纳米多孔双金属氧化物在镍钛合金纤维上的原位生长及其对多环芳烃的选择性固相微萃取

采用阳极氧化法在镍钛合金(NiTi)纤维上原位生长了双金属氧化物纳米孔(NiTiONPs)涂层,通过扫描电镜(SEM)和能谱(EDS)考察了电解质组成和电压对形貌的影响。将NiTiONPs涂层的NiTi纤维与高效液相色谱-紫外检测器联用,研究了4种典型芳香分析物的萃取性能。结果表明,富含TiO2的NiTiONPs涂层对多环芳烃(PAHs)具有良好的萃取效率,尤其对苯并[a]芘的萃取选择性优于市售聚二甲基硅氧烷纤维和聚丙烯酸酯纤维。在优化条件下,PAHs的线性范围为0.05~200μg/L,相关系数均大于0.999,检出限为0.012~0.134μg/L。对单支纤维日内和日间分析的相对标准偏差(RSDs)分别为4.0%~5.5%和6.0%~6.8%,使用分批组装的5支纤维分析的RSDs为6.4%~7.6%。实际水样分析的加标回收率为84.5%~111.5%。所制备NiTi纤维至少可重复使用250次以上,重现性好。     

Oriented ZnO nanoflakes on nickel-titanium alloy fibers for solid-phase microextraction of polychlorinated biphenyls and polycyclic aromatic hydrocarbons

ZnO nanoflakes (ZnONFs) were electrochemically grown on a nickel-titanium alloy (NiTi) wire for use in solid-phase microextraction. Prior to the growth of ZnONFs, the NiTi wire was hydrothermally treated for in-situ growth of TiO₂/NiO nanoflakes as a seeding base. The applied potential was used to control the dimensions of vertically oriented hexagonal ZnONFs. After annealing at 600 °C, the resulting fiber display fairly selective affinity for polychlorinated biphenyls (PCBs) and polycyclic aromatic hydrocarbons. The fibers were applied to the preconcentration of PCBs which then were quantified by HPLC with UV detection. Compared to commercial polydimethylsiloxane coatings, the new coating displays high extraction capability, rapid extraction kinetics and superior cycling stability. This is assumed to be due to its high surface-to-volume ratio, double-sided open access structure, and enhanced structural stability. The assay excels by (a) a wide analytical range (0.10 to 200 μg L^?1 of PCBs), (b) low limits of detection (20–17 ng L^?1), and (c) low standard deviations for the single fiber repeatability (<9.8%) and for the fiber-to-fiber reproducibility (<7.5%). Satisfactory accuracy and precision were achieved when PCBs were determined by this method in spiked rain water, river water and wastewater samples.

Open image in new window

Graphical abstract ZnO nanoflakes were fabricated on a superelastic nickel-titanium alloy wire in desired orientation with enhanced extraction capability and good extraction selectivity. The fabricated fiber was suitable for the determination of PCBs in environmental water samples

     

Hydroxyfullerene as a novel coating for solid-phase microextraction fiber with sol-gel technology

Hydroxyfullerene (fullerol) as a novel coating for solid-phase microextraction (SPME) fiber was first prepared by a sol-gel technology. The coating procedure involving sol solution composition and conditioning process was presented. A fullerene polysiloxane surface-bonded porous coating on the fused-silica fiber surface was obtained and confirmed by IR spectra and scanning electron microscopy. The coating has stable performance at high temperature (even to 360 degrees C) and solvents (organic and inorganic) because of the properties of fullerene and the chemical binding between the coating and the fiber surface. The extraction properties of the new coatings to less volatile organic compounds, such as polychlorinated biphenyls (PCBs), polycyclic aromatic hydrocarbons and polar aromatic amines were investigated using headspace SPME coupled with GC-electron-capture detection and GC-flame ionization detection. In addition, compared with commercial SPME stationary phases, the new coatings showed higher sensitivity, faster velocities of mass transfer for aromatic compound, and possessed planarity molecular recognition for PCBs. Moreover, this fiber was firm, inexpensive, durable and can be prepared simply. The fiber-to-fiber reproducibility was very good.     

A novel silver-coated solid-phase microextraction metal fiber based on electroless plating technique

A novel silver-coated solid-phase microextraction fiber was prepared based on electroless plating technique. Good extraction performance of the fiber for model compounds including phthalate esters (dibutyl phthalate, dioctyl phthalate, dicyclohexyl phthalate and diallyl phthalate) and polycyclic aromatic hydrocarbons (naphthalene, fluorene, phenanthrene, fluoranthene) in aqueous solution was obtained. Under the optimized conditions (extraction temperature, extraction time, ionic strength and desorption temperature), the proposed SPME-GC method showed wide linear ranges with correlation coefficients (R²) ranging from 0.9745 to 0.9984. The limits of detection were at the range of 0.02 to 0.1 μg L⁻¹. Single fiber repeatability and fiber-to-fiber reproducibility as well as stability to acid, alkali and high temperature were studied and the results were all satisfactory. The method was applied successfully to the aqueous extracts of disposable paper cup and instant noodle barrel. Several kinds of analytes were detected and quantified.     

Highly porous silica-polyaniline nanocomposite as a novel solid-phase microextraction fiber coating

A highly porous fiber-coated SBA-15/polyaniline material was prepared for solid-phase microextraction (SPME). The SBA-15/polyaniline nanocomposite was synthesized via chemical polymerization. The prepared SBA-15/polyaniline particles were analyzed by scanning electron microscopy analysis. The prepared nanomaterial was immobilized onto a stainless steel wire for fabrication of the SPME fiber. The fiber was evaluated for the extraction of some polycyclic aromatic hydrocarbons (PAHs) from aqueous sample solutions in combination with gas chromatography-mass spectrometry (GC-MS). In optimum conditions (extraction temperature 60°C, extraction time 40 min, ionic strength 20%, stirring rate: 500 rpm, desorption temperature 260°C, desorption time 2 min), the repeatability for one fiber (n=3), expressed as relative standard deviation (RSD%), was between 5.3 and 8.6% for the test compounds. For deionized water, spiked with selected PAHs, the detection limits for the studied compounds were between 2 and 20 pg/mL.     

Preparation of temperature sensitive molecularly imprinted polymer for solid-phase microextraction coatings on stainless steel fiber to measure ofloxacin

A kind of new temperature sensitive molecularly imprinted polymer (MIP) with ofloxacin (OFL) as template was prepared for the coating of solid phase microextraction (SPME). Dopamine was self-polymerized on stainless steel fiber (SSF) as the SPME support followed by silanization. Then MIP was synthesized as SPME coating on the modified SSF in a capillary, with N-isopropyl acrylamide as temperature sensitive monomer and methacrylic acid as functional monomer. The synthesis could be well repeated with multiple capillaries putting in the same reaction solution. The obtained MIP fiber was evaluated in detail with different techniques and various adsorption experiments. At last the MIP fiber was used to extract the OFL in milk. Satisfied recoveries between 89.7 and 103.4% were obtained with the limit of quantification (LOQ_LC) of 0.04 μg mL⁻¹ by the method of SPME coupled with high performance of liquid chromatography (HPLC).     

Polypyrrole/hexagonally ordered silica nanocomposite as a novel fiber coating for solid-phase microextraction

A highly porous fiber coated polypyrrole/hexagonally ordered silica (PPy/SBA15) materials were prepared for solid-phase microextraction (SPME). The PPy/SBA15 nanocomposite was synthesized by an in situ polymerization technique. The resulting material was characterized by the scanning electron microscopy, thermogravimetric analysis and differential thermal analysis. The prepared nanomaterial was immobilized onto a stainless steel wire for fabrication of the SPME fiber. The fiber was evaluated for the extraction of some polycyclic aromatic hydrocarbons (PAHs) from aqueous sample solutions in combination with gas chromatography-mass spectrometry (GC-MS). A one at-the-time optimization strategy was applied for optimizing the important extraction parameters such as extraction temperature, extraction time, ionic strength, stirring rate, desorption time and desorption temperature. In optimum conditions (extraction temperature 70°C, extraction time 20 min, ionic strength 20% (WV(-1)), stirring rate 500 rpm, desorption temperature 270°C, desorption time 5 min) the repeatability for one fiber (n=3), expressed as relative standard deviation (R.S.D. %), was between 5.0% and 9.3% for the tested compounds. The quantitation limit for the studied compounds were between 13.3 and 66.6 pg mL(-1). The life span and stability of the PPy/SBA15 fiber are good, and it can be used more than 50 times at 260°C without any significant change in sorption properties. The developed method offers the advantage of being simple to use, with shorter analysis times, lower cost of equipment, thermal stability of fiber and high relative recovery in comparison to conventional methods of analysis.     

Role of counteranions in polymeric ionic liquid-based solid-phase microextraction coatings for the selective extraction of polar compounds

A polymeric ionic liquid (PIL) poly(1-vinyl-3-hexylimidazolium chloride) (poly(ViHIm⁺Cl⁻)) was designed as a coating material for solid phase microextraction (SPME) to extract polar compounds including volatile fatty acids (VFAs) and alcohols. The extracted analytes were analyzed by using gas chromatography (GC) coupled with flame ionization detection (FID). Extraction parameters of the HS–SPME–GC–FID method, such as ionic strength, extraction temperature, pH and extraction time were optimized. Calibration studies were carried out under the optimized conditions to further evaluate the performance of the PIL-based SPME coating. For comparison purposes, the PIL poly(1-vinyl-3-hexylimidazolium bis[(trifluoromethyl)sulfonyl]imide) (poly(ViHIm⁺NTf₂⁻)) was also used as the SPME coating to extract the same analytes. The results showed that the poly(ViHIm⁺Cl⁻) PIL coating had higher selectivity towards more polar analytes due to the presence of the Cl⁻ anion which provides higher hydrogen bond basicity than the NTf₂⁻ anion. The limits of detection (LODs) determined by the designed poly(ViHIm⁺Cl⁻) PIL coating ranged from 0.02 μg L⁻¹ for octanoic acid and decanoic acid and 7.5 μg L⁻¹ for 2-nitrophenol, with precision values (as relative standard deviation) lower than 14%. The observed performance of the poly(ViHIm⁺Cl⁻) PIL coating was comparable to previously reported work in which commercial or novel materials were used as SPME coatings. The selectivity of the developed PIL coatings was also evaluated using heptane as the matrix solvent. This work demonstrates that the selectivity of PIL-based SPME coatings can be simply tuned by incorporating different counteranions to the sorbent coating.     

Progress of solid-phase microextraction coatings and coating techniques

Solid-phase microextraction (SPME) has been popular as an environmentally friendly sample pretreatment technique to extract a very wide range of analytes. This is partly owing to the development of SPME coatings. One of the key factors affecting the extraction performances, such as the sensitivity, selectivity, and reproducibility, is the properties of the coatings on SPME fibers. This paper classifies the materials used as SPME coatings and introduces some common preparation techniques of SPME coating in detail, such as sol-gel technique, electrochemical polymerization technique, particle direct pasting technique, restricted access matrix SPME technique, and molecularly imprinted SPME technique.     

Sorbent coatings for solid-phase microextraction based on mixtures of polymeric ionic liquids

Four polymeric ionic liquids based on two different cations, poly(1‐vinyl‐3‐hexylimidazolium) and poly(1‐vinyl‐3‐hexadecylimidazolium), combined with two different anions, bis[(trifluoromethyl)sulfonyl]imide (NTf) and chloride (Cl^?), were combined in various weight percentages and used as sorbent coatings for solid‐phase microextraction gas chromatography (SPME‐GC). The selectivity of the fiber coatings for 12 test analytes was examined. The extraction efficiency of n‐alcohols increased with an increase in the weight percentage of chloride ion in the sorbent coating. The ability to tune the interactions between the coating material and the analytes was exploited and resulted in distinct changes in the limits of detection for hydrogen‐bonding analytes with varying chloride ion content in the sorbent coating.     

Inorganic/organic mesoporous silica as a novel fiber coating of solid-phase microextraction

Mesoporous materials were employed as fast, sensitive and efficient fiber coatings of solid-phase microextraction (SPME) for the first time. Three micrometer as-synthesized C₁₆-MCM-41 particles were immobilized onto stainless steel wire with 100 μm coating thickness. In combination with high performance liquid chromatography (HPLC), extraction efficiency and selectivity of C₁₆-MCM-41 were investigated using aromatic hydrocarbons. Effect of extraction and desorption time, extraction temperature, stirring rate and ionic strength on extraction efficiency were examined. Aanalytical merits of SPME with C₁₆-MCM-41 coating were evaluated. The chromatographic peak area is proportional to the concentration of anthracene in the range 0.5-150 μg l⁻¹. The limit of detection was 0.05 μg l⁻¹ (S/N=3) and the relative standard deviation (R.S.D.) was 0.033%.     

Polydopamine supported preparation method for solid-phase microextraction coatings on stainless steel wire

In this paper, we introduced a novel and versatile route to prepare solid-phase microextraction coatings on the chemically inert stainless steel wire. Polydopamine films can be created on metallic substrates by an oxidant-induced polymerization and subsequently support various secondary reactions to prepare functional surfaces. In the present work, polydopamine-bioactivated stainless steel wire was successfully modified by nanostructured hydroxyapatite. Extraction performance of the fiber was assessed on several polycyclic aromatic hydrocarbons in water solutions. Extraction mechanism was suggested based on the correlation of partition coefficients and LogPs. Both aqueous and solid real life samples were used to test the reliability of the solid-phase microextraction-gas chromatography method; some analytes were detected and quantified.     

Evaluation of a new method for chemical coating of aluminum wire with molecularly imprinted polymer layer. Application for the fabrication of triazines selective solid-phase microextraction fiber

A new solid-phase microextraction (SPME) fiber is fabricated through ultra violet irradiation polymerization of ametryn-molecularly imprinted polymer on the surface of anodized-silylated aluminum wire. The prepared fiber is durable with very good chemical and thermal stability which can be coupled to GC and GC/MS. The effective parameters on the fabrication and application procedures such as spraying mode, ultra violet irradiation (polymerization) time, number of sprayings and polymerizations, pH and ionic strength of sample and extraction time were optimized. This fiber shows high selectivity with great extraction capacity toward triazines. SPME and GC analysis of ametryn, prometryn, terbutryn, atrazine, simazine, propazine and cyanazine using the fabricated fiber result in the detection limits of 9, 32, 27, 43, 51, 74 and 85 ng mL⁻¹, respectively. The reliability of the prepared fiber in real samples has been investigated and proved by using spiked tap water, rice, maize and onion samples.     

Cold fiber solid-phase microextraction device based on thermoelectric cooling of metal fiber

A new cold fiber solid-phase microextraction device was designed and constructed based on thermoelectric cooling. A three-stage thermoelectric cooler (TEC) was used for cooling a copper rod coated with a poly(dimethylsiloxane) (PDMS) hollow fiber, which served as the solid-phase microextraction (SPME) fiber. The copper rod was mounted on a commercial SPME plunger and exposed to the cold surface of the TEC, which was enclosed in a small aluminum box. A heat sink and a fan were used to dissipate the generated heat at the hot side of the TEC. By applying an appropriate dc voltage to the TEC, the upper part of the copper rod, which was in contact to the cold side of the TEC, was cooled and the hollow fiber reached a lower temperature through heat transfer. A thermocouple was embedded in the cold side of the TEC for indirect measurement of the fiber temperature. The device was applied in quantitative analysis of off-flavors in a rice sample. Hexanal, nonanal, and undecanal were chosen as three off-flavors in rice. They were identified according to their retention times and analyzed by GC-flame ionization detection instrument. Headspace extraction conditions (i.e., temperature and time) were optimized. Standard addition calibration graphs were obtained at the optimized conditions and the concentrations of the three analytes were calculated. The concentration of hexanal was also measured using a conventional solvent extraction method (697+/-143ng/g) which was comparable to that obtained from the cold fiber SPME method (644+/-8). Moreover, the cold fiber SPME resulted in better reproducibility and shorter analysis time. Cold fiber SPME with TEC device can also be used as a portable device for field sampling.     

聚甲基苯基乙烯基硅氧烷固相微萃取探头的特性

用溶胶－凝胶及自由基引发交联方法，成功地制备了聚甲基苯基乙烯基聚硅氧烷和羟基硅油复合涂层的固相微萃取探头，与进口商用探头比较，研制的探头对芳香化合物具有高的萃取能力和热稳定性（350℃）以及长的使用寿命。     

Preparation and evaluation of graphene-coated solid-phase microextraction fiber

In this paper, a novel graphene (G) based solid-phase microextraction (SPME) fiber was firstly prepared by immobilizing the synthesized G on stainless steel wire as coating. The new fiber possessed a homogeneous, porous and wrinkled surface and showed excellent thermal (over 330 °C), chemical and mechanical stability, and long lifespan (over 250 extractions). The SPME performance of the G-coated fiber was evaluated in detail through extraction of six pyrethroid pesticides. Although the thickness of G-coated fiber was only 6-8 μm, its extraction efficiencies were higher than those of two commercial fibers (PDMS, 100 μm; PDMS/DVB, 65 μm). This high extraction efficiency may be mainly attributed to huge delocalized π-electron system of G, which shows strong π-stacking interaction with pyrethroid pesticide. The G-coated fiber was applied in the gas chromatographic determination of six pyrethroids, and their limits of detection were found to be ranged from 3.69 to 69.4 ng L⁻¹. The reproducibility for each single fiber was evaluated and the relative standard deviations (RSDs) were calculated to be in the range from 1.9% to 6.5%. The repeatability of fiber-to-fiber and batch-to-batch was 4.3-9.2% and 4.1-9.9%. The method developed was successfully applied to three pond water samples, and the recoveries were 83-110% at a spiking of 1 μg L⁻¹.     

A novel sol-gel-based amino-functionalized fiber for headspace solid-phase microextraction of phenol and chlorophenols from environmental samples

A novel amino-functionalized polymer was synthesized using 3-(trimethoxysilyl) propyl amine (TMSPA) as precursor and hydroxy-terminated polydimethylsiloxane (OH-PDMS) by sol–gel technology and coated on fused-silica fiber. The synthesis was designed in a way to impart polar moiety into the coating network. The scanning electron microscopy (SEM) images of this new coating showed the homogeneity and the porous surface structure of the film. The efficiency of new coating was investigated for headspace solid-phase microextraction (SPME) of some environmentally important chlorophenols from aqueous samples followed by gas chromatography–mass spectrometry (GC–MS) analysis. Effect of different parameters influencing the extraction efficiency such as extraction temperature, extraction time, ionic strength and pH was investigated and optimized. In order to improve the separation efficiency of phenolic compounds on chromatography column all the analytes were derivatized prior to extraction using acetic anhydride at alkaline condition. The detection limits of the method under optimized conditions were in the range of 0.02–0.05 ng mL⁻¹. The relative standard deviations (R.S.D.) (n = 6) at a concentration level of 0.5 ng mL⁻¹ were obtained between 6.8 and 10%. The calibration curves of chlorophenols showed linearity in the range of 0.5–200 ng mL⁻¹. The proposed method was successfully applied to the extraction from spiked tap water samples and relative recoveries were higher than 90% for all the analytes.