Synchrotron SAXS and WAXS Studies on Changes in Structural and Thermal Properties of Poly[(R)‐3‐hydroxybutyrate] Single Crystals during Heating

Summary: The annealing and melting behavior of poly[(R)‐3‐hydroxybutyrate] (P(3HB)) single crystals were followed in real time by synchrotron small‐ (SAXS) and wide‐angle X‐ray scattering (WAXS) measurements. The real‐time SAXS measurements revealed that the P(3HB) single crystal exhibits a discontinuous increase of lamellar thickness during heating. The structural changes as observed by SAXS and WAXS were in response to the thermal properties of single crystals characterized by differential scanning calorimetry.

A series of two‐dimensional small‐angle X‐ray scattering patterns of P(3HB) single crystal mats during the lamellar thickening process.     

Glass transition and melting behavior of poly(ether-ester) multiblock copolymers with poly(tetramethylene isophthalate) hard segments

The glass transition and melting behavior of poly(ether-ester) multiblock copolymers with poly(tetramethylene isophthalate) (PTMI) hard segments and poly(tetramethylene oxide) (PTMO) soft segments are studied by differential scanning calorimetry (DSC) and small- and wide-angle x-ray scattering (SAXS and WAXS). Thermodynamic melting parameters for the PTMI homopolymer are estimated by WAXS and from the dependence of melting point on crystallization temperature. The melting behavior of PTMI is characterized by dual endotherms which are qualitatively representative of the original morphology, although reorganization effects are present. The composition dependence of the glass transition temperature parameters after rapid quenching from the melt are well described by mixed phase correlations for copolymers in the range 30-100 wt% hard segment. Combined with SAXS characterization at melt temperatures, a single phase melt is suggested in these materials which extends to temperatures below the hard segment melting point. © 1994 John Wiley & Sons, Inc.     

Real‐time SAXS and WAXS study of the multiple melting behavior of poly(ε‐caprolactone)

The multiple melting behavior of poly(ε‐caprolactone) (PCL) was investigated by real‐time small angle X‐ray scattering (SAXS) and wide angle X‐ray scattering (WAXS) measurements coupling with differential scanning calorimetry (DSC). Semicrystalline specimens prepared by a continuous cooling process showed lengthening of the Bragg period during the progress of double melting. A model of variable thickness of lamella was proposed to fit to the SAXS patterns and revealed that both the crystalline lamella and the amorphous layer contributed to the increase in Bragg period while the later dominated the contribution. The model of variable thickness although satisfied the SAXS data was unable to compromise the data from other probing tools. A modification of the model proposed that each lamella piling up to construct the stacks in the crystallites was itself nonuniform in thickness. The modification with the parallel occurrence of the mechanism of surface melting and crystallization successfully compromised the observations from SAXS, DSC, and optical microscopy and provided a new perspective for the explanation to lengthening of the Bragg period related to multiple melting behavior. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 1777–1785, 2010     

中介相态丙烯-乙烯无规共聚物在热处理过程中的结构演变

通过熔体淬冷方式制备了中介相态丙烯-乙烯无规共聚物(PPR),综合使用原位红外光谱、原位X-射线散射(WAXD/SAXS)、示差扫描量热分析(DSC)和动态机械热分析(DMA)等方法系统研究了中介相态PPR在升温过程中的微观结构演变.红外光谱研究结果表明,在连续升温过程中,中介相态PPR在30~50?C之间分子链构象发生了变化,其可能源于刚性无定形区(RAF)中部分链段构象的无序化转变,并发现在RAF中存在长度为n≤13(n为31螺旋序列中丙烯单元的个数)的螺旋序列.中介相态PPR在连续升温过程中经历了RAF中链段构象的无序化转变、中介相向α晶的转变、不完善α晶的熔融和α晶的完善化,以及α晶熔融4个转变过程.中介相向α晶的转变是一个异相成核生长过程,其结晶活化能ΔE=67.94 k J/mol.     

Evolution of Morphology and Structure During Crystallization and Melting in Syndiotactic Polypropylene

Polypropylene( PP) has developed into one of the most useful plastic materials.Ithas many attractive properties,among them,a relatively low price.It also possesses awide range of possibilities for chemical modification[1 ,2 ] .The structure and morphologyof PP have a directimpacton the final properties. Therefore,there is growing interestinunderstanding the structure and morphology of stereoregular PP[1～ 6] .　For isotactic PP(i PP) ,extensive structural and morphological studies have be…     

三臂PPO-PDLA-PLLA 嵌段共聚物的制备与结构及其立构复合体的结晶行为

以环氧丙烷聚醚三元醇(PPO)为起始剂, 开环聚合D 型丙交酯(DLA), 合成三臂环氧丙烷聚醚三元醇-聚右旋乳酸(PPO-PDLA)嵌段预聚体. 采用端基活化技术对预聚体进行端羟基活化, 再与L 型丙交酯(LLA)进行逐步开环聚合,合成了不同分子量的三臂环氧丙烷聚醚三元醇-聚右旋乳酸-聚左旋乳酸(PPO-PDLA-PLLA)嵌段共聚物. 采用红外(FTIR)、核磁(NMR)和凝胶渗透色谱(GPC)等对三臂PPO-PDLA-PLLA 嵌段共聚物的测试表明, 合成的嵌段共聚物分子链具有很高的立构规整度; 通过调节LLA 单体与PPO-PDLA 预聚体的投料比, 不仅可控制产物的分子序列结构, 而且样品的数均分子量可大于100 kDa. 差示扫描量热仪(DSC)和广角X 射线衍射(WAXD)结果显示, 三臂PPO-PDLAPLLA嵌段共聚物的异构体链段分子间生成立构复合晶体, 其熔点约为200 ℃, 且没有PLLA 均聚物链段结晶现象. 实验结果表明, 这是一类具有实际应用价值的新型耐热聚乳酸(PLA)材料.     

Morphology development during solid-state annealing of poly(ether-ester) multiblock copolymers

Morphology development during isothermal annealing of poly(ether-ester) multiblock copolymers with hard segments containing poly(tetramethylene isophthalate) is examined by differential scanning calorimetry (DSC) and small-angle x-ray scattering (SAXS). Reorganization in the solid-state occurs by melting and recrystallization. At temperatures close to the melting point, glass transition measurements after quenching from the annealing temperature suggest microphase mixing follows melting. The temperature of maximum recrystallization rate is elevated relative to that of isothermal crystallization. SAXS experiments suggest that a memory of the initial morphology is retained during annealing. Aspects of the DSC scans related to crystallization on cooling and rescanning also suggest that the morphology at the annealing temperature plays a governing role in the determination of the degree of order possible on cooling. The crystalline regions stable at the annealing temperature are envisioned to function in a dual role, acting as nucleation centers for recrystallization and as a form of “constraint” to ordering on cooling. © 1996 John Wiley & Sons, Inc.     

Morphology of homogeneous copolymers of ethylene and 1‐octene. III. Structural changes during heating as revealed by time‐resolved SAXS and WAXD

The structural changes of two linear polyethylenes, LPEs, with different molar mass and of two homogeneous copolymers of ethylene and 1‐octene with comparable comonomer content but different molar mass were monitored during heating at 10 °C per minute using synchrotron radiation SAXS. Two sets of samples, cooled at 0.1 °C per minute and quenched in liquid nitrogen, respectively, were studied. All LPEs display surface melting between room temperature and the end melting temperature, whereas complete melting, according to lamellar thickness, only occurs at the highest temperatures where DSC displays a pronounced melting peak. There is recrystallization followed by isothermal lamellar thickening if annealing steps are inserted. The lamellar crystals of slowly cooled homogeneous copolymers melt in the reverse order of their formation, that is, crystals melt according to their thickness. Quenching creates unstable crystals through the cocrystallization of ethylene sequences with different length. These crystals repeatedly melt and co‐recrystallize during heating. The exothermic heat due to recrystallization partially compensates the endothermic heat due to melting resulting in a narrow overall DSC melting peak with its maximum at a higher temperature than the melting peak of slowly cooled copolymers. With increasing temperature, the crystallinity of quenched copolymers overtakes the one of slowly cooled samples due to co‐recrystallization by which an overcrowding of leaving chains at the crystal surfaces is avoided. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 1975–1991, 2000     

Hydrophilic segmented block copolymers based on poly(ethylene oxide) and monodisperse amide segments

Segmented block copolymers based on poly(ethylene oxide) (PEO) flexible segments and monodisperse crystallizable bisester tetra‐amide segments were made via a polycondensation reaction. The molecular weight of the PEO segments varied from 600 to 4600 g/mol and a bisester tetra‐amide segment (T6T6T) based on dimethyl terephthalate (T) and hexamethylenediamine (6) was used. The resulting copolymers were melt‐processable and transparent. The crystallinity of the copolymers was investigated by differential scanning calorimetry (DSC) and Fourier Transform infrared (FTIR). The thermal properties were studied by DSC, temperature modulated synchrotron small angle X‐ray scattering (SAXS), and dynamic mechanical analysis (DMA). The elastic properties were evaluated by compression set (CS) test. The crystallinity of the T6T6T segments in the copolymers was high (>84%) and the crystallization fast due to the use of monodisperse tetra‐amide segments. DMA experiments showed that the materials had a low T_g, a broad and almost temperature independent rubbery plateau and a sharp flow temperature. With increasing PEO length both the PEO melting temperature and the PEO crystallinity increased. When the PEO segment length was longer than 2000 g/mol the PEO melting temperature was above room temperature and this resulted in a higher modulus and in higher compression set values at room temperature. The properties of PEO‐T6T6T copolymers were compared with similar poly(propylene oxide) and poly(tetramethylene oxide) copolymers. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 4522–4535, 2007     

Crystallization and melting behavior of low molar weight PEO–PPO–PEO triblock copolymers

The crystallization behavior of a series of poly(ethylene oxide)–poly(propylene oxide)–poly(ethylene oxide) (PEO–PPO–PEO) triblock copolymers (Pluronics) was investigated using time-resolved small-angle X-ray scattering (SAXS), thermal analysis, and polarized optical microscopy. For comparison, a PEO homopolymer, PEO3K, was also included. Time-resolved SAXS during the crystallization of PEO3K shows a typical “two-step” process, i.e., in the initial stage, a metastable crystal with nonintegral folding (NIF) structure forms first, then, it transforms into integral folding (IF) structures, the IF(0) and the IF(1). In contrast with PEO3K, the PEO–PPO–PEO triblock copolymers show a “one-step” crystallization process, i.e., the PEO blocks crystallize directly into the final state and do not change with time. In thermal analysis, only one major solid–melt transition is observed during isothermal crystallization and subsequent melting for triblock copolymers. In the full temperature range, a linear crystal growth is observed. The crystal growth rates monotonously decrease with crystallization temperatures. Notches or breaks due to the NIF–IF transition as clearly seen for PEO3K cannot be recognized for Pluronics. Based on these results, we conclude that the crystallization of PEO–PPO–PEO triblock copolymers follows a “one-step” process; no metastable structure serving as an intermediate state is formed during the crystallization process within the time scale of the current experiments (<120 min).     

Temperature‐dependent polymorphic crystalline structure and melting behavior of poly(butylene adipate) investigated by time‐resolved FTIR spectroscopy

The polymorphic crystalline structure and melting behavior of biodegradable poly(butylene adipate) (PBA) samples melt‐crystallized at different crystallization temperatures were studied by differential scanning calorimetry (DSC) and fourier transform infrared (FTIR) spectroscopy. The crystalline structure and melting behavior of PBA were found to be greatly dependent on the crystallization temperature. By comparison of the FTIR spectra and the corresponding second derivatives between the α‐ and β‐crystal of PBA, the spectral differences were identified for the IR bands appeared at 1485, 1271, 1183, and 930 cm^?1 and the possible reasons were presented. Especially, the 930 cm^?1 band was found to be a characteristic band for the β‐crystal. Combining the DSC data with the analysis of normalized intensity changes of several main IR bands during the melting process, the melting behaviors of the α‐ and β‐crystal were clarified in detail. It is demonstrated by the in situ IR measurement that the β‐crystalline phase would transform into the α‐crystalline phase during the melting process, and the solid–solid phase transition from the β‐ to α‐crystal was well elucidated by comparing the intensity changes of the 1170 and 930 cm^?1 bands. The dependence of the β‐ to α‐crystal phase transition on the heating rate was revealed by monitoring the intensity ratio of the 909 and 930 cm^?1 band. It was suggested that at the heating rate of 0.5 or 1 °C/min, the percent amount of the transformed α‐crystal from the β‐crystal was much higher than that at the higher heating rate. The β‐crystal transforms into the α‐crystal incompletely at the higher heating rate because of the less time available for the phase transition. In addition, the β‐ to α‐crystal phase transition was further confirmed by the IR band shifts during the melting process. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 1997–2007, 2009     

Time-resolved SAXS studies of morphological changes in cold crystallized poly(ethylene terephthalate) during annealing and heating

Structural changes occurring during crystallization of quenched amorphous poly(ethylene terephthalate) (PET) and subsequent cooling/heating cycles have been studied by real-time small-angle x-ray scattering (SAXS), using synchrotron radiation. Initial crystallization is found to occur by insertion of new lamellae between the existing ones, while rapid continuous melting/recrystallization happens when the cold-crystallized PET samples are heated above the previous highest annealing temperature. Such melting/recrystalization results in irreversible increases in the lamellar long period, the crystal thickness and the density difference between the crystalline and amorphous regions; in contrast, at temperatures below the prior highest crystallization temperature, the structural changes are dominated by reversible effects such as thermal expansion. However, throughout the entire temperature range up to the melting point around 250 °C, the crystal core thickness remains quite small, less than ca. 50 Å, and the linear crystallinity of lamellar stacks remains nearly constant around 0.3. Such a low crystallinity indicates the presence of thick order-disorder interfacial layers on the lamellar surface, whose thickness increases with temperature.Dedicated to Prof. E. W. Fischer on the occasion of his 65th birthday.     

Thermal properties and influence of orientation on crystalline morphologies in stereoblock polypropylene and related elastomers

Atomic force microscopy (AFM), small angle X‐ray scattering (SAXS), temperature modulated differential scanning calorimetry (TMDSC), variable heating rate DSC, an independent rapid heating rate method for melting points, and cyclic mechanical testing were used to study semicrystalline thermoplastic elastomeric polypropylenes (ELPPs) and related semicrystalline polyolefins including ethylene copolymers. Low crystallinity (ca., 9 and 15%) ELPP samples were studied by AFM in the nonoriented and melt‐oriented states. AFM images taken as a function of time after quenching of a melt‐drawn and highly nucleated film resolved details of secondary crystallization involving lateral growth on the ordered row‐nucleated structures. For nonoriented films, isothermal melt crystallization at high temperatures (110 °C) led to similar features for the two ELPPs. The dominant crystalline morphology studied by AFM consisted of small (several nm in width) granular crystallites organized into immature but large spherulites spanning tens of microns. A striking cross‐hatch morphology was detected in regions of the surface in 110 °C crystallized samples, which is contrasted with melt‐drawn films where row nucleated structures dominated the morphology in the film under no external stress. AFM was also used to monitor the morphological changes that occurred as the films were stretched at 25 °C. Break‐down of lamellae was observed, resulting in oriented narrow fibrils. Cyclic stress‐strain curves showed the expected result where lower crystallinity ELPPs had higher recoverable levels of set after both 100 and 500% elongation. TMDSC was used to resolve the broad melting and recrystallization regions in these low to medium crystallinity ELPP systems, and to contrast the results with ethylene copolymers. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2011     

Correlation of the elution behavior in temperature rising elution fractionation and melting in the solid‐state and in the presence of a diluent of polyethylene copolymers

Compositionally homogeneous poly(ethylene‐α‐olefin) random copolymers with 1‐butene and 1‐hexene comonomers have been studied. The melting of solution‐crystallized specimens of these copolymers in the presence of trichlorobenzene as a diluent with differential scanning calorimetry (DSC) is well correlated with analytical temperature rising elution fractionation (A‐TREF) elution temperature profiles. This indicates that the A‐TREF experiment is essentially a diluent melting experiment. Furthermore, the correction of the corresponding solid‐state melting endotherms of these copolymers with Flory's diluent melting equation yields curves that also correlate very well with the DSC diluent melting curves and the A‐TREF elution temperature profiles. Values of χ, the Flory–Huggins interaction parameter, are determined for these copolymers in trichlorobenzene. χ decreases as short‐chain branching increases. The A‐TREF elution temperature profiles of one of these copolymers are the same, within experimental error, for dilute‐solution crystallizations of the copolymer performed over an extremely broad time schedule (10 s to 3 days). This indicates the profound effect of the branches, as limiting points of the ethylene sequences, in controlling the crystal thickness distribution, which in turn controls the melting point in the presence of the diluent, or the elution temperature from the A‐TREF. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 2819–2832, 2001     

苯乙烯-氧乙烯-苯乙烯三嵌段聚合物的受限结晶行为的反气相分析

 采用反气相法研究了苯乙烯 氧乙烯 苯乙烯三嵌段结晶聚合物 (PS PEO PS)的结晶熔融相变 ,测定了PS PEO PS的结晶度、熔点以及熔程 ,探讨了正构烷烃探针分子的碳链长度对测定结果的影响。研究结果表明 :PS PEO PS的微相分离对PEO链段的结晶行为有较大的影响 ,其晶体结构中存在由多种不完善PEO结晶和PS非结晶构成的中间层 ;正构烷烃探针分子的碳链长度对测定PS PEO PS的熔点和熔程无影响 ,但对结晶度测定和PEO结晶熔融相变的检测影响较大 ,所测得PS PEO PS的结晶度随正构烷烃探针分子碳链的增长而降低。     

MOLECULAR AND SUPRAMOLECULAR ORDERING IN CONFINED ENVIRONMENTS

Crystal and phase morphologies and structures determined by self-organization of crystalline-amorphous diblockcopolymers, crystallization of the crystallizable blocks, and vitrification of the amorphous blocks are reviewed through asystematic study on a series of poly(ethylene oxide)-b-polystyrene (PEO-b-PS) diblock copolymers. On the base ofcompetitions among these three processes, molecular and supramolecular ordering in confined environments can beinvestigated. In a concentration-fluctuation-induced disordered (D_(CF)) diblock copolymer, the competition between crystalli-zation of the PEO blocks and vitrification of the PS blocks is momtored by time-resolved simultaneous small angle X-rayscattering (SAXS) and wide angle X-ray diffraction (WAXD) techniques. In the case of T_c相似文献   

Crystallization kinetics and morphology of biodegradable poly(butylene succinate‐co‐propylene succinate)s

The crystallization behavior of biodegradable poly(butylene succinate) and copolyesters poly(butylene succinate‐co‐propylene succinate)s (PBSPS) was investigated by using ¹H NMR, DSC and POM, respectively. Isothermal crystallization kinetics of the polyesters has been analyzed by the Avrami equation. The 2.2‐2.8 range of Avrami exponential n indicated that the crystallization mechanism was a heterogeneous nucleation with spherical growth geometry in the crystallization process of polyesters. Multiple melting peaks were observed during heating process after isothermal crystallization, and it could be explained by the melting and recrystallization model. PBSPS was identified to have the same crystal structure with that of PBS by using wide‐angle X‐ray diffraction (WAXD), suggesting that only BS unit crystallized while the PS unit was in an amorphous state. The crystal structure of polyesters was not affected by the crystallization temperatures, too. Besides the normal extinction crosses under the POM, the double‐banded extinction patterns with periodic distance along the radial direction were also observed in the spherulites of PBS and PBSPS. The morphology of spherulites strongly depended on the crystallization temperature. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 420–428, 2007     

Synthesis of high‐impact biodegradable multiblock copolymers comprising of poly(butylene succinate) and poly(1,2‐propylene succinate) with hexamethylene diisocyanate as chain extender

Block copolymers demonstrate excellent thermal and mechanical properties superior to their corresponding random copolymers and homopolymers. However, it is difficult to synthesize block copolymers comprising of different polyester segments by copolycondensation due to the serious transesterification reaction. In this study, multiblock copolymers comprising of two different polyester segments, i.e. crystallizable poly(butylene succinate) (PBS) and amorphous poly(1,2‐propylene succinate) (PPSu), were synthesized by chain‐extension with hexamethylene diisocyanate (HDI). Amorphous PPSu segment was incorporated to improve the impact strength of PBS. The copolymers were characterized by GPC, laser light scattering (LLS), NMR, DSC, and mechanical testing. The results of ¹³C NMR spectra suggest that multiblock copolymers with regular sequential structure have been successfully synthesized. The data of DSC and mechanical testing indicate that block copolymers possess excellent thermal and mechanical properties with satisfactory tensile strength and extraordinary impact strength achieving upto 1900% of pure PBS. The influence of PPSu ratio and chain length of both the segments on the thermal and mechanical properties was investigated. The incorporation of an amorphous soft segment PPSu imparts high‐impact resistance to the copolymers without obviously decreasing the melting point (T_m). The favorable mechanical and thermal properties of the copolymers also depend on their regular sequential structure. At the same time, the introduction of amorphous PPSu segment enhances the enzymatic degradation rate of the multiblock copolymers. Copyright © 2009 John Wiley & Sons, Ltd.     

Morphological changes during heating in poly(L‐lactic acid)/poly(butylene succinate) blend systems as studied by synchrotron X‐ray scattering

Blends of poly(L ‐lactic acid) (PLA) and poly(butylene succinate) (PBS) were prepared in various compositions via melt mixing, and the morphological changes were investigated with differential scanning calorimetry and synchrotron wide‐angle and small‐angle X‐ray scattering techniques at a heating rate of 10 °C/min. Differential scanning calorimetry thermograms of PLA/PBS blends showed two distinct melting peaks over the entire composition range. The exothermal peak for PLA shifted significantly to a lower temperature and overlapped with that of PBS around 100 °C. A depression of the melting point of the PLA component via blending was observed. The synchrotron wide‐angle X‐ray scattering during heating revealed that there was no cocrystallization or crystal modification via blending. The synchrotron small‐angle X‐ray scattering data showed that well‐defined double‐scattering peaks (or peaks with a clear scattering shoulder) appeared during crystallization, indicating that this system possessed dual lamellar stacks. These peaks were deconvoluted into two components with a peak separation computer program, and then the morphological parameters of each component were obtained by means of the correlation function. The long period and average lamellar thickness of the two components before melting decreased with an increasing content of the other polymer component. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1931–1939, 2002     

The multiple melting endotherms from poly(butylene terephthalate)

The melting behavior of poly(butylene terephthalate) (PBT) has been investigated, and a simulation has been performed to determine whether the multiple melting endotherms observed during the thermal analysis of PBT can be explained by the simultaneous melting and recrystallization of an initial distribution of crystal melting temperatures that contains only one maximum and two inflection points. Specimens that were cooled at constant rates from the melt showed between one and three melting endotherms upon heating in a differential scanning calorimeter (DSC). The position and breadth of the crystallization exotherms upon cooling from the melt and small-angle x-ray scattering showed that as the cooling rate is increased, the distribution of melting temperatures broadens and shifts to lower temperatures. By combining temperature-dependent recrystallization with an initial distribution of melting temperatures, simulated DSC curves were produced that agreed well with experimental DSC curves. In instances of triple peaked curves, the high temperature peak was due to crystals formed during the scanning process, and the middle and low temperature peaks were due to crystals originally present in the material. Satisfactory agreement between the experimental and simulated curves was found without considering additional crystallization from the amorphous regions during the scanning process.