Study of phase equilibria established up to the solidus line in the system Fe2V4O13−WO3

The phase equilibria established up to the solidus line in the system Fe₂V₄O₁₃−WO₃, one of the intersections of the three-component system Fe₂O₃−V₂O₅−WO₃, have been studied. The system appears not to be a real two-component system.

---

Zusammenfassung Es wurde eine Untersuchung des Phasengleichgewichtes durchgeführt, welches bezüglich der Solidus-Linie im System Fe₂V₄O₁₃−WO₃, einer der Zwischenbereiche im Dreikomponentensystem Fe₂O₃−V₂O₅−WO₃, nachgewiesen wurde. Dieses System scheint kein echtes Zweikomponentensystem zu sein.

     

Bi2WO6/TiO2纳米管异质结构复合材料的多模式下的光催化活性比较

以TiO₂纳米管为模板,采用多组分自组装结合水热法制备Bi₂WO₆/TiO₂纳米管异质结构复合材料。通过多种技术如X射线衍射（XRD）,X射线光电子能谱（XPS）,N₂吸附-脱附,扫描电镜（SEM）,高分辨透射电镜（HRTEM）和紫外可见漫反射吸收光谱（UV-Vis DRS）考察所制备样品的组成、结构、形貌、光吸收和电子性质。Bi₂WO₆纳米片或纳米粒子分布在TiO₂纳米管上,形成异质结构。随后,通过在紫外、可见和微波辅助光催化模式下降解染料罗丹明B（RhB）来评价复合催化剂的光催化活性。与TiO₂纳米管和Bi₂WO₆相比,Bi₂WO₆/TiO₂-35纳米管在多模式下表现出更优异的光催化活性。与紫外和可见降解模式相比,Bi₂WO₆/TiO₂-35纳米管在微波辅助光催化模式下对RhB的降解效率最高。这种增强的光催化活性源于适量Bi₂WO₆的引入、纳米管独特的形貌特征和降解模式所引起的增强的量子效率。降解过程中的活性物种被证明是h⁺,·OH和·O₂^-自由基。而且,在微波辅助光催化模式下,可产生更多的·OH和·O₂^-自由基。     

Selective catalytic reduction of NO with CO on Pt/W–Ce–Zr catalysts

Various Pt catalysts (Pt/ZrO₂, Pt/CeO₂, Pt/CeZrO, Pt/WO₃/ZrO₂ and Pt/WO₃/CeZrO) were prepared and characterized, and their catalytic reduction reactions of NO by CO, with or without the presence of excess oxygen, were investigated. The results of temperature-programmed experiments showed that CO could be easily oxidized over Pt/CeO₂ and Pt/CeZrO while the introduction of WO₃ into the catalyst (Pt/WO₃/CeZrO) inhibited the reduction of catalyst surface; NO could not dissociate over those catalysts in oxidized state but after CO reduction at a low temperature, NO dissociation took place only over Pt/CeO₂ and Pt/CeZrO catalysts. For NO + CO reaction, those easily reduced catalysts Pt/CeO₂ and Pt/CeZrO exhibited better catalytic performances, and NO could be rapidly converted below 350 °C. For the reaction with the presence of excess O₂, the NO conversions were significantly inhibited, but better NO conversions were obtained over the tungstate-contained catalysts when compared with Pt/CeO₂ and Pt/CeZrO. The higher activities of Pt/W–Ce–Zr catalysts were attributed to their high acidities.     

Influence of support acidity on electronic state of platinum in oxide systems promoted by SO4 2− anions

The electronic state of platinum supported on SO₄/ZrO₂, SO₄/TiO₂, SO₄/Al₂O₃, and SO₄/SiO₂ systems and on systems unpromoted by sulfur was investigated by diffuse-reflectance IR spectroscopy using CO as the probe molecule. The introduction of SO₄ ²⁻ anions increases the electron deficit on platinum particles. This suppresses the formation of bridging CO complexes with the metal, leads to the high-frequency shift of absorption maxima of CO adsorbed in the linear form, and stabilizes positively charged metal species (Pt^δ+ and Pt⁺) during the reduction process. The formation of the positively charged species includes the interaction between the acidic protons and the metal particles yielding [Pt−H]^δ+ adducts. The extent of the influence of the support on the electronic state of the metal increases in the series SO₄/SiO₂<SO₄/Al₂O₃<SO₄/TiO₂<SO₄/ZrO₂ in parallel with an increase in the strength of the acid sites in the system. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 6, pp. 1094–1099, June, 1998.     

Acidic properties of V2O5-WO3/ZrO2 catalysts

The adsorption of pyridine on V₂O₅−WO₃/ZrO₂ has been studied by FTIR. In V₂O₅/ZrO₂ (2 wt.%), the number of both Br?nsted and Lewis acidic sites increased with the addition of WO₃, while in V₂O₅/ZrO₂ (5 wt.%), Br?nsted sites increased and Lewis sites did not change.     

Preparation and characterization of nanotube Li-Ti-O by molten salt method

Nanotube Li-Ti-O compound with high surface (198.6 m²·g⁻¹) was prepared by a method involving the treatment of nanotube Na₂Ti₂O₅·H₂O in molten LiNO₃ and characterization by means of transmission electron microscopy (TEM), energy-dispersive spectra (EDS), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and thermogravimetry-differential thermal analysis (TG/DTG). Results show that the nanotube Li-Ti-O compound prepared by this method involves two crystal phases: spinel Li₂Ti₂O₄ and anatase Li_xTiO₂ (x < 0.1). Li⁺ exhibits different Li1s binding energy in the two crystal phases. In ambient air, the Li-Ti-O compound adsorbs water easily, and the chemically adsorbed water is difficult to remove below 400°C. Translated from Chinese Journal of Inorganic Chemistry, 2006, 22(12): 2135–2139 [译自: 无机化学学报]     

Synthesis and spectral properties of titanium(iv) polynuclear hydroxo complexes stabilized in solution by the [PW11O39]7− heteropolyanion

Unsaturated heteropolyanions (HPA) [PW₁₁O₃₉]⁷⁻ stabilize Ti^IV hydroxo complexes in aqueous solutions (Ti: PW₁₁ [PW₁₁O₃₉]⁷⁻⪯12, pH 1–3). Spectral studies (optical,¹⁷O and³¹P NMR, and IR spectra) and studies by the differential dissolution method demonstrated that Ti^IV hydroxo complexes are stabilized through interactions of polynuclear Ti^IV hydroxo cations with heteropolyanions [PW₁₁TiO₄₀ ⁵⁻ formed. Depending on the reaction conditions, hydroxo cations Ti _n−1O _x H _y ^m+ either add to oxygen atoms of the W−O−Ti bridges of the heteropolyanions to form the complex [PW₁₁TiO₄₀·Ti _n−1O _x H _y ] ^k− (at [HPA]=0.01 mol L⁻¹) or interact with Ti^IV of the heteropolyanions through the terminal o atom to give the polynuclear complexes [PW₁₁O₃₉Ti−O−Ti _n−1O _x H _y ]^q− (at [HPA]=0.2 mol L⁻¹). When the complexes of the first type were treated with H₂O₂, Ti^IV ions added peroxo groups. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 5, pp. 914–920, May, 1997.     

Detection of liquid petroleum gas using mixed nanosized tungsten oxide-based thick-film semiconductor sensor

The thick-film semiconductor sensor for liquid petroleum gas (LPG) detection was fabricated using a mixed WO₃-based sensor. We present the characterization of both their structural properties by means of XRD measurements and the electrical characteristics by using gas-sensing properties. The sensing characteristics such as sensitivity, working range, cross-sensitivity and response time were studied by using nanosized WO₃-based mixed with different metal oxides (SnO₂, TiO₂ and In₂O₃) and doped with noble metals (Au, Pd and Pt). The WO₃-based mixed with 5 wt.% In₂O₃ and 0.5 wt.% Pd showed the higher sensing characteristic at low concentration of LPG sensor at an operating temperature 225 °C.     

Electrochemical synthesis of Fe3O4-PB nanoparticles with core-shell structure and its electrocatalytic reduction toward H2O2

The Fe₃O₄-Prussian blue (PB) nanoparticles with core-shell structure have been in situ prepared directly on a nano-Fe₃O₄-modified glassy carbon electrode by cyclic voltammetry (CV). First, the magnetic nano-Fe₃O₄ particles were synthesized and characterized by X-ray diffraction. Then, the properties of the Fe₃O₄-PB nanoparticles were characterized by CV, electrochemical impedance spectroscopy, and superconducting quantum interference device. The resulting core-shell Fe₃O₄-PB-modified electrode displays a dramatic electrocatalytic ability toward H₂O₂ reduction, and the catalytic current was a linear function with the concentration of H₂O₂ in the range of 1 × 10⁻⁷~5 × 10⁻⁴ mol/l. A detection limit of 2 × 10⁻⁸ (s/n = 3) was determined. Moreover, it showed good reproducibility, enhanced long-term stability, and potential applications in fields of magnetite biosensors.     

Sol-gel electrochromic device

All solid state electrochromic devices have potential applications in architectural and automotive fields to regulate the transmission and reflection of radiant energy. We present the optical and electrochemical characteristics of two solid state windows having the configuration glass/ITO/TiO₂-CeO₂/TiO₂/TiO₂-CeO₂/ITO/glass and glass/ITO/WO₃/TiO₂/TiO₂-CeO₂/ITO/glass where the three internal layers have been prepared by sol gel methods. The preparation of the individual sols and some physical properties of the different sol gel coatings are reported.     

Detection of nitrogen dioxide using mixed tungsten oxide-based thick film semiconductor sensor

The thick film semiconductor sensor for NO₂ gas detection was fabricated by screen-printing method using a mixed WO₃-based as sensing material. The sensing characteristics, such as response time, response linearity, sensitivity, working range, cross sensitivity, and long-term stability were further studied by using a WO₃-based mixed with different metal oxides (SnO₂, TiO₂ and In₂O₃) and doped with noble metals (Au, Pd and Pt) as sensing materials was observed. The highest sensitivity for low concentrations (<16 mg l⁻¹) was observed using WO₃-based mixed with In₂O₃ or TiO₂. The NO₂ gas sensor showing the fastest response and recovery time (both within 2 min), good linearity (Y=0.606X+0.788 R²=0.991) for gas concentrations from 3 to 310 mg l⁻¹, low resistance (3 MΩ), high sensitivity, undesirable cross sensitivity effect and good long-term stability (at least 120 days) using WO₃-SnO₂-Au as sensing material.     

Osmotic Coefficients of the Li<Subscript>2</Subscript>B<Subscript>4</Subscript>O<Subscript>7</Subscript>+LiCl + H<Subscript>2</Subscript>O System at <Emphasis Type="Italic">T</Emphasis>=273.15 K

Osmotic coefficients and water activities for the Li₂B₄O₇+LiCl+H₂O system have been measured at T=273.15 K by the isopiestic method, using an improved apparatus. Two types of osmotic coefficients, φ _S and φ _E, were determined. φ _S is based on the stoichiometric molalities of the solute Li₂B₄O₇(aq), and φ _E is based on equilibrium molalities from consideration of the equilibrium speciation into H₃BO₃,B(OH)₄⁻ and B₃O₃(OH)₄⁻. The stoichiometric equilibrium constants K _m for the aqueous speciation reactions were estimated. Two types of representations of the osmotic coefficients for the Li₂B₄O₇+LiCl+H₂O system are presented with ion-interaction models based on Pitzer’s equations with minor modifications: model (I) represents the φ _S data with six parameters based on considering the ion-interactions between three ionic species of Li⁺, Cl⁻, and B₄O₇²⁻, and model (II) for represents the φ _E data based on considering the equilibrium speciation. The parameters of models (I) and (II) are presented. The standard deviations for the two models are 0.0152 and 0.0298, respectively. Model (I) was more satisfactory than model (II) for representing the isopiestic data.     

Effect of ionic interactions on the rates of reduction of Cu(II) with H2O2 in aqueous solutions

The rates of reduction of Cu(II) with H₂O₂ have been measured in NaCl and NaBr solutions and mixtures with NaClO₄ as a function of pH (6 to 9), temperature (5 to 45°C) and ionic composition (0.1 to 6M). The effect of pH on the rates was found to be independent of temperature and ionic composition. The rates increased as a function of [H⁺] raised to the power of 1.3 to 1.6. Speciation calculations indicate that this pH dependence can be attributed to Cu(OH)₂ being the reactive species. The rate constants in NaCl and NaBr and mixtures with NaClO₄ were independent of ionic strength, but proportional to the halide concentration raised to the power of 2.0 (0.2 to 2.6M). These results can be attributed to Cu(OH)₂Cl ₂ ²⁻ being the reactive species to reduction with H₂O₂. The Cu(I) halide complexes formed from the reduction are not easily oxidized with O₂ or H₂O₂. The faster rates in Br⁻ solutions, which form stronger complexes with Cu⁺, support this contention. Measurements made in NaCl with added NaHCO₃, NaB(OH)₄ EDTA, NTA and glycine were also made. These measurements indicate that the CuL complexes (L=B(OH) ₄ ⁻ , CO ₃ ²⁻ , EDTA, NTA, and glycine) are not very reactive to reduction with H₂O₂. The addition of Mg²⁺ or Ca²⁺ caused the rates to increase due to the formation of MgL or CaL complexes and the resultant release of reactive Cu²⁺.     

Large cation model of dissociative reduction of electrochromic WO3−x films

Studies of dissociative reduction processes of electrochromic WO_3−x films were conducted to: (i) evaluate their utility for electroetching and (ii) determine their fundamental mechanistic features to reduce or eliminate their occurrence in normal optical switching and modulation operation of WO_3−x films. We have found that while the small intercalating cations stabilize WO_3−x structure, the large nonintercalating surfactant cations (Et₄N+, CtMe₃N+) contribute to the dissociative reduction. While these cations do not affect WO_3−x structure of anodically protected films (E > 0.2 V), they cause surface lattice polarization on electron injection to the conduction band of WO_3−x at lower electrode potentials, in the absence of intercalating cations. We have found that this process is limited to the surface and no structural damage occurs to the underlying film. The mechanistic aspects of the process have been discussed on the basis of experimental voltammetric and electrochemical quartz crystal nanogravimetric (EQCN) measurements and ab initio quantum mechanical calculations.      

Pyrochlore formation, phase relations, and properties in the CaO-TiO2-(Nb,Ta)2O5 systems

Phase equilibria studies of the CaO:TiO₂:Nb₂O₅ system confirmed the formation of six ternary phases: pyrochlore (A₂B₂O₆O′), and five members of the (110) perovskite-slab series Ca_n(Ti,Nb)_nO_3n+2, with n=4.5, 5, 6, 7, and 8. Relations in the quasibinary Ca₂Nb₂O₇−CaTiO₃ system, which contains the Ca_n(Ti,Nb)_nO_3n+2 phases, were determined in detail. CaTiO₃ forms solid solutions with Ca₂Nb₂O₇ as well as CaNb₂O₆, resulting in a triangular single-phase perovskite region with corners CaTiO₃-70Ca₂Ti₂O₆:30Ca₂Nb₂O₇-80CaTiO₃:20CaNb₂O₆. A pyrochlore solid solution forms approximately along a line from 42.7:42.7:14.6 to 42.2:40.8:17.0 CaO:TiO₂:Nb₂O₅, suggesting formulas ranging from Ca_1.48Ti_1.48Nb_1.02O₇ to Ca_1.41Ti_1.37Nb_1.14O₇ (assuming filled oxygen sites), respectively. Several compositions in the CaO:TiO₂:Ta₂O₅ system were equilibrated to check its similarity to the niobia system in the pyrochlore region, which was confirmed. Structural refinements of the pyrochlores Ca_1.46Ti_1.38Nb_1.11O₇ and Ca_1.51Ti_1.32V_0.04Ta_1.10O₇ using single-crystal X-ray diffraction data are reported (Fd3m (#227), a=10.2301(2) Å (Nb), a=10.2383(2) Å (Ta)), with Ti mixing on the A-type Ca sites as well as the octahedral B-type sites. Identical displacive disorder was found for the niobate and tantalate pyrochlores: Ca occupies the ideal 16d position, but Ti is displaced 0.7 Å to partially occupy a ring of six 96g sites, thereby reducing its coordination number from eight to five (distorted trigonal bipyramidal). The O′ oxygens in both pyrochlores were displaced 0.48 Å from the ideal 8b position to a tetrahedral cluster of 32e sites. The refinement results also suggested that some of the Ti in the A-type positions may occupy distorted tetrahedra, as observed in some zirconolite-type phases. The Ca-Ti-(Nb,Ta)-O pyrochlores both exhibited dielectric relaxation similar to that observed for some Bi-containing pyrochlores, which also exhibit displacively disordered crystal structures. Observation of dielectric relaxation in the Ca-Ti-(Nb,Ta)-O pyrochlores suggests that it arises from the displacive disorder and not from the presence of polarizable lone-pair cations such as Bi³⁺.     

Effect of sintering on the ionic conductivity of garnet-related structure Li5La3Nb2O12 and In- and K-doped Li5La3Nb2O12

Garnet-structure related metal oxides with the nominal chemical composition of Li₅La₃Nb₂O₁₂, In-substituted Li_5.5La₃Nb_1.75In_0.25O₁₂ and K-substituted Li_5.5La_2.75K_0.25Nb₂O₁₂ were prepared by solid-state reactions at 900, 950, and 1000 °C using appropriate amounts of corresponding metal oxides, nitrates and carbonates. The powder XRD data reveal that the In- and K-doped compounds are isostructural with the parent compound Li₅La₃Nb₂O₁₂. The variation in the cubic lattice parameter was found to change with the size of the dopant ions, for example, substitution of larger In³⁺(r_CN6: 0.79 Å) for smaller Nb⁵⁺ (r_CN6: 0.64 Å) shows an increase in the lattice parameter from 12.8005(9) to 12.826(1) Å at 1000 °C. Samples prepared at higher temperatures (950, 1000 °C) show mainly bulk lithium ion conductivity in contrast to those synthesized at lower temperatures (900 °C). The activation energies for the ionic conductivities are comparable for all samples. Partial substitution of K⁺ for La³⁺ and In³⁺ for Nb⁵⁺ in Li₅La₃Nb₂O₁₂ exhibits slightly higher ionic conductivity than that of the parent compound over the investigated temperature regime 25-300 °C. Among the compounds investigated, the In-substituted Li_5.5La₃Nb_1.75In_0.25O₁₂ exhibits the highest bulk lithium ion conductivity of 1.8×10⁻⁴ S/cm at 50 °C with an activation energy of 0.51 eV. The diffusivity (“component diffusion coefficient”) obtained from the AC conductivity and powder XRD data falls in the range 10⁻¹⁰-10⁻⁷ cm²/s over the temperature regime 50-200 °C, which is extraordinarily high and comparable with liquids. Substitution of Al, Co, and Ni for Nb in Li₅La₃Nb₂O₁₂ was found to be unsuccessful under the investigated conditions.     

Highly Dispersed Ce x Zr1−x O2 Nano-Oxides Over Alumina, Silica and Titania Supports for Catalytic Applications

We have been exploring the utilization of supported ceria and ceria–zirconia nano-oxides for different catalytic applications. In this comprehensive investigation, a series of Ce _x Zr_1−x O₂/Al₂O₃, Ce _x Zr_1−x O₂/SiO₂ and Ce _x Zr_1−x O₂/TiO₂ composite oxide catalysts were synthesized and subjected to thermal treatments from 773 to 1073 K to examine the influence of support on thermal stability, textural properties and catalytic activity of the ceria–zirconia solid solutions. The physicochemical characterization studies were performed using X-ray diffraction (XRD), Raman spectroscopy (RS), X-ray photoelectron spectroscopy (XPS), and high-resolution transmission electron microscopy (HREM), thermogravimetry and BET surface area methods. To evaluate the catalytic properties, oxygen storage/release capacity (OSC) and CO oxidation activity measurements were carried out. The XRD analyses revealed the formation of Ce_0.75Zr_0.25O₂, Ce_0.6Zr_0.4O₂, Ce_0.16Zr_0.84O₂ and Ce_0.5Zr_0.5O₂ phases depending on the nature of support and calcination temperature employed. Raman spectroscopy measurements in corroboration with XRD results suggested enrichment of zirconium in the Ce _x Zr_1−x O₂ solid solutions with increasing calcination temperature thereby resulting in the formation of oxygen vacancies, lattice defects and oxygen ion displacement from the ideal cubic lattice positions. The HREM results indicated a well-dispersed cubic Ce _x Zr_1−x O₂ phase of the size around 5 nm over all supports at 773 K and there was no appreciable increase in the size after treatment at 1073 K. The XPS studies revealed the presence of cerium in both Ce⁴⁺ and Ce³⁺ oxidation states in different proportions depending on the nature of support and the treatment temperature applied. All characterization techniques indicated absence of pure ZrO₂ and crystalline inactive phases between Ce–Al, Ce–Si and Ce–Ti oxides. Among the three supports employed, silica was found to stabilize more effectively the nanosized Ce _x Zr_1−x O₂ oxides by retarding the sintering phenomenon during high temperature treatments, followed by alumina and titania. Interestingly, the alumina supported samples exhibited highest OSC and CO oxidation activity followed by titania and silica. Details of these findings are consolidated in this review.     

Chemiluminescence in O2 oxidation of organosodium compounds of polycyclic aromatic hydrocarbons and benzophenone

Chemiluminescence (CL) in oxidation of organosodium compounds by O₂ in THF was studied. Emitters of CL are excited complexes of polycyclic aromatic hydrocarbons, excimers¹(R·R)^*. The mechanism of their formation was proposed. The Na⁺, R^.−+O₂ CL system is a unique source for the selective generation of excimers of aromatic hydrocarbons. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 2, pp. 284–288, February, 1997.     

Phase formation, crystal chemistry, and properties in the system Bi2O3-Fe2O3-Nb2O5

Subsolidus phase relations have been determined for the Bi₂O₃-Fe₂O₃-Nb₂O₅ system in air (900-1075 °C). Three new ternary phases were observed—Bi₃Fe_0.5Nb_1.5O₉ with an Aurivillius-type structure, and two phases with approximate stoichiometries Bi₁₇Fe₂Nb₃₁O₁₀₆ and Bi₁₇Fe₃Nb₃₀O₁₀₅ that appear to be structurally related to Bi₈Nb₁₈O₅₇. The fourth ternary phase found in this system is pyrochlore (A₂B₂O₆O′), which forms an extensive solid solution region at Bi-deficient stoichiometries (relative to Bi₂FeNbO₇) suggesting that ≈4-15% of the A-sites are occupied by Fe³⁺. X-ray powder diffraction data confirmed that all Bi-Fe-Nb-O pyrochlores form with positional displacements, as found for analogous pyrochlores with Zn, Mn, or Co instead of Fe. A structural refinement of the pyrochlore 0.4400:0.2700:0.2900 Bi₂O₃:Fe₂O₃:Nb₂O₅ using neutron powder diffraction data is reported with the A cations displaced (0.43 Å) to 96g sites and O′ displaced (0.29 Å) to 32e sites (Bi_1.721Fe_0.190(Fe_0.866Nb_1.134)O₇, Fd3¯m (#227), ). This displacive model is somewhat different from that reported for Bi_1.5Zn_0.92Nb_1.5O_6.92, which exhibits twice the concentration of small B-type cations on the A-sites as the Fe system. Bi-Fe-Nb-O pyrochlores exhibited overall paramagnetic behavior with large negative Curie-Weiss temperature intercepts, slight superparamagnetic effects, and depressed observed moments compared to high-spin, spin-only values. The single-phase pyrochlore with composition Bi_1.657Fe_1.092Nb_1.150O₇ exhibited low-temperature dielectric relaxation similar to that observed for Bi_1.5Zn_0.92Nb_1.5O_6.92; at 1 MHz and 200 K the relative permittivity was 125, and above 350 K conductive effects were observed.     

Isopiestic Determination of the Osmotic Coefficients and Pitzer Model Representation for the Li<Subscript>2</Subscript>B<Subscript>4</Subscript>O<Subscript>7</Subscript>+LiCl + H<Subscript>2</Subscript>O System at <Emphasis Type="Italic">T</Emphasis>=298.15 K

Isopiestic molalities and water activities have been measured for the Li₂B₄O₇+LiCl + H₂O system at T=298.15 K using an improved isopiestic apparatus. Two types of osmotic coefficients, φ _S and φ _E, were determined, where φ _S is based on the stoichiometric molalities of the solute Li₂B₄O₇(aq) and φ _E is based on equilibrium molalities calculated by consideration of the equilibrium speciation of Li₂B₄O₇ to partially form H₃BO₃, B(OH)₄⁻ and B₃O₃(OH)₄⁻. The stoichiometric equilibrium constant K _m for the aqueous speciation reaction was estimated. Two representations of the osmotic coefficients of Li₂B₄O₇ + LiCl + H₂O were made with Pitzer’s ion-interaction model. Model (1) involved representing the φ _S values with six parameters based on considering the ionic interactions between Li⁺, Cl⁻, and B₄O₇²⁻; and model (2) involved representing the φ _E values based on the calculated equilibrium speciation. Reasonable agreements were obtained between the experimental osmotic coefficient data and those calculated using the above models, with standard deviations of 0.075 and 0.0229, respectively, for these two models. The thermodynamic osmotic coefficients for the complex system containing polymeric boron anions and lithium cation was modelled and explained by use of Pitzer’s ion-interaction model, with minor modifications in combination with speciation reaction equilibria.