Optimization of a Liquid–Liquid Extraction Procedure of Butyltin Compounds and Total Tin in Marine Water Samples Using Flame Atomic Absorption Spectrometry

Two liquid–liquid extraction procedures have been optimized for analysis of sea water samples. Tributyltin (TBT), dibutyltin (DBT), and monobutyltin (MBT) compounds were extracted with tropolone in chloroform from samples acidified to 1Mwith HCl. The extracts were evaporated to dryness and redissolved in methanol, prior to separation of the alkytin compounds by liquid chromatography. Total tin was extracted from samples at pH 2 using oxine in isobutylmethylketone (IBMK). The optimized extraction procedure for alkyltin compounds was used as a pretreatment of the samples when the speciation of tin was being performed. The IBMK solutions obtained from the extraction of total tin were directly subjected to electrothermal atomic absorption spectrometry, using zirconium-coated graphite tubes with L'vov platforms.     

A new approach based on a combination of direct and headspace cold-fiber solid-phase microextraction modes in the same procedure for the determination of polycyclic aromatic hydrocarbons and phthalate esters in soil samples

This study describes a new approach to cold-fiber solid-phase microextraction (CF-SPME) based on a combination of different extraction modes in the same extraction procedure. Also, the high quantity of water required to facilitate both the desorption of analytes from the matrix and their transport to the fiber coating is reported. The extraction mode was changed from the direct to the headspace mode in a single extraction while manipulating the extraction times and coating temperature to improve the extraction of compounds with different volatilities. Compounds with low volatility were better extracted in the direct mode, while the headspace mode was more appropriate for volatile compounds. Polycyclic aromatic hydrocarbons (PAHs) and phthalic acid esters (PEs) in sand or soil samples were used as model compounds and matrices in this study. The optimized conditions were: sample pH in the range of 4-7, addition of 12 mL of 194 g L(-1) aqueous NaCl solution in a 15 mL vial, and 80 min total extraction time with a sample temperature of 90°C (50 min in direct mode with coating at 90°C followed by 30 min in headspace mode with coating at 30°C). The proposed procedure was compared with conventional CF-SPME (with and without addition of water) and was found to be more effective for all the analytes, since it is capable of extracting both heavier and lighter compounds from soil samples in a single extraction procedure. The use of an excess of water and a combination of extraction modes in the same CF-SPME procedure are the main factors responsible for this enhancement. The proposed method was applied to the extraction of PAHs and PEs in spiked soil samples and excellent results were obtained for most of the compounds evaluated.     

Glass-fiber reinforced poly(acrylate)-based sorptive materials for the enrichment of organic micropollutants from aqueous samples

A novel and simple approach to sorptive materials for the extraction of organic compounds from environmental samples is presented. It entails the use of glass fiber fabric strips coated with a customized poly(acrylate) (PA) formulation as extraction medium. Analytes were enriched by means of shaking of the PA strip in the sample and then subsequently thermally desorbed and analyzed by GC-MS. The performance of the sorptive materials was evaluated by the enrichment of compounds with different polarities (phenols, hexachlorobenzene and hexachlorocyclohexanes) from water samples. Parameters that affect the extraction process such as pH, ionic strength of the solvent, mixing mechanism, extraction time and desorption conditions were investigated. The extraction abilities of the PA extraction medium were compared with that of commercially available poly(dimethylsiloxane) (PDMS) Twisters. The results revealed that the new material shows higher affinity for phenolic compounds presumably due to the presence of polar groups. The partition coefficients for the PA strips estimated in this work were up to 15 times higher than for the PDMS Twister, resulting in higher recoveries and lower detection limits. The method was applied for the quantification of the aforementioned compounds in contaminated surface water samples from Bitterfeld (Germany). Using both PA strips and PDMS Twisters, good agreement of the extraction data was achieved.     

Ionic liquid-salt aqueous two-phase extraction based on salting-out coupled with high-performance liquid chromatography for the determination of sulfonamides in water and food

Ionic liquid-salt aqueous two-phase extraction coupled with high-performance liquid chromatography with ultraviolet detection was developed for the determination of sulfonamides in water and food samples. In the procedure, the analytes were extracted from the aqueous samples into the ionic liquid top phase in one step. Three sulfonamides, sulfamerazine, sulfamethoxazole, and sulfamethizole were selected here as model compounds for developing and evaluating the method. The effects of various experimental parameters in extraction step were studied using two optimization methods, one variable at a time and Box–Behnken design. The results showed that the amount of sulfonamides did not have effect on the extraction efficiency. Therefore, a three-level Box–Behnken experimental design with three factors, which combined the response surface modeling, was used to optimize sulfonamides extraction. Under the most favorable extraction parameters, the detection limits (S/N?=?3) and quantification limits (S/N?=?10) of the proposed method for the target compounds were achieved within the range of 0.15–0.3 ng/mL and 0.5–1.0 ng/mL from spiked samples, respectively, which are lower than or comparable with other reported approaches applied to the determination of the same compounds. Finally, the proposed method was successfully applied to the determination of sulfonamide compounds in different water and food samples and satisfactory recoveries of spiked target compounds in real samples were obtained.     

Ionic Liquid–Liquid Extraction and Supported Liquid Membrane Analysis of Lipophilic Wood Extractives from Dissolving-Grade Pulp

In this study, the extraction of lipophilic wood extractives from dissolving pulp samples using ionic liquid–liquid extraction and a two phase hollow fibre supported liquid membrane was investigated. Ionic liquids are capable of dissolving a range of organic and polymeric compounds and are biodegradable, with a negligible vapour pressure. Pulp samples were dissolved in a suitable amount of molten 1-butyl-3-methylimidazolium chloride to give 5 % cellulose solution. Pure cellulose was regenerated by adding water and filtered off. The ionic liquid-aqueous filtrate was first extracted for lipophilic extractives using liquid–liquid extraction. Then, a two phase hollow fibre supported liquid membrane extraction of lipophilic extractives was performed to extract the derivatized compounds prior to analysis by gas chromatography mass spectrometry. The operational parameters of this sample preparation approach were optimised using sterols and fatty acid methyl esters. The variation of enrichment factors and extraction efficiency with respect to liquid membrane, extraction time, stirring speed and sample pH were observed and used to get the optimal parameters. The approach was used in the analysis of oxygen bleached dissolving pulp samples in which main compounds identified were fatty acids, sterols, fatty alcohols, steroid hydrocarbons and ketones. These compounds were similar to those obtained using molecular solvent extraction method, which indicated the absence of chemical reaction between extractives and ionic liquid used.

     

Membrane-assisted solvent extraction coupled to large volume injection–gas chromatography–mass spectrometry for the determination of a variety of endocrine disrupting compounds in environmental water samples

Membrane-assisted solvent extraction coupled to large volume injection in a programmable temperature vaporisation injector using gas chromatography–mass spectrometry analysis was optimised for the simultaneous determination of a variety of endocrine disrupting compounds in environmental water samples (estuarine, river and wastewater). Among the analytes studied, certain hormones, alkylphenols and bisphenol A were included. The nature of membranes, extraction solvent, extraction temperature, solvent volume, extraction time, ionic strength and methanol addition were evaluated during the optimisation of the extraction. Matrix effects during the extraction step were studied in different environmental water samples: estuarine water, river water and wastewater (influent and effluent). Strong matrix effects were observed for most of the compounds in influent and effluent samples. Different approaches were studied in order to correct or minimise matrix effects, which included the use of deuterated analogues, matrix-matched calibration, standard addition calibration, dilution of the sample and clean-up of the extract using solid-phase extraction (SPE). The use of deuterated analogues corrected satisfactorily matrix effect for estuarine and effluent samples for most of the compounds. However, in the case of influent samples, standard addition calibration and dilution of the sample were the best approaches. The SPE clean-up provided similar recoveries to those obtained after correction with the corresponding deuterated analogue but better chromatographic signal was obtained in the case of effluent samples. Method detection limits in the 5–54 ng L⁻¹ range and precision, calculated as relative standard deviation, in the 2–25% range were obtained.     

Tartaric acid extraction of organotin compounds from sediment samples

A new extraction method for the determination of tributyltin (TBT), dibutyltin (DBT) and monobutyltin (MBT) in sediments based on extraction with tartaric acid and methanol has been developed. Tin species were extracted from sediment samples using focused microwave technology, then ethylated with sodium tetraethylborate (NaBEt₄) and analyzed by isotope dilution (ID) gas chromatography-mass spectrometry (GC-MS). The advantages of such methodology in comparison with other established extraction methods for the routine speciation analysis of organotin compounds are discussed with respect to sulfur interferences co-extracted from complex matrices.Interferences from elemental sulfur are normally found with acetic acid extraction, but with tartaric acid extraction these interferences were eliminated, demonstrating selective extraction.The accuracy of the analytical procedure was established by analyzing a certified reference material (CRM) (PACS-2, marine sediment) and comparing the results to the certified values. Good agreement between determined and certified values for butyltin compounds was obtained. Finally, some complex sediment samples collected from San Vicente's Bay, Chile, were analyzed with the proposed methodology, demonstrating its potential value for monitoring butyltins in environmental samples with high concentrations of sulfur compounds.     

Application of ionic liquids in the microwave-assisted extraction of polyphenolic compounds from medicinal plants

Ionic liquids (ILs) solutions as solvents were successfully applied in the microwave-assisted extraction (MAE) of polyphenolic compounds from medicinal plants. ILs, its concentration and MAE conditions were investigated in order to extract polyphenolic compounds effectively from Psidium guajava Linn. (P. guajava) leaves and Smilax china (S. china) tubers. The results obtained indicated that the anions and cations of ILs had influences on the extraction of polyphenolic compounds as well as the ILs with electron-rich aromatic π-system enhanced extraction ability. Under the optimized conditions, the extraction yields of the polyphenolic compounds were in the range of 79.5-93.8% with one-step extraction, and meanwhile the recoveries were in the range of 85.2-103% with relative standard deviations (R.S.D.s) lower than 5.6%. Compared to conventional extraction procedures, the results suggested that the proposed method was effective and alternative for the extraction of polyphenolic compounds from medicinal plants. In addition, the extraction mechanisms and the structures of samples before and after extraction were also investigated. ILs solutions as green solvents in the MAE of polyphenolic compounds from medicinal plant samples showed a great promising prospect.     

Multi‐residue method for the analysis of pharmaceutical compounds in sewage sludge,compost and sediments by sonication‐assisted extraction and LC determination

A method for the simultaneous determination of 16 pharmaceutical compounds in three types of sewage sludge (primary, secondary and anaerobically digested dehydrated sludge), compost and sediment samples is described. Pharmaceutical compounds evaluated were nonsteroidal anti‐inflammatory drugs (acetaminophen, diclofenac, ibuprofen, ketoprofen, naproxen and salicylic acid), antibiotics (sulfamethoxazole and trimethoprim), an anti‐epileptic drug (carbamazepine), a β‐blocker (propranolol), a nervous stimulant (caffeine), estrogens (17α‐ethinylestradiol, 17β‐estradiol, estriol and estrone) and lipid regulators (clofibric acid, metabolite of clofibrate and gemfibrozil). The method is based on the ultrasonic‐assisted extraction, clean‐up by SPE and analytical determination by HPLC with diode array and fluorescence detectors. The best extraction recoveries were achieved in a three‐step extraction procedure with methanol and acetone as extraction solvents. Extraction recoveries of several pharmaceutical compounds as caffeine were highly dependent on the type of sample evaluated. The applicability of the method was tested by analyzing primary, secondary and anaerobically digested dehydrated sludge, compost and sediment samples from Seville (Southern Spain). Ten of the sixteen pharmaceutical compounds were detected in sludge samples and five in compost and sediment samples. The highest concentration levels were recorded for ibuprofen in sewage samples, whereas salicylic acid and 17α‐ethinylestradiol were detected in all of the samples analyzed.     

Simultaneous determination of the endocrine disrupting compounds nonylphenol, nonylphenol ethoxylates, triclosan and bisphenol A in wastewater and sewage sludge by gas chromatography-mass spectrometry

An integrated analytical method for the simultaneous determination of 4-n-nonylphenol (4-n-NP), nonylphenol monoethoxylate (NP1EO), nonylphenol diethoxylate (NP2EO), bisphenol A (BPA) and triclosan (TCS) in wastewater (dissolved and particulate phase) and sewage sludge was developed based on gas chromatography-mass spectrometry. Chromatographic analysis was achieved after derivatization with bis(trimethylsilyl)trifluoroacetamide (BSTFA). Extraction from water samples was performed by solid-phase extraction (SPE). The optimization of SPE procedure included the type of sorbent and the type of the organic solvent used for the elution. Referred to solid samples, the target compounds were extracted by sonication. In this case the optimization of the extraction procedure included the variation of the amount of the extracted biomass, the duration and the temperature of sonication and the type of the extraction organic solvent. The developed extraction procedures resulted in good repeatability and reproducibility with relative standard deviations (RSDs) less than 13% for all the tested compounds for both types of samples. Satisfactory recoveries were obtained (>60%) for all the compounds in both liquid and solid samples, except for 4-n-NP, which gave recoveries up to 35% in wastewater samples and up to 63% in sludge samples. The limits of detection (LODs) of the target compounds varied from 0.03 (4-n-NP) to 0.41 microg l(-1) (NP2EO) and from 0.04 (4-n-NP) to 0.96 microg kg(-1) (NP2EO) for liquid and solid samples, respectively. The developed methods were successfully applied to the analysis of the target compounds in real samples.     

Determination of organotin compounds in environmental samples by supercritical fluid extraction and gas chromatography with atomic emission detection

The extraction of six tetraalkyltin and seven ionic organotin compounds from spiked topsoil samples with supercritical carbon dioxide and carbon dioxide modified with 5 percent methanol was investigated. Analysis of the soil extracts was performed by gas chromatography with atomic emission detection. Retention times, minimum detectable concentrations, and detector linear ranges are included for nine organotin compounds (seven of the nine compounds were derivatized with n-pentylmagnesium bromide prior to gas chromatographic analysis). A 2³ factorial experimental design was used to study the effect of three variables (pressure, temperature, and extraction time) on compound recovery. The results indicate that the tetraalkyltin compounds are extracted from topsoil samples with recoveries ranging from 90 to 110 percent. Recoveries for the ionic organotin compounds ranged from 50 to 75 percent for trimethyltin chloride, triethyltin bromide, and tributyltin iodide; they were below 20 percent for dimethyltin dichloride, dibutyltin dichloride, diphenyltin dichloride, and butyltin trichloride. When sodium diethyldithiocarbamate was added to the soil samples prior to extraction, followed by extraction with carbon dioxide modified with 5 percent methanol, recoveries ranged from 70 to 90 percent for trimethyltin chloride, triethyltin bromide, dimethyltin dichloride, tributyltin iodide, and dibutyltin dichloride; recoveries were approximately 40 percent for butyltin trichloride and diphenyltin dichloride.     

Development of a stir bar sorptive extraction method for the determination of volatile compounds in orange juices

A stir bar sorptive extraction method for the determination of volatile compounds in orange juices was developed. The extraction variables were optimized using a reduced two‐level factorial screening design (2^5‐1), and the most suitable analytical conditions for the extraction of the studied compounds were: sample volume 10 mL, extraction time 60 min, stirring speed 1800 rpm, NaCl amount 30% (weight/volume), and twister length 10 mm. The optimized method was further validated, obtaining good linearity and detection and quantification limits low enough to correctly determine the studied compounds. As well, for most of the studied compounds precision and recovery values were good. Several orange juice samples (squeezed and commercial) were extracted following the optimized extraction method and analyzed by gas chromatography coupled to mass spectrometry detection. The method has proven to be suitable for the determination of the aroma of orange juice, of which limonene was the major volatile compound in all the studied samples.     

Selective extraction of triazine herbicides based on a combination of membrane assisted solvent extraction and molecularly imprinted solid phase extraction

A selective extraction technique based on the combination of membrane assisted solvent extraction and molecularly imprinted solid phase extraction for triazine herbicides in food samples was developed. Simazine, atrazine, prometon, terbumeton, terbuthylazine and prometryn were extracted from aqueous food samples into a hydrophobic polypropylene membrane bag containing 1000μL of toluene as the acceptor phase along with 100mg of MIP particles. In the acceptor phase, the compounds were re-extracted onto MIP particles. The extraction technique was optimised for the type of organic acceptor solvent, amount of molecularly imprinted polymers particles in the organic acceptor phase, extraction time and addition of salt. Toluene as the acceptor phase was found to give higher triazine binding onto MIP particles compared to hexane and cyclohexane. Extraction time of 120min and 100mg of MIP were found to be optimum parameters. Addition of salt increased the extraction efficiency for more polar triazines. The selectivity of the technique was demonstrated by extracting spiked cow pea and corn extracts where clean chromatograms were obtained compared to only membrane assisted solvent extraction or only molecularly imprinted solid phase extraction. The study revealed that this combination may be a simple way of selectively extracting compounds in complex samples.     

Development of a sensitive determination method for benzotriazole UV stabilizers in enviromental water samples with stir bar sorption extraction and liquid desorption prior to ultra‐high performance liquid chromatography with tandem mass spectrometry

Benzotriazole UV stabilizers are emerging compounds used in personal care products and can enter surface water after passing through wastewater treatment plants without being removed. Because these analytes are strongly hydrophobic, there is an environmental risk of accumulation in solid matrices and magnification through the trophic chain. In this work, a method based on stir bar sorption extraction with liquid desorption is presented for the extraction of benzotriazole UV stabilizers from water samples. Stir bar sorptive extraction was combined with ultra‐high performance LC with MS/MS detection. All important factors affecting the stir bar sorptive extraction procedure are discussed, and the optimized method was applied to seawater and wastewater samples from Gran Canaria Island, providing good selectivity and sensitivity with LODs and limits of quantification in the range of 18.4–55.1 and 61.5–184 ng/L, respectively. Recoveries between 68.4–92.2% were achieved for the more polar compounds, whereas the recoveries were lower for the two less polar compounds, most likely due to their strong absorption into the polydimethylsiloxane stir bar phase that does not allows the complete desorption. The repeatability studies gave RSDs of between 6.45 and 12.6% for all compounds in the real samples.     

Study of the effect of different fiber coatings and extraction conditions on dry cured ham volatile compounds extracted by solid-phase microextraction (SPME)

Extraction of dry cured ham volatile compounds by solid-phase microextraction (SPME) was optimized. Different fiber coatings (carboxen/polydimethylsiloxane (CAR/PDMS), divinylbenzene/carboxen/polydimethylsiloxane (DVB/CAR/PDMS), polydimethylsiloxane (PDMS), polydimethylsiloxane/divinylbenzene (PDMS/DVB)), times of extraction (15, 30, 60 min) and sample preparation (ground samples and homogenates with NaCl saturated solution) were assayed. CAR/PDMS and DVB/CAR/PDMS fiber coatings extracted more than 100 volatile compounds and showed the highest area counts for most volatile compounds. CAR/PDMS coating extracted better those compounds whose Kovats index (KI) was lower than 980 (on average) and DVB/CAR/PDMS those with higher KI. Fifteen minutes of extraction provided a volatile compound profile with lower area counts for most compounds and qualitatively different to that obtained with 30 and 60 min of extraction. Homogenates gave a different profile compared to ground samples, with lower total counts for most compounds but higher proportion of aldehydes, and presence of several compounds not found in ground samples.     

SPE – Microwave‐assisted extraction coupled system for the extraction of pesticides from water samples

SPE is a commonly applied technique for preconcentration of pesticides from water samples. Microwave‐assisted extraction (MAE) technique is the extraction applied for preconcentration of different compounds from solid samples. SPE coupled with MAE is capable of preconcentrating these compounds from water samples too. This investigation was aimed at improving the efficiency of atrazine, alachlor, and α‐cypermethrin pesticide extraction from the spiked water samples applying SPE followed by MAE. In this way, MAE served for elution of pesticides from C₁₈‐extraction disks with solvent heated by microwave energy. Various elution conditions were tested for their effects on the extraction efficiency of the SPE–MAE combined technique. Several parameters, such as elution solvent volume (mL), elution temperature (°C), and duration of elution (min), affect the extraction efficiency of the SPE–MAE coupled system and need to be optimized for the selected pesticides. In order to develop a mathematical model, 15 experiments were performed in the central composite design. The equation was then used to predict recoveries of the pesticides under specific experimental conditions. Optimization of microwave extraction was accomplished using the genetic algorithm approach. Best results were achieved using 20 mL of ethanol at 60°C. Optimal hold time was 5 min and 24 s. The SPE–MAE combination was also compared with the conventional SPE extraction technique with elution of a nonpolar or a moderately polar compound with nonpolar solvents.     

Extraction and determination of phenolic derivatives in water samples by using polyoxyethylene surfactants and liquid chromatography with photodiode array detection

Methodology based on the cloud-point phenomenon was applied to the comparative study of 3 different polyoxyethylene nonionic surfactants in order to extract and preconcentrate a group of phenolic derivatives in water samples; these phenolic compounds, which were determined by liquid chromatography with UV detection, included 11 pollutants given priority by the U.S. Environmental Protection Agency. The optimum conditions for the extraction and preconcentration of phenolic compounds were established for each surfactant. The surfactant that gave the best extraction and preconcentration of the analytes under study was polyoxyethylene 6 lauryl ether (C12E6) with detection limits of <3.5 microg/L for all the phenolic compounds tested. The method was applied to seawater and depurated wastewater samples.     

The effect of organic nitrogenous compound content and different pretreatments on agricultural lignocellulosic biomass characterization methods

Considering the diverse compounds contained in lignocellulosic biomasses, especially in agricultural biomass, and the complexity of the different chemical and physical structural connections between these compounds, appropriate analytical methods must be used to characterize these biomasses. In this study, two extraction processes and two analytical methods were used to characterize the main compounds in corn stover residue before and after different pretreatments. The results of this study suggest that pretreatment and organic nitrogenous compound content greatly affect the most common extraction processes and analytical methods used for biomass characterization. For raw corn stover biomass residue, the extraction process using neutral detergent fiber solvent removed more extractives and more organic nitrogenous compounds (18.5 and 2.4%, respectively) than the combination of extractions using water and ethanol (13.4% of extractives and 1.8% of organic nitrogenous compounds). This study also showed that the different pretreatments improve the efficiency of both extraction processes and that these processes seem to be more effective with the neutral detergent solvent extraction than the combination of extractions with water and ethanol. Organic nitrogenous compounds represent a significant proportion of agricultural biomasses; therefore, insufficient organic nitrogenous compound extraction can cause interference with different characterization methods. It was observed that, for the same analytical method and with the raw biomass, the value of insoluble lignin after the extractions with water and ethanol was higher than that obtained after the extraction with the neutral detergent solvent 16.1 and 13.2%, respectively. This can be explained by the fact that there are more organic nitrogenous compounds in the samples after the extraction with water and ethanol than in the samples after the extraction with the neutral detergent solvent. This result was also observed for the pretreated samples. These results, therefore, show that the extraction step is very important because it can remove more organic nitrogenous compounds before the main compounds are characterized (lignin, carbohydrates).     

Fast analysis of volatile organic compounds and disinfection by-products in drinking water using solid-phase microextraction-gas chromatography/time-of-flight mass spectrometry

A fast method was developed for the extraction and analysis of volatile organic compounds, including disinfection by-products (DBPs), with headspace solid-phase microextraction (HS-SPME) and gas chromatography/mass spectrometry (GC/MS) techniques. A GC/time-of-flight (TOF)-MS instrument, which had fast acquisition rates and powerful deconvolution software, was used. Under optimum conditions total runtime was 45s. Volatile organic compounds (VOCs), including purgeable A and B compounds (listed in US Environmental Protection Agency method 624), were identified in standard water samples. Extraction times were 1min for more volatile compounds and 2min for less volatile compounds. The method was applied to the analysis of water samples treated under different disinfection processes and the results were compared with those from a liquid-liquid extraction method.     

Determination of steroid sex hormones in wastewater by stir bar sorptive extraction based on poly(vinylpyridine-ethylene dimethacrylate) monolithic material and liquid chromatographic analysis

In this study, a simple and rapid method was developed for the determination of seven steroid hormones in wastewater. Sample preparation and analysis were performed by stir bar sorptive extraction (SBSE) based on poly(vinylpyridine-ethylene dimethacrylate) monolithic material (SBSEM) combined with high-performance liquid chromatography with diode array detection. To achieve the optimum extraction performance, several main parameters, including extraction and desorption time, pH value and contents of inorganic salt in the sample matrix, were investigated. Under the optimized experimental conditions, the method showed good linearity and repeatability, as well as advantages such as sensitivity, simplicity, low cost and high feasibility. The extraction performance of SBSEM to the target compounds also compared with commercial SBSE which used polydimethylsiloxane as coating. Finally, the proposed method was successfully applied to the determination of the target compounds in wastewater samples. The recoveries of spiked target compounds in real samples ranged from 48.2% to 110%.