, without any distortion of the distribution, the detection limit being 0.25 μg 1⁻¹ for the less abundant oligomers.     

Interactions between ethyl(hydroxyethyl) cellulose and lysine-based surfactants in aqueous media

In this work, the interaction between ethyl(hydroxyethyl) cellulose (EHEC) and three dimeric lysine-based surfactants of distinct chain length (C₆, C₈ and C₁₀) have been assessed and the system was evaluated in terms of its temperature-dependent gelling capacity. The viscosity profile depends on the specific surfactant, its concentration and temperature. The observed profiles reflected polymer–polymer associations at elevated temperatures and polymer-surfactant interactions, implying the formation of micellar-type associations. The systems induce gelation at higher temperatures. Longer chain-length surfactants induce gelation at lower concentrations due to their stronger tendency to self-assemble. The thermo-responsive gels showed gel strength generally lower than 20 Pa.sⁿ and a fractal dimension of 2.3–2.4, respectively, indicating the formation of soft gels comprising a tight and homogeneous network. The weakest gel was produced in the presence of the C₆ surfactant. 2D Small-Angle Light Scattering patterns showed a pronounced effect of temperature in terms of the evolution of large hydrophobic clusters, an event precluded when high concentrations of the longer chain surfactants were used.     

Polymer characterization by size-exclusion chromatography with multiple detection.

Size-exclusion chromatography with coupled multiangle light scattering and differential refractometry detectors has been used to obtain molecular mass and radius of gyration distributions of polydisperse polymer samples. From these data the scaling law between dimensions and the absolute molecular mass is obtained with just one sample of each polymer. Three different kinds of polymers are presented: polystyrene which serves as reference polymer, polyphosphazenes which behave abnormally in solution and poly(ethylene oxide) which is soluble in water. Since the relationship between dimensions and molecular mass depends on the extent of interactions between chain segments and solvent molecules, the scaling law provides information about the solution properties of the polymer.     

Interaction between ethyl(hydroxyethyl)cellulose and sodium dodecyl sulphate in aqueous solution

Using sodium activity, viscosity, and cloudpoint measurements, it has been shown that sodium dodecyl sulphate (SDS) binds to ethyl(hydroxyethyl)cellulose in a cooperative manner. In the absence of salt the binding leads to an increase in the clouding temperature, but when a small amount of salt (0.01 molal) is present first a drastic decrease and then an equally drastic increase in the cloud point temperature is observed. The binding of SDS also initially leads to an increase in viscosity followed by a decreased viscosity at higher SDS concentrations. A molecular mechanism explaining the observed behavior is given.     

Characterization of implant device materials using size-exclusion chromatography with mass spectrometry and with triple detection

A more complete understanding of the raw materials used for making implant device materials becomes increasingly important in the medical device industry. Often such detailed information requires utilization of a combination of analytical techniques. In this work, we characterize a poly(dimethyl siloxane) (PDMS) material using on-line size exclusion chromatography (SEC) with electrospray ionization (ESI) and matrix assisted laser desorption ionization (MALDI) mass spectrometry (MS) techniques. Here, we obtain detailed molecular compositional information such as repeat units, end group chemistry, and identification of impurities in both the high and low mass range. SEC with light scattering, viscosity, and refractive index detection (triple detection) is used to obtain information on a small quantity of high mass impurity that was undetected by both SEC-ESI and MALDI MS techniques. SEC with triple detection measures absolute molecular weights and molecular weight distributions. We compare average molecular weight values of the implantable device polymer obtained by SEC with triple detection, SEC-ESI, and SEC-MALDI MS techniques.     

Measurement of uncertainty in peptide molecular weight determination using size-exclusion chromatography with multi-angle laser light-scattering detection and matrix-assisted laser desorption/ionization time-of-flight mass spectrometry

The molecular weight of biopolymers such as peptides or proteins is vital information for understanding their physical/chemical properties. The matrix-assisted laser desorption/ionization time-of-flight mass spectrometry (MALDI-TOF-MS) and size-exclusion chromotography-multi-angle laser light scattering (SEC-MALLS) techniques each with its advantages and limitations were used for molecular weight determination of the SPf66 peptide. The precision of each method was studied using a two-factor fully-nested design with all the analyses performed by the same operator on a single instrument. The overall precision corresponded to the time-different intermediate precision (i.e. time and repeatability conditions). In the case of SEC-MALLS, all potential uncertainty components were carefully evaluated in an Ishikawa diagram, then included and mathematically combined with the uncertainty arising from the accuracy assessment to provide the overall uncertainty. In this case, the refractive-index increment with solute concentration value (dn/dc) provided the most significant contribution to the combined uncertainty. A method for its quantitation is proposed. The accuracy of method B (SEC-MALLS) against reference method A (MALDI-TOF-MS) was assessed using the interval testing hypothesis to limit the risk of unacceptable bias. The results indicate that the bias of B is higher than the limit established at 5%, and is therefore not traceable to A under the studied conditions.     

Gels of hydrophobically modified ethyl(hydroxyethyl) cellulose cross-linked by amylose: effects of hydrophobe architecture

Previous work has shown that amylose (AM) can cross-link hydrophobically modified polymers by inclusion complexation, whereby thermoreversible cold-setting gels are formed. Here we investigate the complexation of AM with different samples of hydrophobically modified ethyl(hydroxyethyl) cellulose (HMEHEC), distinguished by differences in the architecture of the hydrophobes (the hydrophobic side chains). All hydrophobes, except one, were based on linear alkyl chains, but with varying chain lengths (C12-C14). In addition, some samples contained short hydrophilic "spacers", consisting of 2-5 ethylene oxide units, between the alkyl chains and the EHEC backbone. Gels of varying strength were obtained for the different AM/HMEHEC samples. The alkyl chain length seemed to be the major factor affecting the gel strength, with longer alkyl chains giving stronger gels. For similar alkyl chain lengths, stronger gels were obtained when a spacer was present. Addition of AM caused a small increase of the cloud points of HMEHECs with C14 hydrophobes in water. Time-dependent effects and effects of the sample preparation procedure were also investigated. The reversibility of the gelation with respect to shear was confirmed. A gel destroyed by added surfactant was shown to reform on removal of the surfactant by dialysis.     

Conductivity detection for molecular mass estimation of per-O-sulfonated glycosaminoglycans separated by high-performance size-exclusion chromatography

Chemically per-O-sulfonated polysaccharides, including glycosaminoglycans (GAGs) and hyaluronan oligosaccharides were analyzed using high-performance size-exclusion chromatography (HPSEC) with suppressed conductivity detection. The results were compared to those obtained by gel filtration HPLC using UV detection or fluorescence detection after the post-column reaction with 2-cyanoacetamide in strong alkaline solution. Analysis was performed on a TSKgel G3000SWXL HPSEC column in 5 mM boric acid (pH 7.0 adjusted by 10 mM NaOH). The use of conductivity detection, in the absence of any derivatization and under isocratic conditions gave a limit of detection in the picogram range. Preliminary studies suggest that this approach may be particularly useful in examining sulfonated polysaccharides and oligosaccharides having no UV chromophore, such as those prepared from O-sulfonated fucans and galactans isolated from algae.     

Quantitative analysis of hydrophobic pulmonary surfactant proteins by high-performance liquid chromatography with light-scattering detection

A new method for the separation and quantification of two hydrophobic lung surfactant proteins (SPs) is described. It is based on size-exclusion chromatography using the apolar stationary phase butyl silicagel with a pore size of 30 nm and isocratic elution with chloroform, methanol and trifluoroacetic acid. The samples were prepared from sheep lung lavage fluid by centrifugation and fractional extraction with butanol and chloroform–methanol. The chromatograms show three peaks in the elution order SP-B, SP-C and lipids. A small peak ahead of SP-B, which disappeared after reduction with 2-mercaptoethanol, was oligomeric SP-B. The response of the evaporative light-scattering detector was non-linear. For preparative high-performance liquid chromatography ultraviolet detection at 279 nm is recommended.