Effects of oxygen in gamma irradiated aromatic polyesters in film

The effect of gamma irradiation in air is investigated on four thermoplastic polyesters (PET, PBT, PEN, PCT-co-ET) in films containing aromatic rings, in order to evaluate the influence of aromatic density and the role of oxygen on radiation resistance. Physical-chemical-nuclear analyses were used to this purpose. EPR measurements were carried out to detect radical stability against oxygen permeation. Viscometric investigations reported a very similar trend for all the investigated polyesters: a chain break effect that decreases at the highest doses. FT-IR analyses focused on the formation of oxidized species. Positron annihilation spectra pointed out a decrease of the intensity of ortho-positronium formation, while its lifetime remains unchanged with radiation dose.     

Preparation and structure/property relationships of polyesters containing conjugated diacetylene groups

A series of novel polyesters containing conjugated diacetylenes (DA‐polyesters) were prepared from various diacetylene diols with/without methyl side groups and isomers of aromatic acid chlorides via an interfacial condensation. A fully aliphatic DA‐polyester was also prepared for comparison. All synthesised DA‐polyesters are soluble in m‐cresol, and the intrinsic viscosities were measured. In addition, compact and coherent films and sheets can be obtained from some of the polymers via solution or melt casting. The structure, morphology, and properties were characterized using spectroscopic methods, including FTIR, Raman, and WAXD and thermal analysis including TGA, DSC techniques. DMA was carried out on the solution‐cast thin films and melt‐processed samples. Close correlation was found between the structure and properties in these DA‐polyesters. In particular, through analysis using isothermal DSC and Raman spectroscopy, the solid‐state reactivity of the diacetylene groups in these polyesters was found related to the interchain spacings, which are, in turn, controlled by the molecular structure of the polymers. Results have shown that the aliphatic DA‐polyester behaves very differently compared to the aromatic ones. Distinct differences were also observed among meta‐ and para‐disubstituted isomers of the DA‐polyesters. Furthermore, the introduction of methyl side groups has dramatically affected the thermal and thermal mechanical behavior by altering the interchain spacing of the polymers. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 965–974, 1999     

Effect of structure on the thermal degradation and flame retardancy of hexolic anhydride based polyesters

Based on the anhydrides like hexolic (5,6,7,8,10,10-hexachloro -3a,4,4a,5,8,8a,9,9a-octahydro-5,8-methanonaphtho-[2,3-c]-furan-1,3-dione), maleic and phthalic and diols like 1,4-butanediol, cis-2-butene-1,4-diol and 2,3-dichloro-2-butene-1,4-diol, a family of polyesters has been synthesized using azeotropic condensation technique. The structural characterizations of the polyesters have been carried out using infra-red, 1^H - and ¹³C- nuclear magnetic resonance spectroscopic methods. The thermal properties of the polyesters have been studied using thermogravimetric technique. The off-line pyrolysis of these materials was done. The qualitative and semi-quantitative analyses of the volatiles as well as the heavy mass fractions of the degradation products were carried out using a gas chromatograph coupled to a mass selective detector (GC-MSD). Thermogravimetric data indicate that the thermal stability and the char residue of the polyester resins decrease in the order 1,4-butanediol based>cis-2-butene-1,4-diol based>2,3-dichloro-2-butene-1,4-diol based polyesters. The GC-MSD data indicate that the amount of flame cooling agents (hexa-, isomeric penta-, tetra- and isomeric tri-chlorocyclopentadienes) produced during the pyrolysis of the polyesters increases in the order 2,3-dichloro-2-butene-1,4-diol based<cis-2-butene-1,4-diol based<1,4-butanediol based polyesters. The trends observed in these two parameters which are contributing factors to the flame retardancy of the polyester materials were suitably explained on the basis of the effect of the structural changes in the diol part of the polyesters on the primary degradation mechanism, the β-chain scission process.     

Broad-line NMR and dynamic mechanical behavior of some aromatic polyesters

The dynamic mechanical properties of four aromatic polyesters were measured at temperatures in the 78–540°K region at 10³–10⁴ cps. The polymers studied were: poly(1,3 phenylene isophthalate), poly(1,4 phenylene terephthalate), poly(4,4′ diphenylene isophthalate), and poly(4,4′ diphenylene terephthalate). All four polymers had β loss peaks at about 280°K. Distinct β^* mechanical processes were found for the two terephthalate esters. Broad-line nuclear magnetic resonance measurements were carried out in the 150–440°K temperature range on the four polyesters mentioned above in addition to poly(4,4′ diphenylene 4,4′ biphenyl dicarboxylate). A change in NMR second moment takes place in the 190–330°K region, the magnitude of which is dependent on the polymer structure. The results are compared with those found for a series of aromatic polyamides and are discussed in terms of possible motional processes.     

A series of furan‐aromatic polyesters synthesized via direct esterification method based on renewable resources

A series of furan‐aromatic polyesters were successfully synthesized via direct esterification method starting from 2,5‐furandicarboxylic acid, ethylene glycol, 1,3‐propanediol, 1,4‐butanediol, 1,6‐hexanediol, and 1,8‐octanediol and characterized by Fourier transform infrared spectroscopy (FTIR), nuclear magnetic resonance spectroscopy (¹H NMR), X‐ray diffraction (XRD), differential scanning calorimeter (DSC), thermogravimetric analysis (TGA), dynamic mechanical analysis (DMA), tensile tests, and so on. The preliminary evidence clearly showed that direct esterification method was rewarding and worthy to synthesize these furan‐aromatic polyesters. The densities of furan‐aromatic polyesters were ranging from 1.19 to 1.38 kg/m³. The FTIR and ¹H NMR confirmed their expected structures in detail. The results of XRD showed that these furan‐aromatic polyesters were crystalline polyesters. The results of DSC, TGA, DMA, and tensile tests showed that they behaved as thermoplastic polyester, had satisfactory thermal and mechanical properties, and their thermal stabilities were quite similar to that of corresponding benzene‐aromatic polyesters. The results of contact angle measurement showed that they were hydrophilic. The properties above showed that furan‐aromatic polyesters based on renewable resources could be a viable alternative to their successful petrochemical benzene‐aromatic counterpart. Furthermore, they could be used as biopolymer materials according their satisfactory thermal and mechanical properties and hydrophilicity in the future. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Molecular simulation of aromatic polyesters containing oxetane rings in the main chain

Molecular simulation is a powerful research tool for gaining new insights into polymer chemical structures and processes. This paper presents a computational conformational analysis of some aromatic polyesters containing either an oxetane ring or propylene moieties in the main chain. The studied polyesters were synthesised by phase transfer catalysis using 3,3-bis-(chloromethyl)-oxetane, 1,3-dibromopropane and various aromatic diacids. The computational analysis and calculations were performed using the Cerius² program (version 3.5), molecular simulation software for material science, designed by Molecular Simulations Incorporated. This study elucidates some aspects and properties dependent upon supramolecular arrangement of the macromolecular chains. In order to verify the agreement between simulated and experimental results the coefficient of asymmetry, order parameter and glass transition temperature were calculated for each studied aromatic polymer.     

Direct polyesterification by use of phosphorus oxychloride and LiCl in pyridine

The reaction of the N-phosphonium salt of pyridine derived from phosphorus oxychloride in pyridine was successfully used for the preparation of aromatic polyesters with high molecular weight when carried out in the presence of lithium chloride. In the copolycondensations of isophthalic and terephthalic acid with diphenols, the mode of reaction with the diacids was expected to produce several types of the diacid activated intermediates, which might control the sequences of the diacids in the copolymers. The possible variation of the sequences was studied in terms of the mode and copolymer properties such as glass transition temperatures and liquid crystalline transition temperatures. Competitive model reactions were carried out to discuss these relationships. © 1993 John Wiley & Sons, Inc.     

Polymers with Cycloaliphatic Units in the Chain

This paper describes the synthesis and characterization of some polycondensation polymers (poly- and copolyamides, polyesters) which contain cycloaliphatic units in their chains. Syntheses were carried out by a low-temperature polycondensation technique (interfacial and solution), and also by the Yamazaki method in NMP-pyridine solution using triphenylphosphite as the catalyst. The products obtained were characterized by elemental analysis, IR, and x-ray diffraction. Thermoanalytical data have shown very good thermal properties for all products, but especially for the aromatic cycloaliphatic polyamides which were stable up to 400°C.     

Comparative dielectric and thermotropic properties of liquid crystalline polyesters as a function of mesogen group and flexible thioether group length

Two polyesters containing rigid biphenyl and hydroquinone bisbenzoate groups and presenting flexible thioether moieties with different lengths (14 elements in the flexible group) have been carried out using a reaction of the Michaël type. The properties of these polyesters have been compared to those of polyesters of the same type presenting shorter flexible groups (11 elements). All these polymers present thermotropic properties: the biphenyl ones are smectic and the bisbenzoate ones are nematic. The biphenyl polyesters present two types of dielectric relaxations: α and β. The bisbenzoate ones show three relaxations, α and two β (β and β^′). The lengthening of the flexible group increases significantly the flexibility of the molecular chains.     

Effects of noncovalently functionalized multiwalled carbon nanotube with hyperbranched polyesters on mechanical properties of epoxy composites

In order to improve the dispersibility and interface properties of multi-walled carbon nanotubes (MWCNTs) in epoxy resin (EP), aromatic hyperbranched polyesters with terminal carboxyl (HBP) and aromatic hyperbranched polyesters with terminal amino groups (HBPN) were used for noncovalent functionalization of MWCNTs. Epoxy composites reinforced by different types of MWCNT were prepared. The effects of noncovalent functionalization of MWCNTs on the dispersibility, wettability, interface properties and mechanical properties of epoxy composites were investigated. The results show that the dispersibility and wettability of MWCNTs are significantly improved after noncovalent functionalization. A large number of terminal primary amines (NH₂) on noncovalently functionalized MWCNT with HBPN (HBPN-MWCNT) form covalent bonds with EP matrix, and thus the interfacial adhesion is enhanced significantly, resulting in high load transfer efficiency and substantial increase in mechanical properties. The interface with covalent bonding formed between the flexible hyperbranched polyester layer on the surface of HBPN-MWCNT and the EP matrix promotes plastic deformation of the surrounding EP matrix. The toughening mechanisms of HBPN-MWCNT are MWCNT pull-out and a large amount of plastic deformation of the surrounding EP matrix.     

Synthesis,thermal, rheological characteristics,and enzymatic degradation of aliphatic polyesters with lignin‐based aromatic pendant groups

This research aims to produce lignin‐based biodegradable polyesters with improved thermal quality. A series of aliphatic polyesters with lignin‐based aromatic side groups were synthesized by conventional melt‐polycondensation. Decent molecular weight (21–64 kg mol^?1) was achieved for the polymerizations. The molecular structures and thermal and mechanical properties of the obtained polyesters were characterized. As a result, the obtained polyesters are all amorphous, and their glass‐transition temperature (T_g) depends on the size of the pendant aromatic group (31–51 °C). Furthermore, according to the TGA results, the thermal decomposition temperatures of the polyesters are all above 390 °C, which make them superior compared with commercial biodegradable polyesters like polylactic acid or polyhydroxyalkanoates. Finally, rheological characteristics and enzymatic degradation of the obtained polyesters were also measured. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019, 57, 2314–2323     

Isothermal melt-crystallization and melting behavior for three linear aromatic polyesters

Isothermal crystallization and subsequent melting behavior for three different types of linear aromatic polyester, namely poly(ethylene terephthalate) (PET), poly(trimethylene terephthalate) (PTT), and poly(butylene terephthalate) (PBT), were investigated (with an emphasis on PTT in comparison with PET and PBT). These polyesters were different in the number of methylene groups (i.e. 2, 3, and 4 for PET, PTT, and PBT, respectively). Isothermal crystallization studies were carried out in a differential scanning calorimeter (DSC) over the crystallization temperature range of 182-208 °C. The wide-angle X-ray diffraction (WAXD) technique was used to obtain information about crystal modification and apparent degree of crystallinity. The kinetics of the crystallization process was assessed by a direct fitting of the experimental data to the Avrami, Tobin, and Malkin macrokinetic models. It was found that the crystallization rates of these polyesters were in the following order: PBT>PTT>PET, and the melting of these polyesters exhibited multiple-melting phenomenon. Lastly, the equilibrium melting temperature for these polyesters was estimated based on the linear and non-linear Hoffman-Weeks (LHW and NLHW) extrapolative methods.     

Glow wire ignition temperature (GWIT) and comparative tracking index (CTI) of glass fibre filled engineering polymers, blends and flame retarded formulations

Engineering thermoplastic polymers such as polyamides, polycarbonates, semi-crystalline aromatic polyesters and their blends are widely used as insulating materials in electrical and electronic appliances. Flame retardants are often employed in the formulation of these materials, since good performance in terms of ignition and tracking resistance, evaluated by Glow Wire Tests (GWIT) and Comparative Tracking Index (CTI) are required in these applications. In this paper, a comparative evaluation of GWIT and CTI performances has been simultaneously performed for a wide set of glass fibre filled materials chosen among engineering thermoplastics and their blends. Some flame retarded formulations have been also tested, in order to screen the effects of various additives. Useful indications have been obtained on the effect of each polymer and additives on GWIT and CTI properties. In addition, interesting synergies have been observed, especially by blending polyesters and polyamides. Thermogravimetric measurements of char yields have been successfully related with CTI behaviour. The presence of additives changes the structure of the carbonaceous residue, hence the conductivity of the tracks. Neat polycarbonate passed the GWIT test but not CTI, while poly(butylene terephthalate) showed the best balance of GWIT and CTI performance among the pure resins tested. Blending polycarbonate with polyester did not improve significantly GWIT performance, but had a negative effect on tracking resistance. Polyesters/polyamide blends were dominated by polyester in GWIT, but they showed synergistic effects in CTI.     

Synthesis and characterization of soluble aromatic polyesters derived from substituted terphenyl and quinquephenyl diols

Rigid aromatic polyesters containing alkoxy or phenyl-substituted oligophenyls were prepared. Soluble polymers were obtained also in cases where phenyl-substituted quinquephenyl diols were combined with asymmetric phenyl-substituted terephthalic acid. The synthesized polyesters were characterized by viscosimetry, gel permeation chromatography, thermal analysis, and dynamic mechanical analysis. The temperature dependence of the intrinsic viscosity was sensitive to the type of side groups. Thermogravimetry has shown that polyesters with aromatic substituents were stable up to 380–400°C. The glass transition temperatures of the polyesters with aromatic side groups were in the 220–260°C range as determined by DSC. Polyesters with hexyloxy side chains show crystallinity. Dynamic mechanical analysis showed that in the cases where aromatic substituents were used to increase solubility, the obtained polymers have very useful mechanical properties at high temperatures. The polymer having the quinquephenyl unit in the main chain has an almost constant modulus up to 340°C. © 1996 John Wiley & Sons, Inc.     

Synthesis and characterization of 1,3-bis(2-hydroxyethoxy) benzene based saturated and unsaturated polyesters

Polyesterification of adipic acid and maleic anhydride with 1,3-bis(2-hydroxyethoxy)benzene (HER) in the presence of toluene-4-sulphonic acid was carried out using melt condensation technique. The structural characterization of the synthesized polyesters had been carried out using Fourier transform infrared (FTIR) and proton nuclear magnetic resonance (¹H NMR) spectroscopic methods. The thermal properties of the polyesters were studied using differential thermal analysis (DTA) and thermogravimetric analysis (TGA). The activation energies for the thermal degradation of the polyesters were calculated by the method of Dharwadkar and Kharkhanavala and discussed. The char residue value at 600 °C indicated maleic anhydride based polyester is thermally more stable compared to the adipic acid based polyester. The mechanism of degradation of these polyesters is discussed.     

不饱和聚酯树脂的减收缩研究(Ⅱ)——几种饱和聚酯的减收缩作用

饱和聚酯作为减缩剂的优点是制品表面光洁,所得低收缩UP-树脂透明度较好,往往为半透明,使制品外观与原UP-树脂差不多,从而扩大了制品的用途。我们在酸和醇的种类及比例上进行了探索,合成了7种低分子量饱和聚酯并测试了它们的减收缩效果。发现芳香族聚酯具有更好的减收缩性能,其中具有封端结构的效果更佳。此外,制备了几种无填料浇     

Cyanopolyesters

The reaction of alkyl acyl cyanides with electron-rich aromatic substrates in highly acidic media was found to give high yields of bisadducts. Reactions with phenol produced two new eyanobisphenols which readily underwent polycondensation with acid chlorides. The resultant polyesters can be directly compared to the polyesters of bisphenol-A (BPA) strictly on the basis of polar effects since steric differences are nominal. Thermal, mechanical, electrical and solubility characteristics are reported for the cyanopolycarbonates, which show higher thermal transitions and thermal stability than BPA polycarbonate.     

结晶性芳香聚酯高压结晶行为研究进展

运用高压极限手段研究聚合物的结构、形态和性能是20世纪60年代以来兴起的一项聚合物前沿课题。本文主要结合作者自己的研究工作，重点叙述聚对苯二甲酸乙二醇酯(PET)的高压结晶行为研究，包括温度、压力、时间及分子量对PET高压结晶行为的影响，高压结晶PET的形态。以及对PET伸直链晶体结晶机理的探讨，同时简要介绍了对其它结晶性芳香聚酯诸如聚对苯二甲酸丁二醇酯(PBT)及聚对萘二甲酸乙二醇酯(PEN)的高压结晶行为研究，反映了该领域的研究概况和最新进展。并对今后的研究提出了展望。     

Model structures of thermoplastic polyesters having regularly alternated aromatic and fluorinated segments

Linear segmented polyesters containing soft perfluoropolyether (PFPE) and hard aromatic segments are obtained by an interfacial polycondensation reaction of an acyl chloride-ended fluorinated prepolymer with various aromatic diphenols in the presence of phase transfer catalysts (PTC) as accelerators. Experimental conditions for reaching high molecular weights are discussed. The calorimetric analysis (DSC) of all the polyesters synthesized shows a typical biphasic morphology, where a very low T_g (< −110°C) corresponding to the segregated PFPE moiety, is always accompanied by another T_g or a higher melting temperature, depending on the nature of the hard phase. Dynamic-mechanical analysis (DMA) has been carried out confirming the DSC results and suggesting diversified mechanical behaviors at the various temperatures in line with the amorphous or semicrystalline nature of the polymer. Chemical resistance was finally tested by dipping in several solvents and chemicals. The new polyesters show high contact angles, a moderate swelling in many organic solvents and excellent stability in aggressive hydrolytic environments. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 939–947, 1998     

Interfacial Polycondensation in Aqueous and Non-Aqueous Systems

Abstract

Interfacial polycondensation in aqueous and non-aqueous systems has been investigated in order to synthesize various polyamides having functional groups. Rigid aromatic polyamides having pyridine moieties (PPy) were synthesized by interfacial polycondensation using an aqueous system and the solution properties of PPy in concentrated sulfuric acid were investigated in terms of solution viscosity and lyotropic behavior. Interfacial polycondensation in a non-aqueous system using two immiscible solvents was found to be useful for the synthesis of aromatic polyesters and copolyesters.