TiO2纳米微球的制备及在染料敏化太阳能电池中的应用

以四氯化钛、盐酸为原料,制备出花状TiO₂纳米微球,利用扫描电子显微镜（SEM）、X射线衍射（XRD）等测试方法,对样品的结构和形貌进行了表征。为了提高TiO₂微球电池的光电性能,利用TiO₂微球作为反射层构造了双层结构的薄膜电极,结果表明,双层结构染料敏化太阳能电池在100 mW·cm^-2（1.5 G）光照条件下,短路光电流J_sc为17.64 mA·cm^-2,开路光电压Voc为0.74 V,填充因子FF为0.63和光电转化效率η为8.33%。相比TiO₂微球制备的太阳能电池,双层结构染料敏化太阳能电池光电转化效率提高至5.3倍。最后对电极中染料的吸附量、电极的光散射性能和电池的电化学阻抗做了进一步研究和分析,研究表明,双层结构电池增强光的捕获能力,从而提高光伏性能。     

上转换发光在染料敏化太阳能电池中的应用

以水热和高温煅烧相结合的方法制备了掺Er³⁺的TiO₂上转换发光层,并将其组装在染料敏化太阳能电池(DSSC)中。通过XRD﹑荧光光谱﹑UV-Vis和电池的光电性能测试,分析了上转换发光层的发光机理及其加入后对染料敏化太阳能电池性能的影响。结果表明,上转换发光层的引入有效地提高了DSSC的光电性能,在80 mW·cm^-2红外光照射下最高光电转换效率达到了0.14‰,比未加上转换发光层的DSSC提高了160%。     

含有TiO2刺球散射中心光阳极的设计及其在染料敏化太阳能电池的应用

采用水热法制备了一种刺球状TiO₂（NT）,将其作为光散射中心,与纳米晶TiO₂混合,制备成一种底层为P25薄膜（作为染料吸收层）,上层为添加NT散射层的混合结构的薄膜光阳极。探讨了NT添加量对薄膜性能的影响,实验结果表明,当NT与P25粉体的质量比为35%时电池光电性能最优,电池短路光电流密度为14.30 mA·cm^-2,其光电转换效率达到7.38%。质量比继续增大,当达到50%时电池性能有所下降,光电转换效率降为5.99%,同时染料吸附量也由73.2 μmol·cm^-2降到70.1 μmol·cm^-2。这表明过量的大颗粒TiO₂刺球散射中心会减少光阳极的比表面积从而降低染料的有效吸附量,并且还会引起不必要的反向散射,只有适量的散射中心才能得到最佳性能的太阳能电池器件。     

染料敏化太阳能电池中大孔TiO2薄膜电极的制备及应用

采用溶胶-凝胶水热法制备了TiO₂纳晶薄膜电极，晶型为锐钛矿型。为了提高电极的光电性能，利用聚苯乙烯小球做造孔剂，制备了含有大孔隙的TiO₂纳晶薄膜电极，孔径约为200 nm，该电极具有较好的光漫反射性能，更重要的是球形大孔的存在，提高了凝胶电解质在TiO₂薄膜电极中的渗透和I₃^-离子的扩散性能，与不含大孔的TiO₂电极相比，电池的短路光电流提高约2 mA·cm^-2，光电转换效率提高0.6%。     

I2界面修饰对全无机CsPbBr3钙钛矿太阳能电池性能的影响

通过在 CsPbBr₃薄膜上旋涂一次 I₂的异丙醇溶液以修饰 CsPbBr₃吸光层,钝化 CsPbBr₃层表面缺陷,改善 CsPbBr₃薄膜形貌。同时通过利用环境友好的绿色溶剂水溶解 CsBr,显著提高了其溶解度,减少了旋涂次数,简化了电池制备流程。实验结果表明,在CsPbBr₃钙钛矿太阳能电池(perovskite solar cells,PSCs)中,使用5 mg·mL^-1 I₂的异丙醇溶液界面修饰的器件具有最佳光伏性能,其最高开路电压(open-circuit voltage,V_OC)为1.55 V,短路电流密度(short circuit current density,J_SC)为7.45 mA·cm^-2,填充因子(fill factor,FF)为85.54%,光电转换效率(photoelectric conversion efficiency,PCE)达到了9.88%。     

I2界面修饰对全无机CsPbBr3钙钛矿太阳能电池性能的影响

通过在 CsPbBr₃薄膜上旋涂一次 I₂的异丙醇溶液以修饰 CsPbBr₃吸光层,钝化 CsPbBr₃层表面缺陷,改善 CsPbBr₃薄膜形貌。同时通过利用环境友好的绿色溶剂水溶解 CsBr,显著提高了其溶解度,减少了旋涂次数,简化了电池制备流程。实验结果表明,在CsPbBr₃钙钛矿太阳能电池(perovskite solar cells,PSCs)中,使用5 mg·mL^-1 I₂的异丙醇溶液界面修饰的器件具有最佳光伏性能,其最高开路电压(open-circuit voltage,V_OC)为1.55 V,短路电流密度(short circuit current density,J_SC)为7.45 mA·cm^-2,填充因子(fill factor,FF)为85.54%,光电转换效率(photoelectric conversion efficiency,PCE)达到了9.88%。     

表面修饰的TiO2太阳能电池界面特性研究

用水热法制备了具有典型锐钛矿晶型的TiO₂纳米材料,采用Cr(NO₃)₃对TiO₂薄膜电极进行修饰改性。用X射线衍射(XRD)、扫描电子显微镜(SEM)和光电子能谱(XPS)测试电极的物相及表面结构,结果显示TiO₂薄膜表面包覆一层粒径较大的氧化铬颗粒,整个电极仍保持均匀的多孔结构。电流-电压(Ⅰ-Ⅴ)曲线测试结果显示,改性后最佳电极的短路电流和光电转换效率分别比改性前提高了31.1%和40.4%。用电化学阻抗谱(EIS)测试电池的界面特性,从测试结果可以看出,相同偏压下,改性后电池的TiO₂/染料/电解质界面电阻更大,说明氧化铬包覆层在一定程度上抑制了界面的电子复合,改善了电池的光电输出特性。     

(Pr0.9La0.1)2(Ni0.74Cu0.21Ga0.05)O4+δ-Ce0.9Gd0.1O2-δ复合阴极的制备及电化学性质

采用EDTA-柠檬酸盐法制备了（Pr_0.9La_0.1）₂（Ni_0.74Cu_0.21Ga_0.05）O_4+δ（PLNCG）,并与Ce_0.9Gd_0.1O_2-δ（CGO）形成复合阴极PLNCG-CGO。XRD和SEM分析结果表明PLNCG与CGO在1 000℃具有较好的化学相容性。电化学阻抗测试结果表明PLNCG-30% CGO复合阴极在700℃的极化电阻为0.092 Ω·cm²;过电位为39.3 mV时,电流密度达到113.3 mA·cm^-2。氧分压分析表明电极反应的速率控制步骤为电荷转移过程。阳极支撑单电池（Ni-CGO/CGO/PLNCG-30% CGO）在700℃的最大输出功率密度达到569 mW·cm^-2,开路电压（OCV）为0.76 V。综上结果预示PLNCG-30% CGO复合阴极是一种有发展前景的电极材料。     

染料敏化稀土离子修饰二氧化钛纳米晶电极的光电化学性质

制备了N3染料敏化的稀土离子表面修饰二氧化钛纳米晶电极. 由于在新电极表面形成了一个势垒, 这个势垒可以有效地抑制电极表面的电荷复合, 因此改善了电极的光电转化性质. 其中N3染料敏化Yb³⁺离子修饰TiO₂电极在73.1 mW/cm²白光照射下的光电转化效率比TiO₂电极增大了15%.     

染料敏化纳米薄膜太阳电池中DMPII浓度的优化

利用超微铂电极和循环伏安法及电化学阻抗谱研究了在1,2-二甲基-3-丙基咪唑碘(DMPII)的3-甲氧基丙腈(MePN)溶液中I₃^－和I^－的氧化还原行为，并对比了由不同浓度的I2和DMPII组成的电解质溶液，其染料敏化纳米薄膜太阳电池(DSCs)的光伏性能. 发现以MePN为溶剂，含1.0 mol•dm^-3 DMPII、0.12 mol•dm^-3 I2、0.10 mol•dm^-3 LiI和0.50 mol•dm^-3 4-叔丁基吡啶的电解质溶液，其DSCs的短路光电流密度为16.67 mA•cm^-3、开路电压为0.69 V、填充因子为0.70、光电转换效率达8.08%.     

Preparation of a nanoporous CaCO3-coated TiO2 electrode and its application to a dye-sensitized solar cell

A nanoporous CaCO3 overlayer-coated TiO2 thick film was prepared by the topotactic thermal decomposition of Ca(OH)2, and its performance as an electrode of a dye-sensitized solar cell was investigated. As compared to bare TiO2, nanoporous CaCO3-coated TiO2 provided higher specific surface area and, subsequently, a larger amount of dye adsorption; this in turn increased short-circuit current (Jsc). Furthermore, the CaCO3 coating demonstrated increased impedance at the TiO2/dye/electrolyte interface and increased the lifetime of the photoelectrons, indicating the improved retardation of the back electron transfer, which increases Jsc, open-circuit voltage (Voc), and fill factor (ff). Thereby, the energy conversion efficiency (eta) of the solar cell improved from 7.8 to 9.7% (an improvement of 24.4%) as the nanoporous CaCO3 layer was coated onto TiO2 thick films.     

Composite Electrode SnO2／TiO2 for Dye-Sensitized Solar Cells

Composite nanoporous electrode SnO2/TiO2 was fabricated for the dye sensitized solar cell (DSSC) with N3 (Cis-Ru). After introducing of TiO2, the open-circuit photovoltage (Voc) was higher than that of the pure SnO2 electrode, while short-circuit photocurrent (Isc) was varied with the ratio of the TiO2. Appropriate content of the TiO2 can be beneficial to the efficiency of the solar cell, and it gives negative impact on the composite electrode when the content of TiO2 is higher.     

Computational studies on the interactions among redox couples, additives and TiO2: implications for dye-sensitized solar cells

One of the major and unique components of dye-sensitized solar cells (DSSC) is the iodide/triiodide redox couple. Periodic density-functional calculations have been carried out to study the interactions among three different components of the DSSC, i.e. the redox shuttle, the TiO(2) semiconductor surface, and nitrogen containing additives, with a focus on the implications for the performance of the DSSC. Iodide and bromide with alkali metal cations as counter ions are strongly adsorbed on the TiO(2) surface. Small additive molecules also strongly interact with TiO(2). Both interactions induce a negative shift of the Fermi energy of TiO(2). The negative shift of the Fermi energy is related to the performance of the cell by increasing the open voltage of the cell and retarding the injection dynamics (decreasing the short circuit current). Additive molecules, however, have relatively weaker interaction with iodide and triiodide.     

五甲川菁染料敏化p-NiO纳米结构电极的光电化学

研究了NiO纳米结构电极及五甲川菁染料敏化NiO纳米结构电极的光电化学行为。结果表明,NiO纳米结构电极在光照下产生阴极光电流,为p-型半导体,其禁带宽度为2.8eV,使用五甲川菁染料敏化可以显著地提高NiO纳米结构电极的阴极光电流,使NiO纳米结构电极吸收波长红移至可见光区,光电转换效率得到明显改善。研究了OTE/TiO~2/Ru(bpy)~2(SCN)~2和OTE/NiO/PMC作为光阳极和光阴极组成电池的电池特性,结果表明复合电池的光电压提高,但光电流的大小受光电流小的电极限制。     

Effects of tethering alkyl chains for amphiphilic ruthenium complex dyes on their adsorption to titanium oxide and photovoltaic properties

Ruthenium (II) complex dye, Ru(4,4'-dicarboxyl-2,2'-bipyridine)(4-nonyl-2,2'-bipyridine) (NCS)(2), (denoted as RuC9) tethering single alkyl chain was synthesized and well characterized. Its adsorption behavior onto the mesoporous TiO(2) and photovoltaic properties were compared with Z907 which has similar chemical structure but tethers two alkyl chains. RuC9 dyes tend to aggregate into vesicles in the acetonitrile/t-butanol co-solvent as a result of the amphiphilic structure, whereas Z907 dyes aggregate into lamellae. The dye-sensitized solar cell (DSSC) with RuC9 dye showed higher short-circuit photocurrent than that with Z907, attributing to its higher molar optical extinction coefficient and more adsorption amount onto the mesoporous TiO(2). However, the DSSC with Z907 dye has higher open-circuit photovoltage and power conversion efficiency, presumably due to the fact that Z907 with more alkyl chains formed a molecular layer with higher hydrophobicity. It reduced the charge recombination in the interface between the dye-sensitized mesoporous TiO(2) and electrolyte as verified by the electrochemical impedance spectroscopy and intensity modulated photocurrent and photovoltage spectroscopies.     

TiO2纳米片/巢状分级结构纳米阵列薄膜的制备及其在染料敏化太阳能电池中的应用

采用水热合成法在氟掺杂二氧化锡(FTO)导电玻璃基底上得到TiO2纳米阵列薄膜,并进一步通过NaOH溶液水热处理制备了由巢状纳米阵列及纳米片覆盖层构成的TiO2纳米阵列分级结构一体化薄膜.采用场发射扫描电镜(FE-SEM),X射线衍射(XRD),紫外-可见(UV-Vis)漫反射光谱和吸收光谱技术对TiO2薄膜的结构和性质进行表征.FE-SEM结果表明:分级结构TiO2薄膜膜厚为1.5μm,薄膜由一层纳米片覆盖层(约0.2μm高)和一层巢状纳米阵列层(约1.3μm高)组成.XRD谱图表明TiO2薄膜为锐钛矿相.UV-Vis光谱显示分级结构TiO2薄膜具有较强的光捕获能力和染料吸附能力.TiO2纳米片/巢状分级结构纳米阵列薄膜作为光阳极,可有效地提高染料敏化太阳能电池的光电转换效率,其短路电流(Jsc)为7.79mA·cm-2,开路电压(Voc)为0.80V,填充因子(FF)为0.40,光电转换效率(η)为2.48%,其光电转换效率较TiO2纳米阵列薄膜提高了近10倍.     

All-carbon electrode-based fiber-shaped dye-sensitized solar cells

A novel fiber-shaped dye-sensitized solar cell (DSSC) based on an all-carbon electrode is presented, where low-cost, highly-stable, and biocompatible carbon materials are applied to both the photoanode and the counter electrode. The fibrous carbon-based photoanode has a core-shell structure, with carbon fiber core used as conductive substrate to collect carriers and sensitized porous TiO(2) film as shell to harvest light effectively. The highly catalytic all-carbon counter electrode is made from ink carbon coatings and carbon fiber substrate. Results show that the open circuit voltage can be largely improved through engineering at the carbon fiber/TiO(2) interface. An optimized diameter of the photoanode results in an efficiency of 1.9%. It is the first demonstration of efficient DSSCs based on all-carbon electrodes, and the devices are totally free from TCOs or any other expensive electrode materials. Also, this type of solar cell is significant in obtaining bio-friendly all-carbon photovoltaics suitable for large-scale production.     

Effect of additives on the photovoltaic performance of coumarin-dye-sensitized nanocrystalline TiO2 solar cells

The effects of deoxycholic acid (DCA) and 4-tert-butylpyridine (TBP) as additives on the photovoltaic performance of coumarin-dye-sensitized nanocrystalline TiO2 solar cells were investigated. DCA coadsorption improved both the photocurrent and photovoltage of the solar cells, even though it decreased the amount of dye adsorbed on the TiO2 electrode. The improved photocurrent may arise from suppression of the deactivation of the excited state via quenching processes between dye molecules or a more negative LUMO level of the dye in the presence of DCA, resulting in a high electron-injection yield from the dye into TiO2. The increased photovoltage is probably due to suppression of recombination between the injected electrons and I3- ions on the TiO2 surface (dark current). The addition of TBP to the electrolyte also markedly improved the photovoltage and fill factor of the solar cell, and consequently, the total conversion efficiency increased from 3.6% to 7.5%. FT-IR spectroscopy indicated that a large amount of TBP was adsorbed on the dye-coated TiO2 films in the presence of Li cations. This result suggests that TBP, like DCA, suppressed the dark current on the TiO2 surface, which resulted in the improved photovoltage.     

Effect of Surface Protonation on Device Performance and Dye Stability of Dye-sensitized TiO2 Solar Cell

A flat thin TiO₂ film was employed as the photo-electrode of a dye sensitized solar cell (DSSC), on which only a geometrical mono-layer of dye was attached. The effect of sur-face protonation by HCl chemical treatment on the performance of DSSCs was studied. The results showed that the short-circuit current Jsc increased significantly upon the HCl treatment, while the open-circuit voltage Voc decreased slightly. Compared to the untreated DSSC, the Jsc and energy conversion efficiency was increased by 31% and 25%, respectively, for the 1 mol/L HCl treated cell. TiO₂ surface protonation improved electronic coupling between the chemisorbed dye and the TiO₂ surface, resulting in an enhanced electron in-jection. The decreased open-circuit voltage after TiO₂ surface protonation was mainly due to the TiO₂ conduction band edge downshift and was partially caused by increased electron recombination with the electrolyte. In situ Raman degradation study showed that the dye stability was improved after the TiO₂ surface protonation. The increased dye stability was contributed by the increased electron injection and electron back reaction with the electrolyte under the open-circuit condition.     

Double-layer coating of SrCO3/TiO2 on nanoporous TiO2 for efficient dye-sensitized solar cells

Surface modification plays a crucial role in improving the efficiency of dye-sensitized solar cells (DSSCs), but the reported surface treatments are in general superior to the untreated TiO(2) but inferior to the typical TiCl(4)-treated TiO(2) in terms of solar cell performance. This work demonstrates a two-step treatment of the nanoporous titania surface with strontium acetate [Sr(OAc)(2)] and TiCl(4) in order, each step followed by sintering. An electronically insulating layer of SrCO(3) is formed on the TiO(2) surface via the Sr(OAc)(2) treatment and then a fresh TiO(2) layer is deposited on top of the SrCO(3) layer via the TiCl(4) treatment, corresponding to a double layer of Sr(OAc)(2)/TiO(2) coated on the TiO(2) surface. As compared to the typical TiCl(4)-treated DSSC, the Sr(OAc)(2)-TiCl(4) treated DSSC improves short-circuit photocurrent (J(sc)) by 17%, open-circuit photovoltage (V(oc)) by 2%, and power conversion efficiency by 20%. These results indicate that the Sr(OAc)(2)-TiCl(4) treatment is better than the often used TiCl(4) treatment for fabrication of efficient DSSCs. Charge density at open circuit and controlled intensity modulated photocurrent/photovoltage spectroscopy reveal that the two electrodes show almost same conduction band level but different electron diffusion coefficient and charge recombination rate constant. Owing to the blocking effect of the SrCO(3) layer on electron recombination with I(3)(-) ions, the charge recombination rate constant of the Sr(OAc)(2)-TiCl(4) treated DSSC is half that of the TiCl(4)-treated DSSC, accounting well for the difference of their V(oc). The improved J(sc) is also attributed to the middle SrCO(3) layer, which increases dye adsorption and may improve charge separation efficiency due to the blocking effect of SrCO(3) on charge recombination.