Characterization of N-isopropyl acrylamide/acrylic acid grafted polypropylene nonwoven fabric developed by radiation-induced graft polymerization

Radiation-induced graft copolymerization of N-isopropylacrylamide (NIPAAm) and acrylic acid (AA) mixture was carried out on polypropylene nonwoven fabric to develop a thermosensitive material and has been found to affect the thermal and physical characteristics of fabric. The grafted fabrics with different monomer ratios were characterized by thermal gravimetric analysis (TGA), fourier transform infrared spectroscopy (FTIR), differential scanning calorimetry (DSC), X-ray diffraction (XRD), contact angle and atomic force microscopy (AFM). Results of FTIR clearly indicated that poly(acrylic acid) and poly(N-isopropyl acrylamide) were successfully grafted onto the membrane surface. TGA results showed that the thermal stability of PP fabric increased after grafting of NIPAAm/AA. The crystallinity values from DSC and XRD were found to decrease with increase in degree of grafting because of the addition of grafted chains within the noncrystalline region. The decrease in contact angles of the grafted fabric with an increase of the degree of grafting shows that PNIPAAm/PAA exists as the hydrophilic component. The increase in surface roughness after grafting was observed by AFM.     

Radiation induced graft polymerization of a fluorinated acrylate onto fabric

A fluoride acrylate monomer, 1H,1H,2H,2H-nonafluorohexyl-1-acrylate (denoted as F4), was grafted onto cotton fabric through a simultaneous irradiation induced graft polymerization technique. The grafted cotton fabric (denoted as cotton–F4) is superhydrophobic (SCF) when the degree of grafting (DG) exceeded 10%. The morphology of the cotton fabric was unchanged. In addition, the mechanical properties of the cotton fabric and SCF samples were also studied. The results showed that the decrease in mechanical properties was less than 20%, indicating that the SCF retained good mechanical strength.     

Preparation, characterization, and antimicrobial property of cotton cellulose fabric grafted with poly (propylene imine) dendrimer

Two generations of poly (propylene imine) dendrimer with amino terminated groups (G2- and G5-PPI-NH₂) were grafted on cotton cellulose fabric using cross linking agents (citric or glutaric acids). Fourier transform infrared (FTIR) spectroscopy identified ester groups which were formed between hydroxyl groups of the cotton fabric and carboxylic groups of the cross linking agents. Also, attenuated total reflectance-FTIR (ATR-FTIR) analysis confirmed formation of amide groups between the carboxylic groups of the cross linking agents and the amino end groups of the dendrimers. Nitrogen content (N-content) analysis revealed the presence of the dendrimers on the cotton fabric even after 5 washing cycles. In order to study the dispersion of the PPI dendrimers on the surface of the cotton fabric, field emission scanning electron microscopy (FE-SEM) was performed. The particle size distribution of the G2- and G5-PPI-NH₂ aqueous solutions was also determined by dynamic light scattering (DLS) analysis. Antimicrobial activity of the PPI dendrimer aqueous solutions and the cotton cellulose fabric grafted with the dendrimers was evaluated both quantitatively and qualitatively against Gram-positive bacterium (Staphylococcus aureus), Gram-negative bacteria (Pseudomonas aeruginosa and Escherichia coli) and fungus (Candida albicans). The dendrimer grafted cotton cellulose fabric exhibited a 99 % reduction in bacterial counts against S. aureus, E. coli and C. albicans. The antimicrobial activities of the grafted cotton cellulose fabric with the PPI dendrimers were maintained even after 5 washing cycles.     

New Grafted Copolymers Carrying Betaine Units Based on Gellan and N-Vinylimidazole as Precursors for Design of Drug Delivery Systems

New grafted copolymers possessing structural units of 1-vinyl-3-(1-carboxymethyl) imidazolium betaine were obtained by graft copolymerization of N-vinylimidazole onto gellan gum followed by the polymer-analogous reactions on grafted polymer with the highest grafting percentage using sodium chloroacetate as the betainization agent. The grafted copolymers were prepared using ammonium persulfate/N,N,N′,N′ tetramethylethylenediamine in a nitrogen atmosphere. The grafting reaction conditions were optimized by changing one of the following reaction parameters: initiator concentration, monomer concentration, polymer concentration, reaction time or temperature, while the other parameters remained constant. The highest grafting yield was obtained under the following reaction conditions: c_i = 0.08 mol/L, c_m = 0.8 mol/L, c_p = 8 g/L, t_r = 4 h and T = 50 °C. The kinetics of the graft copolymerization of N-vinylimidazole onto gellan was discussed and a suitable reaction mechanism was proposed. The evidence of the grafting reaction was confirmed through FTIR spectroscopy, X-ray diffraction, ¹H-NMR spectroscopy and scanning electron microscopy. The grafted copolymer with betaine structure was obtained by a nucleophilic substitution reaction where the betainization agent was sodium chloroacetate. Preliminary results prove the ability of the grafted copolymers to bind amphoteric drugs (cefotaxime) and, therefore, the possibility of developing the new sustained drug release systems.     

Sugar end-capped polyethylene: Ceric ammonium nitrate initiated oxidation and melt phase grafting of glucose onto polyethylene and its microbial degradation

Low density polyethylene (LDPE) was modified to introduce biodegradability by grafting highly hydrophilic monomers (which can act as nutrients for microorganisms) such as glucose by a novel melt phase reaction using Brabender plasti-corder in the presence of ceric ammonium nitrate (CAN) to obtain 4-O-hydroxymethyl d-arabinose (sugar) end-capped LDPE (Su-g-LDPE) at a maximum grafting of 16%. The grafted polymers were characterized by FTIR, thermal analysis, WAXD and mechanical property measurements. The biodegradability of Su-g-LDPE was carried out by soil-burial test and by optical density measurements in presence of an aerobic bacterium Pseudomonas sp. The degraded polymer shows changes in weight, crystallinity and inherent viscosity. Optical density of the medium registered an increase with degradation. FTIR spectra of the degraded samples showed 70% decrease in the ketone carbonyl index (ν₁₇₁₉/ν₁₄₆₅) of Su-g-LDPE indicating microbial degradation of LDPE matrix, which was further confirmed by SEM micrographs. The present data support a microbial oxidation process involving β-oxidation whereby the carbonyl is further oxidized to carboxylic acid and affects cleavage of the LDPE chain at the ends.     

Preparation of thermosensitive membranes by radiation grafting of acrylic acid/N-isopropyl acrylamide binary mixture on PET fabric

Thermosensitive membranes were prepared by radiation-induced graft copolymerization of monomers on PET fabrics. A binary mixture of N-isopropyl acrylamide (NIPAAm) and acrylic acid (AA) was grafted on polyester fabric as a base material to introduce thermosensitive poly(N-isopropyl acrylamide) pendant chains having LCST slightly higher than 37 °C in the membrane. The influence of ferrous sulfate, radiation dose and monomer composition on the degree of grafting was studied. The structure of the grafted fabric was characterized by thermogravimetric analysis, differential scanning calorimetry and scanning electron microscopy. The thermosensitive nature of the fabric was monitored by swelling at different temperatures. The graft copolymerization of AA with NIPAAm enhanced the LCST of the resultant membrane to ∼37 °C. The moisture vapor transmission rate (MVTR) and air permeability of the fabric decreased slightly, may be due to the slight blocking of the fabric pores. The immobilization of tetracycline hydrochloride as the model drug and its release characteristics at different temperatures were monitored.     

Radiation-induced grafting of acrylamide onto guar gum in aqueous medium: Synthesis and characterization of grafted polymer guar-g-acrylamide

Mutual radiation grafting technique has been applied to carry out grafting of acrylamide (AAm) onto guar gum (GG) using high-energy Co⁶⁰ γ radiation to enhance its flocculating properties for industrial effluents. The grafted product was characterized using analytical probes like elemental analysis, thermal analysis, Fourier transformed infrared (FTIR), X-ray diffraction (XRD) and scanning electron microscope (SEM). The grafting extent was observed to decrease with the dose rate and increase with the concentration of AAm. Thermo gravimetric analysis (TGA) of grafted and ungrafted samples indicated better stability of grafted product. γ and microwave radiation effect on grafted and virgin GG has also been reported.     

Radiation-induced grafting of styrene into poly(vinylidene fluoride) film by simultaneous method with two different solvents

Radiation-induced grafting of styrene into poly(vinylidene fluoride) (PVDF) films with 0.125 mm thickness at doses of 1 and 2.5 kGy in the presence of a styrene/N,N-dimethylformamide (DMF) solution (1:1, v/v) and at doses of 20, 40 and 80 kGy in presence of a styrene/toluene solution (1:1, v/v) at dose rate of 5 kGy h^?1 was carried out by the simultaneous method under nitrogen atmosphere and room temperature, using gamma rays from a Co-60. The films were characterized before and after modification by calculated grafting yield (GY %), infrared spectroscopy (FT-IR), scanning electron microscopy (SEM), differential scanning calorimetry (DSC) and thermogravimetry (TG/DTG). GY results shows that grafting increases with dose, and the grafting of styrene was confirm by FT-IR due to the new characteristic peaks and by the TG and DSC attributed to changes in thermal behavior of the grafted material. Results showed that the system allows the controlled grafting of styrene into PVDF using gamma rays at doses as low as 1 kGy in DMF.     

High density cationic polymer brushes from combined “click chemistry” and RAFT‐mediated polymerization

A simple method for preparing cationic poly[(ar‐vinylbenzyl)trimethylammonium chloride)] [poly(VBTAC)] brushes was used by combined technology of “click chemistry” and reversible addition‐fragmentation chain transfer (RAFT) polymerization. Initially, silicon surfaces were modified with RAFT chain transfer agent by using a click reaction involving an azide‐modified silicon wafer and alkyne‐terminated 4‐cyanopentanoic acid dithiobenzoate (CPAD). A series of poly(VBTAC) brushes on silicon surface with different molecular weights, thicknesses, and grafting densities were then synthesized by RAFT‐mediated polymerization from the surface immobilized CPAD. The immobilization of CPAD on the silicon wafer and the subsequent polymer formation were characterized by X‐ray photoelectron spectroscopy, water contact angle measurements, grazing angle‐Fourier transform infrared spectroscopy, atomic force microscopy, and ellipsometry analysis. The addition of free CPAD was required for the formation of well‐defined polymer brushes, which subsequently resulted in the presence of free polymer chains in solution. The free polymer chains were isolated and used to estimate the molecular weights and polydispersity index of chains attached to the surface. In addition, by varying the polymerization time, we were able to obtain poly(VBTAC) brushes with grafting density up to 0.78 chains/nm² with homogeneous distributions of apparent needle‐like structures. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Microwave Assisted Graft Copolymerization of N-Isopropyl Acrylamide and Methyl Acrylate on Cellulose: Solid State NMR Analysis and CaCO3 Crystallization

Summary: Graft copolymerization of N-isopropyl acrylamide and methyl acrylate on α-cellulose was carried out under microwave irradiation at specific cut off temperatures with cerium (IV) ammonium nitrate and potassium persulfate (KPS) as the initiating system. The role of KPS was to oxidize Ce (III) to Ce (IV) which is the active species in radical formation. The reactions at a temperature cut off of 60 °C were confirmed by ¹³C nuclear magnetic resonance cross-polarization with magic- angle spinning (¹³C NMR CP/MAS) and Fourier-transform infrared spectroscopy (FTIR). The extent of grafting was calculated from weight gain and ¹³C resonances. The grafted cellulose was thermally more stable than the parent cellulose. An attempt to do grafting at a higher cut off temperature of 80 °C was made, however, no grafting was observed from ¹³C NMR CP/MAS but TGA results showed that a cellulose having more thermal stability resulted which was attributed to cross linking. Crystallization of CaCO₃ was carried out using the grafted materials as templates showed better nucleation and different crystal structure was observed.     

Grafting of commercially available amines bearing aromatic rings onto poly(vinylidene‐co‐hexafluoropropene) copolymers

The grafting of poly(VDF‐co‐HFP) copolymers with different amines containing aromatic rings, such as aniline, benzylamine, and phenylpropylamine, is presented. ¹⁹F NMR characterization enabled us to show that the sites of grafting of aromatic‐containing amines were first difluoromethylene of vinylidene fluoride (VDF) in the hexafluoropropene (HFP)/VDF/HFP triad and then that of VDF adjacent to HFP. The kinetics of grafting of benzylamine, monitored by ¹H NMR spectroscopy, confirmed those sites of grafting and showed that all VDF units located between two HFPs were grafted in the first 150 min, whereas those adjacent to one HFP unit were grafted in the remaining 3000 min. Parameters such as the temperature or the molar percentage of HFP in the copolymer had an influence on the maximum rate of grafted benzylamine. The higher the temperature, the higher the molar percentage of grafted benzylamine. Furthermore, the higher the molar percentage of HFP in the copolymer, the higher the molar percentage of VDF in the HFP/VDF/HFP triad, and the higher the molar percentage of grafted benzylamine. The spacer length between the aromatic ring and the amino group had an influence on the kinetics of grafting: aniline (pK_a = 4.5) could not add onto the polymeric backbone, whereas phenylpropylamine was grafted in the first 150 min, and benzylamine required 3000 min to reach the maximum amount of grafting. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 1855–1868, 2006     

Synthesis and characterization of chitosan grafted poly(N,N-dimethyl-N-methacryloxyethyl-N-(3-sulfopropyl) ammonium) initiated by ceric (IV) ion

Grafting of N,N-dimethyl-N-methacryloxyethyl-N-(3-sulfopropyl) ammonium (DMMSA) onto chitosan using ceric ammonium nitrate as an initiator was studied under nitrogen atmosphere in 2% wt. acetic acid solution. The grafted polymer was confirmed by FT-IR spectroscopy. The extent of grafting could be adjusted by controlling the appropriate reaction conditions. The maximum percentage of grafting about 50% was obtained under optimum condition. A representative grafted copolymer was characterized by thermogravimetric analysis and chitosan was used as reference.     

Synthesis and characterization of anhydride-functional polycaprolactone

Polycaprolactone-graft-maleic anhydride (PCL-g-MA) copolymer was prepared by grafting maleic anhydride onto PCL in a batch mixer and in an extruder using dicumyl peroxide as the initiator. The graft content was determined with the volumetric method by converting the anhydride functions to acid groups and then titrating with ethanolic potassium hydroxide. The grafted polymer was extracted with xylene to remove any unreacted monomer before the estimation step. The effect of temperature and the various concentrations of the initiator and monomer used for the grafting reaction were investigated. The presence of residual initiator in the reaction product was checked using thin-layer chromatography. Molecular weight determination was carried out for the pure and grafted polymer using gel permeation chromatography to determine if chain scission was present. Results indicate that maleic anhydride is grafted onto PCL using free radical initiators. The grafting reaction was confirmed by FTIR and NMR techniques. FTIR spectra showed absorption bands around 1785 and 1858 cm⁻¹. NMR spectra gave signals for methine proton at 3.47 ppm. For a given peroxide level, a higher temperature or residence (reaction) time gave higher percentage of grafted MA. There was an optimum temperature and initiator concentration after which the percentage of MA grafted on PCL decreased. The number-average molecular weight, tensile strength, and the percent elongation of PCL-g-MA were comparable to those of PCL before grafting. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35: 1139–1148, 1997     

Controlled grafting of MMA onto cellulose and cellulose acetate

Homogeneous graft copolymerization of methyl methacrylate onto cellulose and cellulose acetate was carried out in various solvents and solvent systems taking ceric ammonium nitrate, tin (II) 2-ethyl hexanoate [Sn(Oct)₂] and benzoyl peroxide as initiators. The effect of solvents, initiators, initiator and monomer concentration, on graft yield, grafting efficiency and total conversion of monomer to polymer were studied. Formation of Ce³⁺ ion during grafting in presence of CAN enhances the grafting efficiency. Methylene blue was used as a homopolymer inhibitor and controlled the molecular weight of the grafted polymer and its effect on grafting was also studied. In presence of MB, amount of PMMA homopolymer formation reduced and consequently grafting efficiency increased. The number average molecular weights and polydispersity indices of the grafted PMMA were found out by gel permeation chromatography. The products were characterized by FTIR and ¹H-NMR analyses and possible reaction mechanisms were deduced. Finally, thermal degradation of the grafted products was also studied by thermo-gravimetric and differential thermo-gravimetric analyses.     

Polymer-clay nanocomposites: Free-radical grafting of polyacrylamide onto organophilic montmorillonite

This paper is an account of the experiments on grafting polyacrylamide onto organophilic montmorillonite. Cloisite 20A was reacted with vinyltrichlorosilane to replace the edge hydroxyl groups of the clay with a vinyl moiety. Since the reaction liberates HCl, it was performed in the presence of sodium hydrogencarbonate to prevent the exchange of quaternary alkyl ammonium cations with H⁺ ions. Only the silanol groups on the edge of the clay react with vinyltrichlorosilane. The product maintained the same basal spacing as the precursor. The radical polymerization of the product with acrylamide as a vinyl monomer leads to chemical grafting of polyacrylamide onto montmorillonite surface. The homopolymer formed during polymerization was Soxhelt extracted from the grafted organoclay. Chemical grafting of the polymer onto Cloisite 20A was confirmed by IR spectroscopy. The interlayer and surface changes of the clay in the prepared nanocomposite materials and the grafted nano-particles were studied by XRD and SEM. Intercalated nanocomposites were obtained for clay contents of 3-7% and agglomeration occurred at higher clay loadings. The nanocomposites were studied by thermogravimertic analysis (TGA) and dynamic mechanical analysis (DMTA).     

Relations entre la structure et les proprietes des membranes de polytetrafluoroethylene greffe—I. Membranes monogreffees carboxyliques ou basiques

We have determined the equilibrium properties (neutralization and swelling and the transport properties: conductivity and dialysis) of hydrophilic membranes obtained by radiation grafting of acrylic acid or 4-vinylpyridine onto thin PTFE films. The presence of strong counter-ion-membrane interaction (PTFE-PAA-K⁺ and PTFE-P4VP-ClO^?₄) has been confirmed in the beginning of neutralization. The grafting ratios of the samples ranged between a few percent and several hundreds percent. The properties have been studied in connection with the average degrees of ionization and the average molalities of the reactive groups throughout the whole thickness of the membrane. The parameters of the synthesis which determine the structure of acid or basic grafted chains also have an influence on the properties of the resulting membranes. For a high dose-rate (> 100 rad min^?1), the properties of carboxylic membranes are related to the degree of cross-linking: for smaller dose rates, the properties are related to the length of the grafted branches and/or to the state of the skeleton of PTFE. For the basic membranes, the properties are controlled by the length of the grafted branches and the importance of the micro-phase-separation between PTFE and the grafted chains; for low dose rates, when the grafted branches are long, separation of hydrophobic and ionizable zones is noticed for grafting ratios higher than 5%. The carboxylic membranes with lower degrees of grafting, prepared with a high dose rate, exhibit very good permselectivity. The pyridinic membranes with a low degree of grafting could be of practical interest, viz. the manufacture of selective electrodes for perchlorate ions.     

Thermo- and pH-sensitive comb-type grafted poly(N,N-diethylacrylamide-co-acrylic acid) hydrogels with rapid response behaviors

Poly(N,N-diethylacrylamide) with a terminal hydroxyl end group (PDEA-OH) was synthesized by radical telomerization of N,N-diethylacrylamide (DEA) monomer using 2-hydroxyethanethiol as a chain transfer agent. Macromonomer of thermo-sensitive PDEA was synthesized by condensation reaction of PDEA-OH with acryloyl chloride. The macromonomer was characterized by FTIR and ¹H NMR, and the molecular weight was determined by GPC. Thermo- and pH-sensitive comb-type grafted poly(N,N-diethylacrylamide-co-acrylic acid) (PDEA-co-AA) hydrogels (GHs) were successfully prepared by grafting PDEA chains with freely mobile ends onto the backbone of a cross-linked (PDEA-co-AA) network. The results showed that the deswelling behavior of the hydrogels was dependent on the test temperature. At 45 °C (beneath the VPTT of the hydrogels), both the normal-type hydrogels (NHs) and comb-type grafted P(DEA-co-AA) hydrogels had lower deswelling rates. While at 60 °C (far beyond the VPTT of the hydrogels), the deswelling rates of the GHs were faster than that of the NHs. Furthermore, pulsatile stimuli-responsive studies indicated that the GHs had excellent thermo-reversibility and were superior to the NHs in the magnitude of their swelling ratios to temperature changes. However, the reversibility to pH changes was poor for both the NHs and the GHs.     

Radiation-induced grafting of N-isopropylacrylamide onto the brominated poly(2,6-dimethyl-1,4-phenylene oxide) membranes

A novel thermo-sensitive switching membrane has been prepared by radiation-induced simultaneous grafting N-isopropylacrylamide (NIPAAm) onto brominated poly(2,6-dimethyl-1,4-phenylene oxide) BPPO. In order to attain a high grafting degree, the effects of dose, dose rate, concentration of NIPAAm, concentration of inhibitor Cu²⁺, membrane thickness and solvents were investigated. The grafting process was characterized by FTIR spectroscopy and the highest grafting degree obtained was 7.87%. The thermo-sensitive property of the grafted membrane was measured by water flux (20–48 °C). The results showed that the grafted membrane could respond instantly to environmental temperature changes, and there was a sharp change around the lower critical solution temperature as it is normally seen in PNIPAAm hydrogel.     

Polyethylene glycol grafted cotton as phase change polymer

Thermal storage cotton possessing solid–solid phase change properties was prepared by direct grafting of polyethylene glycol (PEG) on cotton fiber/cloth. Attempt has been made to characterize intermediates so that desired grafting could be obtained. The grafting was done by using urethane linkage and the grafted cotton was found to undergo solid–solid phase transition. The modified cotton was characterized by using Fourier transform infrared spectroscopy (FT-IR), ¹³C CPMAS, polarizing optical microscopy, differential scanning calorimetry (DSC) and thermogravimetry respectively. The DSC study revealed quite good storage effect of grafted cotton and the enthalpy of melting was found to be 55–59 J/g with a peak appearing at around 60 °C. During cooling scan, the crystallization peak appeared at around 38 °C. Further, thermogravimetric analysis confirmed good thermal stability up to 300 °C. Appreciable improvement of mechanical properties of cotton has been observed after grafting. The polarizing optical micrograph clearly showed change of morphology after grafting, i.e., the grafted PEG adhering to fiber surface.     

Radiation‐grafted solid polymer electrolyte membrane: studies of fluorinated ethylene propylene (FEP) copolymer‐g‐acrylic acid grafted membranes and their sulfonated derivatives

Acrylic acid was grafted onto FEP by simultaneous radiation technique and the resulting membranes were sulfonated. Results of dynamic mechanical properties of the membranes showed that storage modulus and temperature at tan δ_(max) increases on grafting. X‐ray diffraction (XRD) analysis of the grafted and sulfonated membranes showed decreasing trend in crystallinity with increase in degree of grafting. From scanning electron microscopy (SEM) studies it was confirmed that grafting takes place by the front mechanism. Copyright © 2004 John Wiley & Sons, Ltd.