Evaluation and correction of isotope ratio inaccuracy on inductively coupled plasma time-of-flight mass spectrometry

Isotope ratio measurements are found to have systematic bias when using the analog detection mode on an inductively coupled plasma time-of-flight (TOF) mass spectrometer. This bias is dependent upon the value of the ratio, the intensity of the signal, and the gain of the electron multiplier tube. The error should not appear if ion counting is employed instead of analog detection, although analog detection with time-of-flight has other distinct advantages. The cause of this isotope ratio inaccuracy is rooted in disproportionate recording of the analog signal because of the need to filter out noise by blocking analog signals below a threshold voltage. This attenuates smaller signals to a greater degree than larger signals. This variable “detection efficiency” causes a larger systematic error in the isotopic ratio as the isotopic abundances become more disparate. Ratios close to unity are generally accurate within the precision of the measurement. The use of an increased gain on the detector leads to improved ratio accuracy, but at the cost of decreased detector lifetime. This research presents a method of analyzing solutions using natural, known isotopic ratios to produce an efficiency correction curve. The average error of several isotope ratios for a 500 ng/mL solution of various elements with ratios between 3.4 and 10 was found to be 6.5% without correction, 3.0% with increased detector gain, 1.1% with efficiency correction and 0.6% with both increased gain and efficiency correction.     

Parametric evaluation of laser ablation and ionization time-of-flight mass spectrometry with ion guide cooling cell

A novel laser ablation and ionization time-of-flight mass spectrometer has been used for direct elemental analysis of alloys. The system was incorporated with an ion guide cooling cell to reduce the kinetic energy distribution for the purpose of better resolution. Parametric studies have been conducted on the system with respect to the buffer gas pressure and the distance from sample to the nozzle to obtain the maximal signal intensities. In order to obtain satisfactory relative sensitivity coefficients (RSC) for different elements, the influence of the laser irradiance, nozzle voltage, rf frequency and voltage of the hexapole were also investigated. Under the optimized conditions, the RSC of different elements were available for direct semi-quantitative analysis. The mass resolving power (FWHM) of the spectrometer was approximately 7000 (m/Δm) and the limit of detection (LOD) was 10^− 6 g/g.     

Application of a New pH‐Sensitive Electrode as a Detector in Flow Injection Potentiometry

A new pH sensitive detector for flow‐through potentiometry was developed on the basis of a graphite/quinhydrone composite electrode. The detector was constructed of two polymethylmethacrylate plates between which a 0.1 mm thick sensitive layer is situated. After drilling a hole through the plates, a ring of the sensitive layer is exposed to the solution stream. A conventional calomel reference electrode was placed downstream following the flow‐through sensor. The response behavior in different electrolyte solutions was investigated. The detector shows a Nernstian behavior for injections of hydrochloric acid into a KCl background solution as well as for the steady state response in concentration step experiments using hydrochloric acid and buffer solutions. The response time is sufficiently short for FIA applications (T₉₅ between 3 and 5.4 s). The influences of flow rate and injection volume on the detector signal are discussed.     

Monitoring CP-93,393 reaction mixtures by flow-injection analysis-mass spectrometry

CP-93,393 is a drug candidate at Pfizer. Flow-injection analysis-mass spectrometry (FIA-MS) was used to monitor reaction completion for CP-93,393 reaction mixtures. FIA-MS provides essentially instantaneous results, is relatively simple to operate, and is a universal system that can be used to monitor any reaction as long as the product has a molecular weight that differs from the molecular weights of the reactants. The mass spectrometer for these studies employed atmospheric pressure chemical ionization. Samples were introduced into the mass spectrometer with a flowing stream of solvent.     

Optimization of instrumental parameters for flow injection analysis-thermospray tandem mass spectrometry

Summary Optimization of signal-to-noise ratios (S/N) by optimizing electron multiplier (EM) voltage and resolution of the first and second mass analyser in a thermospray (TSP), tandem mass spectrometer system is studied. Using flow injection analysis (FIA) of samples containing eight chlorophenoxy carboxylic acid herbicides and bentazone, and a FIA system, the signal and background (noise) intensity i.e. S/N are studied with selected reaction monitoring (SRM) at different EM voltages. An EM voltage of 2500 V improves the S/N ratios 5.5–13 fold compared to the usual 1700 V. Applying additional resolution voltages of +3 to +4 V to the first and second mass analyser decreases resolution in each mass analyser, but there is no overall loss in selectivity, while the S/N ratios further increase 3–4 fold. The selectivity of measurements was studied using 2,4,5-T ((2,4,5-trichlorophenoxy)acetic acid) and triclopyr, which differ only one mass unit in the selection of the parent and daughter ion mass in the applied SRM method. Resolution could be decreased to 36–54% valley definition, while still ensuring the selectivity. With the herbicides studied, screening of surface water samples spiked at the 1 g l^–1 level, corresponding to 25 pg component s^–1 into the MS, is easily achieved under optimum conditions without analyte concentration. Some sample clean-up is recommended, however, because ionization efficiencies tend to diminish with some of the raw sample studied.     

Enhanced mass resolution tandem mass spectrometry method for 2,3,7,8-tetrachlorodibenzo-p-dioxin detection with ion trap mass spectrometry using high damping gas pressure

Damping gas flow was optimized for 2,3,7,8-tetrachlorodibenzo-p-dioxin (TCDD) determination using ion trap mass spectrometer. A tandem mass spectrometry (MS-MS) method with better than unit-mass resolution (mass width, 0.3 u) was developed at a damping gas flow of 1.5 ml/min and a collision-induced dissociation (CID) voltage of 3.30 V. The relative standard deviation (R.S.D.) at the enhanced resolution was 2.9% in 24 h of consecutive injections. The detection limit was significantly improved because the efficiency of both precursor ion trapping and fragmentation increased with the damping gas flow. Product ion yield was 4.5 times higher and limit of detection was 3.2 times lower than at the default flow (0.3 ml/min and 1.65 V).     

Continuum background in inductively coupled plasma mass spectrometry

A laboratory constructed ICP mass spectrometer has been studied to reduce the continuum background to achieve better signal to background ratios. An optical baffle plate of 6 mm diameter is found to be the best with a cone-like lens cap of 8 mm diameter. Varying the operating conditions for the plasma and mass spectrometer affect the background intensity. Increasing the voltages applied to the ion lens elements always increases the background. A weak discharge in the lens elements is considered as the cause of the increase. The variation of background with the voltage applied to the ion deflector placed in front of the detector suggests that charged species partly contribute continuum background. Detection limits for several elements under compromised conditions are reported.     

Tracing of surfactants in the biological wastewater treatment process and the identification of their metabolites by flow injection-mass spectrometry and liquid chromatography-mass spectrometry and -tandem mass spectrometry

Results of aerobic biodegradation of alkyl ethoxylates (AEOs), of nonylphenol polyethoxylates (NPEOs), and of NPEO derivatives (sulfonates and sulfates), as well as anaerobic NPEO biodegradation monitored by flow injection analysis (FIA) or liquid chromatographic separation (LC) in combination with mass (MS) and tandem mass spectrometry (MS-MS) are presented. The application of visual pattern recognition in the FIA-MS mode showed quite different degradation pathways for C13-AEOs, so that aldehyde compounds as metabolites could be confirmed by collision-induced dissociation for the first time. Methyl ethers of AEO compounds were found to be persistent under aerobic conditions, while NPEO degradation resulted in nonylphenol polyether carboxylates. FIA- and LC-MS proved that NPEO derivatives used as anionic surfactants were either non-biodegradable (nonylphenol diethoxy sulfonate) or were primarily degraded (nonylphenol polyethoxy sulfates) into compounds of the same molar masses yet of different retention behaviour. Anaerobic degradation of NPEOs led to the generation of nonylphenols, which was confirmed by GC-MS.     

Investigation of analytical variation in metabonomic analysis using liquid chromatography/mass spectrometry

Sources of analytical variation in high-performance liquid chromatography/mass spectrometry (HPLC/MS), such as changes in retention, mass accuracy or signal intensity, have been investigated to assess their importance as a variable in the metabonomic analysis of human urine. In this study chromatographic retention and mass accuracy were found to be quite reproducible with the most significant source of analytical variation in the data sets obtained being the result of changes in detector response. Depending on the signal intensity threshold used to define the presence of a peak a sample component could be present in some replicate injections and absent in others within the same run. The implementation of a more sophisticated data software analysis package was found to greatly reduce the impact of detector response variability resulting in improved data analysis.     

Flow injection analysis for residual chlorine using Pb(II) ion-selective electrode detector

A simple flow injection analysis (FIA) system for residual chlorine in tap water has been developed by using a Pb(II) ion-selective electrode (ISE) detector. The method is based on a specific response of the Pb(II)-ISE to residual chlorine. The FIA system consists of a millivolt meter, a peristaltic pump, a Pb(II)-ISE detector and a recorder. A linear working curve between peak height and concentration of residual chlorine was obtained from 0.1 to 1 mg l(-1) for the developed FIA system. The relative standard deviation for repeated injections of a 0.2 mg l(-1) residual chlorine sample was 2%. The regression line and its correlation factor between the conventional o-tolidine colorimetric method and the present method were Y=0.75X+0.17 and 0.967, respectively, for this determination.     

Signal suppression in electrospray ionization Fourier transform mass spectrometry of multi-component samples

The high resolution, mass range and sensitivity of Fourier transform mass spectrometry (FTMS) suggest that it could be a valuable tool for the quantitative analysis of biomolecules. To determine the applicability of electrospray ionization combined with FTMS to the quantitation of biomolecules in multi-component samples, mixtures of varying compositions and concentrations of cytochrome c, angiotensin II, insulin and chicken egg white lysozyme were examined. The instrument used has an electrospray source with a hexapole trap to accumulate ions for injection into an ion cyclotron resonance mass analyzer. Linear responses for single component samples of angiotensin II and insulin were in the range 0.031-3 microM and those of both cytochrome c and lysozyme were between 0.031 and 1 microM. In examining various mixtures of the proteins with angiotensin II, it was found that the presence of the large molecules suppresses the signal of the smaller molecules. This is suggested to be a result of ion-ion interactions producing selective ion loss from either the hexapole trap or the ion cyclotron resonance mass analyzer trap. More massive, more highly charged ions can collisionally transfer large amounts of translational energy to smaller, less highly charged ions, ejecting the smaller ions from the trap. Mass discrimination effects resulting from the trapping voltage were also examined. It was found that relative signal intensities of ions of different masses depend on trapping voltage for externally produced ions. The effect is most significant for spectra including masses that differ by 30% or more. This suggests that for quantitation all samples and standards be run at a constant trapping potential.     

Effect of the mobile phase composition on the separation and detection of intact proteins by reversed-phase liquid chromatography-electrospray mass spectrometry

Various buffers (ammonium acetate, ammonium formate, and ammonium hydrogencarbonate), acids (formic acid, acetic acid, heptafluorobutyric acid, and trifluoroacetic acid), and bases (ammonium hydroxide and morpholine) covering the range from 2 to 11.5 have been investigated for their performance in the separation of proteins by reversed-phase liquid chromatography (RPLC) and in their detection by electrospray mass spectrometry (ESI-MS). These additives were first tested for the detection of standard proteins by ESI-MS by flow-injection analysis (FIA). Those additives yielding the highest signals were employed for the separation of standard proteins by using three different reversed-phase columns: two C18 columns (4.6 mm I.D. and 2.1 mm I.D.) and one perfusion column (2 mm I.D.). The sensitivity of the LC-MS system was evaluated with the column giving the best results and with those LC eluents enabling the LC separation of the proteins and also yielding the highest MS signals. For that purpose, calibration curves were compared for both LC-MS and FIA-MS. Formic acid was the additive yielding the highest responses in FIA-MS and trifluoroacetic acid (TFA) gave the best separation and recovery of the proteins. However, problems related to poor recovery of the proteins in the column when formic acid was used and the significant signal suppression observed in MS when TFA was employed, made neither of them suitable for the sensitive detection of the proteins in LC-MS.     

Assessment of the pollutant elimination efficiency by gas chromatography/mass spectrometry, liquid chromatography-mass spectrometry and -tandem mass spectrometry. Comparison of conventional and membrane-assisted biological wastewater treatment processes

The elimination efficiency of advanced conventional biological wastewater treatment was compared to membrane-assisted biological wastewater treatment. The sum parameter analyses dissolved organic carbon (DOC) and chemical oxygen demand (COD) or substance-specific analyses such as gas chromatography combined with mass spectrometry, flow injection analysis (FIA-MS) and liquid chromatography (LC-MS) in combination with mass or tandem mass spectrometry (MS-MS) were applied to assess elimination of hardly eliminable compounds in both types of wastewater treatment plants (WWTP). Reduction of DOC and COD in wastewater treatment processes confirmed a favourable elimination efficiency. Substance-specific methods which were applied in addition permitted a qualitative and semi-quantitative assessment of elimination with a visual pattern recognition approach. In order to identify pollutants either the NIST library of electron impact mass spectra for unpolar compounds or the laboratory-made collision-induced dissociation spectra library for polar pollutants was used. To assess elimination efficiency FIA-MS in the selected ion monitoring mode (SIM) besides high selective substance-specific mass spectrometric techniques such as parent ion scans and neutral loss scans were used for quantification. Results proved that membrane-assisted treatment was more effective than advanced biological treatment. In both types of WWTPs predominantly unpolar pollutants were eliminated, while all effluents were dominated by polar compounds of anthropogenic and biogenic origin. These unpolar and polar compounds which had been identified as hardly eliminable are reported about. Quantitative results obtained by FIA-MS, LC-MS and MS-MS for the elimination of alkyl polyglycol ethers, nonylphenol ethoxylates and linear alkylbenzenesulfonic acids from wastewater are presented.     

Flow-injection analysis based on a membrane separation module and a bulk acoustic wave impedance sensor – determination of the volatile acidity of fermentation products

A novel flow-injection analysis (FIA) system has been developed for the rapid determination of the volatile acidity of some fermentation products like vinegars and juices. The proposed method is based on the diffusion of volatile acids, mainly acetic acid, across a PTFE gas-permeable membrane from an acid stream into an alkaline stream, and the acids trapped in the acceptor solution are determined online by a bulk acoustic wave impedance sensor based on changes in the conductivity of the solution. It exhibited a linear frequency response up to 10 mmol · L^–1 acetic acid with a detection limit of 50 μmol · L^–1, and the precision was better than 1% (RSD) at a through-put of 72 h^–1. The effects of operating voltage for the detector, cell constant of the electrode, composition of acceptor stream, flow rates and temperature on the FIA performance were also investigated.     

Design and optimization of on-chip capillary electrophoresis

We present a systematic, experimentally validated method of designing electrokinetic injections for on-chip capillary electrophoresis applications. This method can be used to predict point-wise and charge-coupled device (CCD)-imaged electropherograms using estimates of species mobilities, diffusivities and initial sample plug parameters. A simple Taylor dispersion model is used to characterize electrophoretic separations in terms of resolution and signal-to-noise ratio (SNR). Detection convolutions using Gaussian and Boxcar detector response functions are used to relate optimal conditions for resolution and signal as a function of relevant system parameters including electroosmotic mobility, sample injection length, detector length scale, and the length-to-detector. Analytical solutions show a tradeoff between signal-to-noise ratio and resolution with respect to dimensionless injection width and length to the detector. In contrast, there is no tradeoff with respect to the Peclet number as increases in Peclet number favor both SNR and separation solution (R). We validate our model with quantitative epifluorescence visualizations of electrophoretic separation experiments in a simple cross channel microchip. For the pure advection regime of dispersion, we use numerical simulations of the transient convective diffusion processes associated with electrokinetics together with an optimization algorithm to design a voltage control scheme which produces an injection plug that has minimal advective dispersion. We also validate this optimal injection scheme using fluorescence visualizations. These validations show that optimized voltage scheme produces injections with a standard deviation less than one-fifth of the width of the microchannel.     

Determination of proanthocyanidins in fresh grapes and grape products using liquid chromatography with mass spectrometric detection

Fresh grapes and grape products, such as grape wine and grape juice, were analyzed for proanthocyanidins (PACs) using liquid chromatography with electrospray ionization mass spectrometric (MS) detection. PACs were successfully separated and analyzed on the basis of their protonated molecules, allowing the identification of PACs in different degrees of polymerization from monomers to oligomers (up to 7 units), and in various isomeric forms. Using reversed-phase high-performance liquid chromatography (HPLC) combined with MS detection, the PAC monomers, (+)-catechin (C), (-)-epicatechin (EC), (-)-catechin gallate (CG), and (-)-epicatechin gallate (ECG), were successfully quantified using selected ion monitoring (SIM) mode. Standard curves were fitted for each PAC ranging from 43.8 to 5600 ng/mL for C, from 42.2 to 5400 ng/mL for EC, from 36.7 to 4700 ng/mL for CG, and from 39.8 to 5100 ng/mL for ECG. Good linearity (r2>0.999) was achieved for each analyte. The accuracy and precision (RSD) were within 10% (n=8) at the limit of detection. This method allows direct quantification of monomeric PACs in fresh grapes and grape-derived products. Additionally, flow injection analysis (FIA) was applied to estimate the concentration levels of PAC oligomers by comparing their FIA-MS peak areas, which were well correlated (r2=0.936) to the total concentrations of PAC monomers.     

Study of the major fragmentation pathways of cypermethrin and related synthetic insecticides using tandem mass spectrometry

Fragmentation pathways of the synthetic pyrethroid cypermethrin and four structurally related insecticides were investigated using a tandem quadrupole mass spectrometer incorporating a hexapole collision cell under positive-ion electron impact ionization conditions. Conventional mass spectrometry using the first quadrupole analyser only and tandem mass spectrometry on selected precursor ions and product ions, and also constant neutral loss scan experiments, were used. Mechanisms and fragmentation pathways are proposed to explain the inherent stability of ions associated with the benzylphenoxy portion of this class of insecticide.     

Electron transfer dissociation in the hexapole collision cell of a hybrid quadrupole-hexapole Fourier transform ion cyclotron resonance mass spectrometer

Electron transfer dissociation (ETD) of proteins is demonstrated in a hybrid quadrupole-hexapole Fourier transform ion cyclotron resonance mass spectrometer (Qh-FTICRMS). Analyte ions are selected in the mass analyzing quadrupole, accumulated in the hexapole linear ion trap, reacted with fluoranthene reagent anions, and then analyzed via an FTICR mass analyzer. The hexapole trap allows for a broad fragment ion mass range and a high ion storage capacity. Using a 3 T FTICRMS, resolutions of 60 000 were achieved with mass accuracies averaging below 1.4 ppm. The high resolution, high mass accuracy ETD spectra provided by FTICR obviates the need for proton transfer reaction (PTR) charge state reduction of ETD product ions when analyzing proteins or large peptides. This is demonstrated with the ETD of ubiquitin and apomyoglobin yielding sequence coverages of 37 and 20%, respectively. We believe this represents the first reported successful combination of ETD and a FTICRMS.     

Development of an ion mobility spectrometer for use in an atmospheric pressure ionization ion mobility spectrometer/mass spectrometer instrument for fast screening analysis

An ion mobility spectrometer that can easily be installed as an intermediate component between a commercial triple-quadrupole mass spectrometer and its original atmospheric pressure ionization (API) sources was developed. The curtain gas from the mass spectrometer is also used as the ion mobility spectrometer drift gas. The design of the ion mobility spectrometer allows reasonably fast installation (about 1 h), and thus the ion mobility spectrometer can be considered as an accessory of the mass spectrometer. The ion mobility spectrometer module can also be used as an independently operated device when equipped with a Faraday cup detector. The drift tube of the ion mobility spectrometer module consists of inlet, desolvation, drift, and extraction regions. The desolvation, drift and extraction regions are separated by ion gates. The inlet region has the shape of a stainless steel cup equipped with a small orifice. Ion mobility spectrometer drift gas is introduced through a curtain gas line from an original flange of the mass spectrometer. After passing through the drift tube, the drift gas serves as a curtain gas for the ion-sampling orifice of the ion mobility spectrometer before entering the ion source. Counterflow of the drift gas improves evaporation of the solvent from the electrosprayed sample. Drift gas is pumped away from the ion source through the original exhaust orifice of the ion source. Initial characterization of the ion mobility spectrometer device includes determination of resolving power values for a selected set of test compounds, separation of a simple mixture, and comparison of the sensitivity of the electrospray ionization ion mobility spectrometry/mass spectrometry (ESI-IMS/MS) mode with that of the ESI-MS mode. A resolving power of 80 was measured for 2,6-di-tert-butylpyridine in a 333 V/cm drift field at room temperature and with a 0.2 ms ion gate opening time. The resolving power was shown to be dependent on drift gas flow rate for all studied ion gate opening times. Resolving power improved as the drift gas flow increased, e.g. at a 0.5 ms gate opening time, a resolving power of 31 was obtained with a 0.65 L/min flow rate and 47 with a 1.3 L/min flow rate for tetrabutylammonium iodide. The measured limits of detection with ESI-MS and with ESI-IMS/MS modes were similar, demonstrating that signal losses in the IMS device are minimal when it is operated in a continuous flow mode. Based on these preliminary results, the IMS/MS instrument is anticipated to have potential for fast screening analysis that can be applied, for example, in environmental and drug analysis.     

The automatic visualisation of carry-over in high-throughput flow injection analysis mass spectrometry

A high-throughput flow injection analysis mass spectrometry system (FIA-MS) was developed for the purity estimation of multiple parallel combinatorial chemistry synthetic samples, and has measured over 70 000 samples in two years. An in-house Visual Basic application called RackViewer allows a fast, direct, easy and economic inspection of the estimates at geographically dispersed laboratory workbenches via the corporate network. Due to the large numbers of samples involved, surreptitious inter-sample carry-over represents one threat to the accuracy of these purity estimates. It can become serious when reducing the measurement duty cycle in order to develop faster throughput rates. Over 400 samples drawn equally from five different combinatorial synthetic families were measured to explore this threat. By analogy with the colour rendering of the purity estimates, inter-sample carry-over was automatically calculated for each measurement, colour rendered and then depicted within RackViewer. Our FIA-MS in daily use has a median basal carry-over of 0.88%.