X‐ray diffraction study of the thermal expansion behavior of cellulose triacetate I

Highly crystalline samples of cellulose triacetate I (CTA I) were prepared from highly crystalline algal cellulose by heterogeneous acetylation. X‐ray diffraction of the prepared samples was carried out in a helium atmosphere at temperatures ranging from 20 to 250 °C. Changes in seven d‐spacings were observed with increasing temperature due to thermal expansion of the CTA I crystals. Unit cell parameters at specific temperatures were determined from these d‐spacings by the least squares method, and then thermal expansion coefficients (TECs) were calculated. The linear TECs of the a, b, and c axes were α_a = 19.3 × 10^?5 °C^?1, α_b = 0.3 × 10^?5 °C^?1 (T < 130 °C), α_b = ?2.5 × 10^?5 °C^?1 (T > 130 °C), and α_c = ?1.9 × 10^?5 °C^?1, respectively. The volume TEC was β = 15.6 × 10^?5 °C^?1, which is about 1.4 and 2.2 times greater than that of cellulose I_β and cellulose III_I, respectively. This large thermal expansion could occur because no hydrogen bonding exists in CTA I. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 517–523, 2009     

Thermogravimetric analysis of cellulose insulation and determination of activation energy of its thermo‐oxidation using non‐isothermal,model‐free methods

The aim of the work was to determine the effect of heating rate on initial decomposition temperature and phases of thermal decomposition of cellulose insulation. The activation energy of thermo‐oxidation of insulation was also determined. Individual samples were heated in the air flow in the thermal range of 100°C to 500°C at rates from 1.9°C min^?1 to 20.1°C min^?1. The initial temperatures of thermal decomposition ranged from 220°C to 320°C, depending on the heating rate. Three regions of thermal decomposition were observed. The maximum rates of mass loss were measured at the temperatures between 288°C and 362°C. The activation energies, which achieved average values between 75 and 80.7 kJ mol^?1, were calculated from the obtained results by non‐isothermal, model‐free methods. Copyright © 2014 John Wiley & Sons, Ltd.     

Lateral thermal expansion of cellulose Iβ and IIII polymorphs

Measurements of the thermal expansion coefficients (TECs) of cellulose crystals in the lateral direction are reported. Oriented films of highly crystalline cellulose I_β and III_I were prepared and then investigated with X‐ray diffraction at specific temperatures from room temperature to 250 °C during the heating process. Cellulose I_β underwent a transition into the high‐temperature phase with the temperature increasing above 220–230 °C; cellulose III_I was transformed into cellulose I_β when the sample was heated above 200 °C. Therefore, the TECs of I_β and III_I below 200 °C were measured. For cellulose I_β, the TEC of the a axis increased linearly from room temperature at α_a = 4.3 × 10^?5 °C^?1 to 200 °C at α_a = 17.0 × 10^?5 °C^?1, but the TEC of the b axis was constant at α_b = 0.5 × 10^?5 °C^?1. Like cellulose I_β, cellulose III_I also showed an anisotropic thermal expansion in the lateral direction. The TECs of the a and b axes were α_a = 7.6 × 10^?5 °C^?1 and α_b = 0.8 × 10^?5 °C^?1. The anisotropic thermal expansion behaviors in the lateral direction for I_β and III_I were closely related to the intermolecular hydrogen‐bonding systems. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1095–1102, 2002     

Novel cellulose derivatives. IV. Preparation and thermal analysis of waxy esters of cellulose

Cellulose esters with linear aliphatic acyl substituents ranging in size from C₁₂ (lauric acid) to C₂₀ (eicosanoic acid) were prepared in homogeneous solution (DMAc/LiCl) using a novel synthetic method based on the use of a mixed p-toluenesulfonic/carboxylic acid anhydride. The resulting waxy cellulose esters had a high degree of substitution (DS), between 2.8 and 2.9, and showed little degradation. Thermal analysis of these cellulose derivatives by differential scanning calorimetry (DSC) and dynamic mechanical thermal analysis (DMTA) revealed a series of transitions that represented motion by both ester substituents and cellulosic main chain. Broad crystallization and melting transitions attributed to side-chain crystallinity were observed in the range between −19 and +55°C; these side-chain T_m and T_c transition temperatures increased by 10°C per carbon atom of the ester substituent. The T_g of these derivatives increased linearly with increasing substituent size from 94°C for C₁₂ (cellulose laurate) to 134°C for C₂₀ (cellulose eicosanoate). Evidence of “main-chain” crystallization was not observed for these samples, except in the case of peracetylated C₁₂ and C₁₄ esters, which had T_m values of 96°C and 107°C, respectively. © 1996 John Wiley & Sons, Inc.     

Structural properties and state of the surface layer of zirconium dioxide promoted by manganese cations

The effect of Mn cations on the structural properties of zirconium dioxide (phase composition and crystallite size) was studied. The cations were introduced by coprecipitation of hydroxide precursors followed by thermal processing at temperatures of 350 to 650°C. It was found by X-ray photoelectron spectroscopy that Mn ⁿ⁺ cations (4 ≥ n ≥ 2, n = 3 being the dominant state) were localized on the surface of MnO _x -ZrO₂ samples calcinated at 350 and 600°C.     

Phase transformation in spodumene–diopside glass

In situ developments of platelike spodumene–diopside grains were obtained by controlled devitrification of the complex system Li₂O–CaO–MgO–Al₂O₃–SiO₂ glass. The crystallization mechanisms of spodumene–diopside glass were measured by isothermal and non-isothermal processes using classical and differential thermal analysis techniques. The Avrami constant n was 2.0–2.1, indicating two-dimensional crystal growth and platelike grains. The crystalline phases precipitated first were high-quartz_s.s., then transformed to β-spodumene and diopside. The Flexural strength, fracture toughness and thermal shock resistance (in 20°C water) increased from 145 MPa, 1.3 MPa m^1/2, 800°C (pure spodumene) to 197 MPa, 2.9 MPa m^1/2 and 920°C (spodumene–diopside) with low thermal expansion coefficient (from 3∼9·10^–7 to 11.8·10^–7 K^–1). This mean in situ developments of platelike spodumene–diopside grains reinforced the low thermal expansion coefficient glass-ceramics.     

Preparation and properties of organo‐modifier free PET/MMT nanocomposites via monomer intercalation and in situ polymerization

In order to prevent the properties, especially transparency, color and health security, of PET/clay nanocomposites from being deteriorated due to the thermal degradation of clay organo‐modifer, we had directly modified sodium montmorillonite (Na⁺‐MMT) with PET's monomer, bis (hydroxyethyl) terephthalate (BHET) which had a degradation temperature higher than 400°C, and successfully prepared the hybrids via in situ polymerization. Nanodispersion of clay and the intercalated morphology were determined, and compared with PET/Na⁺‐MMT hybirds in which Na⁺‐MMT was directly added without any treatment. Improved mechanical properties and T_g were observed for the prepared PET/ BHET‐modified clay composites. More importantly, the film produced from the composites had the same transparency as that of pure PET even when 2 wt% of clay was added. Non‐isothermal and isothermal crystallization experiments showed a very good neculation capability of the nano‐dispersed clay, particularly at higher crystallization temperatures. Copyright © 2009 John Wiley & Sons, Ltd.     

Kinetics and mechanism of the thermal degradation of polysulphide polymer cured with ammonium dichromate: Pyrolysis-gas chromatography and thermogravimetric studies

The kinetics and mechanism of the thermal degradation of thiol-terminated liquid polysulphide polymer cured with ammonium dichromate was studied by pyrolysis-gas chromatography and isothermal and dynamic thermogravimetry. Pyrolysis-gas chromatography showed that the nature and composition of the pyrolysates for the liquid and the cured elastomers were essentially the same. Isothermal measurements were made at 268, 280, 290 and 299°C and maxima in the rates of degradation occurred at 28% conversion (α). Isothermal rates calculated from a kinetic model based on random initiation followed by rapid termination by disproportionation were in good agreement with the experimental values. The dynamic experiments were run at several heating rates from 2 to 100°C/min. Analysis of the data based on the random initiation model gave kinetic parameters that agreed well with the isothermal values and with the values obtained by Ozawa's method, confirming the proposed kinetic model for the degradation. The overall activation energy for the degradation (E_d) was found to be 146.4, 144.1±7.6 and 145.6±7.6 kJ mole⁻¹ by isothermal, dynamic and Ozawa's methods, respectively. The Coats-Redfern method of analysis gave increasing values of E_d with increasing heating rates and showed a kinetic compensation effect.     

The highly crosslinked dimethacrylic/divinylbenzene copolymers

The thermal stability of the ionic liquids (ILs) 1-n-butyl-3-methylimidazolium bromide, [BMIM]Br, and 1-n-octyl-3-methylimidazolium bromide, [OMIM]Br, was evaluated through thermogravimetry (TG). Long-term isothermal TG studies revealed that both of these ILs exhibit appreciable decomposition even at temperatures significantly lower than the onset decomposition temperature, previously determined from fast scan TG experiments. The long-term TG studies of both the ILs showed linear mass loss as a function of time at each temperature of 10 °C interval in the range 533–573 K over a period of 10 h. The kinetics of isothermal decomposition of ILs was analyzed using pseudo-zero-order rate expression. The activation energies for the isothermal decomposition of [BMIM]Br and [OMIM]Br under nitrogen atmosphere are 219.86 and 212.50 kJ mol⁻¹, respectively. The moisture absorption kinetics of these ILs at 25 °C and 30% relative humidity (RH) and at 85 °C and 85% RH were also studied. Water uptake of ILs exposed at 25 °C/30%RH follows a simple saturation behavior in agreement with Weibull model while that at 85 °C/85%RH fortuitously fit into the Henderson–Pabis model.     

Synthesis and thermal properties of cellulose-based polycaprolactones

Cellulose-based polycaprolactone (CAPCL) sheets were prepared from cellulose acetate (CA) and ϵ-caprolactone (CL). Thermal properties of the obtained CAPCL's were studied by differential scanning calorimetry (DSC), thermogravimetry (TG) and TG-Fourier transform infrared spectrometry (TG-FTIR). The glass transition temperatures (T_g 's) of CAPCL decreased with increasing CL/OH ratio, until CL/OH ratio reached 15 and then increased above that ratio. Melting of CAPCL was observed when CL/OH ratio was over 10. The thermal degradation temperatures (T_d 's) of CAPCL increased from ca. 350 °C to 390 °C with increasing CL/OH ratio. The results obtained by TG-FTIR analysis of CAPCL showed that gases with OH, CH, C=O, C-O-C groups evolved by thermal degradation.     

Sustainable poly(ether amide)s from lignin-derived precursors

In recent years, there have been concerted efforts to replace petrochemical products with those from renewable sources due to the unsustainability of petroleum feedstock, and the continued volatility in the price. This work describes the synthesis and thermal properties of two new lignin-derived poly(ether-amide)s as alternative thermoplastics to petroleum-based commodities. Poly-4-(2-aminoethoxy)benzoate (PEAB) and poly-4-(2-aminoethoxy)-3-methoxybenzoate (PEAV) are synthesized by a melt polycondensation and characterized by ¹H NMR spectroscopy and thermal analysis. The number average molecular weight (M_n) of the polymers are estimated from the ¹H NMR spectroscopy analysis, and were shown to be 4100 and 12,000 g/mol for PEAB and PEAV respectively. The PEAB had a higher decomposition temperature (T_d) as well as glass transition temperature (T_g) compared to PEAV; albeit, with a lower molecular weight. The polymers’ T_d were in the range of 330 °C–380 °C and the T_g were between 100 °C and 120 °C. The thermal properties of the polymers are in the desirable range for thermoplastic materials used in the packaging, storage, and coating industries. Furthermore, the polymers are susceptible to degradation under acidic conditions in a short period; a property that is highly desirable for degradable polymers. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 2154–2160     

Synthesis and NMR characterization of 6‐Phenyl‐6‐deoxy‐2,3‐di‐O‐methylcellulose

Cellulose ( 1 ) was converted for the first time to 6‐phenyl‐6‐deoxy‐2,3‐di‐O‐methylcellulose ( 6 ) in 33% overall yield. Intermediates in the five‐step conversion of 1 to­ 6 were: 6‐O‐tritylcellulose ( 2 ), 6‐O‐trityl‐2,3‐di‐O‐methylcellulose ( 3 ), 2,3‐di‐O‐methylcellulose ( 4 ); and 6‐bromo‐6‐deoxy‐2,3‐di‐O‐methylcellulose ( 5 ). Elemental and quantitative carbon‐13 analyses were concurrently used to verify and confirm the degrees of substitution in each new polymer. Gel permeation chromotography (GPC) data were generated to monitor the changes in molecular weight (DP_w) as the synthesis progressed, and the compound average decrease in cellulose DP_w was ～ 27%. Differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA) were used to characterize the decomposition of all polymers. The degradation temperatures ( °C) and percent char at 500 °C of cellulose derivatives 2 to 6 were 308.6 and 6.3%, 227.6 °C and 9.7%, 273.9 °C and 30.2%, 200.4 °C and 25.6%, and 207.2 °C and 27.0%, respectively. The glass transition temperature (T_g) of­6‐O‐tritylcellulose by dynamic mechanical analysis (DMA) occurred at 126.7 °C and the modulus (E′, Pa) dropped 8.9 fold in the transition from ?150 °C to + 180 °C (6.6 × 10⁹ to 7.4 × 10⁸ Pa). Modulus at 20 °C was 3.26 × 10⁹ Pa. Complete proton and carbon‐13 chemical shift assignments of the repeating unit of the title polymer were made by a combination of the HMQC and COSY NMR methods. Ultimate non‐destructive proof of carbon–carbon bond formation at C6 of the anhydroglucose moiety was established by generating correlations between resonances of CH₂6 (anhydroglucose) and C1′, H2′, and H6′ of the attached aryl ring using the heteronuclear multiple‐bond correlation (HMBC) method. In this study, we achieved three major objectives: (a) new methodologies for the chemical modification of cellulose were developed; (b) new cellulose derivatives were designed, prepared and characterized; (c) unequivocal structural proof for carbon–carbon bond formation with cellulose was derived non‐destructively by use of one‐ and two‐dimensional NMR methods. Copyright © 2002 John Wiley & Sons, Ltd.     

Thermal behavior of bismaleimide resin

The cure of a bismaleimide (BMI) neat resin modified with an aromatic diamine and a siloxane elastomer, has been studied by ¹³C solid state nuclear magnetic resonance. Two chemical reactions occur during the cure cycle; at a low temperature, Michael's reaction predominates, while at a high temperature the polymerization of the double bond maleimide creates the network. The degradation of this BMI material was characterized with isothermal and dynamic thermogravimetric analyses in air and in nitrogen. The BMI thermal stability is lower in nitrogen than in air. This behavior is an indication of oxygen participating in reactions at high temperatures. The activation energy (E_a) of thermal degradation was determined from isothermal data using an Arrhenius equation (In V vs. 1/T). The global E_a for the weight loss in air was found to be 91 kJ/mol. The nature and the evolution of the thermal degradation products were the combined analyzed by techniques of pyrolysis, gas chromatography and mass spectrometry. The major thermal decomposition products obtained in the temperature range of 300–700°C are identified as benzene, methyl formamide, aniline, toluene and isocyanate-derived products.     

Synthesis,crystal structure,thermal decomposition,and explosive properties of [Bi(tza)3] n (tza = tetrazole acetic acid)

A coordination compound based on tetrazole acetic acid (Htza) and bismuth(III), [Bi(tza)₃] _n , was synthesized and characterized by single crystal X-ray diffraction analysis, elemental analysis, FT-IR, and ¹H NMR spectroscopy. The crystallographic data show that the crystal belongs to monoclinic, P2₁/n space group, a?=?0.91968(19)?nm, b?=?0.94869(19)?nm, c?=?1.7824(4)?nm, β?=?101.488(3)°, and Z?=?4. The central bismuth(III) is nine-coordinate by three nitrogens from three tetrazole rings and six oxygens of the carboxylate of another three tza^? ions, with each tza^? tridentate, chelating, bridging coordination. The coordination bonds and the intramolecular hydrogen bonds make the complex pack into a layered structure in polymer form. The thermal decomposition mechanism of the title complex was investigated by DSC and TG-DTG techniques. Under nitrogen at a heating rate of 10°C?min^?1, thermal decomposition of the complex contains two intense exothermic processes between 217.4°C and 530.3°C in the DSC curve; the final decomposed residue at 570°C was Bi₂O₃. Sensitivity tests showed that [Bi(tza)₃] _n was sensitive to impact and flame stimulus.     

Thermal stability and dynamic mechanical thermal analysis of epoxy thermosets possessing N,N′-disubstituted pyromellitimide units

Abstract

In this work, three epoxy resins including diglycidyl ethers of N,N′-bis(2-hydroxyethyl)pyromellitimide (DIDGE), bisphenol-A (BADGE), and polyethylene glycol (PEDGE) were isothermally cured by an amine curing agent possessing N,N′-disubstituted pyromellitimide units (denoted by DIDAM). DIDGE resin was synthesized from the reaction of N,N′-bis(2-hydroxyethyl)pyromellitimide with an excess of epichlorohydrin. Also, DIDAM curing agent was prepared from the reaction of pyromellitic dianhydride with an excess of ethylene diamine. Completion of the isothermal curing processes was approved by both Fourier transform-infrared spectroscopy and non-isothermal differential scanning calorimetry (DSC). The DSC traces showed only the phase transitions related to the thermal degradation of the resulting thermosets. According to the thermogravimetric analyses, the DIDGE/DIDAM thermoset showed higher thermal stability at temperatures above 425?°C than the other two thermosets. While BADGE/DIDAM and PEDGE/DIDAM thermosets showed about 70% weight loss in the thermal range of 400–850?°C, DIDGE/DIDAM thermoset was encountered with only about 40% weight loss. The glass transition temperatures (T_g ) of the resulting thermosets were determined using tan δ vs temperature plots obtained from dynamic mechanical thermal analysis. The T_g values of BADGE/DIDAM, DIDGE/DIDAM, and PEDGE/DIDAM thermosets were found to be 211?°C, 189?°C, and 81?°C, respectively.     

Synthesis of Diblock Copolymers With Cellulose Derivatives. 2. Characterization and Thermal Properties of Cellulose Triacetate-Block-Oligoamide-15

Well-defined A-block-B type cellulose derivatives consisting of cellulose triacetate (CTA) and oligoamide-15 were synthesized. Chemical structures of the diblock copolymers were characterized by MALDI-TOF MS, ¹H-NMR, and GPC. Influence of length of CTA and oligoamide-15 segments on their thermal properties was investigated by means of differential scanning calorimetry (DSC). All diblock copolymers displayed T _g, T _c, and T _m transition temperatures. Their T _g and T _m values increased with the increase of molecular weight of CTA segment. The crystallinity of diblock copolymers increased after isothermal crystallization at 200 °C. Its X-ray analysis revealed that the diblock copolymer had CTA II crystal structure. Thermal analysis supported microphase separation between CTA and oligoamide-15 segments at room temperature, because T _g and T _m values of polyamide-15 are −7 °C and 170–180 °C, respectively.     

Determination of molecular weight distribution of cellulose by conversion into tricarbanilate and fractionation

Two samples of cellulose (molecular weight 2.97 × 10⁵ and 1.25 × 10⁵) were transformed into carbanilates (CTC) which were then fractionated by the elution method at a constant composition of the acetone-water elution mixture with the column temperature gradually increasing from ?30°C to 30°C, and by the GPC method in acetone and tetrahydrofuran. Tetrahydrofuran appeared to be a more suitable solvent. The molecular weights of fractions obtained by the elution fractionation were determined by the light-scattering method in tetrahydrofuran. The width of fractions was determined by the GPC method (average M _w/M _n = 1.37); the [η] values and the Mark-Houwink constants (K = 5.3 × 10^-3, a = 0.84) for tetrahydrofuran at 25°C were determined. The calibration curve for the GP method was constructed by means of the fractions thus obtained; it was demonstrated that the universal calibration curve according to Benoit can also be used. It was demonstrated that the molecular weight distribution of cellulose can be conveniently determined by conversion into CTC followed either by the elution fractionation (for preparative purposes) or by fractionation by the GPC method (for analytical purposes).     

Thermal properties and kinetics of new-generation posterior bulk fill composite cured light-emitting diodes

In this study, the thermal behavior in terms of glass transition (T _g), degradation, and thermal stability of four commercial new-generation posterior bulk fill composites (Surefill SDR, Dentsply; Quixfill, Dentsply; Xtrabase, Voco; and Xtrafill, Voco) activated by light-emitting diodes (LEDs) was analyzed by thermogravimetric analysis (TG), differential scanning calorimetry (DSC), and dynamic mechanical analysis (DMA). The activation energies (E _a) for the decomposition of the dental resins were calculated based on the Kissinger and Doyle kinetic models from the peaks of the endothermic curves obtained when the specimens were heated at four different temperatures (5, 10, 15, and 20 °C min^?1) during DSC. The results show that the Xtrabase composite displayed the highest T _g (120 °C at a 5 °C min^?1 heating rate) and E _a (157.64 kJ mol^?1) values associated with thermal degradation from the main chain of the polymer.     

Microwave Assisted Graft Copolymerization of N-Isopropyl Acrylamide and Methyl Acrylate on Cellulose: Solid State NMR Analysis and CaCO3 Crystallization

Summary: Graft copolymerization of N-isopropyl acrylamide and methyl acrylate on α-cellulose was carried out under microwave irradiation at specific cut off temperatures with cerium (IV) ammonium nitrate and potassium persulfate (KPS) as the initiating system. The role of KPS was to oxidize Ce (III) to Ce (IV) which is the active species in radical formation. The reactions at a temperature cut off of 60 °C were confirmed by ¹³C nuclear magnetic resonance cross-polarization with magic- angle spinning (¹³C NMR CP/MAS) and Fourier-transform infrared spectroscopy (FTIR). The extent of grafting was calculated from weight gain and ¹³C resonances. The grafted cellulose was thermally more stable than the parent cellulose. An attempt to do grafting at a higher cut off temperature of 80 °C was made, however, no grafting was observed from ¹³C NMR CP/MAS but TGA results showed that a cellulose having more thermal stability resulted which was attributed to cross linking. Crystallization of CaCO₃ was carried out using the grafted materials as templates showed better nucleation and different crystal structure was observed.     

Thermogravimetric and FTIR studies of chitosan blends

Results of spectrophotometric and thermogravimetric studies of chitosan (CH) blends with polyvinyl alcohol (PVAL), starch (S) and hydroxypropylcellulose (HPC) obtained by casting from solutions in the form of transparent films containing 0–1.0 weight fraction of CH were discussed. Blends containing S are homogeneous only in the case of low-weight fraction of S (to 0.3).On the basis of results of thermodegradation in dynamic and isothermal conditions, thermal stability of the tested systems was estimated. Thermogravimetric measurements in dynamic conditions were carried out in the temperature range of 100–450 °C at constant heating rate 15 °C/min. From thermogravimetry (TG) and DTG curves the activation energy and characteristic parameters of degradation of the tested blends were determined. The observed growth of activation energy and T_p—temperature of initial weight loss, T_max—temperature of maximal rate and C_e—degree of conversion at the end of the measurement (at temperature 450 °C) along with the increase of polymer fraction (HPC and S) in the CH blend provides an evidence of improved thermal stability of the systems tested.Investigations in isothermal conditions in air at temperature from 100 to 200 °C confirmed appreciable improvement of CH thermal stability in the blends being tested.Infrared spectroscopic analysis of the blends showed a distinct stabilization of the process of chain scission. In the band at 1080 cm⁻¹ associated with absorption in –C–O–C– group during degradation of the blends at temperature 200 °C much smaller decrease due to molecular scission were observed than in the case of pure CH.