Hierarchical TiO2 Flower-spheres with Large Surface Area and High Scattering Ability: an Excellent Candidate for High Efficiency Dye Sensitized Solar Cells

Hierarchical TiO₂ flower-spheres assembled from porous nanosheets-stacked of nanoparticles were synthesized by a simple hydrothermal method with one-step. The as-prepared TiO₂ flower-spheres showed a diameter range from 200 nm to 550 nm and a large surface area of 188 m²/g. A double layer photoanode made of P25 nanoparticles and as-prepared TiO₂ flower-spheres was fabricated for the dye sensitized solar cells(DSSCs). The efficient light scattering and dye absorption of the photoanode can be attributed to the top-layer of hierarchical TiO₂ flower-spheres. DSSCs based on the double layers photoanode exhibit a higher energy conversion efficiency of 8.11% with a short-circuit photocurrent density of 17.87 mA/cm², indicating that there is an increase of 38% in the conversion efficiency compared to those based on electrode P25(5.91%, 14.09 mA/cm²).     

Regulating Phase Junction and Oxygen Vacancies of TiO2 Nanoarrays for Boosted Photoelectrochemical Water Oxidation

In this study, we have provided a facile solution to synthesize well-aligned titanium dioxide nanorods by using hydrothermal reaction. By calcining the materials under different atmospheres and temperatures, a batch of titanium dioxides with excellent oxygen evolution reaction(OER) catalytic efficiency were obtained. This new structured TiO₂ photoanode material yields a high photocurrent density of 5.69 mA/cm² at 1.23 V vs. reversible hydrogen electrode(RHE) under simulated solar light(100 mW/cm²). Surface photovoltage techniques and other measurements were carried out to confirm that the enhanced photoelectrochemical performances were attributed to the synergistic effect of the phase junction and a certain content of surface states, which accelerate the separation and transmission of the photogenerated charges. This material with phase junction and surface states promises a potential application in the field of photoelectric catalysis under solar light.     

Influence of pyrimidine additives in electrolytic solution on dye-sensitized solar cell performance

The influence of pyrimidine additives on the performance of a bis(tetrabutylammonium)cis-bis(thiocyanato)bis(2,2′-bipyridine-4-carboxylic acid, 4′-carboxylate)ruthenium(II) dye-sensitized TiO₂ solar cell with an I⁻/I₃⁻ redox electrolyte in acetonitrile was studied. The current–voltage characteristics were measured for more than 10 different pyrimidine derivatives under AM 1.5 (100 mW/cm²). The pyrimidine additives tested had varying effects on the performance of the cell. The additives drastically enhanced the open-circuit photovoltage (V_oc) and the solar energy conversion efficiency (η), but usually reduced the short circuit photocurrent density (J_sc) of the solar cell. Physical and chemical properties of the pyrimidines were computationally calculated in order to determine the reasons for the additive effects on cell performance. Consequently, the greater the calculated partial charge of the nitrogen atoms in the pyrimidine groups, the larger the V_oc but the smaller the J_sc values. The V_oc of the cell also increased as the ionization energy of the pyrimidine molecules decreased. Moreover, as the calculated dipole moment of the pyrimidine derivatives increased, the J_sc value was reduced, but the V_oc value was enhanced. These results suggest that the electron donicity of pyrimidine additives influenced the interaction with TiO₂ electrode and I⁻/I₃⁻ electrolyte, which lead to the changes in dye-sensitized solar cell performance.     

叶绿素、染料体系光电效应的研究

叶绿素光电性质的研究有特殊意义.70年代开始国内外已有很多报道, 它们有整流、光导、光伏和光解水制取氢和氧等性质^[1-5].我们也报道过叶绿素a/聚乙烯醇夹层电池的研究^[6-8]。     

Properties of chemical vapour deposited nanocrystalline TiO2 thin films and their use in dye-sensitized solar cells

Nanocrystalline titanium dioxide (TiO₂) thin films have been prepared using titanium(IV) isopropoxide as a precursor onto the glass and fluorine doped tin oxide coated glass substrates by chemical vapour deposition technique at 400 °C substrate temperature. X-ray diffraction study confirms the polycrystalline nature of TiO₂ with anatase phase having tetragonal crystal structure. The films are 975 nm thick and transparent having transmittance grater than 80%. Atomic force microscopy (AFM) images reveal the nanocrystalline morphology with grain size of 200 nm. The film shows a sharp absorption edge near 350 nm. Photoelectrochemical study shows that TiO₂ thin film sensitized with Brown Orange dye is found to exhibit relatively maximum I_sc and V_oc among the studied dyes. The values of fill factor (FF) and efficiency (η) for the dye-sensitized solar cell (Brown Orange dye-sensitized TiO₂) are 0.54 and 0.17%, respectively. Such films would serve as better prospects for dye-sensitized solar cells.     

Post-modification using aluminum isopropoxide after dye-sensitization for improved performance and stability of quasi-solid-state solar cells

In this study, dye-sensitized TiO₂ electrodes were immersed into a solution of aluminum isopropoxide and after hydrolysis quasi-solid-state solar cells were fabricated. The interaction between the dye and the resulting Al₂O₃ overlayer was investigated by ultraviolet–visible (UV–vis) spectrum, Fourier transform infrared (FTIR) spectrum and X-ray photoelectron spectrum (XPS). The current density–voltage (I–V) characteristics showed that the overlayer increased the photovoltage and decreased the photocurrent under low intensity irradiation, and increased both the photovoltage and photocurrent under AM 1.5 irradiation. The Al₂O₃ overlayer at the dye/electrolyte interface resulted in a 28% improvement in overall photo-to-electrical conversion efficiency from 2.60 to 3.32%. Dark current measurements showed that Al₂O₃ acted as an insulator barrier to retard recombination between the TiO₂ and dye/quasi-solid-state electrolyte interface. Without encapsulation, dye-sensitized solar cells with Al₂O₃ coating after sensitization also exhibited improved stability compared to cells without coating.     

苯基磷酸联吡啶钌络合物敏化纳晶多孔TiO2薄膜电极光电性能研究

用有机光敏染料敏化半导体,通过染料分子的吸附功能基团与半导体相互作用,使染料分子与半导体表面之间建立电性耦合,进行有效的电荷转移,可以形成有机-半导体复合新型光电功能材料。联吡啶钌络合物有较强的可见光吸收、氧化还原性能可逆、氧化态稳定性高,是一类性能优越的有机光敏染料。近来许多研究发现,羧酸联吡啶钌的强吸附与TiO₂纳晶薄膜的大比表面相结合,导致光生电荷快速注入TiO₂导带达到有效的电荷分离,得到了接近100%的单色光光电流效率^[1]。为研究联吡啶钌分子的不同吸附功能基团与TiO₂纳晶薄膜表面的相互作用对提高光电性能的影响,本文报道苯基磷酸取代的联吡啶钌络合物敏化纳晶多孔TiO₂薄膜的光电性能。     

NiO/TiO2异质结构纳米管阵列膜对不锈钢的光生阴极保护及其储能性能

本工作通过修饰TiO₂制备半导体复合膜,提高其光吸收和光电化学性能,以期应用于光生阴极保护。先采用阳极氧化法在Ti表面制备TiO₂纳米管阵列膜,再应用水热处理法在膜表面沉积NiO纳米颗粒,形成具有异质结构纳米管复合膜。利用扫描电子显微镜、X-射线衍射、X-射线光电子能谱、紫外-可见吸收光谱、光致发光谱和光电化学技术对制备的纳米膜进行表征。结果表明,与纯TiO₂纳米管膜比较,NiO/TiO₂纳米管复合膜的光吸收扩展到可见光区。白光照射下,其在0.5 mol·L^?1 KOH和1 mol·L^?1 CH3OH混合液中的光电流密度达到176μA·cm^?2,是纯TiO₂纳米管膜的2倍。复合膜具有良好的光生阴极保护作用,与0.5 mol·L^?1 NaCl溶液中的403不锈钢耦连后,可使其电极电位下降440 mV,在光照2.5 h再转为暗态后,因具有电荷储存能力还可继续提供约15.5 h的阴极保护效应。     

YSZ传导膜H_2S固体氧化物燃料电池

研究了Y2O3稳定的ZrO2(YSZ)氧离子传导膜H2S固体氧化物燃料电池性能。掺杂NiS、电解质、Ag粉和淀粉制备了双金属复合MoS2阳极催化剂,掺杂电解质、Ag粉和淀粉制备了复合NiO阴极催化剂,用扫描电镜对YSZ和膜电极组装(MEA)进行了表征,比较了不同电极催化剂的性能和极化过程,考察了不同温度对电池性能的影响。结果表明,双金属复合MoS2/NiS阳极催化剂在H2S环境下比Pt和单金属MoS2催化剂稳定,复合NiO阴极催化剂比Pt性能好,在电极催化剂中加入Ag可显著提高电极的导电性;与Pt电极相比,复合MoS2阳极和复合NiO阴极催化剂的过电位较小,阳极的极化比阴极侧小;温度升高,电池的电流密度与功率密度增加,电化学性能变好。在750℃、800℃、850℃和900℃及101.13 kPa时,结构为H2S、(复合MoS2阳极催化剂)/YSZ氧离子传导膜/(复合NiO阴极催化剂)、空气的燃料电池最大功率密度分别为30 mW/cm2、70 mW/cm2、155 mW/cm2及295 mW/cm2、最大电流密度分别为120 mA/cm2、240 mA/cm2、560 mA/cm2和890 mA/cm2。     

两亲性季铵盐对钙钛矿太阳能电池效率和稳定性的影响

将廉价易得的两亲性季铵盐十六烷基三甲基溴化铵（CTMAB）加入到钙钛矿前驱体溶液中，通过调节添加量研究了CTMAB对钙钛矿太阳能电池效率和稳定性的影响.结果表明，加入CTMAB后制备的钙钛矿薄膜更加致密均匀，表面缺陷更少，钙钛矿晶体结晶性得到显著提高，从而提高了电池的光电转换效率及电池稳定性；含有CTMAB的钙钛矿太阳能电池的光电转换效率（PCE）为18.03%，明显高于未添加CTMAB的电池效率（17.05%）；含有CTMAB的电池稳定性有较大的提高，在一定湿度环境中保存40 d后效率仍达初始效率的95%，而未添加CTMAB的器件效率只有初始效率的70%.     

Pd增强缺陷态TiO2纳米管阵列的光催化产氢性能

通过光还原沉积法, 利用氧空位诱导作用, 在Ni掺杂的缺陷态TiO₂纳米管阵列(TNT-Ni)上得到金属 Pd含量不同的Pd-TNT-Ni催化剂. 采用场发射扫描电子显微镜(SEM)、 X射线光电子能谱(XPS)、 紫外-可见 漫反射(UV-Vis DRS)、 表面光电压(SPV)、 光致发光光谱(PL)和电化学测试等表征手段, 探究了Pd与Ni掺杂的缺陷态TiO₂纳米管阵列之间的强相互作用对其光吸收特性和载流子分离及传输效率的影响, 阐明了强相互 作用对材料光催化活性的调控机理, 提出了Pd增强Pd-TNT-Ni光催化性能的作用机理. 结果表明, 通过光还 原法制备的Pd纳米颗粒尺寸为10~20 nm的Pd₁₂₀-TNT-Ni样品的光响应值为4.22 mA/cm², 是未负载Pd样品光 响应值(1.14 mA/cm²)的3.7倍, 其具有最佳的平均产氢速率(5.16 mmol·g^?1·h^?1), 是TNT样品平均产氢速率 (0.45 mmol·g^?1·h^?1)的12倍, 表明Pd与缺陷态TiO₂纳米管阵列之间的强相互作用驱动了载流子的分离及传输, 且Pd作为电子捕获势阱及反应活性位点, 显著提高了材料的光催化性能.     

Investigation of the photocatalytic degradation of organochlorine pesticides on a nano-TiO2 coated film

The photocatalytic degradation of organochlorine pesticides including -, β-, γ-, δ-hexachlorobenzene (BHC), dicofol and cypermethrin were carried out on a nano-TiO₂ coated films under UV irradiation in the air. The photocatalytic conditions, including the amount of TiO₂, irradiation time and the intensity of light were optimized. The pesticides were most effectively degraded under the condition of 2.24 mg/cm² on TiO₂ film and a 400 W UV irradiation of high-pressure mercury lamp with a wavelength of 365 nm. A typical organochlorine pesticide, 20 μg -BHC, was dipped onto the TiO₂ film surface and degraded completely within 20 min. In addition, the photocatalytic degradation pathways on the nano-TiO₂ coated film were discussed.     

Dye-sensitized solar cells made from BaTiO3-coated TiO2 nanoporous electrodes

We reported on the preparation of a thin BaTiO₃-coated layer (2.27 nm) on the surface of TiO₂ and its further application in the dye-sensitized solar cells (DSCs). The as-prepared BaTiO₃–TiO₂ films were characterized by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM) and transmission electron microscope (TEM). The performances of the DSCs with and without BaTiO₃ coating were analyzed by cyclic voltammograms (CVs), electrochemical impedance spectroscopy (EIS), and current–voltage measurements. It was found that the BaTiO₃–TiO₂ films with about 12 μm thickness increased the dye adsorption, resulting in increased J_sc. In the meantime, the BaTiO₃ modification on the TiO₂ surface is beneficial to the formation of an energy barrier against the electron transfer from TiO₂ to I₃⁻, providing the increase of V_oc due to the increased electron density in the TiO₂ that is caused by the increased electron lifetime.     

Au/PATP/PANI膜电极和Au/PATP/PANI/TiO2膜电极的光电化学

聚苯胺（PANI）是一种结构、 性质不同于聚乙炔和聚吡咯的新型导电高聚物,有着十分广泛的应用[1,2].近年来利用光电化学研究聚苯胺的电子结构、 掺杂情况引起人们的重视[3～5].在酸性溶液中电聚合制备聚苯胺的循环伏安曲线上出现两对氧化还原峰,其峰值电位分别为E11/2=0.13 V和E21/2=0.7 V(对饱和甘汞电极).通过改变电极电位,可获得部分氧化态、还原态、氧化态等3种状态的聚苯胺.部分氧化态具有金属导电性,还原态和氧化态均为绝缘体.本文测量3种状态聚苯胺膜电极的光电响应,首次得到其光电流谱,发现聚苯胺一些新的光电化学实验结果.提出了覆盖绝缘体的金属内发射的光电化学模型.同时,在聚苯胺膜上电沉积纳米TiO2微粒膜,得到广谱区的复合光电材料.     

Stabilization mechanism of TiO2 on flexible fluorocarbon films as a functional photocatalyst

The repetitive discoloration kinetics of the azo-dye Methyl Orange (taken as a model organic compound) was followed under solar simulated radiation (90 mW/cm²) to assess the performance of the TiO₂/Tedlar^® composite photocatalyst. The influence of solution parameters on the photo-discoloration process: pH, dye concentration, applied light intensity and concentration of H₂O₂ were systematically investigated. During the photocatalysis a modification occurs in the TiO₂/Tedlar^® composite due to the TiO₂ interaction with the Tedlar^® film. Physical insight is given for the stabilization mechanism of the TiO₂ particles in the Tedlar matrix based on the data obtained by X-ray photoelectron spectroscopy (XPS). The F 1s peak of the Tedlar film indicates that the TiO₂ is loaded on the Tedlar fluoro-groups. The loading of TiO₂ on the 75 μm thick Tedlar^® film was 0.9% (w/w) as determined by atomic absorption spectrophotometry (AAS). Attenuated total reflection infrared spectroscopy (ATRIR) shows no formation of additional bands within the photodiscoloration reaction. This shows that an efficient catalysis taking place on the TiO₂/Tedlar^® surface. The rugosity (mean square roughness, rms) of the TiO₂/Tedlar^® film was determined by atomic force microscopy (AFM) to be 19.7 nm. This value remained constant during long-term operation. Transmission electron microscopy (TEM) reports the thickness and coverage of TiO₂ Degussa P-25 on the Tedlar^® surface before and after photocatalysis.     

Mixed-phase Mesoporous TiO2 Film for High Efficiency Perovskite Solar Cells

Mesoporous scaffold structures have played great roles in halide perovskite solar cells(PSCs),due to the excellent photovoltaic performance and commercial perspective of mesoporous PSCs.Here,we reported a mixed-phase TiO2 mesoporous film as an efficient electron transport layer(ETL)for mesoporous perovskite solar cells.Due to the improved crystal phase,fihn thickness and nanopartMe size of TiO2 layer,which were controlled by varying the one-step hydrothermal reaction time and annealing time,the PSCs exhibited an outstanding short circuit photocurrent density of 25.27 mA/cm^2,and a maximum power conversion efficiency(PCE)of 19.87%.It is found that the ultra-high Jsc attributes to the excellent film quality,light capturing and excellent electron transport ability of mixed-phase TiO2 mesoporous film.The results indicate that mix-phase mesoporous metal oxide fihns could be a promising candidate for producing effective ETLs and high efficiency PSCs.     

D-π-A-π-A结构有机光敏染料的合成及其在太阳能光电转化和光解水制氢中的应用

选择N,N'-二甲基苯胺作为电子给体,乙炔基和苯基作为π桥键,苯并噻二唑基团作为辅助受体,氰基丙烯酸为电子受体设计合成了一个具有D-π-A-π-A结构的有机染料OD2。对该染料的光谱性能和电化学性能进行了研究,并将其用作光敏剂引入太阳能光电转化和光解水制氢领域。当OD2应用于光伏领域：在AM1.5（100 mW·cm^-2）的光强下,OD2敏化的电池的光电转化效率（η）为4.40%（短路电流密度（J_sc）=10.58 mA·cm^-2,开路电压（V_oc）=630 mV,填充因子（FF）=0.65）;当OD2应用于染料敏化可见光催化制氢领域：在300 W氙灯光源可见光照射10 h,OD2敏化的Pt/TiO₂在pH=7.0,10%（φ,体积分数）三乙醇胺水溶液中的催化转化数（TON）为140,相应的表观制氢量子产率（Φ_H2）仅为0.42%。显然,OD2在光电转化领域比可见光催化分解水制氢领域更具有应用潜力。     

Asymmetric supercapacitors based on high capacitance Ni6MnO8 and graphene

A fast, facile and cost-effective method is used to synthesize Ni₆MnO₈ electrode with high electrochemical performance. The supercapacitor based on Ni₆MnO₈ electrode exhibits excellent stability, high area specific capacitance and promising energy and power density.     

铂微粒修饰的氧化钛电极对甲醇的电催化氧化性能

直接甲醇质子交换膜燃料电池(DMPEMFC)可用作未来电动车辆的动力电源,但要达到实际应用还有大量问题有待进一步解决.目前限制DMPEMFC实际应用的主要问题是甲醇阳极氧化催化剂低的活性、高的价格及催化剂的毒化.     

Preparation and photoelectrochemical characterization of nano-particulate TiO2 and polyaniline composite films on Au

TiO₂ and polyaniline(PANI) composite film was obtained by electrochemical methods^[1] and investigated for solar energy conversion application. A strong rectifying effect was found in the cyclic voltammogram of the film in dark when the scan speed was slow enough (5 mV/s) and a quasi-reversible voltammogram of the film was observed when the scan speed was fast (100 mV/s). The results of both the cyclic voltammograms and the SEM images of the composite film show that the PANI film is almost completely covered with nano-particulate TiO₂. Two anodic photocurrent bands and a cathodic band was observed in the spectra of the photocurrent of the TiO₂/PANI/PATP(p-aminothiophenol)/Au film in 0.05 mol/L Fe(CN)₆^3-/Fe(CN)₆^4- solution. The band at 300~400 nm (3.1~4.1 eV) can be ascribed to the photocurrent band of TiO₂ particles and the bands at 450~730 nm (1.7~2.8 eV) can be ascribed to those of the PANI. The partially-oxidized PANI has internal photoemission function and the insulating matrix of PANI is verified to be reduced PANI with a 3.33 eV bandgap energy. The flat-band potentials of partially-oxidized PANI and TiO₂/PANI composite film in 1.0 mol/LHClO₄ solution are determined as 0.87 V and 0.09(SHE) from Mott-Schottky plots, respectively.