Dynamic Tensile Testing of Soft Materials

Determination of dynamic tensile response of soft materials has been a challenge because of experimental difficulties. Split Hopkinson tension bar (SHTB) is a commonly used device for the characterization of high-rate tensile behavior of engineering materials. However, when the specimen is soft, it is challenging to design the necessary grips, to measure the weak transmitted signals, and for the specimen to achieve dynamic stress equilibrium. In this work, we modified the SHTB on the loading pulse, the equilibrium-monitoring system, and the specimen geometry. The results obtained using this modified device to characterize a soft rubber indicate that the specimen deforms under dynamic stress equilibrium at a nearly constant strain rate. Axial and radial inertia effects commonly encountered in dynamic characterization of soft materials are also minimized.     

An experimental study of inhomogeneous cyclic plastic deformation of 1045 steel under multiaxial cyclic loading

An experimental study was conducted on the inhomogeneous cyclic plastic deformation of 1045 steel under multiaxial cyclic loading. Thin-walled tubular specimens were used and small strain gages were bonded on the specimen surface to characterize the local deformation. The controlled loading paths included cyclic tension–compression, cyclic torsion, proportional axial-torsion, 90°-out-of-phase axial-torsion, and fully reversed torsion with a constant axial stress. The maximum stress in each experiment was lower than the lower yield stress of the material. It was found that the cyclic plastic deformation within the gage section of the specimen under multiaxial stress state followed the three-stage process that was observed from uniaxial loading, namely, incubation, propagation, and saturation. The plastic deformation was significantly inhomogeneous during the propagation stage, and the inhomogeneity continued through the saturation stage. The duration of each stage and the saturated strains were dependent on the cyclic stress amplitude and the loading path. Multiaxial stress state reduced the incubation stage. With identical equivalent stress magnitude, the nonproportional loading path resulted in the shortest incubation and propagation stages, and the saturated equivalent plastic strain magnitude was the smallest. Although the deformation over the gage section was inhomogeneous, the plastic deformation in a given local area was found to be practically isotropic.     

单搭接胶接接头拉伸剪切性能的数值模拟与实验研究

采用数值模拟和光测技术对单向拉伸载荷作用下单搭接胶接接头中的剪切性能进行分析,研究了不同厚度胶层中切应力的变化规律。用有限元方法(FEM)对不同胶层厚度的试件进行建模,得到了拉伸载荷下胶粘剂中的切应力分布及其统计参数。利用数字图像相关(digitalimage correlation,DIC)方法对试件的变形场进行测量。结果表明,当胶粘剂的厚度较小时,胶粘剂中的切应力的分布统计参数随着其厚度的增加会有显著的变化,但是当厚度超过一定的数值时,统计参数对厚度的变化不再敏感。     

Local Interface Shear Fracture of Bonded Steel Joints with Various Bondline Thicknesses

Interfacial fracture is a critical issue for extensive applications of adhesively bonded structures to a variety of modern industries. Extensive global experimental tests have been conducted to measure the global behavior of adhesively bonded joint, such as ultimate load capacity and toughness. Recently, several studies have also been employed to characterize the local interfacial traction–separation laws. However, very few tests have investigated the dependency of the local interfacial constitutive laws on the adhesive thickness, particularly, under Mode-II loading conditions. In this work, six typical adhesive thicknesses (from 0.1 mm to 1.0 mm) are prepared for the bonded joints with a configuration of end notched flexure (ENF) specimen to realize the Mode-II fracture loading (shear fracture). With a recently developed analytical model, the global energy release rates of the ENF specimens are experimentally measured. Meanwhile, with the image analysis technique, the local slips between the two adherends are obtained. Finally, based on the J-integral theory, the local interfacial constitutive laws at different bondline thicknesses are obtained. Several experimental findings are reported in this work. This work may provide valuable baseline experimental data for the input in cohesive zone model (CZM) based analytical and numerical simulations.     

Dynamic Experiments using Simultaneous Compression and Shear Loading

Material characterization at high strain rates under simultaneous compression and shear loading has been a challenge due to the differing normal and shear wave speeds. An experimental technique utilizing the compression Kolsky bar apparatus was developed to apply dynamic compression and shear loading on a specimen nearly simultaneously. Synchronization between the compression and shear loading was realized by generating the torsion wave near the specimen which minimizes the time difference between the arrival of the compression and torsion waves. This modified Kolsky bar makes it possible to characterize the dynamic response of a material to combined compression and shear impact loading. This method can also be applied to study dynamic friction behavior across an interface under controlled loading conditions. The feasibility of this method is demonstrated in the dynamic characterization of a simulant polymer bonded explosive material.     

拉扭复合加载下循环应力应变关系的研究

以拉扭簿壁管试件为研究对象,根据多轴临界面上的应力应变特性及多轴疲劳临界面法的结果,结合单轴循环应力应变关系,研究了多轴比例与非比例加载下的循环应力应变关系,推导出多应力应变关系模型,经拉扭复合比例与非比例物载试验难证,其预测结果与实测值相符合。     

Multiaxial cyclic deformation and non-proportional hardening employing discriminating load paths

Some novel discriminating multiaxial cyclic strain paths with incremental and random sequences were used to investigate cyclic deformation behavior of materials with low and high sensitivity to non-proportional loadings. Tubular specimens made of 1050 QT steel with no non-proportional hardening and 304L stainless steel with significant non-proportional hardening were used. 1050 QT steel was found to exhibit very similar behavior under various multiaxial loading paths, whereas significant effects of loading sequence were observed for 304L stainless steel. In-phase cycles with a random sequence of axial-torsion cycles on an equivalent strain circle were found to cause cyclic hardening levels similar to 90° out-of-phase loading of 304L stainless steel. In contrast, straining with a small increment of axial-torsion on an equivalent strain circle results in higher stress than for in-phase loading of 304L stainless steel, but the level of hardening is lower than for 90° out-of-phase loading. Tanaka’s non-proportionality parameter coupled with a Armstrong–Fredrick incremental plasticity model, and Kanazawa et al.’s empirical formulation as a representative of such empirical models were used to predict the stabilized stress response of the two materials under variable amplitude axial-torsion strain paths. Consistent results between experimental observations and predictions were obtained by employing the Tanaka’s non-proportionality parameter. In contrast, the empirical model resulted in significant over-prediction of stresses for 304L stainless steel.     

Process zone in the Single Cantilever Beam under transverse loading - Part II: Experimental

This paper describes an experimental arrangement to evaluate stress/strain fields in the process zone of asymmetric adhesively bonded joints. A transparent polycarbonate flexible beam was bonded to an aluminium alloy rigid block with an epoxy adhesive in a Single Cantilever Beam (SCB) configuration. The flexible adherend was loaded in the direction parallel to the initial crack front at constant rate. To monitor strains induced by bending and shear along the beam, electric strain gauges were attached to the upper surface of the flexible adherend. Thus strain distribution was measured above the bonded surface, which could be used to monitor crack propagation and investigate stress redistribution in the process zone. A Timoshenko beam lying on a Pasternak elastic foundation model was used for the analysis of experimental findings. Subsequently, the Digital Image Correlation technique was used to measure the flexible substrate in-plane displacement field in the vicinity of the crack front and to assess the specimen kinematics. We found that strain gauge instrumentation of the fracture mechanics specimen was a very sensitive technique for experimental analysis of crack propagation under complex loading, offering fine investigation of stress distribution in the cohesive zone.     

Creep constitutive modeling of an aluminum alloy under multiaxial and cyclic loading

A constitutive model is developed to characterize creep response of polycrystalline metals. The model is based on the effective stress concept and back stress is utilized as an internal variable. A memory aspect is incorporated in the model to account for the previous maximal stress as a result of dislocation related micromechanisms. The model is used to predict the creep potential of an aluminum alloy under multiaxial and cyclic loading. The predicted results are compared with the available experimental results on an aluminum alloy (2618-T61). The associated six basic model parameters are evaluated by using an optimization technique, called ‘Box Algorithm’. These model parameters are then used to predict some unoptimized experimental data sets. The influence of multiaxial and cyclic loadings is investigated in detail for the selected aluminum alloy. Overall, excellent correlations are observed.     

Multiaxial and non-proportional loading responses,anisotropy and modeling of Ti–6Al–4V titanium alloy over wide ranges of strain rates and temperatures

Results from a series of multiaxial loading experiments on the Ti–6Al–4V titanium alloy are presented. Different loading conditions are applied in order to get the comprehensive response of the alloy. The strain rates are varied from the quasi-static to dynamic regimes and the corresponding material responses are obtained. The specimen is deformed to large strains in order to study the material behavior under finite deformation at various strain rates. Torsional Kolsky bar is used to achieve shear strain rates up to 1000 s⁻¹. Experiments are performed under non-proportional loading conditions as well as dynamic torsion followed by dynamic compression at various temperatures. The non-proportional loading experiments comprise of an initial uniaxial loading to a certain level of strain followed by biaxial loading, using a channel-type die at various rates of loadings. All the non-proportional experiments are carried out at room temperature. Experiments are also performed to investigate the anisotropic behavior of the alloy. An orthotropic yield criterion [proposed by Cazacu, O., Plunkett, B., Barlat, F., 2005. Orthotropic yield criterion for hexagonal closed packed metals. International Journal of Plasticity 22, 1171–1194.] for anisotropic hexagonal closed packed materials with strength differential is used to generate the yield surface. Based on the definition of the effective stress of this yield criterion, the observed material response for the different loading conditions under large deformation is modeled using the Khan–Huang–Liang (KHL) equation assuming isotropic hardening. The model constants used in the present study, were pre-determined from the extensive uniaxial experiments presented in the earlier paper [Khan, A.S., Suh, Y.S., Kazmi R., 2004. Quasi-static and dynamic loading responses and constitutive modeling of titanium alloys. International Journal of Plasticity 20, 2233–2248]. The model predictions are found to be extremely close to the observed material response.     

基于结构应力的焊接接头多轴高周疲劳寿命估算

本文对承受弯扭组合载荷下的焊接接头危险点焊趾处进行了疲劳应力分析。结合结构应力考察了在比例载荷和非比例载荷下焊趾处临界面上的应力分量;建立了基于结构应力和修改的Wohler曲线法的临界面上多轴疲劳寿命估算方法;采用该方法对某管板焊接接头进行了多轴估算,将评定结果与文献中的疲劳试验数据做了比较,同包括欧洲钢结构规范3在内的其他的多轴疲劳评定方法相比,本文提出的多轴寿命估算结果最好,而且该方法具有网格划分不敏感性。     

材料超高温动态拉伸SHTB实验方法的有效性分析

针对高温拉伸分离式Hopkinson杆实验技术,通过数值模拟、实验验证以及几种典型材料的高温动态拉伸性能测试相结合的方法,对此实验技术中存在的几个关键问题进行了深入研究。结果表明:对于平板状钩挂式拉伸试样,通过标距段尺寸优化后,应力分布均匀,流动应力曲线与螺纹拉伸试样一致,且应力上升段后没有剧烈跳动;通过精确气动控制,在加载脉冲到来同时,可实现有效的试样快速同步组装和加载;当试样温度为1 200 ℃时,在冷加载杆与高温试样接触以及应力波加载试样的整个过程中,试样平均温度下降约1.3%,而加载杆端温升低于180 ℃。为了验证此实验技术,对3D打印TC4、镍基单晶高温合金DD6进行了最高温度约1 200 ℃时的高温动态拉伸力学性能实验测试。     

金属材料疲劳行为的应力场强法描述

基于近年来发展的应力场地对金属材料的多种疲劳行为作了系统的描述，给出了缺口疲劳系Ｋｆ，疲劳尺寸系数ε，疲劳加载方式因子ＣＬ，多轴疲劳极限方程，缺口件Ｓ－Ｎ曲线的预测等多方面的定量描述，并引用了大量的实验数据加以验证，由此表明应场强法是一种很好的抗疲劳设计方法。     

Effects of laser power density on static and dynamic mechanical properties of dissimilar stainless steel welded joints

The mechanical properties of laser welded joints under impact loadings such as explosion and car crash etc. are critical for the engineering designs. The hardness, static and dynamic mechanical properties of AISI304 and AISI316 L dissimilar stainless steel welded joints by CO₂ laser were experimentally studied. The dynamic strain-stress curves at the strain rate around 10³ s^?1 were obtained by the split Hopkinson tensile bar (SHTB). The static mechanical properties of the welded joints have little changes with the laser power density and all fracture occurs at 316 L side. However, the strain rate sensitivity has a strong dependence on laser power density. The value of strain rate factor decreases with the increase of laser power density. The welded joint which may be applied for the impact loading can be obtained by reducing the laser power density in the case of welding quality assurance.     

镍基单晶合金多轴非比例加载低周疲劳研究

基于正交设计, 分别在680℃和850℃下进行DD3镍基单晶合金薄壁圆管试样([001]取向)拉/扭非比例加载低周疲劳试验, 研究等效应变范围、应变路径角、拉/扭载荷相位角、循环特性和温度诸因素对镍基单晶合金多轴低周疲劳寿命的影响作用. 疲劳试验数据的极差分析表明, 应变路径角、拉/扭载荷相位角和等效应变范围是影响疲劳寿命的主要因素. 将菱形应变加载路径区分为比例加载段和非比例加载段, 提出了表征非比例加载效应的等效应变参量, 并通过引入单晶应变三轴性因子反映拉/扭应变路径角对多轴疲劳寿命的影响. 用考虑非比例加载效应的等效应变范围和单晶应变三轴性因子构造循环塑性应变能损伤参量, 进行多元线性回归分析, 疲劳寿命回归模型与试验寿命具有很好的相关性, 所有试验数据都落在2.0倍的偏差分布带之内.      

Dynamic compressive responses of intact and damaged ceramics from a single split Hopkinson pressure bar experiment

A novel dynamic compressive experimental technique has been developed based on a split Hopkinson pressure bar. This new method dynamically loads the ceramic specimen by two consecutive stress pulses. The first pulse determines the dynamic response of the intact ceramic materiaal and then crushes the specimen, and the second pulse determines the dynamic compressive constitutive behavior of the ceramic rubble. Precise pulse shaping ensures that the specimen deforms at nearly constant strain rates under dynamic stress equilibrium during the loading by both stress pulses. Pulse shaping also controls the amplitudes of loading pulses, the values of strain rates, the maximum strains in the rubble specimens, and the proper separation time between the two loading pulses. The feasibility of the new technique is demonstrated by the experimental results obtained on an AD995 alumina.     

Cyclic multiaxial and shear finite deformation response of OFHC: Part I,experimental results

A series of experiments has been conducted on oxygen free high conductivity (OFHC) copper hollow cylinders under cyclic free-end torsion and biaxial tension–torsion at large strains. In addition, equations are developed to account for the finite rotation and strains in electrical resistance strain gages. In free-end cyclic torsion experiments with shear strain range equal to 23%, a significant strain in the axial direction is observed and it accumulates with a constant rate cycle by cycle. In the biaxial tension–torsion (multiaxial ratchetting) experiments, in which the primary (constant) axial stress is larger than the initial yield stress of the material, the loading conditions are varied to determine the influence of primary axial stress, cyclic shear strain range, pre-cyclic hardening and loading sequence on multiaxial ratchetting. Some important experimental features are high-lighted and recommended to help modeling efforts later.     

铁合金和青铜多孔材料屈服应力的实验研究

对铁合金和青铜多孔材料做静态实验和Taylor冲击实验,得到静态屈服应力和孔隙率以及动态屈服应力和应变率的变化规律,同时将静动态载荷作用下的多孔材料的本构方程与实验结果进行了对比,发现理论分析和实验研究有良好的一致性,表明本文采用的模型基本能满足实际工程应用。     

冲击速度和轴向静载对红砂岩破碎及能耗的影响

地下岩体工程爆破开挖中,距爆源不同距离处岩体承受的地应力和动载荷大小不同,从动载荷的角度表征岩石动态破坏结果与工程实际更吻合。为研究动载荷和地应力大小对岩体破碎和能量耗散特性的影响,利用动静组合加载试验装置,分别设置7个冲击速度和轴向静应力等级,对红砂岩试件进行冲击试验。根据试件的破碎状况,分析不同静应力工况下冲击速度对岩石破坏模式和机理的影响。计算不同工况下的应力波能量值,研究冲击速度和轴向静应力对岩石能耗特性的影响。对破坏试件进行筛分试验,研究岩石破碎分形维数随冲击速度和轴向静应力的变化关系。结果表明,随着冲击速度的增大,试件的破坏程度逐渐加大。无轴压时岩石试件破坏后整体仍是一个圆柱体,属于张拉破坏;有轴压时岩石试件宏观破坏后呈沙漏状,属于拉剪破坏。岩石耗散能随冲击速度的升高呈二次函数关系递增;轴向静应力越高,递增幅度越小。随着冲击速度的升高,岩石分形维数由零逐渐增加;随着轴向静应力的升高,分形维数由零转为大于零的临界冲击速度先升高后降低。