Ⅱ型动态扩展裂纹尖端的弹黏塑性渐近场

考虑材料的黏性效应建立了Ⅱ型动态扩展裂纹尖端的力学模型,假设黏性系数与塑性等效应变率的幂次成反比,通过分析使尖端场的弹、黏、塑性得到合理匹配,并给出边界条件作为扩展裂纹定解的补充条件,对理想塑性材料中平面应变扩展裂纹尖端场进行了弹黏塑性渐近分析,得到了不含间断的连续解,并讨论了Ⅱ型裂纹数值解的性质随各参数的变化规律.分析表明应力和应变均具有幂奇异性,对于Ⅱ型裂纹,裂尖场不含弹性卸载区.引入Airy应力函数,求得了Ⅱ型准静态裂纹尖端场的控制方程,并进行了数值分析,给出了裂纹尖端的应力应变场.当裂纹扩展速度(M→0)趋于零时,动态解趋于准静态解,表明准静态解是动态解的特殊形式.     

双材料界面Ⅰ型扩展裂纹尖端的弹黏塑性场

双材料界面中存在材料黏性效应, 对界面裂纹尖端场的分布和界面本身性能 的变化起着重要的影响. 考虑裂纹尖端的奇异性, 建立了双材料界面扩展裂纹尖端的弹黏塑 性控制方程. 引入界面裂纹尖端的位移势函数和边界条件, 对刚性-弹黏塑性界面I型界面 裂纹进行了数值分析, 求得了界面裂纹尖端应力应变场, 并讨论了界面裂纹尖端场随各影响 参数的变化规律. 计算结果表明, 黏性效应是研究界面扩展裂纹尖端场时的一个主要因素, 界面裂纹尖端为弹黏塑性场, 其场受材料的黏性系数、马赫数和奇异性指数控制.     

压-剪混合型定常扩展裂纹尖端的弹黏塑性场

假定黏性系数与塑性等效应变率的幂次成反比,考虑其黏性和裂纹面摩擦接触效应 建立了压-剪混合型定常扩展裂纹尖端弹黏塑性场的渐近方程,求得了裂纹尖端场不含应力、应变间 断的数值解. 并讨论了压-剪混合型裂纹数值解随各个参数的变化规律,计算结果 和分析表明,压-剪混合型裂纹尖端场是满塑性的,不含有弹性卸载区,黏性效应是研究扩展裂纹尖端场时的一个重要因素. 无论混合裂纹趋近I型还是趋近II型,静水压力随摩擦系数的增加都是增加的,裂纹面摩擦 效应是阻止裂纹扩展速度的因素,且摩擦作用越强,裂纹尖端场的韧性越高.     

稳恒扩展裂纹尖端的弹粘塑性场

采用弹粘塑性力学模型代替通常的弹塑性模型，对于I型和Ⅱ型问题，分别求得了不可压缩材料中平面应变动态扩展裂纹尖端的指数奇异性场和对数奇异性场，消除了弹塑性解中存在的塑性激波。通过数值计算，分别求得了两种奇异属性的分界线，建立起统一的裂纹尖端奇异性场。     

扩展裂纹尖端塑性场

本文通过对幂硬化材料中平面应变Ｉ型裂纹的扩展过程进行精细的弹塑性有限元计算，给出扩展裂纹尖端附近环形区域内弹塑性场的分布。首次提出适用于扩展裂纹尖端环形区域的三项解。其中首项为ＨＲＲ奇异解；第二项反映三轴应力的强弱；第三项与ＨＲＲ奇异性项相比还含有线性项。并指出：扩展裂纹尖端环形区域弹塑性应力应变场的分布和强弱可由Ｊ－Ｑ－ｋ２三参量刻划，此结论适用于不同试样几何。不同材料硬化指数以及由小范围屈服至     

正交异性介质中定常扩展裂纹尖端应力,应变场

本文将正交异性材料视为理想弹塑性材料,采用R.Hill屈服准则及与之相关的流动法则,推导了平面应变Ⅰ型定常扩展裂纹的基本方程。在假定材料不可压缩的条件下,获得了泊桑系数间的相互关系v_(31) v_(32)=1,进一步还假定了v_(31)=G/(F G),v_(32)=F/(F G),因而获得了问题的分析解。结果表明,应变场具有ln(A/r)的奇异性。     

蠕变材料Ⅰ型动态扩展裂纹尖端场

为了研究黏性效应作用下的动态扩展裂纹尖端渐近场,建立了蠕变材料Ⅰ型动态扩展裂纹的 力学模型.首先,依据在稳态蠕变阶段,弹性变形和黏性变形同时在裂纹尖端场中占主导地 位,由量级协调可知,应力和应变具有相同的奇异量级,即(σ,ε)∝/ r- 1/(n-1). 其次,通过渐近分析推导出动态扩展裂纹尖端场的控制方程并求得了裂纹尖端应 力、应变和位移分离变量形式的渐近解.最后,采用双参数打靶法求得了裂纹尖端应力、应 变的数值结果.数值计算表明,裂尖场主要受材料的蠕变指数n和马赫数M的控制;在Ⅰ 型动态扩展裂纹前方,环向应变达到最大值,可据此建立断裂准则. 由于裂纹稳定扩展与非稳定扩展的主奇异项相同,因此对于稳定扩展裂纹的渐近分析方 法,同样适用于非稳定的裂纹扩展问题.     

蠕变硬化材料中Ⅱ型扩展裂纹尖端场特性研究

采用弹牯塑性力学模型,对蠕变硬化材料中平面应变扩展裂纹尖端场进行了渐近分析.假设人工粘性系数与等效塑性应变率的幂次成反比,通过量级匹配表明应力和应变均具有幂奇异性,奇异性指数由粘性系数中等效塑性应变率的幂指数唯一确定.通过数值计算讨论了Ⅱ型准静态扩展裂纹尖端场的分区构造以及裂纹尖端应力和应变场的特性随各材料参数的变化规律,结果表明裂尖场由材料的粘性和塑性共同主导.当硬化系数为零时裂尖场可退化为相应的HR场.     

幂硬化弹塑性-刚性界面Ⅲ型定常扩展裂纹尖端的渐近场

对幂硬化弹塑性材料－刚性材料界面上裂纹以定常方式扩展的Ⅲ型问题进行弹塑性渐近分析，给出裂纹尖端的应力，应变和位移场解。通过数值计算，考察了不同Mach数以及裂纹尖端混合参数对场解的构造以及应力，应变分布的影响，为给出合理的断裂准则提供理论依据。     

Perfect elastic-viscoplastic field at mode I dynamic propagating crack-tip

The viscosity of material is considered at propagating crack-tip. Under the assumption that the artificial viscosity coefficient is in inverse proportion to power law of the plastic strain rate, an elastic-viscoplastic asymptotic analysis is carried out for moving crack-tip fields in power-hardening materials under plane-strain condition. A continuous solution is obtained containing no discontinuities. The variations of numerical solution are discussed for mode I crack according to each parameter. It is shown that stress and strain both possess exponential singularity. The elasticity, plasticity and viscosity of material at crack-tip only can be matched reasonably under linear-hardening condition. And the tip field contains no elastic unloading zone for mode I crack. It approaches the limiting case, crack-tip is under ultra-viscose situation and energy accumulates, crack-tip begins to propagate under different compression situations.     

Perfect elastic-viscoplastic field at mode Ⅰ dynamic propagating crack-tip

The viscosity of material is considered at propagating crack-tip. Under the assumption that the artificial viscosity coefficient is in inverse proportion to power law of the plastic strain rate, an elastic-viscoplastic asymptotic analysis is carried out for moving crack-tip fields in power-hardening materials under plane-strain condition. A continuous solution is obtained containing no discontinuities. The variations of numerical solution are discussed for mode Ⅰ crack according to each parameter. It is shown that stress and strain both possess exponential singularity. The elasticity, plasticity and viscosity of material at crack-tip only can be matched reasonably under linear-hardening condition. And the tip field contains no elastic unloading zone for mode Ⅰ crack. It approaches the limiting case, crack-tip is under ultra-viscose situation and energy accumulates, crack-tip begins to propagate under different compression situations.     

VISCOPLASTIC SOLUTION TO FIELD AT STEADILY PROPAGATING CRACK TIP IN LINEAR- HARDENING MATERIALS

An elastic-viscoplastic constitutive model was adopted to analyze asymptotically the tip-field of moving crack in linear-hardening materials under plane strain condition. Under the assumption that the artificial viscosity coefficient was in inverse proportion to power law of the rate of effective plastic strain, it is obtained that stress and strain both possess power law singularity and the singularity exponent is uniquely determined by the power law exponent of the rate of effective plastic strain. Variations of zoning structure according to each material parameter were discussed by means of numerical computation for the tip-field of mode Ⅱ dynamic propagating crack, which show that the structure of crack tip field is dominated by hardening coefficient rather than viscosity coefficient. The secondary plastic zone can be ignored for weak hardening materials while the secondary plastic zone and the secondary elastic zone both have important influence on crack tip field for strong hardening materials. The dynamic solution approaches to the corresponding quasi-static solution when the crack moving speed goes to zero, and further approaches to the HR (Hui-Riedel) solution when the hardening coefficient is equal to zero.     

ASYMPTOTIC DYNAMIC SOLUTION TO THE MODE Ⅰ PROPAGATING CRACK-TIP FIELD IN ELASTIC-VISCOPLASTIC MATERIAL

A new elastic-viscoplastic mode was proposed to analyze the stress and strain fields surrounding the tip of a propagating mode Ⅰ cracks. A proper displacement pattern was suggested and asymptotic equations were derived, and numerical solutions were illustrated. The analysis and calculation show that the crack-tip field is of logarithmic singularity for smaller viscosity, however no solution exists for large viscosity. By a careful analysis and comparison, it is found that the present results retain all merits of those given by Gao Yu-chen, while removing existing problems.     

Steady-state growing crack-tip field characteristics of mode Ⅲ elastic-viscoplastic/rigid interface cracks

The existence of viscosity effect at the interface of double dissimilar materials has an important impact on the distribution of the interface crack-tip field and the properties variety of the interface itself. The singularity and viscosity are considered in the crack-tip. The elastic-viscoplastic governing equations of double dissimilar materials at the interface crack-tip field are established. The displacement potential function and boundary condition of interface crack-tip are introduced. The numerical analysis of elastic-viscoplastic/rigid interface for mode Ⅲ is worked out. The stress-strain fields are obtained at the crack-tip and the variation rules of solutions are discussed according to each parameter. The numerical results show that the viscosity effect is a main factor of the interface propagating in the crack-tip field, and the interface crack-tip is a viscoplastic field governed by the viscosity coefficient, Mach number (Ma), and singularity exponent.     

Perfect elastic-viscoplastic field at mode Ⅰ dynamic propagating crack-tip

The viscosity of material is considered at propagating crack-tip. Under the assumption that the artificial viscosity coefficient is in inverse proportion to power law of the plastic strain rate, an elastic-viscoplastic asymptotic analysis is carried out for moving crack-tip fields in power-hardening materials under plane-strain condition. A continuous solution is obtained containing no discontinuities. The variations of numerical solution are discussed for mode Ⅰ crack according to each parameter. It is shown that stress and strain both possess exponential singularity. The elasticity, plasticity and viscosity of material at crack-tip only can be matched reasonably under linear-hardening condition. And the tip field contains no elastic unloading zone for mode I crack. It approaches the limiting case, crack-tip is under ultra-viscose situation and energy accumulates, crack-tip begins to propagate under different compression situations.     

Effect of poisson ratio on the perfectly plastic field at a rapidly propagating plane-strain crack-tip

All the stress components at a rapidly propagating crack-tip in elastic perfectly-plasticmaterial are the functions ofθonly.Making use of this condition and the equations ofsteady-state motion,plastic stress-strain relations,and Mises yield condition with Poissonratio,in this paper,we derive the general expression of perfectly plastic field at a rapidlypropagating plane-strain crack-tip.Applying this general expression with Poisson ratio toModeⅠcrack,the perfectly plastic field at the rapidly propagating tip of ModeⅠplane-strain crack is obtained.This perfectly plastic field contains a Poisson ratio,and thus,wecan obtain the effect of Poisson ratio on the perfectly plastic field at the rapidly propagatingtip of ModeⅠplane-strain crack.     

Field structure at mode III dynamically propagating crack tip in elastic-viscoplastic materials

An elastic-viscoplastic mechanics model is used to investigate asymptotically the mode Ⅲ dynamically propagating crack tip field in elastic-viscoplastic materials. The stress and strain fields at the crack tip possess the same power-law singularity under a linear-hardening condition. The singularity exponent is uniquely determined by the viscosity coefficient of the material. Numerical results indicate that the motion parameter of the crack propagating speed has little effect on the zone structure at the crack tip. The hardening coefficient dominates the structure of the crack-tip field. However, the secondary plastic zone has little influence on the field. The viscosity of the material dominates the strength of stress and strain fields at the crack tip while it does have certain influence on the crack-tip field structure. The dynamic crack-tip field degenerates into the relevant quasi-static solution when the crack moving speed is zero. The corresponding perfectly-plastic solution is recovered from the linear-hardening solution when the hardening coefficient becomes zero.     

Anisotropic plastic fields at a rapidly propagating plane-stress crack-tip

Under the condition that all the stress components at a crack-tip are the functions ofθonly,making use of the equations of steady-state motion.Hill anisotropic yield condition and stress-strain relations,we obtain the general solution of anisotropic plastic field at a rapidly propagating plane-stress crack-tip.Applying this general solution to four particular cases of anisctropy,the general solutions of these four particular cases are derived.Finally,we give the anisotropic plastic field at the rapidly propagating plane-stress modeⅠcrack-tip in the case of X=Y=Z