Biodegradation of plasticized poly(vinyl chloride) containing cellulose

The plasticized poly(vinyl chloride) (PVC‐P) and its blend with cellulose (PVC‐P/cell) were prepared by means of extrusion. The samples were then biodegraded in forest soil as well as in soil enriched with cellulolytic microorganisms. Moreover, the samples were vaccinated with chosen species of fungi whose direct effect on polymer was then observed. The course of biodegradation was monitored in terms of, and by means of the following: weight loss, carbon dioxide evolved, attenuated total reflectance infrared (FTIR‐ATR) spectroscopy, gel permeation chromatography (GPC), as well as visual and microscopic observation (OM, SEM). The mechanical properties of samples were studied using the standard tensile tests. It was found that biodegradation in soil occurs in PVC‐P and this process is accelerated in the composition of PVC‐P with cellulose. The biodecomposition yield of PVC‐P/cellulose blends (calculated as relative percentage weight loss) is several dozen times higher than that of PVC‐P. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 903–919, 2007     

Analysis of degradation mechanism of plasticized PVC under artificial aging conditions

A plasticized poly(vinyl chloride) (PVC) has the advantage of low cost, long-term stability and flame resistance among other commodity plastic, and has been in service as a product in railway field. However, the transition of the plasticizer concentration through the degrading condition and its relationship with the mechanical properties, the molecular motion, the appearance of surface and other properties was not clear. These relationships were studied by means of Rheovibron, pulse NMR, GC/MS, GPC, SEM and other methods. The bulk properties show similar change between weathering and thermal aging. In addition, the molecular chain was little influenced, however, the plasticizer concentration shows obviously different transition through each phase of aging conditions. According to the results of the observation of surface and section, different appearances between weathering and thermal aging were indicated and these appearances closely relate to the bulk properties. In conclusion, through the weathering condition, a stepwise flow out of inorganic components and plasticizer was presumable to be a main mechanism of the degradation. On the other hand, through the thermal aging condition, the rearrangement and aggregation of the molecular chain by the annealing effect were conceivable as the main mechanism of the degradation.     

Physico-Mechanical Characteristics of Some EPDM/Plasticized PVC Blends

Summary: In this study were prepared blends based on ethylene propylene terpolymer rubber (EPDM) and plasticized poly (vinyl chloride) (PVC). These blends are immiscible and need to be compatibilized. The following compatibilization methods were used: (1) addition of a compatibilization agent; there were used: maleinized EPDM, maleinized polyethylene (PE), chlorinated polyethylene (CPE) and maleinized polypropylene (PP); chlorinated polyethylene has proved to be the most efficient; the amount of the added CPE giving the best physico-mechanical characteristics was of 7,5 parts to 100 polymer parts; (2) reactive compatibilization, using crosslinked copolymer formation strategy; three different crosslinking systems were used: (a) common method with sulphur and accelerators, (b) crosslinking with benzoyl peroxide and trimethylpropane trimethacrylate (TMPT DL 75), (c) vulcanization with phenol resin and tin chloride. The best physico-mechanical characteristics were obtained with the EPDM/plasticized PVC blends crosslinked with 8 phr phenol resin. Such types of polymer blends can be processed by methods specific for plastics, removing thus vulcanization operation required in case of elastomers. These blends can be used in the manufacture of hoses, gaskets, footwear constituents etc.     

稀土掺杂PVC的紫外及微波交联研究

聚氯乙烯 (ＰＶＣ)是我国目前产量最大 ,应用面最广的高分子原材料。但其耐热性、稳定性及抗老化性都较差。我们考虑到使用稀土掺杂以改进其相关性能 ,同时掺入了少量从水玻璃中提取出来的活性硅醇到ＰＶＣ中以增加其柔性 ,探索了紫外辐射交联和微波辐射交联对ＰＶＣ机械力学性能的影响。本文采用ＰＶＣ流延膜来进行辐射交联并测定样品的力学性能。结果发现 ,稀土掺杂的结果使得样品的扯断伸长率大幅度提高 ,拉伸强度上升显著。而添加活性硅醇后ＰＶＣ流延膜的扯断伸长率进一步提高 ,拉伸强度则下降 ,柔性得以提高。将氯化钕溶于 95 %的乙醇…     

Effects of Epoxidation Content of ENR on Morphology and Mechanical Properties of Natural Rubber Blended PVC

This research work has concerned a study on toughness of PVC/natural rubber (NR) blends compatibilized with epoxidized natural rubber (ENR). The aim of this work was to investigate the effect of degree of epoxidation on morphology and mechanical properties of the blends. Epoxidized natural rubber with a variety of epoxidation contents were prepared by reacting the NR latex with formic acid and hydrogen peroxide at various chemical contents. Chemical structure and epoxidation content of epoxidized natural rubber were evaluated by FTIR and ¹H-NMR techniques. After that, three grades of ENR with epoxidation contents of 15, 25 and 42 % (by mole) were further used for blending with PVC and NR in an internal mixer at 60 rpm and at 170 °C. From tensile and impact tests, it was found that tensile elongation and impact strength of the materials remarkably increased with degree of epoxidation. On the other hand, tensile strength and modulus of the materials rarely changed with the epoxidation content. An increase in toughness of the blends with epoxidation content was related to a better molecular interaction between PVC and ENR as suggested by torque-time curves of the materials.     

Development of PVC/Silica Hybrids Using PVC Plastisols

A novel method for producing a plasticised PVC with increased porosity has been developed, by the use of an organic-inorganic hybrid. Silica was produced in situ from tetraethoxysilane via a hydrolytic sol-gel processing route. Tetrahydrofuran was used as co-solvent, and γ-glycidyloxypropyl-trimethoxysilane as coupling agent. The films produced were transparent, with moderate mechanical properties. A film containing 20% silica showed a 45% increase in water vapour permeability.     

Preparation and properties of composites made from rice straw and poly(vinyl chloride) (PVC)

Rice straw was employed for the preparation of lignocellulosic‐poly(vinyl chloride) (PVC) composites. The effect of pretreatment of rice straw, concentration of PVC, pressure as well as pressing temperature on the mechanical properties and water absorption was studied. Also, the effect of lignin as coupling agent on the mechanical properties and water absorption of composite was studied. Composites of rice straw comprising both PVC and a coupling agent offer superior properties compared to those made from only rice straw and PVC. The extent of improvement in the mechanical properties and dimensional stability of composites depended not only on the pretreatment of rice straw, concentration of PVC and lignin but also on pressure and pressing temperature. Copyright © 2004 John Wiley & Sons, Ltd.     

NMR STUDY ON THE COMPATIBILITY OF ACR/PVC BLENDS

A 300MHz solid NMR study on the compatibility of ACR (poly (methyl methacrylate-co-methacrylate), in the ratio of 1:1)-PVC (poly (vinyl chloride)) blends is reported. Spin-lattice (T_1) and spin-spin (T_2) relaxation time of ACR, PVC and their blends are recorded in the temperature range from 215K to 355K. Experimental results indicate that ACR and PVC are compatible with each other and the domain size is smaller than 25 nm, but heterogeneit(?)s of molecular dimensions still exist. Some problems of mechanism of compatibility and data analysis are also discussed.     

Development and characterization of reactive extruded PVC/polyacrylate blends

This paper describes a method to obtain polymer blends by the absorption of a liquid solution of monomer, initiator, and a crosslinking agent in suspension type porous poly(vinyl chloride) (PVC) particles, forming a dry blend. These PVC/monomer dry blends are reactively polymerized in a twin‐screw extruder to obtain the in situ polymerization in a melt state of various blends: PVC/poly(methyl methacrylate) (PVC/PMMA), PVC/poly(vinyl acetate) (PVC/PVAc), PVC/poly(butyl acrylate) (PVC/PBA) and PVC/poly(ethylhexyl acrylate) (PVC/PEHA). Physical PVC/PMMA blends were produced, and the properties of those blends are compared to reactive blends of similar compositions. Owing to the high polymerization temperature (180°C), the polymers formed in this reactive polymerization process have low molecular weight. These short polymer chains plasticize the PVC phase reducing the melt viscosity, glass transition and the static modulus. Reactive blends of PVC/PMMA and PVC/PVAc are more compatible than the reactive PVC/PBA and PVC/PEHA blends. Reactive PVC/PMMA and PVC/PVAc blends are transparent, form single phase morphology, have single glass transition temperature (T_g), and show mechanical properties that are not inferior than that of neat PVC. Reactive PVC/PBA and PVC/PEHA blends are incompatible and two discrete phases are observed in each blend. However, those blends exhibit single glass transition owing to low content of the dispersed phase particles, which is probably too low to be detected by dynamic mechanical thermal analysis (DMTA) as a separate T_g value. The reactive PVC/PEHA show exceptional high elongation at break (～90%) owing to energy absorption optimized at this dispersed particle size (0.2–0.8 µm). Copyright © 2005 John Wiley & Sons, Ltd.     

Structure of reactively extruded rigid PVC/PMMA blends

A novel route for producing polymer blends by reactive extrusion is described, starting from poly (vinyl chloride)/methyl methacrylate (PVC/MMA) dry blend and successive polymerization of MMA in an extruder. Small angle X‐ray scattering (SAXS) measurements were applied to study the monomer's mode of penetration into the PVC particles and to characterize the supermolecular structure of the reactive poly(vinyl chloride)/poly(methyl methacrylate) (PVC/PMMA) blends obtained, as compared to the corresponding physical blends of similar composition. These measurements indicate that the monomer molecules can easily penetrate into the PVC sub‐primary particles, separating the PVC chains. Moreover, the increased mobility of the PVC chains enables formation of an ordered lamellar structure, with an average d‐spacing of 4.1 nm. The same characteristic lamellar structure is further detected upon compression molding or extrusion of PVC and PVC/PMMA blends. In this case the mobility of the PVC chains is enabled through thermal energy. Dynamic mechanical thermal analysis (DMTA) and SAXS measurements of reactive and physical PVC/PMMA blends indicate that miscibility occurs between the PVC and PMMA chains. The studied reactive PVC/PMMA blends are found to be miscible, while the physical PVC/PMMA blends are only partially miscible. It can be suggested that the miscible PMMA chains weaken dipole–dipole interactions between the PVC chains, leading to high mobility and resulting in an increased PVC crystallinity degree and decreased PVC glass transition temperature (T_g). These phenomena are shown in the physical PVC/PMMA blends and further emphasized in the reactive PVC/PMMA blends. Copyright © 2005 John Wiley & Sons, Ltd.     

Cationic grafting of olefins from PVC: The effect of reaction conditions

The cationic grafting of isobutylene, styrene, α-methylstyrene, and β-pinene from a poly(vinyl chloride) (PVC) backbone was investigated. Grafting-from was induced by Et₂AlCl in 1,2-dichloroethane and methylene dichloride solutions from 20 to −70 °C. The effects of temperature and proton trap [2,6-di-tert-butylpyridine (DtBP)] on grafting-from efficiency (G_eff), extent of grafting, branch length (molecular weight), and number of branches per PVC molecule were determined. Reducing the temperature invariably increased the G_eff and the molecular weight of polyisobutylene, polystyrene, poly(α-methylstyrene), and poly(β-pinene) branches attached to PVC. The magnitude of the effects was different with the various olefins and depended on the reaction conditions. The effect of DtBP was examined in the 5 × 10⁻⁴–4 × 10⁻³ mol/L range. By increasing the DtBP concentration the G_eff increased; however, the number-average molecular weight of the grafted branches decreased. The lengths of the grafted branches can be controlled, and G_eff's close to 100% were obtained. The fact that the proton trap reduced the molecular weights of grafted branches suggests that besides proton scavenging, DtBP may also abstract protons from the growing carbenium ion site. © 2001 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 1675–1680, 2001     

Preparation and characterization of PVC/PANI conductive composite with extremely low percolation threshold

Aniline was polymerized in the presence of poly(vinyl chloride) (PVC) powders in hydrochloric acid to in situ prepare poly(vinyl chloride)/polyaniline (PVC/PANI) composite particles. UV‐vis spectra and FT‐IR spectra indicate PANI in PVC/PANI composite particles possessed a higher oxidation state with decreased aniline content in reactants. Both conductivity and impact strength of the dodecylbenzenesulfonic acid (DBSA) doped PANI composites (PVC/PANI‐DBSA), which were compression molded from the in situ prepared PVC/PANI particles, increase with the pressing temperature and decrease with the increase of DBSA doped PANI (PANI‐DBSA) loading. An excellent electric conductivity of 5.06 × 10^?2 S/cm and impact strength of 0.518 KJ/m² could be achieved for the in situ synthesized and subsequently compression molded composite. Copyright © 2004 John Wiley & Sons, Ltd.     

Overview of the recent literature on flame retardancy and smoke suppression in PVC

This paper presents an overview of the recent literature on flame retardancy of poly(vinyl chloride) (PVC). A short overview of mechanisms of thermal decomposition of PVC, especially those which lead to char formation, is also presented because this gives insight into the mechanisms of flame retardant action. New developments in the area are mostly focused on combinations of various flame retardants and smoke suppressants in the search for synergistic effects. Because different additives show different mechanisms of action, synergistic combinations are very probable. New developments in phosphate ester plasticizers are reported in the literature. Copyright © 2005 John Wiley & Sons, Ltd.     

Tailoring the desired optical and mechanical performance of polyester‐plasticized PVC films: the role of different light stabilizers on the photo‐degradation

Effect of hindered amine light stabilizer (HALS: C944) and ultraviolet absorbers (UVAs: UV326, UV531) on the photo‐stabilities of polyester‐plasticized poly(vinyl chloride) (PVC) and polyester‐plasticized PVC/pigment yellow (PY) films were studied systematically. Both ultraviolet absorbers (UVAs) and hindered amine light stabilizer (HALS) could slow down the discoloration of polyester‐plasticized PVC and polyester‐plasticized PVC/PY films. However, the addition of UVAs protected polyester‐plasticized PVC films from being discolored and its efficiency is higher than HALS. The specific order of stabilizing effect on the photo‐oxidation is UV326 > UV531 > C944. For the optical performance, both UVAs and HALS could help to maintain the transmittance of visible light after photo‐degradation. The former could effectively adsorb ultraviolet (UV) light and resulted in lower transmittance of UV light. For the polyester‐plasticized PVC/PY systems, even though HALS and UVAs cannot help to maintain the shielding ability in high‐energy visible region after UV irradiation, they can help prevent the loss in transmittance of visible light. The surface morphology exhibited small holes on the surface of the films that contain UV531 or UV326; while large and deep holes were observed on the surface of PVC films without additives, C944‐doped and C944/PY‐doped films, indicating the higher UV‐stabilizing effect of UVAs. With regard to mechanical properties, UVAs and HALS can help to prevent the loss. Our present study systematically revealed the role of different stabilizers on the polyester‐plasticized PVC and polyester‐plasticized PVC/PY systems and paved the way to offer PVC materials with functional optical performance and desired long‐term performance using different light stabilizers. Copyright © 2017 John Wiley & Sons, Ltd.     

Synthesis of Bimodal PVC Latexes by Emulsion Polymerization: An Experimental and Modeling Study

The onset and extent of secondary particle formation in the seeded emulsion polymerization of vinyl chloride were investigated by performing a series of seeded polymerizations at different concentrations of seed latex and surfactant. It was found that, in general, both the onset and the extent of secondary particle formation are determined not only by the rate of homogeneous nucleation, but also by the rates of particle coagulation. A comparison of methods to compute the evolution of the particle size distribution in vinyl chloride emulsion polymerization was also carried out. For growth processes, the widely-used pseudo-bulk model gives correct answers. For processes involving particle formation, on the other hand, this model cannot be used because it neglects, among others, the effects of nucleation and coagulation on the radical number distribution. To surmount this problem, we propose to use the zero-one-two model, for which the full population balance equations are given here.     

Molecular orientation behavior of poly(vinyl chloride) as influenced by the nanoparticles and plasticizer during uniaxial film stretching in the rubbery stage

The structural evolution during uniaxial stretching of poly(vinyl chloride) films was studied using our real time spectral birefringence stretching machine. The effect of clay loading and the amount of plasticizer as well as the rate effects on the birefringence development and true mechanical response are presented with a final model summarizing the molecular phenomena during stretching. Mechano‐optical studies revealed that birefringence correlated with mechanical response (stress, strain, work) nonlinearly. This was primarily attributed to the preexisting strong network of largely amorphous chains connected via small crystallites that act as physical crosslinking points. These crystallites are not easily destroyed during the high‐speed stretching process as evidenced from the birefringence–true strain curves along with the X‐ray crystallinity measurements. At high speeds, the amorphous chains do not have enough time to relax and hence attain higher orientation levels. The crystallites, however, orient more efficiently when stretched at slow speeds. Apparently, some relaxation of the surrounding amorphous chains helps rotate the crystallites in the stretching direction. Overall birefringence is higher at high stretching speeds for a given true strain value. When the nanoparticles are incorporated, the orientation levels are increased significantly for both the crystalline and amorphous phases. Nanoplatelets increase the continuity of the network because they have strong interaction with the amorphous chains and/or crystallites. This in turn helps transfer the local stresses to the attached chains and increase the orientation levels of the chains. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 724–742, 2005     

Migration of Additives from Poly(vinyl chloride) (PVC) Tubes into Aqueous Media

The stability and migration product of medical PVC tubes plasticized with polyadipates were investigated by ageing in phosphate buffer at pH 1.679 and water at different temperatures. Changes in the PVC tubes were studied by water absorption, weight loss, Fourier infrared spectroscopy (FTIR), differential scanning calorimetry (DSC) and thermal gravimetric analysis (TGA). The low molecular weight migration product that was released was extracted and silylanized before gas chromatography/mass spectroscopy (GC/MS) identification and quantification. After 70 days, the weight loss was less than 0.5% and only a small amount of adipic acid migrated when a tube was aged at 37°C in water and phosphate buffer (pH 1.679), and at 70°C in water after 56 days. However, when aged at 70 and 110°C, gradual deactivation of heat stabilizer after 21 days of ageing in buffer solution and separation of plasticizer from PVC matrix occurred. When the tube was aged at 110°C, significant degradation of both polyadipates and PVC were observed. Adipic acid and 1,4-butanediol monomers and oligomers of polyadipate were the major migration products from polyadipates in the water ageing solution, while only a relatively high amount of adipic acid was identified as the main product in the buffer ageing solution.     

Antimicrobial,mechanical, optical and thermal properties of PVC/ZnO‐EDTA nanocomposite films

Covalent surface functionalization of synthesized ZnO nanoparticles (NP)s with ethylenediaminetetraacetic acid (EDTA) was successfully carried out. Modified ZnO‐EDTA NPs as a viable and inexpensive filler were incorporated into poly(vinyl chloride) PVC matrix after their chemical modification to investigate the agglomeration behavior. All prepared materials including modified NPs and PVC/ZnO‐EDTA nanocomposites (NC)s were analyzed by Fourier transform infrared spectroscopy, ultraviolet–visible spectroscopy, thermogravimetric analysis, X‐ray diffraction, field emission scanning electron microscopy and transmission electron microscopy. Fabricated PVC/ZnO‐EDTA NCs were reported to have high transparency and improved mechanical properties compared with PVC. Modified ZnO and the fabricated NCs were shown to exhibit excellent antibacterial activity against two bacteria species: Escherichia coli and Staphylococcus aureus. The obtained NCs could be considered as self‐extinguishing materials on the basis of the LOI values. Copyright © 2016 John Wiley & Sons, Ltd.     

Evaporative loss kinetics of di(2-ethylhexyl)phthalate (DEHP) from pristine DEHP and plasticized PVC

The migration of di(2-ethylhexyl)phthalate (DEHP) from poly(vinyl chloride) (PVC) to a surrounding gas phase at temperatures below 120 °C kinetically is controlled by evaporation. The effects on the DEHP loss rate of nitrogen flow rate, relative humidity and degradation of the plasticizer at 100 °C was assessed. The sample mass decreased linearly with time for both pristine DEHP and plasticized PVC at comparable rates, suggesting that a thin film of DEHP was present on the jacketing insulation during desorption. The latter hypothesis was supported by infrared spectroscopy and by the fact that DEHP is an amphiphilic molecule that will tend to aggregate at the surface with the hydrophobic 2-ethylhexyl units at the air interface. The effect on the migration rate of moisture present in the gas phase was negligible. The DEHP loss rate increased in a retarding non-linear fashion with increasing gas flow rate. In one of the experiments, DEHP was accidently degraded as revealed by discoloration, the presence of low molar mass degradation products (liquid chromatography) containing additional carbonyl groups (infrared spectroscopy) and an increase in the evaporation rate at temperatures between 100 and 130 °C.     

Covalently Linked Plasticizers: Triazole Analogues of Phthalate Plasticizers Prepared by Mild Copper‐Free “Click” Reactions with Azide‐Functionalized PVC

Copper‐free azide‐alkyne click chemistry is utilized to covalently modify polyvinyl chloride (PVC). Phthalate plasticizer mimics di(2‐ethylhexyl)‐1H‐triazole‐4,5 dicarboxylate (DEHT), di(n‐butyl)‐1H‐1,2,3‐triazole‐4,5‐dicarboxylate (DBT), and dimethyl‐1H‐triazole‐4,5‐dicarboxylate (DMT) are covalently attached to PVC. DEHT, DBT, and DMT have similar chemical structures to traditional plasticizers di(2‐ethylhexyl) phthalate (DEHP), di(n‐butyl) phthalate (DBP), and dimethyl phthalate (DMP), but pose no danger of leaching from the polymer matrix and forming small endocrine disrupting chemicals. The synthesis of these covalent plasticizers is expected to be scalable, providing a viable alternative to the use of phthalates, thus mitigating dangers to human health and the environment.