平均键能方法在应变层异质结带阶研究中的应用

将平均键能方法推广应用于应变层异质结的带阶研究.通过流体静压力应变和单轴应变对带阶参量E_mv作用的仔细研究,发现平均带阶参量E_mv,av=E_m-E_v,av在不同应变状态下基本上保持不变.因此,在应变层带阶参量E_mv的计算中,只需计算其发生应变前体材料的带阶参量E_mv,o值并引用形变势b和SO裂距Δ₀的实验值,通过简便的代数运算得到应变层的E_{mv 关键词： 异质结 平均键能方法 价带偏移}     

利用同步辐射光电子能谱技术测量ZnO/PbTe异质结的能带带阶

异质结结构界面的能带带阶是一个非常重要的参数,该参数的精确确定直接影响异质结的光电性质研究以及异质结在光电器件上的应用.利用同步辐射光电子能谱技术测量了ZnO/PbTe异质结结构的能带带阶.测量得到该异质结价带带阶为2.56 eV,导带带阶为0.49 eV,是一个典型的类型I的能带排列.利用变厚度扫描的测量方法发现,ZnO/PbTe界面存在两种键,分别是Pb—O键(低结合能)和Pb—Te键(高结合能).在ZnO/PbTe异质结界面的能带排列中导带带阶较小,而价带带阶较大,这一能带结构有利于PbTe中的激发电子输运到ZnO导电层中.该类结构在新型太阳电池、中红外探测器、激光器等器件中具有潜在的应用价值.     

Si／Ge应变层异质结带的价带偏移理论计算

在应变异质结价带偏移从头算赝势法的理论计算中，建议一种以平均键能为参考能级的△Ｅｖ值理论计算方法，该方法在Ｓｉ为衬底，以Ｇｅ为衬底和自由共度生长等３种不同应变情况的Ｓｉ／Ｇｅ异质结价带偏移△Ｅｖ值计算中，分别得到０．７３１ｅＶ，０．２４３ｅＶ和０．５２１ｅＶ的计算结果。     

经验赝势法在GaAs/Ge,AlAs/GaAs和AlAs/Ge异质结能带排列理论计算中的应用

在异质结能带排列的理论计算中，采用经验赝势能带计算方法，并将平均键能Ｅ_m作为参考能级，计算了GaAs/Ge,AlAs/GaAs和AlAs/Ge三种异质结的整体能带结构和排序（包括价带、导带和带隙），获得完整且较准确的理论计算结果，其价带偏移ΔＥ_ｖ的计算值分别为０.５７，０.５０和１.０７ｅＶ．     

六角氮化硼(h-BN)对单层硒化铟(InSe)的调制效应及这一新结构的电子性质

采用基于密度泛函理论的第一性原理计算和分析了三种InSe/h-BN异质结的结构和电子性质.研究发现InSe/h-BN异质结具有间接带隙特点,并且价带顶和导带底的贡献均来自于InSe,差分电荷密度表明体系中没有明显的电荷交换.通过体系能带结构,我们发现h-BN层对单层InSe有着明显的调控效应.对比纯粹应变调控下单层的InSe的能带结构,发现h-BN对InSe能带结构的调控效应实际上是由InSe和h-BN之间的相互作用而诱导的晶格应变引起的.我们的研究结果表明,单层InSe沉积或生长在不同h-BN片上可以获得不同的晶格应变,实现对单层InSe能带结构的有效调控.     

As/HfS2范德瓦耳斯异质结电子光学特性及量子调控效应

两种或两种以上的单层材料堆垛成范德瓦耳斯异质结是实现理想电子及光电子器件的有效策略.本文选用As单层及HfS₂单层,采用6种堆垛方式构建As/HfS₂异质结,并选取最稳结构,利用杂化泛函HSE06系统地研究了其电子和光学性质以及量子调控效应.计算发现,As/HfS₂本征异质结为Ⅱ型能带对齐半导体,且相对两单层带隙(>2.0 eV)能明显减小(约0.84 eV),特别是价带偏移(VBO)和导带偏移(CBO)可分别高达1.48 eV和1.31 eV,非常有利于研发高性能光电器件和太阳能电池.垂直应变能有效调节异质结的能带结构,拉伸时带隙增大,并出现间接带隙到直接带隙的转变现象,而压缩时,带隙迅速减少直到金属相发生.外加电场可以灵活地调控异质结的带隙及能带对齐方式,使异质结实现Ⅰ型、Ⅱ型和Ⅲ型之间的转变.此外,As/HfS₂异质结在可见光区域有较强的光吸收能力,且可通过外加电场和垂直应变获得进一步提高.这些结果表明As/HfS₂异质结构在电子器件、光电子器件和光伏电池领域具有潜...     

重掺B对应变SiGe材料能带结构的影响

硅锗异质结双极晶体管(SiGe HBT)一般以重掺硼(B)的应变SiGe层作为基区.精确表征SiGe材料能带结构对SiGe HBT的设计具有重要的意义.在应变SiGe材料中，B的重掺杂一方面会因为重掺杂效应使带隙收缩，另一方面，B的引入还会部分补偿Ge引起的应变，从而改变应变引起的带隙变化.在重掺B的应变SiGe能带结构研究中，采用半经验方法，考虑了B的应变补偿作用对能带的影响，对Jain-Roulston模型进行修正，并分析了重掺杂引起的带隙收缩在导带和价带的分布.     

应变层超晶格InAs/InP界面的平均键能行为与价带边不连续性

采用LMTO能带方法,对两种不同应变状态下(自由形变和以InP为衬底),应变层超晶格(InAs)₁(InP)₁(001)和与应变层超晶格的分子层相对应的应变体材料,以及无应变的体材料进行了第一原理计算,并采用冻结势方法求出了两种超晶格各分子层的平均键能。结果表明,能存在应变的情况下,异质界面两边的平均键能非常一致,且这种一致性受应变状态的影响很小,因而可以把它用来作为确定应变层超晶格价带边不连续值(△E_v)的普遍适用的参考能级。研究了应变对 关键词：     

生长在Si(OO1)衬底上的超晶格(Si_2)_4/(GaAs)_4的电子能带结构及光学性质

按照Peressi等的第一性原理赝势计算得到的原子几何构形及能带边不连续值,采用紧束缚方法计算了生长在Si(001)衬底上的超晶格(Si_2)_4/(GaAs)_4的电子能带结构及光跃迁振子强度.相应于两种不同的原子几何构形:X端界面及Y端界面情况,超晶格具有不同的基本带隙.但是不管哪种情况,它们都存在能量近乎简并的两类导带底能谷——Γ能谷及△能谷,它们的价带顶都处在Γ点.X端界面超晶格的价带顶附近的状态主要由GaAs层的价态波函数组成.对于Y端界面超晶格的价带顶附近的状态,Si层和GaAs层的价态波函数     

应变层异质结ZnS/ZnSe、ZnS/ZnSxSe1-x和ZnSe/ZnSxSe1-x价带带阶的研究

采用基于原子球近似下线性Mufin-Tin轨道(LMTO-ASA)的平均键能计算方法,研究了以ZnS_xSe_1-x为衬底,沿(001)方向外延生长的应变层异质结ZnS/ZnSe、ZnS/ZnS_xSe_1-x和ZnSe/ZnS_xSe_1-x的价带带阶值ΔE_v(x).研究表明,ΔE_v(x)值随衬底合金组分x单调变化。且两者的关系是非线性的。在此计算结果与其它理论计算和实验结果符合较好。     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.     

A stereo matching algorithm using multi-peak candidate matches and geometric constraints

Gray cross correlation matching technique is adopted to extract candidate matches with gray cross correla- tion coefficients less than some certain range of maximal correlation coefficient called multi-peak candidate matches. Multi-peak candidates are extracted corresponding to three closest feature points at first. The corresponding multi-peak candidate matches are used to construct the model polygon. Correspondence is determined based on the local geometric relations between the three feature points and the multi-peak candidates. The disparity test and the global consistency checkout are applied to eliminate the remaining ambiguous matches that are not removed by the local geometric relational test. Experimental results show that the proposed algorithm is feasible and accurate.