Fluorescence optosensor using an artificial neural network for screening of polycyclic aromatic hydrocarbons

This paper presents an optosensor for screening of four polycyclic aromatic hydrocarbons: anthracene (ANT), benzo[a]pyrene (BaP), fluoranthene (FLT), and benzo[b]fluoranthene (Bbf) using a photomultiplier device with an artificial neural network as transducer. The optosensor is based on the on-line immobilization on a non-ionic resin (Amberlite XAD-4) solid support in a continuous flow. The determination was performed in 15 mM H₂PO₄⁻/HPO₄²⁻ buffer solution at pH 7 and 25% of 1,4-dioxane. Feed forward neural networks (multiplayer perceptron) have been trained to quantify the considered Polycyclic aromatic hydrocarbons (PAHs) in mixtures under optimal conditions. The optosensor proposed was also applied satisfactorily to the determination of the considered PAHs in water samples in presence of the other 12 EPA–PAHs.     

Cigarette filter as sorbent for on-line coupling of solid-phase extraction to high-performance liquid chromatography for determination of polycyclic aromatic hydrocarbons in water

An on-line solid-phase extraction (SPE) protocol using the cigarette filter as sorbent coupled with high-performance liquid chromatography (HPLC) was developed for simultaneous determination of trace naphthalene (NAPH), phenanthrene (PHEN), anthracene (ANT), fluoranthene (FLU), benzo(b)fluoranthene (BbF), benzo(k)fluoranthene (BkF), benzo(a)pyrene (BaP), and benzo(ghi)perylene (BghiP) in water samples. To on-line interface solid-phase extraction to HPLC, a preconcentration column packed with the cigarette filter was used to replace a conventional sample loop on the injector valve of the HPLC for on-line solid-phase extraction. The sample solution was loaded and the analytes were then preconcentrated onto the preconcentration column. The collected analytes were subsequently eluted with a mobile phase of methanol-water (95:5). HPLC with a photodiode array detector was used for their separation and detection. The detection limits (S/N = 3) for preconcentrating 42 mL of sample solution ranged from 0.9 to 58.6 ng L(-1) at a sample throughput of 2 samples h(-1). The enhancement factors were in the range of 409-1710. The developed method was applied to the determination of trace NAPH, PHEN, ANT, FLU, BbF, BkF, BaP and BghiP in local river water samples. The recoveries of PAHs spiked in real water samples ranged from 87 to 115%. The precisions for nine replicate measurements of a standard mixture (NAPH: 4.0 microg L(-1), PHEN: 0.40 microg L(-1), ANT: 0.40 microg L(-1), FLU: 2.0 microg L(-1), BbF: 1.6 microg L(-1), BkF: 2.0 microg L(-1), BaP: 2.0 microg L(-1), BghiP: 1.7 microg L(-1)) were in the range of 1.2-5.1%.     

Determination of polycyclic aromatic hydrocarbons in Athens atmosphere

Concentrations of total suspended particulates (TSP), benzene soluble fraction (BSF) and polycyclic aromatic hydrocarbons (PAH) have been determined in ambient air from four different sites in Athens, situated in urban, semi-industrial and industrial areas. GLC analysis has been applied for the determination of PAH, while the CGC/MS technique was used in order to confirm the obtained results. The same PAH pattern was observed for all stations. The identified PAH have been fluoranthene (FLA), pyrene (PYR), benzo(a)anthracene (BaA), chrysene (CHR), benzo(b)fluoranthene (BbF), benzo(k)fluoranthene (BkF), benzo(a)pyrene (BaP), benzo(e)pyrene (BeP) and benzo(ghi)perylene (B(ghi)P). The concentrations of individual PAH ranged from traces to 33 ng m-3 (e.g. same or lower comparing to other large cities). The higher values of PAH were found during adverse meteorological conditions.     

Solid-surface phosphorescence characterization of polycyclic aromatic hydrocarbons and selective determination of benzo(a)pyrene in water samples

This paper presents the phosphorescence characterization of polycyclic aromatic hydrocarbons (PAHs) on solid-surface for obtaining new flow-through phosphorescence optosensors for PAHs-based on-line, immobilized onto a non-ionic resin solid support coupled to a continuous flow system and the applications for the selective determination of benzo(a)pyrene (BaP). The phosphorescent characterization of 15 PAHs, described as major pollutants by the Environmental Protection Agency (EPA) (naphthalene, acenaphthylene, acenaphthene, fluorene, phenanthrene, anthracene, fluoranthene, pyrene, chrysene, benzo(a)anthracene, benzo(k)fluoranthene, benzo(b)fluoranthene, benzo(a)pyrene, indeno(1,2,3-cd)pyrene, benzo(g,h,i)perylene and dibenzo(a,h)anthracene) has been carried out. The experimental variables (heavy atom, deoxygenation and organic solvent in samples) for obtaining different possibilities for developing mono and multi-parameter PAH sensors and the conditions for PAH screening have been carefully studied and the experimental conditions to determination of BaP in presence of other PAHs in water samples have been optimized.     

Highly sensitive and selective fluorescence optosensor to detect and quantify benzo[a]pyrene in water samples

We describe here a method for detecting and quantifying the highly carcinogenic polycyclic aromatic hydrocarbon (PAH) benzo[a]pyrene (BaP) in water, based on a flow-trough optical sensor. The technique is fast (response time of 40 s) and simple and at the same time meets the standards of sensitivity and selectivity required by the European Guidelines on Water for Human Consumption. The optosensor is based on the on-line immobilization of BaP on a non-ionic resin (Amberlite XAD-4) solid support in a continuous-flow system. BaP was analyzed in a 15 mM H₂PO₄⁻/HPO₄²⁻ buffer solution with 25% (v/v) 1,4-dioxane at pH 7. Fluorescence intensity was measured at λ_ex/em=392/406 nm. The experimental conditions (reagent phase, pH, type and concentration of buffer solution and organic solvent) and flow-injection values (flow rate and injection volume) were carefully controlled. Under these conditions the optosensor was sensitive to a linear concentration range of between 3.0 and 250.0 ng l⁻¹ with a detection limit of 3.0 ng l⁻¹ and a standard deviation of 1.5% at 150 ng l⁻¹. The optosensor was applied to the quantification of BaP in drinking and waste water samples (95-105% recovery) in presence of the other 15 EPA PAHs at 1000 ng l⁻¹ concentration level. The influence of other fluorescent polycyclic aromatic hydrocarbons and potential interference from ions usually present in water was also evaluated.     

Electrochemical DNA biosensor for polycyclic aromatic hydrocarbon detection

Four DNA electrochemical biosensors using four types of DNA (calf thymus ssDNA, calf thymus dsDNA, salmon testis ssDNA and salmon testis dsDNA) were constructed using graphite screen printed electrodes. These biosensors were exploited as analytical tool to detect polycyclic aromatic hydrocarbons-DNA interactions using benzo(a)anthracene and phenantrene as model analytes, the guanine oxidation peak variation being the signal revealing the interaction between PAHs and immobilized DNA. The salmon testis ssDNA biosensor resulted as the most promising device and was further evaluated for benzo(a)anthracene, fluorene, indeno(1,2,3-cd)pyrene, anthracene, and phenanthrene in 5–40 ng mL^?1 solutions, and for benzo(a)pyrene (5–50 ng mL^?1). A concentration dependent variation of the DNA guanine oxidation peak was observed for all compounds. The effect of benzo(a)pyrene ultraviolet (UV) activation on the benzo(a)pyrene (BaP)-DNA interaction was evaluated at concentration levels of 20 and 50 ng mL^?1, and a 3.5- and 2.7-fold increases of the guanine oxidation peak was measured respectively. The salmon testis ssDNA biosensor was examined with PAHs contaminated samples of Mytilus galloprovincialis. Upon UV irradiation of three sample extracts exceeding the BaP maximum level, a positive variation of the DNA guanine oxidation was obtained. An average 2.4-fold increase of the guanine oxidation peak was detected demonstrating that the sensor can be used to detect toxic degradation products of PAHs.     

Collection and analytical characterisation of the atmospheric particulate in the city of Bari

In this paper an application of new procedures for atmospheric particulate analysis is illustrated. PM10, PAHs (benzo[a]anthracene (BaA), benzo[b]fluoranthene (BbF), benzo[j]fluoranthene (BjF), benzo[k]fluoranthene (BkF), benzo[a]pyrene (BaP), indeno[1, 2, 3-cd]pyrene (Ip), dibenzo[a, h]anthracene (DbA)) and heavy metals (Cu, Ni, Zn, Co, Mn, Cd, Fe and Pb) were investigated. PM10 determination was performed by gravimetric method, PAHs were measured by GC-MS, and heavy metals by HPIC. An air quality monitoring campaign on the territory of Bari municipality has been organised, and its results are shown.     

Use of coacervates for the on-site extraction/preservation of polycyclic aromatic hydrocarbons and benzalkonium surfactants

The suitability of coacervates for the preservation of organic pollutants after their extraction from water samples was investigated for the first time. Acid-induced sodium dodecanesulfonic acid (SDSA) micelle-based coacervates were selected for this purpose. Their capacity to preserve benzalkonium homologue (C₁₂, C₁₄ and C₁₆) surfactants (BASs) and different polycyclic aromatic hydrocarbons (PAHs) [benzo(a)pyrene (BaP), benzo(b)fluoranthene (BbF), benzo(k)fluoranthene (BkF), benzo(ghi)perylene (BghiP), benzo(a)anthracene (BaA) and indene(1,2,3-c-d)pyrene (IP)] was investigated. BASs and PAHs were efficiently extracted by the coacervate by formation of mixed aggregates and hydrophobic interactions, respectively. Their stability into the coacervate was investigated under three temperature conditions (room temperature, 4 °C and −20 °C) and two hydrochloric acid concentrations (3.75 M and 4.2 M), which was used to induce coacervation. No losses were observed during at least 3 months at the different experimental conditions tested. The increase of the temperature up to 35 °C for a month did not affect the stability of the target compounds. No influence of the water matrix (distilled, river or wastewater) on the stabilization of BASs and PAHs was observed. The high-stabilizing capacity of the coacervate for the target compounds and its low volume make easy the transport and storage of analytes.     

Resolution of benzo[a]pyrene in complex mixtures of other polycyclic aromatic hydrocarbons. Comparison of two spectrofluorimetric methods applied to water samples

Two spectrofluorimetric methods, second-derivative constant-energy synchronous luminescence (SDCESL) and constant-wavelength synchronous luminescence (CWSL) in combination with multiple linear regression (MLR), for the quantification of benzo[a]pyrene (BaP) at sub-ng mL-1 levels, in the presence of benzo[b]fluoranthene (BbFt), benzo[k]fluoranthene (BkFt), benzo[ghi]perylene (BghiP) and indeno[1,2,3-cd]pyrene (IP), were developed and compared in detail. SDCESL presents lower limits of detection and quantification than CWSL/MLR and also gives more exact and precise results for levels close to the quantification limit. For BaP, SDCESL achieved quantification limits of 0.019 ng mL-1 in river waters and 0.007 ng mL-1 in drinking waters. This work offers a sensitive, precise, accurate, rapid, simple and economic methodology for monitoring BaP in waters for public consumption, meeting all the requirements of the EC Directive 98/83/CE that fixes the maximum admissible limit for this polycyclic aromatic hydrocarbon in drinking waters at of 0.010 ng mL-1.     

A new strategy based on cholesterol-functionalized iron oxide magnetic nanoparticles for determination of polycyclic aromatic hydrocarbons by high-performance liquid chromatography with cholesterol column

This study reported for the first time the use of cholesterol-functionalized magnetic nanoparticles (Fe₃O₄@SiO₂@Chol) for the determination of polycyclic aromatic hydrocarbons (PAHs) in traditional Chinese medicine samples (TCMs) by high performance liquid chromatography (HPLC) coupled with fluorescence detection. The method was efficient, environmentally friendly, and fast. The solvent consumption of the proposed column is only half of the conventional column but with higher efficiency. Influencing factors, including sorbent amount, desorption solvent, sample volume and extraction time, were investigated in detail. Under the optimum conditions, good linearity (R² > 0.991) was obtained over the range of 5–400 ng g⁻¹, with limits of detection (LOD) 0.75, 0.50, 1.0, 0.56, 0.60, 0.84 and 0.80 ng g⁻¹ for anthracene, fluoranthene, pyrene, chrysene, benzo[a]anthracene, benzo(b)fluoranthene and benzo(k)fluoranthene, respectively.     

Multiwalled carbon nanotubes/cryogel composite, a new sorbent for determination of trace polycyclic aromatic hydrocarbons

A new cost-effective sorbent, multiwalled carbon nanotubes/poly (vinyl alcohol) cryogel composite (MWCNTs/PVA), was prepared under frozen conditions for the extraction and preconcentration of trace polycyclic aromatic hydrocarbons (PAHs) in water samples. This was followed by high performance liquid chromatography (HPLC) with fluorescence detection. The proposed method provided a high enrichment factor with an extremely high extraction efficiency (89–98%) of three spiked levels of three standard PAHs with relative standard deviations of less than 8%. The low detection limits of the method were 5, 8 and 5 ng L^{− 1} for benzo(a)anthracene, benzo(b)fluoranthene and benzo(a)pyrene, respectively. This method was successfully applied for the determination of the three PAHs in real water samples where they were found in the range of 7 to 22 ng L^{− 1}. The major advantages of MWCNTs/PVA over the commercial C₁₈ is that it can be operated at a higher loading flow rate without sorbent clogging and requires a shorter time for completion without any loss of extraction efficiency.     

Rapid simultaneous determination of four anthracene derivatives using a single non-linear variable-angle synchronous fluorescence spectrum

A rapid, simple and inexpensive spectrofluorimetric method has been developed for the simultaneous identification and quantification of anthracene (ANT), 9,10-dimethylanthracene (DIM), 2-aminoanthracene (AMI) and dibenz[ah]anthracene (DIB). A well-resolved spectrum for the mixture of these four compounds is obtained based on a single non-linear variable-angle synchronous scanning. The linear concentration ranges are 10–1000, 5–500, 50–1000 and 10–200 ng mL^–1 for ANT, DIM, AMI and DIB, respectively, at λ_ex/λ_em = 358/380, 399/408, 414/465 and 298/394 nm, respectively. The analyses are performed in cyclohexane. Recoveries of 90.0–111.0% in synthetic mixtures are obtained. The detection limits are 2.0 ng mL^–1 for DIM, 2.7 ng mL^–1 for ANT, 15.8 ng mL^–1 for AMI and 4.2 ng mL^–1 for DIB. The method has also been applied to several real water samples with satisfactory results. Received: 29 March 2000 / Revised: 30 June 2000 / Accepted: 4 July 2000     

Determination of Polycyclic Aromatic Hydrocarbons in Traditional Chinese Medicine Raw Material,Extracts, and Health Food Products

The four polycyclic aromatic hydrocarbon markers (PAH4) of benzo[a]anthracene (BaA), chrysene (Chr), benzo[b]fluoranthene (BbF), and benzo[a]pyrene (BaP) are indicators showing polycyclic aromatic hydrocarbon (PAH) contamination levels in Chinese medicine raw materials (CMRMs), extracts and health food products; Samples of herbal medicine, herbal extracts, and food supplements were extracted with n-hexane, then cleaned up sequentially on Florisil and EUPAH solid-phase extraction (SPE) columns. A gas chromatography–mass spectrometry method for the determination of four polycyclic aromatic hydrocarbon markers in Chinese medicine raw material, extracts, and health food products was established; In spiked-recovery experiments, the average recovery was about 78.6–107.6% with a precision of 2.3–10.5%. The limit of quantification (LOQ) and limit of detection (LOD) of the PAH4 markers in this method were 2.0 μg/kg and 0.7 μg/kg, respectively. When the developed method was utilized to determine PAH4 contents in 12 locally available health food products, 3 samples contained over 10.0 μg/kg BaP, and 5 samples contained over 50.0 μg/kg PAH4. The European Union (EU) limits for BaP and PAH4 are 10 and 50.0 μg/kg, respectively; therefore, more attention must be drawn to the exposure risk of BaP and PAH4 in CMRMs, their extracts, and health food products. According to the risk assessment based on the Margin of Exposure (MOE) method, it is recognized that the products mentioned in this study pose a low risk.     

气相色谱-串联质谱法同时测定卷烟滤嘴中15种多环芳烃

建立了气相色谱-串联质谱同时检测卷烟滤嘴中15种多环芳烃的方法。卷烟滤嘴用二氯甲烷振荡萃取后,经0.22μm有机相滤膜过滤,采用DB-5MS色谱柱(30 m×0.25 mm,0.25μm)进行分离,电子轰击源、正离子模式下以多反应监测模式进行检测,内标法进行定量。15种多环芳烃(苊烯、苊、芴、菲、蒽、荧蒽、芘、苯并[a]蒽、屈、苯并[b]荧蒽、苯并[k]荧蒽、苯并[a]芘、二苯并[a,h]蒽、苯并[g,h,i]苝和茚并[1,2,3-c,d]芘)的线性关系良好,相关系数(R~2)为0.991 4~0.999 9。15种多环芳烃在低、中、高3个添加水平下的平均回收率为81.6%~111.2%;除了芴在低添加水平时相对标准偏差为19.2%外,其他相对标准偏差均小于16%。15种多环芳烃的检出限为0.02~0.24 ng/滤嘴,定量限为0.04~0.80 ng/滤嘴。方法前处理简便,具有快速、准确、灵敏度高及重复性好的优点,适用于卷烟滤嘴中多环芳烃的分析。     

Use of cotton as a sorbent for on-line precolumn enrichment of polycyclic aromatic hydrocarbons in waters prior to liquid chromatography determination

Using cotton as a solid-phase extraction sorbent of the precolumn, an on-line coupled precolumn preconcentration-liquid chromatography system with fluorescence detection was developed for the determination of PAHs in aqueous samples. Four PAHs including fluorene, phenanthrene, fluoranthene and benzo[k]fluoranthene were preconcentrated by a precolumn packed with 30 mg of absorbent cotton and then separated by C₁₈ analytical column. When 100 ml of sample was enriched, the proposed procedure provided detection limits in the range of 0.5-57 ng l⁻¹. Several water samples spiked with PAHs were analyzed with recoveries in the range of 92-119% at spiking level of 100 ng l⁻¹ for fluorene, phenanthrene and fluoranthene, and 10 ng l⁻¹ for benzo[k]fluoranthene, respectively.     

Determination of polycyclic aromatic hydrocarbons (PAHs) in particulate matter collected with low volume samplers

The determination of polycyclic aromatic hydrocarbons (PAHs) contained in samples of particulate matter (PM), collected with low volume pumps, were carried out with an high sensitivity method that comes from several revisions of a previous method. The present work describes how, by using programmable temperature vaporization (PTV) and a mass selective detector with inert ionic source for the GC-MS analysis and the modifications of microwave-assisted extraction (MAE), the sensitivity of the method can be increased.The PAHs chosen for testing the method are: benzo[a]anthracene (BaA), benzo[b]fluoranthene (BbF), benzo[k]fluoranthene (BkF), benzo[a]pyrene (BaP), indeno[1,2,3-cd]pyrene (Ip) and dibenzo[a,h]anthracene (DbA). They, in fact, belong to that group of substances that are the most harmful for human health for their carcinogenicity.PAHs recoveries for spiked standard solutions at different concentrations were between 95 and 100% with relative standard deviation ranging from 1 to 3%. The revised method was validated using a 1649a urban dust standard reference material (SRM). The results obtained were in good agreement with certified values. The high sensitivity of the method allows to carry out analyses using only a half of the sampled filter (usually 47 mm diameter membranes). In this way, the other half can be used for the characterization of the other components of PM (heavy metals, organic carbon, ions, etc). The last step has been constituted by application of the optimized method on real samples collected in two cities located in Southern Italy (Bari and Taranto).     

Determination of Benzo(a)Pyrene and other Polynuclear Aromatic Hydrocarbons in Airborne Particulate Material by Ultrasonic Extraction and Reverse Phase High Pressure Liquid Chromatography

Abstract

Ultrasonic extraction of airborne particulate material on Hi-Vol filters is described. Almost all of the polar compounds are removed during the extraction by adsorption on the surface of the shredded glass fibers and controlled pore glass powder (CPG). The non-polar polynuclear aromatic hydrocarbons (PAH) in the extract are separated at room temperature by high pressure liquid chromatography (HPLC) on reverse phase Vydac using acetonitrile:water (70:30 v/v) as the chromatographic solvent. There is baseline separation of benzo(a)pyrene (BaP), benzo(k)fluoranthene (BkFt) and of benzo(e)pyrene (BeP), benzo(b)fluoranthene and perylene, the latter three present in one band. Extracts of airborne particulates show the same peaks. BaP elutes in approximately 14 minutes. Precision and accuracy measurements indicate full recovery of PAH and good extraction reproducibility. The detection limit of BaP at F 290/389 is less than 10 pg. Total analysis time is approximately 1 1/2 hr, most of which is waiting time.     

Atmospheric levels of polycyclic aromatic hydrocarbons in gas and particulate phases from Tarragona Region (NE Spain)

The atmospheric levels of polycyclic aromatic hydrocarbons (PAHs) in atmospheric samples taken at two urban sites and two sites near industrial areas of the Tarragona region (Catalonia, Spain), where one of the most important petrochemical complexes in the south of Europe is located, were determined. Gas and particulate phase of air were separately sampled and analysed. Concentrations of 16 PAHs studied ranged from 4.2 to 22.5 ng m^?3, with predominant levels of PAHs appearing in gas phase (～90% of total PAHs). In all samples, the most abundant compounds were phenanthrene, with a contribution to total PAHs between 32 and 44%, followed by naphthalene, fluorene and fluoranthene (contribution range: 10–22%). The levels of total PAHs, expressed as benzo[a]pyrene toxic equivalent factors (BaP_TEF), were lower than 0.06 ng m^?3.     

Highly sensitive and selective sensing platform based on π–π interaction between tricyclic aromatic hydrocarbons with thionine–graphene composite

We are just beginning to exploit the fascinating potential of thionine, called electrochemical probe that can selectively recognize specific polycyclic aromatic hydrocarbons (PAHs), as tools for the detection of tricyclic aromatic hydrocarbons phenanthrene (PHE) and anthracene (ANT). A novel electrochemical sensing platform by modification of electroactive thionine functionalized graphene onto glass carbon electrode (Th/GRs/GCE) surface was constructed. The immobilized thionine showed a remarkable stability, which may benefit from the π–π stacking force with graphene. Under optimum conditions, the proposed electrochemical sensor exhibited high sensitivity and low detection limit for detecting PHE and ANT. The total amount of PHE and ANT could be quantified in a wide range of 10 pM–0.1 μM with a good linearity (R² = 0.9979) and a low detection limit of 0.1 pM (S/N = 3). Compounds which possess one or two benzene rings or PAHs with more than three rings, such as benzene, naphthalene (NAP), benzo[a]pyrene (BaP) and pyrene (PYR) show little interference on the detection. Consequently, a simple and sensitive electrochemical method was proposed for the determination of PHE and ANT, which was used to determine PHE and ANT in waste water samples. The electrochemical method provides a general tool that complements the commonly used spectroscopic methods and immune method for the detection of PAHs.     

On-line and in-situ detection of polycyclic aromatic hydrocarbons (PAH) on aerosols via thermodesorption and laser-induced fluorescence spectroscopy

A fiber optical sensor system for the determination of polycyclic aromatic hydrocarbons (PAH) on aerosols by laser-induced, time-resolved fluorescence is combined with a thermodesorption device. The sensor system is based on an aerosol flow cell, which is fibre-optically coupled to a pulsed nitrogen laser for excitation and the detection system. Time-resolved fluorescence emission spectra are detected by a monochromator equipped with a photomultiplier and a fast digital storage oscilloscope. The analytical figures of merit of the thermodenuder are reported for benzo[a]pyrene, benzo[b]fluoranthene, and benzo[ghi]-perylene on ultrafine soot and NaCl aerosols. By thermodesorption of the PAH, problems due to quenching of the PAH fluorescence by the bulk aerosol material or excimer formation on the aerosol surface were avoided. For the PAH under study, the sensitivity was improved considerably and detection limits between 110 and 850 ng m^–3 were attained, while a response time of 2–3 min was achieved with the thermodenuder. A calibration for PAH on ultrafine soot and NaCl aerosols was established independent of the aerosol substrate.