锂铌比对铪铁铌酸锂晶体全息存储性能的影响

以掺杂4 mol%Hf⁴⁺的LiNbO₃:Fe:Hf系列晶体（[Li]/[Nb]比变化）为研究对象,研究了系列晶体的可见吸收光谱,在632.8nm的写入光下晶体的衍射效率、灵敏度和抗光散射能力在不同[Li]/[Nb]下的变化规律.研究发现Hf⁴⁺的浓度达到阈值浓度后,随着[Li]/[Nb]比的增大,晶体的可见吸收边会发生红移,而且晶格中[Fe²⁺]/[Fe³⁺]也会增加,这就导致随着[Li]/[Nb]比的增加,样品的衍射效率逐渐减小,写入时间缩短,灵敏度增大.同时,在晶体中,随着[Li]/[Nb]的增大,陷阱中心Fe²⁺Li数量增大会使得晶体抗光散射能力减弱.     

近化学计量比铌酸锂晶体周期极化畴反转特性研究

采用K2O作助熔剂直接拉晶法和气相输运平衡技术制备出了高质量近化学计量比铌酸锂晶体,研究了铌酸锂晶体中的[Li][Nb]比含量对其畴反转结构和极化电场的影响.实验结果表明:随着晶体中[Li][Nb]比的提高,畴极化反转电场呈明显下降趋势,使用近化学计量比铌酸锂晶体,在4.0±0.5kVmm大小极化电场条件下,成功地实现了1.0mm厚度的周期极化畴反转.并用铌酸锂晶体的Li空位缺陷模型对上述实验结果给出了合理的解释. 关键词： 近化学计量比铌酸锂晶体 周期极化 畴反转     

Mg2+对Fe∶LiNbO3晶体光折变响应时间的影响

在 Fe∶Li Nb O3 中掺进 3 mol%和 6mol% Mg O,生长了 Mg∶Fe∶L i Nb O3 晶体 .测试了 Mg∶Fe∶Li Nb O3 晶体抗光致散射能力、衍射效率、响应时间和光电导 .推导响应时间与光电导之间的关系 .在 Fe∶Li Nb O3 晶体中掺进 6mol%的 Mg2 + ,它的抗光致散射能力比Fe∶L i Nb O3 晶体提高一个数量级 ,响应速度比 Fe∶Li Nb O3 晶体提高四倍     

Improvement of photorefractive properties in Hf:Fe:LiNbO3 crystals with various [Li]/[Nb] ratios

Photorefractive properties of Hf:Fe:LiNbO3 crystals with various [Li]/[Nb] ratios have been investigated at 488 nm wavelength based on the two-wave coupling experiment. High diffraction efficiency and large recording sensitivity are observed and explained. The decrease in Li vacancies is suggested to be the main contributor to the increase in the photoconductivity and subsequently to the induction of the improvement of recording sensitivity. The saturation diffraction efficiency is measured up to 80.2%, and simultaneously the recording sensitivity of 0.91 cm/J is achieved to in the Hf:Fe:LiNbO3 crystal grown from the melt with the [Li]/[Nb] ratio of 1.20, which is significantly enhanced as compared with those of the Hf:Fe:LiNbO3 crystal with the [Li]/[Nb] ratio of 0.94 in melt under the same experimental conditions. Experimental results definitely show that increasing the [Li]/[Nb] ratio in crystal is an effective method for Hf:Fe:LiNbO3 crystal to improve its photorefractive properties.     

铜铁镁三掺铌酸锂晶体的第一性原理研究

利用基于密度泛函理论的第一性原理,研究了Cu:Fe:Mg:LiNbO3晶体及对比组的电子结构和光学特性.研究显示,单掺铜或铁铌酸锂晶体的杂质能级分别由Cu 3d轨道或Fe 3d轨道贡献,禁带宽度分别为3.45和3.42 eV;铜、铁共掺铌酸锂晶体杂质能级由Cu和Fe的3d轨道共同贡献,禁带宽度为3.24 eV,吸收峰分别在3.01,2.53和1.36 eV处;Cu:Fe:Mg:LiNbO3晶体中Mg^2+浓度低于阈值或高于阈值(阈值约为6.0 mol%)的禁带宽度分别为2.89 eV或3.30 eV,吸收峰分别位于2.45 eV,1.89 eV或2.89 eV,2.59 eV,2.24 eV.Mg^2+浓度高于阈值,会使吸收边较低于阈值情况红移;并使得部分Fe^3+占Nb位,引起晶体场改变,从而改变吸收峰位置和强度.双光存储应用中可选取2.9 eV作为擦除光,2.5 eV作为读取和写入光,选取Mg^2+浓度达到阈值的三掺晶体在增加动态范围和灵敏度等参量以及优化再现图像的质量等方面更具优势.     

坩埚下降法生长的LiNbO_3,Fe∶LiNbO_3,Zn∶Fe∶LiNbO_3单晶的吸收光谱特性

用紫外可见光谱 (UV/VisibleSpectra)测试并研究了坩埚下降法生长的LiNbO3 、Fe∶LiNbO3 ,以及Zn∶Fe∶LiN bO3 晶体的吸收特性。分析了产生这些吸收特性的原因以及与工艺生长方法的内在联系。研究结果表明 :LiNbO3 单晶沿晶体生长方向 ,其紫外吸收边向长波方向移动 ,且在 35 0～ 4 5 0nm波段的吸收也逐渐增大 ,这是由于Li的分凝与挥发 ,逐渐产生缺锂所造成的 ;在Fe∶LiNbO3 单晶中观察到Fe2 + 离子在 4 80nm附近的特征吸收峰 ,并发现沿生长方向 ,Fe2 + 离子的浓度逐渐增加 ,这与提拉法生长得到的晶体不同 ;在Fe∶LiNbO3 单晶中掺入质量分数为 1.7%ZnO后 ,吸收边位置发生蓝移 ,而掺杂质量分数达到 3.4 %时 ,观察到有红移现象。Fe2 + 离子在Zn∶Fe∶LiNbO3 单晶中的浓度与ZnO掺杂量有密切关系。在掺杂质量分数 1.7%ZnO的Fe∶LiNbO3 单晶中 ,Fe2 + 离子从底部到顶部的浓度变化比在掺杂质量分数 3.4 %ZnO晶体中大 ,这是由于Zn2 + 抑制Fe2 + 离子进入Li位的能力随掺杂量的增加而逐渐减弱造成的。就该下降法工艺技术对Fe2 + 离子在晶体中的浓度分布的影响作了分析     

非化学计量比铌酸钾锂晶体的光谱特征

用顶部籽晶法生长了一批不同组成的铌酸钾锂晶体。利用近红外cw: Ti-sapphire激光研究了三种组成的经过精细抛光的晶体样品的二次谐波性质,结果表明晶体的二次谐波效应与晶体组成密切相关,Li含量越高的样品倍频效率越高。利用红外Raman光谱技术调查了晶体非线性晶格振动特征,分析了晶体中组分离子浓度对晶体红外Raman光谱特征的影响,探讨了组分离子对晶体二次谐波性质影响的原因。结果表明,晶体中位于C格位的Li离子浓度对晶体Raman光谱产生了强烈的影响,低Li含量晶体中[NbO₆]7-八面体所对应的3个Raman特征光谱线没有峰发生分裂;当晶体中Li离子浓度增加时,ν₅所对应的Raman峰有所加宽,ν₂振动模式出现分裂峰,并在100～400 cm-1范围出现小峰数量增多;当Li离子浓度接近铁电相边界时,[NbO₆]7-八面体结构接近解体,ν₅所对应的Raman峰分裂成3个峰,ν₁和ν₂振动模式发生部分分裂,在100～400 cm-1范围小峰更为突出。这些影响的本质在于晶体中Li含量的提高导致晶体中[NbO₆]7-八面体畸变程度加大,与晶体非线性光学性质相一致。     

掺杂对铌酸锂晶体非挥发全息存储性能的影响

通过研究掺镁、掺锌和掺铟同成分铌酸锂晶体的紫外-红光双色全息存储性能,发现双色记录响应时间均比单色记录时明显缩短,最多的可减小3个数量级;双色记录灵敏度大幅度提高,在掺镁5 mol.%的晶体中可达到11 cm/J.在掺杂浓度超过抗光损伤阈值的铌酸锂晶体中,均可实现非挥发全息存储.但是,在掺镁、锌样品中,深、浅能级中心上的光栅反相,而在掺铟样品中则表现为同相.这是由于掺杂离子的种类不同,在铌酸锂晶体中形成的缺陷中心也不同所引起的. 关键词： 掺杂 铌酸锂晶体 非挥发 全息存储     

同成分掺镁铌酸锂晶体紫外光致吸收阈值效应的研究

研究了同成分掺镁铌酸锂晶体中的紫外光致吸收效应。通过对不同掺Mg浓度铌酸锂晶体的紫外光致吸收系数和双色存储灵敏度的测量,发现同成分掺镁铌酸锂晶体的紫外光致吸收效应具有Mg离子浓度阈值效应。只有当掺Mg摩尔分数大于3．0％时,从近紫外一直延伸到近红外波段的紫外光致吸收效应才显示出来。这一Mg离子浓度阈值效应进一步为双色存储灵敏度的测量结果所证实。该浓度阈值小于掺镁铌酸锂晶体抗光损伤效应的摩尔分数阈值4．6％。这种紫外光致吸收现象可能和掺镁铌酸锂晶体中反位铌NbLi浓度的急剧减少基本消失有关。     

利用铌酸锂晶体制作体全息光栅的设计性实验

利用双光束干涉,通过控制双光束的记录角度,在铌酸锂晶体中写入光折变体全息布拉格光栅.将该光栅应用于光通信系统中作为滤波器使用,利用ASE光源和光谱仪对其进行测试,在1 548nm波长处获得了峰值半高全宽为4nm,衍射效率为10%的滤波效果.     

Acoustic cavitation series: part one: Acoustic cavitation: an introduction

Acoustic cavitation has been an active area of research for at least 30 years and interest in the subject shows no sign of diminishing. Cavitation may occur whenever high intensity ultrasound is applied to liquids, for example in such important applications as sonar, industrial processing and bio-medical research. Future issues will carry a series of articles reviewing the physics and technology of acoustic cavitation, each contributed by a well-known specialist. The present introductory article is a preface to the series, covering background history, explaining the scope of the subject and defining terms in common use. Also included is a list of the major sources of reference presently available, in the form of books, reviews and collections of papers.     

The radiothermoluminescence of (ZnS:CdS:Ag:Ni:Co) phosphors irradiated with beta-rays

The radiothermoluminescence characteristics have been studied for a number of (ZnS:CdS::Ag:Ni:Co) phosphors, with various cobalt impurity contents, after exposure to⁹⁰Sr beta-rays at room temperature. Thermoluminescent spectra show a peak wavelength of 7000 Å, which remains unchanged with increase in cobalt concentration. Thermoluminescence curves exhibit a single well-defined peak appearing at temperatures far above room temperature. This peak shifts to lower temperatures with increasing cobalt content. The relation between thermoluminescence response and dose is linear over the dose range of 1 to 500 rads. Thermoluminescence measurements made after storing the irradiated phosphor for 48 hours in dark have revealed an information loss of 4% over this storage period. The radiothermoluminescence characteristics, storage capacity and storage stability of these sulphide phosphors compete reasonably with those of lithium fluoride over the dose range of 1 rad to 500 rads.     

Er:YCOB和Er:Yb:YCOB晶体的光谱分析

分别测量了Er YCOB晶体和ErYb YCOB晶体的室温吸收光谱.讨论了Yb3+离子对Er3+离子的敏化作用.     

Fourier transform profilometry: : a review

Fourier transform profilometry is one of the popular non-contact 3-D measurement methods, where a Ronchi grating or sinusoidal grating is projected onto a diffuse three-dimensional surface, and the resulting deformed grating image is detected by a CCD camera and processed by a computer. This method requires only one frame (or two frames) of the deformed fringe pattern in some algorithms to retrieve the surface of measured object, so it has obvious advantage for real time data acquisition and 3-D measurement of dynamic process. In this paper, we review some algorithms in FTP, discuss some important problems, including frequency spectra overlapping, phase unwrapping, sampling, and 3-D measurement of dynamic process. With the development of computer hardware and software and availability of high-resolution image grabber, FTP method will be a promising one for acquiring 3-D data of object, and more and more researchers pay attention to it.     

LiNbO_3:In:Fe:Cu晶体中的双波长非易失存储

为了提高晶体的非易失存储性能,采用双波长存储技术实验研究了LiNbO3:In:Fe:Cu晶体中的非易失存储,折射率调制度为1.04×10-4,记录灵敏度达到0.965 cm/J.与传统的双色非易失记录相比,该方法大幅度地提高了光栅的强度和记录的灵敏度.利用Kukhtarev带输运模型对双波长非易失记录过程中光栅的动态演化过程进行了数值模拟,同时讨论了氧化还原程度对双波长非易失全息记录的影响.理论与实验符合的较好.