Organic transistors in the new decade: Toward n-channel,printed, and stabilized devices

Significant progress has been made in designing organic semiconducting materials (OSCs) for the past few decades for organic field-effect transistors (OFETs). Much attention has been paid to the development of p-channel OSCs, with less but highly significant progress on n-channel OSCs. In this review, we focus on the advances made with OFETs in the last few years to achieve high performance in n-channel modes, air stability, and solution processability, leading to printable active electronics. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2012     

Corannulene derivatives for organic electronics: From molecular engineering to applications

This paper intends to provide an overview for using corannulene derivatives in organic electronics such as organic field-effect transistors (OFETs), organic solar cells (OSCs), and organic light-emitting diodes (OLEDs). We highlight the rational design strategies, tuning molecular orbital energy levels and arrangement in single crystals of corannulenes. The topological structure and properties of corannulene make it a unique candidate for organic electronics.     

High electron mobility fluorinated indacenodithiophene small molecule acceptors for organic solar cells

Indacenodithiophene (IDT) derivatives are kinds of the most representative and widely used cores of small molecule acceptors (SMAs) in organic solar cells (OSCs). Here we systematically investigate the influence of end-group fluorination density and position on the photovoltaic properties of the IDT-based SMAs IDIC-nF (n = 0, 2, 4). The absorption edge of IDIC-nF red-shifts with the π-π stacking and crystallinity improvement, and their electronic energy levels downshift with increasing n. Due to the advantages of J_sc and FF as well as acceptable V_oc, the difluorinated IDIC-2F acceptor based OSCs achieve the highest power conversion efficiency (PCE) of 13%, better than the OSC devices based on IDIC and IDIC-4F as acceptors. And the photovoltaic performance of the PTQ10: IDIC-2F OSCs is insensitive to the active layer thickness: PCE still keep high values of 12.00% and 11.46% for the devices with active layer thickness of 80 and 354 nm, respectively. This work verifies that fine and delicate modulation of the SMAs molecular structure could optimize photovoltaic performance of the corresponding OSCs. Meanwhile, the thickness-insensitivity property of the OSCs has potential for large-scale and printable fabrication technology.     

Insulating Polymers as Additives to Bulk-Heterojunction Organic Solar Cells: The Effect of Miscibility

Adding insulating polymers to conjugated polymers is an efficient strategy to tailor their mechanical properties for flexible organic electronics. In this work, we selected two insulating polymers as additives for high-performance photoactive layers and investigated the mechanical and photovoltaic properties in organic solar cells (OSCs). The insulating polymers were found to reduce the electron mobilities in the photoactive layers, and hence the power conversion efficiencies were significantly decreased. More importantly, we found that the insulating polymers exhibited negative effect on the mechanical properties of the photoactive layers, with reduced Young's modulus and low crack onset strains. Further studies revealed that the insulating polymers had poor miscibility with the photoactive layers, providing large domains and more cavities in blend thin films, which act as negative effect for the tensile test. The studies indicate that rational selection of insulating polymers, especially enhancing the non-covalent interaction with the photoactive layers, will be critically important for the stretchable OSCs.     

Anisotropic charge carrier transport of optoelectronic functional selenium-containing organic semiconductor materials

Organic semiconductors (OSCs) materials are currently under intense investigation because of their potential applications such as organic field-effect transistors, organic photovoltaic devices, and organic light-emitting diodes. Inspired by the selenization strategy can promote anisotropic charge carrier migration, and selenium-containing compounds have been proved to be promising materials as OSCs both for hole and electron transfer. Herein, we now explore the anisotropic transport properties of the series of selenium-containing compounds. For the compound containing Se Se bond, the Se Se bond will break when attaching an electron, thus those compounds cannot act as n-type OSCs. About the different isomer compounds with conjugated structure, the charge transfer will be affected by the stacking of the conjugated structures. The analysis of chemical structure and charge transfer property indicates that Se-containing materials are promising high-performance OSCs and might be used as p-type, n-type, or ambipolar OSCs. Furthermore, the symmetry of the selenium-containing OSCs will affect the type of OSCs. In addition, there is no direct relationship between the R groups with their performance, whether it or not as p-type OSCs or n-types. This work demonstrates the relationship between the optoelectronic function and structure of selenium-containing OSCs materials and hence paves the way to design and improve optoelectronic function of OSCs materials.     

Self-Doped n-Type Quinoidal Compounds with Good Air Stability and High Electrical Conductivity for Organic Electronics

Air stable n-type conductive molecules with high electrical conductivities and excellent device performance have important applications in organic electronics, but their synthesis remains challenging. Herein, we report three self-doped n-type conductive molecules, designated QnNs, with a closed-shell quinoidal backbone and alkyl amino chains of different lengths. The QnNs are self-doped by intermolecular electron transfer from the amino groups to the quinoidal backbone. This process is ascertained unambiguously by experiments and theoretical calculations. The use of a quinoidal structure effectively improves the self-doping level, and thus increases the electrical conductivity of self-doped n-type conductive molecules achieved by a closed-shell structure from<10⁻⁴ S cm⁻¹ to>0.03 S cm⁻¹. Furthermore, the closed-shell quinoidal structure results in good air stability of the QnNs, with half-lives>73 days; and Q4N shows an electrical conductivity of 0.019 S cm⁻¹ even after exposure to air for 120 days. When applying Q6N as the cathode interlayer in organic solar cells (OSCs), an outstanding power conversion efficiency of up to 18.2 % was obtained, which represents one the best results in binary OSCs.     

Naphthalene-Diimide-Based Ionenes as Universal Interlayers for Efficient Organic Solar Cells

Self-doping ionene polymers were efficiently synthesized by reacting functional naphthalene diimide (NDI) with 1,3-dibromopropane ( NDI-NI ) or trans-1,4-dibromo-2-butene ( NDI-CI ) via quaternization polymerization. These NDI-based ionene polymers are universal interlayers with random molecular orientation, boosting the efficiencies of fullerene-based, non-fullerene-based, and ternary organic solar cells (OSCs) over a wide range of interlayer thicknesses, with a maximum efficiency of 16.9 %. NDI-NI showed a higher interfacial dipole (Δ), conductivity, and electron mobility than NDI-CI , affording solar cells with higher efficiencies. These polymers proved to efficiently lower the work function (WF) of air-stable metals and optimize the contact between metal electrode and organic semiconductor, highlighting their power to overcome energy barriers of electron injection and extraction processes for efficient organic electronics.     

Printable SnO2 cathode interlayer with up to 500 nm thickness-tolerance for high-performance and large-area organic solar cells

The printable electrode interlayer with excellent thickness tolerance is crucial for mass production of organic solar cells(OSCs)by solution-based print techniques. Herein, high-quality printable SnO_2 films are simply fabricated by spin-coating or bladecoating the chemical precipitated SnO_2 colloid precursor with post thermal annealing treatment. The SnO_2 films possess outstanding optical and electrical properties, especially extreme thickness-insensitivity. The interfacial electron trap density of SnO_2 cathode interlayers(CILs) are very low and show negligible increase as the thicknesses increase from 10 to 160 nm,resulting in slight change of the power conversion efficiencies(PCEs) of the PM6:Y6 based OSCs from 16.10% to 13.07%. For blade-coated SnO_2 CIL, the PCE remains high up to 12.08% even the thickness of SnO_2 CIL is high up to 530 nm. More strikingly, the large-area OSCs of 100 mm~2 with printed SnO_2 CILs obtain a high efficiency of 12.74%. To the best of our knowledge, this work presents the first example for the high-performance and large-area OSCs with the thickness-insensitive SnO_2 CIL.     

Crystallization Mechanism of 9,9-Diphenyl-dibenzosilole from Solids

Organic semiconductor (OSC) crystals have great potential to be applied in many fields, as they can be flexibly designed according to the demands and show an outstanding device performance. However, OSCs with the capacity of solid-state crystallization (SSC) are developing too slowly to meet demands in productions and applications, due to their difficulties in molecular design and synthesis, unclear mechanism and high dependence on experimental conditions. In this work, in order to solve the problems, we synthesized an organic semiconductor capable of SSC at room temperature by adjusting the relationship between conjugated groups and functional groups. The thermodynamic and kinetic properties have been studied to discover the model of film SSC. Moreover, it can be purposefully controlled to prepare the high-quality crystals, and their corresponding organic electronic devices were further fabricated and discussed.     

Critical Role of Molecular Electrostatic Potential on Charge Generation in Organic Solar Cells

Revealing the charge generation is a crucial step to understand the organic photovoltaics. Recent development in non‐fullerene organic solar cells (OSCs) indicates efficient charge separation even with negligible energetic offset between the donor and acceptor materials. These new findings trigger a critical question concerning the charge separation mechanism in OSCs, traditionally believed to result from sufficient energetic offset between the polymer donor and fullerene acceptor. We propose a new mechanism, which involves the molecular electrostatic potential, to explain efficient charge separation in non‐fullerene OSCs. Together with the new mechanism, we demonstrate a record efficiency of ~12% for systems with negligible energetic offset between donor and acceptor materials. Our analysis also rationalizes different requirement of the energetic offset between fullerene‐based and non‐fullerene OSCs, and paves the way for further design of OSC materials with both high photocurrent and high photovoltage at the same time.     

Progress of pyrene-based organic semiconductor in organic field effect transistors

Thanks to the pure blue emitting, high planarity, electron rich and ease of chemical modification, pyrene has been thoroughly investigated for applications in organic electronics such as organic light emitting diodes (OLEDs), organic field effect transistors (OFETs), and organic solar cells (OSCs). Especially, great progresses have been made of pyrene-based organic semiconductors for OFETs in past decades. Due to the difference of molecular structure, pyrene-based organic semiconductors are divided into three categories, pyrene as terminal group, pyrene as center core and fused pyrene derivatives. This minireview gives a brief introduction of the structure-property relationship and application in OFETs about most of pyrene-based semiconducting materials since 2006, illustrating that pyrene is a good building block to construct semiconductors with superior transport property for OFETs. Finally, we provide a summary concerning the methodology to improve the transport property of the pyrene-based semiconducting materials as well as an outlook.     

Potential of Nonfullerene Small Molecules with High Photovoltaic Performance

Over the past decades, fullerene derivatives have become the most successful electron acceptors in organic solar cells (OSCs) and have achieved great progress, with power conversion efficiencies (PCEs) of over 11 %. However, fullerenes have some drawbacks, such as weak absorption, limited energy‐level tunability, and morphological instability. In addition, fullerene‐based OSCs usually suffer from large energy losses of over 0.7 eV, which limits further improvements in the PCE. Recently, nonfullerene small molecules have emerged as promising electron acceptors in OSCs. Their highly tunable absorption spectra and molecular energy levels have enabled fine optimization of the resulting devices, and the highest PCE has surpassed 12 %. Furthermore, several studies have shown that OSCs based on small‐molecule acceptors (SMA) have very efficient charge generation and transport efficiency at relatively low energy losses of below 0.6 eV, which suggests great potential for the further improvement of OSCs. In this focus review, we analyze the challenges and potential of SMA‐based OSCs and discuss molecular design strategies for highly efficient SMAs.     

Single-wall carbon nanotube-containing cathode interfacial materials for high performance organic solar cells

Water/alcohol soluble cathode interfacial materials(CIMs)are playing important roles in optoelectronic devices such as organic light emitting diodes,perovskite solar cells and organic solar cells(OSCs).Herein,n-doped solution-processable single-wall carbon nanotubes(SWCNTs)-containing CIMs for OSCs are developed by dispersing SWCNTs to the typical CIMs perylene diimide(PDI)derivatives PDIN and PDINO.The Raman and X-ray photoelectron spectroscopy(XPS)measurement results illustrate the ndoped behavior of SWCNTs by PDIN/PDINO in the blend CIMs.The blended and n-doped SWCNTs can tune the work function and enhance the conductivity of the PDI-derivative/SWCNT(PDI-CNT)composite CIMs,and the composite CIMs can regulate and down-shift the work function of cathode,reduce the charge recombination,improve the charge extraction rate and enhance photovoltaic performance of the OSCs.High power conversion efficiency(PCE)of 17.1%and 17.7%are obtained for the OSCs based on PM6:Y6 and ternary PM6:Y6:PC₇₁ BM respectively with the PDI-CNTcomposites CIMs.These results indicate that the ndoped SWCNT-containing composites,like other n-doped nanomaterials such as zero dimensional fullerenes and two dimensional graphenes,are excellent CIMs for OSCs and could find potential applications in other optoelectronic devices.     

Rylene diimide and dithienocyanovinylene copolymers for polymer solar cells

Two polymers containing(E)-2,3-bis(thiophen-2-yl)acrylonitrile(CNTVT) as a donor unit, perylene diimide(PDI) or naphthalene diimide(NDI) as an acceptor unit, are synthesized by the Stille coupling copolymerization, and used as the electron acceptors in the solution-processed organic solar cells(OSCs). Both polymers exhibit broad absorption in the region of 300–850 nm. The LUMO energy levels of the resulted polymers are ca. –3.93 eV and the HOMO energy levels are –5.97 and –5.83 eV. In the binary blend OSCs with PTB7-Th as a donor, PDI polymer yields the power conversion efficiency(PCE) of up to 1.74%, while NDI polymer yields PCE of up to 3.80%.     

Naphthalene‐Diimide‐Based Ionenes as Universal Interlayers for Efficient Organic Solar Cells

Self‐doping ionene polymers were efficiently synthesized by reacting functional naphthalene diimide (NDI) with 1,3‐dibromopropane ( NDI‐NI ) or trans‐1,4‐dibromo‐2‐butene ( NDI‐CI ) via quaternization polymerization. These NDI‐based ionene polymers are universal interlayers with random molecular orientation, boosting the efficiencies of fullerene‐based, non‐fullerene‐based, and ternary organic solar cells (OSCs) over a wide range of interlayer thicknesses, with a maximum efficiency of 16.9 %. NDI‐NI showed a higher interfacial dipole (Δ), conductivity, and electron mobility than NDI‐CI , affording solar cells with higher efficiencies. These polymers proved to efficiently lower the work function (WF) of air‐stable metals and optimize the contact between metal electrode and organic semiconductor, highlighting their power to overcome energy barriers of electron injection and extraction processes for efficient organic electronics.     

Scanning tunneling microscopy of functional nanostructures on solid surfaces: Manipulation,self-assembly,and applications

The manipulation, self-assembly, and application of functional nanostructures on solid surfaces are fundamental issues for the development of electronics and optoelectronics. For a future molecular electronics the fabrication of high-quality organic thin films on metal surfaces is crucial, which can be achieved by thermal evaporation for various organic/metal systems. The switching property of single molecules can be manipulated and measured, revealing a possibility to realize single molecular devices. Manipulation of a local conductance transition in organic thin films, used for ultra-high density data storage, has also been achieved based on several different mechanisms. The stability, reversibility, and repeatability of the local conductance transition have been improved by molecular design. In this article, we will summarize our recent scanning tunneling microscopy studies on these issues and discuss their perspectives.     

Carbazolebis(thiadiazole)-core based non-fused ring electron acceptors for efficient organic solar cells

Non-fused ring electron acceptors (NFREAs) have a broad application prospect in the commercialization of organic solar cells (OSCs) due to the advantages of simple synthesis and low cost. The selection of intermediate block cores of non-fused frameworks and the establishment of the relationship between molecular structure and device performance are crucial for the realization of high-performance OSCs. Herein, two A-D-A’-D-A type NFREAs namely CBTBO-4F and CBTBO-4Cl, constructed with a novel electron-deficient block unit N-(2-butyloctyl)-carbazole[3,4-c:5,6-c]bis[1,2,5]thiadiazole (CBT) and bridging unit 4,4-bis(2-ethylhexyl)-4H-cyclopenta[2,1-b:3,4-b']dithiophene (DTC) coupling with different terminals (IC-2F/2Cl), were designed and synthesized. The two NFREAs feature broad and strong photoresponse from 500 nm to 900 nm due to the strong intramolecular charge transfer characteristics. Compared with CBTBO-4F, CBTBO-4Cl shows better molecular planarity, stronger crystallinity, more ordered molecular stacking, larger van der Waals surface, lower energy level and better active layer morphology, contributing to much better charge separation and transport behaviors in its based devices. As a result, the CBTBO-4Cl based device obtains a higher power conversion efficiency of 10.18% with an open-circuit voltage of 0.80 V and a short-circuit current density of 21.20 mA/cm². These results not only demonstrate the great potential of CBT, a new building block of the benzothiazole family, in the construction of high-performance organic conjugated semiconductors, but also suggest that the terminal chlorination is an effective strategy to improve device performance.     

Unfused Nonfullerene Acceptors Based on Simple Dipolar Merocyanines

Merocyanine (MC) dyes exhibit facile synthesis and attractive optical properties, making them widely studied as the donor materials in organic solar cells (OSCs). In this study, for the first time, simple indole-based MCs are successfully designed as unfused nonfullerene acceptors (NFAs) for OSCs by forming dimers with A−D-π-D−A structure, which possess enhanced photostability compared to the well-known ITIC acceptor and high electron mobility in blend films. When blended with P3HT donor, one of the dimers, i. e. Z2, shows a good cell efficiency of 3.53 %, which outperforms the performance of most of P3HT/NFA blends, particularly for unfused systems, and thus indicates good potential of simple MCs as NFAs.     

It's in the Fine Print: Erasable Three‐Dimensional Laser‐Printed Micro‐ and Nanostructures

3D printing, on all scales, is currently a vibrant topic in scientific and industrial research as it has enormous potential to radically change manufacturing. Owing to the inherent nature of the manufacturing process, 3D printed structures may require additional material to structurally support complex features. Such support material must be removed after printing—sometimes termed subtractive manufacturing—without adversely affecting the remaining structure. An elegant solution is the use of photoresists containing labile bonds that allow for controlled cleavage with specific triggers. Herein, we explore state‐of‐the‐art cleavable photoresists for 3D direct laser writing, as well as their potential to combine additive and subtractive manufacturing in a hybrid technology. We discuss photoresist design, feature resolution, cleavage properties, and current limitations of selected examples. Furthermore, we share our perspective on possible labile bonds, and their corresponding cleavage trigger, which we believe will have a critical impact on future applications and expand the toolbox of available cleavable photoresists.     

Organic solar cells based on small molecule donor and polymer acceptor

Small molecule donor/polymer acceptor(SD/PA)-type organic solar cells(OSCs) have attracted widespread attention in recent years due to the continuing power conversion efficiency(PCE) growth, near 10%, and the excellent thermal stability for the practical applications. However, the development of SD/PA-type OSCs lags far behind that of polymer donor/small molecule acceptor(PD/SA)-type OSCs, which are also based on the combination of small molecule and polymer, with the PCEs exceeding 18%. The rea...