Acceleration test of substrate-packaged fiber Bragg grating sensor北大核心CSCD

To test whether the fiber Bragg grating (FBG) sensor can endure the steady-state inertial loads caused by the acceleration and the sensing properties during the loads, a FBG strain and temperature sensor with aluminium alloy substrate package was designed, and the acceleration performance on the sensor was tested. The sizes of FBG strain and temperature sensor were designed and its package process was described. The strain and temperature sensing mechanisms of FBG sensor were analyzed, and the spectrum detection and demodulation system based on volume phase grating and linear array photodetector was developed. Finally, the acceleration test equipment was established, and the acceleration performance test of the selected FBG strain and temperature sensor was carried out in accordance with the requirements and methods of GJB150.15A acceleration test. The experimental results show that in the 2 min performance test before and after the acceleration test, the wavelength offset is below to ±50 pm, and the change of light intensity is below to 0.3 V. In acceleration test, the maximum fluctuation of wavelength offset is ±7 pm, and the light intensity is in the range of 1.3 V~4.003 V. It is proved that the designed FBG sensor has the ability to endure the acceleration loads and has the good sensing performance during the acceleration loads. Copyright ©2022 Journal of Applied Optics. All rights reserved.     

动态匹配光栅解调传感系统温度补偿研究

采用一对辅助匹配光纤光栅,结合基于MAX1968EUI芯片闭环自动控制,设计了一种半导体小型温度控制系统.通过控制传感光栅反射峰值变化,使匹配光栅温度变化与传感光栅周围环境温度变化相匹配,实现了动态匹配光栅解调方案的应变测量系统温度补偿,消除了光纤光栅传感器温度、应变交叉敏感效应对传感系统测量应变的影响.解调系统同时采用一支微测力传感器作为解调系统的输出,消除了传统动态匹配光栅解调系统中压电陶瓷磁滞效应对测量结果的影响.实验结果表明,温度变化对系统应变测量影响误差小于2％,传感系统的线性优于0.999 5.     

Fiber grating sensors for high-temperature measurement

Two fiber grating sensors for high-temperature measurements are proposed and experimentally demonstrated. The interrogation technologies of the sensor systems are all simple, low cost but effective. In the first sensor system, the sensor head is comprised of one fiber Bragg grating (FBG) and two metal rods. The lengths of the rods are different from each other. The coefficients of thermal expansion of the rods are also different from each other. The FBG will be strained by the sensor head when the temperature to be measured changes. The temperature is measured based on the wavelength-shifts of the FBG induced by the strain. In the second sensor system, a long-period fiber grating (LPG) is used as the high-temperature sensor head. The LPG is very-high-temperature stable CO₂-laser-induced grating and has a linear function of wavelength–temperature in the range of 0–800 °C. A dynamic range of 0–800 °C and a resolution of 1 °C have been obtained by either the first or the second sensor system. The experimental results agree with theoretical analyses.     

A novel fiber Bragg grating high-temperature sensor

A novel fiber Bragg grating (FBG) sensor for the measurement of high temperature is proposed and experimentally demonstrated. The interrogation system of the sensor system is simple, low cost but effective. The sensor head is comprised of one FBG and two metal rods. The lengths of the rods are different from each other. The coefficients of thermal expansion of the rods are also different from each other. The FBG will be strained by the sensor head when the temperature to be measured changes. The temperature is measured basis of the wavelength shifts of the FBG induced by strain. A dynamic range of 0–800 °C and a resolution of 1 °C have been obtained by the sensor system. The experiment results agree with theoretical analyses.     

一种新型温度自适应光纤光栅动态传感系统

 研究了采用温度控制光纤Bragg光栅（FBG）作为信号解调器件的自适应光纤光栅动态传感系统。系统利用半导体制冷器件对滤波用FBG进行温度控制,以改变FBG的窄带滤波波长,使之在合适的滤波波长工作,以适应测量环境温度变化,实现对传感器环境温度变化的自适应。通过采用参考信道,去除系统噪音,提高测量精度。系统动态应变传感精度达到9.745×10^-10(Hz^-1/2。     

光纤光栅多参数桥梁结构监测系统的研究

从土木工程应用的实际情况出发,利用光纤光栅传感器具有波长绝对编码和易于复用的特点,提出工程化同时测量温度、应变和压力的全光栅型低成本分布式传感方案。设计了基于连续波调频技术的光纤光栅多参量桥梁结构监测系统,将光频域反射复用与波分复用技术相结合,实现分布式光栅传感网络的寻址,提高了系统复用容量。实验表明：所设计的传感系统能够准确监测结构重要部位的内部应变及车流量等参数,为桥梁结构的静、动载测试提供了准确的数据,同时也为桥梁的工作状态评估和健康诊断提供了依据。     

Dynamic strain measurement using two wavelength-matched fiber Bragg grating sensors interrogated by a cascaded long-period fiber grating

In this work, we describe a fiber Bragg grating (FBG) sensing system using two wavelength-matched FBG sensors for static and dynamic strain measurement. A cascaded long-period fiber grating (CLPG)-based demodulation technique has been used to interrogate the two wavelength-matched FBG sensors. Experimental results of static strain measurement show that the proposed system has a strain resolution of 1 με. This system has also been used for dynamic strain measurement. An eddy current displacement meter-based system has been used as a comparison measurement. Experimental results of dynamic strain measurement have proved that the FBG sensing system has a good performance in the measurement of dynamic strain. The results of static and dynamic strain measurement indicate that the sensing system using two wavelength-matched FBG sensors is superior to the single FBG sensor system.     

利用双周期光纤光栅实现应变和温度同时测量

提出了一种新颖双周期光纤光栅传感器。在同一段氢载光纤上先后写入长周期光纤光栅、短周期布拉格光纤光栅 ,利用长周期光栅和布拉格光栅对应变和温度敏感性的差异 ,可实现应变和温度的同时测量。实验中采用这种灵敏结构的双周期光栅 ,在 0～ 170 0 με和 2 0℃～ 12 0℃范围内 ,测量精度可达到± 16 με和± 0 8℃。     

基于滤波法的光纤光栅传感解调方案

FBG传感器对应变和温度的敏感体现在其反射光中心波长的变化上，因此如何测量波长的变化就成为FBG传感器的关键。在光纤光栅的多种解调方法中，因滤波法的测量器件制作简单，测量系统简易、方便直观而被广泛应用。主要介绍了8种基于滤波法的解调方法，对它们各自的成本、检测精度、测量范围、器件制作以及适用的环境进行了详细的比较，分析了它们的优缺点，以便于在不同的检测条件下选用最佳的解调方案。重点介绍了光学小波滤波解调法，探讨了其测量系统的原理，并指出该方法可用于微弱信号的检测与处理。     

铝槽封装光纤光栅传感器的增敏特性研究

提出了一种光纤布喇格光栅的铝槽封装工艺,并对铝槽封装光纤光栅传感器的应变与温度传感特性进行了实验研究和理论分析.与裸光纤光栅的测试结果比较表明,铝槽封装工艺基本不改变光纤光栅应变传感的灵敏性,但是温度灵敏度系数提高了3.5倍.经过该工艺封装的光纤光栅可以探测识别0.2 με的应变与0.02℃的温度变化.     

一种测量温度和流速的光纤光栅传感器

提出一种基于铝片的测量温度和流速的光纤布喇格光栅(FBG)传感器。采用一种耐高温胶将光纤布喇格光栅封装在一小铝片上，经过高温固化处理，可保持光纤光栅传感器的稳定性。通过-20℃～100℃温度实验，得到该传感器的温度灵敏度系数为0.0392nm/℃,是封装前的3.5倍，且传感器温度响应保持了很好的线性和重复性。从水温14.5℃时的流速实验中得到水流速在0～20m/s范围变化时，FBG峰值波长漂移了0.13nm,验证了此光纤光栅传感器测量流速的可行性。试验结果表明，该传感器既可以作为温度传感器，又可以作为流量传感器，并且制作简单，成本较低。     

长周期光纤光栅温度和应力传感特性研究

本文报道了长周期光纤光栅(LPG)温度和应力传感特性的实验研究结果,测得LPG的温度和应力灵敏系数均高于光纤布喇格光栅(FBG)灵敏系数的典型值,在11～80℃和0～100gf的温度和应力测量范围内,温度和应力响应曲线具有较好的线性.基于同一LPG不同透射波长具有不同温度和应力灵敏度的特性,实现了温度和应力的单光栅同时测量.     

A cheap and practical FBG temperature sensor utilizing a long-period grating in a photonic crystal fiber

A whole temperature sensor in one package utilizing a fiber Bragg grating (FBG) made in a conventional single-mode fiber and which uses a long-period grating (LPG) made in a photonic crystal fiber is proposed and experimentally demonstrated. The function of the interrogation is that the wavelength change of the FBG with environmental temperature is transferred to the intensity of the output via the LPG. Utilizing the temperature-insensitivity of the LPG in the PCF, the interrogation is stable and enables a cheap and practical temperature measurement system with a wide dynamic range.     

调频连续波分布式光纤布拉格光栅复用系统

研究了利用调频连续波(FMCW)技术对分布式光纤布拉格光栅(FBG)复用系统进行寻址的基本原理;仿真分析了FBG传感器复用距离是系统最小分辨距离的整数倍或非整数倍时,对频谱信号的影响;搭建了基于FMCW的FBG复用系统实验平台,当传感距离1000m时,分别验证了不同扫描周期与复用系统差频信号的线性关系,及不同扫频范围与系统差频信号的线性关系。实验结果表明:FBG复用距离是系统最小分辨距离整数倍时,在测量距离1100 m范围内,系统测量最大误差为243 Hz,最大相对误差小于5%,可以实现FBG传感器的地址查询功能。     

A lasing wavelength stabilized simultaneous multipoint acoustic sensing system using pressure-coupled fiber Bragg gratings

A fiber Bragg grating (FBG) sensor head, using a pressure coupling mechanism, was designed for broadband frequency response and structural strain-free characteristic. The pressure-coupled sensor heads were connected to a simultaneous multipoint acoustic sensing system based on a tunable laser. An intelligent lasing wavelength stabilization algorithm capable of identifying the direction of spectrum movement, the wavelength shifting speed, and a fiber bending event was developed so that the simultaneous multipoint acoustic sensing system could be used in environments with rapid temperature variations. The lasing wavelength feedback control algorithm updated the lasing wavelength into the steep slope of the FBG spectrum even under conditions of rapid temperature change. The averaging lasing wavelength updating time was only 21 s because the system can decide a minimal size in scan window by finding the FBG spectrum shifting speed and direction in real time. The system was able to update the lasing wavelength which missed the steep slope of the FBG spectrum under maximum temperature variation rates 0.3014 and −0.3246 °C/s. The proposed system detected simultaneous impact waves at multiple points under conditions of rapid temperature change and change in dynamic strain.     

Application of high-precision temperature-controlled FBG filter and light source self-calibration technique in the BOTDR sensor system

A high-precision temperature-controlled narrow band-stop fiber Bragg grating(FBG) filter and light source self-calibration technique are proposed for application in the Brillouin optical time domain reflectometer (BOTDR) sensor system.With the proposed application,the BOTDR sensor system maintains good long-term stability and temperature precision through the reduction of the center wavelength drift in the FBG filters and corresponding decrease in the changes in light intensity.The experiment result shows that temperature precision of 1℃and temperature stability of 0.7℃can be achieved in a temperature sensor over a range of 8 km.     

基于匹配光纤光栅法布里-珀罗干涉仪的应变解调方法

提出并实验验证了一种基于匹配光纤光栅法布里-珀罗干涉仪的应变传感器解调方法,该方法综合了光纤法布里-珀罗干涉技术和匹配光纤光栅滤波法的优点.通过半导体制冷片和压电陶瓷组成的闭环负反馈控制系统,精确调节匹配光栅法布里-珀罗干涉仪的温度和应变,有效解决了光栅法布里-珀罗干涉仪的失配问题,从而保证系统静态工作点处于最佳匹配位置,同时能够避免探头因环境温度波动导致的测量误差.实验结果表明,该系统能够响应50～800Hz的输入信号,应变最小分辨力至少为0.4nε/Hz1/2,解调灵敏度高,且不受环境温度波动的影响,因而在动态应变或振动测量中具有较高的实用性.     

基于封装光纤Bragg光栅传感器的混凝土应变监测试验研究

研究了光纤Bragg光栅封装工艺,提出并实现了两种封装光纤Bragg光栅传感器:工字型钢管封装光纤Bragg光栅应变传感器及钢管封装光纤Bragg温度传感器。研究了传感器的埋设工艺,采用金属丝固定法、钢管抽出法两种方法进行了埋设。将它们埋入到钢筋混凝土梁中,实现对混凝土的拉、压应变及温度的测量。结果显示,在试验梁弹性阶段,可以较为准确的监测混凝土应变。     

Temperature-insensitive fiber Bragg grating dynamic pressure sensing system

Temperature-insensitive dynamic pressure measurement using a single fiber Bragg grating (FBG) based on reflection spectrum bandwidth modulation and optical power detection is proposed. A specifically designed double-hole cantilever beam is used to provide a pressure-induced axial strain gradient along the sensing FBG and is also used to modulate the reflection bandwidth of the grating. The bandwidth modulation is immune to spatially uniform temperature effects, and the pressure can be unambiguously determined by measuring the reflected optical power, avoiding the complex wavelength interrogation system. The system acquisition time is up to 85 Hz for dynamic pressure measurement, and the thermal fluctuation is kept less than 1.2% full-scale for a temperature range of -10 degrees C to 80 degrees C.     

基于副载波调频技术的光纤光栅传感网络查询

分析了副载波调频技术用于光纤光栅阵列查询的基本原理。从理论上推算了系统的查询空间分辨率及查询范围,并结合波分复用技术进行了光纤光栅传感网络的地址查询演示实验,同时使用可调谐滤波器对每个光栅信号进行了解调。实验结果很好地说明了该查询方案的可行性,且在单个光栅上的被测应变与可调谐滤波器的控制电压呈较好的线性关系。该系统具备有查询由几百个FBG组成的传感网络的潜在能力。