Self-consistent modeling of large plastic deformation, texture and morphology evolution in semi-crystalline polymers

A self-consistent model for semi-crystalline polymers is proposed to study their constitutive behavior, texture and morphology evolution during large plastic deformation. The material is considered as an aggregate of composite inclusions, each representing a stack of crystalline lamellae with their adjacent amorphous layers. The deformation within the inclusions is volume-averaged over the phases. The interlamellar shear is modeled as an additional slip system with a slip direction depending on the inclusion's stress. Hardening of the amorphous phase due to molecular orientation and, eventually, coarse slip, is introduced via Arruda-Boyce hardening law for the corresponding plastic resistance. The morphology evolution is accounted for through the change of shape of the inclusions under the applied deformation gradient. The overall behavior is obtained via a viscoplastic tangent self-consistent scheme. The model is applied to high density polyethylene (HDPE). The stress-strain response, texture and morphology changes are simulated under different modes of straining and compared to experimental data as well as to the predictions of other models.     

Constitutive model for plastic deformation of nanocrystalline materials with shear band

A phase mixture model was used to study the plastic deformation behaviors in hardening stage of nanocrystalline materials. The material was considered as a composite of grain interior phase and grain boundary (GB) phase. The constitutive equations of the two phases were determined in term of their main deformation mechanisms. In softening stage, a shear band deformation mechanism was presented and the corresponding constitutive relation was established. Numerical simulations have shown that the predications fit well with experimental data. The investigation using the finite-element method (FEM) provided a direct insight into quantifying shear localization effect in nanocrystalline materials.     

金属材料平面应变拉伸变形局部化有限元分析

本文对于涉及韧性金属大变形中颈缩与剪切带断裂一类高度非线性变形局部化问题进行了弹塑性有限元数值模拟。采用改进的Ｊ２形变理论微分形式公式与交叉三角形四边形单元有限元网格，详细研究了应变硬化指数及初始表面不均匀特性的平面应变拉伸颈缩和剪切带形成的综合影响，给出此类问题的断裂机制图。     

A perturbation analysis of the unstable plastic flow pattern evolution in an aluminum alloy

In the tensile loading of sheet metals made from some polycrystalline aluminum alloys, a single deformation band appears inclined to the elongation axis in the early stage of deformation, and symmetric double bands are observed in the later stage. This evolution of spatial characteristics of such an unstable plastic flow pattern in a polycrystalline aluminum alloy has been analyzed by a perturbation method. A small number of slip modes are taken to describe the tensile strain. A rate-dependent constitutive equation is used for each slip mode to account for the interaction between dislocations and solute atoms in dynamic strain aging. Unconstrained and constrained models are used to impose appropriate loading conditions at the early and later deformation stages, respectively. Both plane-strain and plane-stress cases are considered. It is found out that the change of boundary conditions and material inhomogeneity during the course of plastic deformation are closely related to the evolution of spatial characteristics of shear band (the Portevin–Le Chatelier band) patterns observed in experiments.     

Crystal plasticity analysis of dislocation emission from micro voids

Slip deformation in the vicinity of a micro void in metal crystals is analyzed by a crystal plasticity technique, and the geometrically necessary dislocations, which accompany the gradient of plastic shear strain on slip systems, are evaluated. Aggregates of dislocation segments on pairs of slip systems that have the same slip directions but different slip planes exhibit a rhombus-shaped structure, and the structure is shown to be equivalent to prismatic dislocation loops of the interstitial type. Material transport and growth of voids are discussed in terms of GN dislocations.     

Multi-slip gradient formulation for modeling microstructure effects on shear bands in granular materials

This paper presents a higher order gradient multi-slip formulation to model the effect of inhomogeneous deformation in granular materials. The effects of heterogeneity and porosity anisotropy within the multi-slip formulation are taken into consideration through the modification of the mobilized friction. The mobilized friction is assumed to be a direct function of either the gradient of the porosity distribution or the fabric tensor. The formulation with two active slip planes was implemented into a finite element code and used to simulate biaxial shear tests on dry sand. The analysis quantifies most of the shear band characteristics observed by past experimentation. It is shown that the localization and shear band characteristics in granular materials are very much dependent on the initial fabric and slip system arrangement.     

Large strain plastic deformation by crystallographic slio in metals

Large strain plastic deformation of metallic materials is investigated. The rate of change of the resolved shear stress applied to a slip system in a grain is expressed as a linear function of the slip rates. For this purpose, using an elastic-plastic analysis of the inclusion problem, the Jaumann rate of change of the stress state applied to the grain, together with its total spin, are obtained as a function of its deformation rate in the rigid-plastic case. It is shown that the existing stress has a significant influence on the accommodation tensors involved in the solution.     

双相高强钢FeNiAlC的动态剪切行为及微结构机理

绝热剪切带是金属材料在高应变率载荷下常见的一种失效模式。利用霍普金森压杆装置,对双相钢Fe-24.86Ni-5.8Al-0.38C不同微结构的帽形样品施加冲击载荷,研究它的动态剪切变形行为及微结构机理。先通过对固熔处理得到的粗晶态样品进行大应变冷轧获得冷轧态样品,再使用透射电子显微镜和扫描电子显微镜表征两种样品冲击前后微结构的变化差异。结果表明,双相钢FeNiAlC拥有较优异的动态剪切性能,剪切强度达1.3 GPa,均匀剪切应变达1.5。变形前,材料由奥氏体相和马氏体相构成,马氏体体积分数约为20%。变形过程由位错滑移和孪生变形主导,但因应变速率较高致使马氏体相变被抑制。不同微结构样品内均形成绝热剪切带,带内发生动态再结晶,形成超细晶粒,平均晶粒尺寸约300 nm,且剪切带内不发生相变;冷轧态剪切带宽度的实验值（14.6 μm）与理论计算值(12.3 μm)较好吻合,而粗晶态剪切带宽度的实验值（14.6 μm）与理论计算值（30 μm）相差甚远,初步分析可能是因为粗晶态样品应变较大基本不满足完全绝热的理论条件。在变形过程中,粗晶态因塑性变形做功产生的绝热温升高达720 K,而冷轧态的只有190 K。通过实验结果与热塑模型分析,得出绝热温升不是形成绝热剪切带的唯一因素,而应考虑材料的微观结构和局部化变形等的共同影响。     

Damage in edge cracking of rolled metal slabs

Materials get damaged under shear deformations. Edge cracking is one of the most serious damage to the metal rolling industry, which is caused by the shear damage process and the evolution of anisotropy. To investigate the physics of the edge cracking process, simulations of a shear deformation for an orthotropic plastic material are performed. To perform the simulation, this paper proposes an elasto-aniso-plastic constitutive model that takes into account the evolution of the orthotropic axes by using a bases rotation formula, which is based upon the slip process in the plastic deformation. It is found through the shear simulation that the void can grow in shear deformations due to the evolution of anisotropy and that stress triaxiality in shear deformations of (induced) anisotropic metals can develop as high as in the uniaxial tension deformation of isotropic materials, which increases void volume. This echoes the same physics found through a crystal plasticity based damage model that porosity evolves due to the grain-to-grain interaction. The evolution of stress components, stress triaxiality and the direction of the orthotropic axes in shear deformations are discussed.     

动态载荷下剪切变形局部化、微结构演化与剪切断裂研究进展

总结和评述了近年来金属与合金变形局部化的形成、微结构演化与剪切断裂方面作者和相关的研究工作成果. 材料包括低碳钢, SS304不锈钢, Fe-15%Ni-15%Cr单晶, Al-Li合金,α-Ti和Ti-6Al-4V, Al/SiCp复合材料等.综述内容主要包括:采用改进的Hopkinson扭杆装置,对剪切变形局部化形成、发展和演化过程进行了实验观察与数值模拟;采用"侧剖"与"对接"等定点方法制备电子显微镜薄膜试样,对剪切带内相变与再结晶、非晶转变、旋涡结构等动态变形现象,以及与宏观动态力学行为对应的位错胞的形成、发展和坍塌等微结构特征进行了观测;提出了应变和应变率同时作为剪切带形成的两个必要条件的直接实验证据;在剪切带内发现了α'$-马氏体相变现象,以及相变产物与母体之间的晶体学关系;通过位错单滑移或交滑移等微观剪切最后发展成为宏观剪切的机制;对剪切带内再结晶结构的观测和对再结晶动力学本构关系的定量描述;对剪切带特别是``白色'腐蚀带(或相变带)的形成机制的分析和新的解释,指出 ``白色'是带内亚结构取向趋于一致,其在光学或扫描显微镜下很难辨认这些亚结构的取向差所致,并非表明剪切带内一定发生了相变;通过截断实验和实时跟踪观测发现,剪切带内微裂纹的萌生与聚合是材料承载能力骤然下降并导致最后断裂的主控因素.此外,本文对近年来在准静态和循环加载下材料的局部化形变与剪切断裂的实验结果予以简要评述,指出其微观机制与动态载荷下的截然不同, 是由位错的平面滑移所控制的,与热效应无关的等温变形.      

Dislocation pile-ups in bicrystals within continuum dislocation theory

Within continuum dislocation theory the plastic deformation of bicrystals under a mixed deformation of plane constrained uniaxial extension and shear is investigated with regard to the nucleation of dislocations and the dislocation pile-up near the phase boundaries of a model bicrystal with one active slip system within each single crystal. For plane uniaxial extension, we present a closed-form analytical solution for the evolution of the plastic distortion and of the dislocation network in the case of symmetric slip planes (i.e. for twins), which exhibits an energetic as well as a dissipative threshold for the dislocation nucleation. The general solution for non-symmetric slip systems is obtained numerically. For a combined deformation of extension and shear, we analyze the possibility of linearly superposing results obtained for both loading cases independently. All solutions presented in this paper also display the Bauschinger effect of translational work hardening and a size effect typical to problems of crystal plasticity.     

Analysis of anisotropy and plastic spin effects on localization phenomena

Summary The main objective of the paper is the investigation of the influence of the anisotrophy and plastic spin effects on criteria for adiabatic shear band localization of plastic deformation. A theory of thermoplasticity is formulated within a framework of the rate-type covariance material structure with a finite set of internal state variables. The theory takes into consideration such effects as plastic non-normality, plastic-induced anisotropy (kinematic hardening), micro-damage mechanism, thermomechanical coupling and plastic spin. The next objective of the paper is to focus attention on cooperative phenomena in presence of the plastic spin, and the discussion on the influence of synergetic effects on localization criteria. A particular constitutive law for the plastic spin is assumed. The necessary condition for a localized plastic deformation region to be formed is obtained. This condition is accomplished by the assumption that some eigenvalues of the instantaneous adiabatic acoustic tensor vanish. A procedure has been developed which allows us to discuss two separate groups of effects on the localization phenomenon along a shear band. Plastic spin, spatial covariance and kinematic hardening effects are investigated at an isothermal process in an undamaged solid. In the second case, an adiabatic process in a damaged solid is discussed when the spatial covariance terms and the plastic spin are neglected. Here the thermomechanical coupling, micro-damage mechanism and kinematic hardening effects are examined. For both cases, the criteria for adiabatic shear band localization are obtained in an exact analytical form. Particular attention is focused on the analysis of the following effects: (i) plastic non-normality; (ii) plastic spin; (iii) covariant terms; (iv) plastic strain-induced anisotropy; (v) micro-damage mechanism; (vi) thermomechanical couplings. Cooperative phenomena are considered, and synergetic effects are investigated. A discussion of the influence of the plastic spin, kinematic hardening and covariant terms on the shear band localization conditions is presented. A numerical estimation of the effects discussed is given. Received 24 April 1997; accepted for publication 23 December 1997     

Dynamics of texture evolution in face-centered cubic polycrystals

Texturing of polycrystals under slip-dominated plastic deformation is driven by reorientation velocity fields that arise from the lattice spin that accompanies restricted slip. Here, the dynamics of reorientation velocity fields are analyzed to isolate mechanisms by which textures develop and dissipate. Two tools are introduced to enable this analysis: linear stability analysis to assess behavior of equilibrium orientations, and a parametrization of lattice spins to enable analysis of fields without equilibria. This toolkit is applied to face-centered cubic (FCC) polycrystals and sheds new insight into texture development under three representative deformation modes: plane strain compression, pure shear and simple shear.     

Anti-plane shear cracks in ideally plastic crystals

Cracks in ductile single crystals are analyzed here for geometries and orientations such that two-dimensional states of anti-plane shear constitute possible deformation fields. The crystals are modelled as ideally plastic and yield according to critical resolved shear stresses on their slip systems. Restrictions on the asymptotic forms of stress and deformation fields at crack tips are established for anti-plane loading of stationary and quasistatically growing cracks, and solutions are presented for several specific orientations in f.c.c. and b.c.c. crystals. The asymptotic solutions are complemented by complete elastic-plastic solutions for stationary and growing cracks under small scale yielding, based on previous work by Rice (1967, 1984) and Freund (1979). Remarkably, the plastic zone at a stationary crack tip collapses into discrete planes of displacement and stress discontinuity emanating from the tip; plastic flow consists of concentrated shear on the displacement discontinuities. For the growing crack these same planes, if not coincident with the crack plane, constitute collapsed plastic zones in which velocity and plastic strain discontinuities occur, but across which the stresses and anti-plane displacement are fully continuous. The planes of discontinuity are in several cases coincident with crystal slip planes but it is shown that this need not be the case, e.g., for orientations in which anti-plane yielding occurs by multi-slip, or for special orientations in which the crack tip and the discontinuity planes are perpendicular to the activated slip plane.     

预延伸非晶聚合物材料各向异性变形局部化

给出一种可描述预延伸各向异性特性的背应力张量三维表达式，引入大变形弹塑性有限元驱动应力法，结合ＢＰＡ８ 链细观分子网络模型，模拟了预延伸各向异性非晶聚合物材料平面应变拉伸变形局部化力学行为．详细讨论了预延伸比（ＩｎｉｔｉａｌＤｒａｗｉｎｇＲａｔｉｏ；ＩＤＲ）和预延伸方向（ＩｎｉｔｉａｌＤｒａｗｉｎｇＤｉｒｅｃｔｉｏｎ；ＩＤＤ）对变形抗力、颈缩规律、剪切带方向以及试件中心部位链延伸比的影响．     

Analysis of dynamic shear bands in an FCC single crystal

We study plane strain dynamic thermomechanical deformations of an fcc single crystal compressed along the crystallographic direction [010] at an average strain rate of 1000 sec⁻¹. Two cases are studied; one in which the plane of deformation is parallel tothe plane (001) of the single crystal, and another one with deformation occuring in the plane (101̄) of the single crystal. In each case, the 12 slip systems are aligned symmetrically about the two centroidal axes. We assume that the elastic and plastic deformations of the crystal are symmetrical about these two axes. The crystal material is presumed to exhibit strain hardening, strain-rate hardening, and thermal softening. A simple combined isotropic-kinematic hardening expression for the critical resolved shear stress, proposed by Weng, is modified to account for the affine thermal softening of the material. When the deformation is in the plane (001) of the single crystal, four slip systems (111)[11̄0], (111̄)[11̄0], (11̄;1̄;)[110], and (11̄1)[110] are active in the sense that significant plastic deformations occur along these slip systems. However, when the plane of deformation is parallel to the plane (101̄;) of the single crystal, slip systems (11̄;1)[110], (11̄1)[011], (111)[11̄0], and (111)[01̄1] are more active than the other eight slip systems. At an average strain of 0.0108, the maximum angle of rotation of a slip system within a shear band, about an axis perpendicular to the plane of deformation, is found to be 20.3° in the former case, and 22.9° in the latter.     

AN ANALYSIS OF THE EFFECTS OF SYMMETRICAL TILT GRAIN BOUNDARIES ON THE PLASTIC DEFORMATION

A numerical investigation on the simple polycrystals containing threesymmetrical tilt grain boundaries(GBs)is carried out within the framework of crystalplasticity which precisely considers the finite deformation and finite lattice rotation aswell as elastic anisotropy.The calculated results show that the slip geometry and theredistribution of stresses arising from the anisotropy and boundary constraint play animportant role in the plastic deformation in the simple polycrystals.The stress levelalong GB is sensitive to the load level and misorientation,and the stresses along GB aredistributed nonuniformly.The GB may exhibit a softening or strengthening feature,which depends on the misorientation angle.The localized deformation bands usuallydevelop accompanying the GB plastic deformation,the impingement of the localizedband on the GB may result in another localized deformation band.The yield stresseswith different misorientation angles are favorably compared with the experimentalresults.     

A crystal plasticity model that incorporates stresses and strains due to slip gradients

This work is concerned with incorporating the kinematic and stress effects of excess dislocations in a constitutive model for the elastoplastic behavior of crystalline materials. The foundation of the model is a three term multiplicative decomposition of the deformation gradient in which the two classical terms of plastic and elastic deformation are included along with an additional term for long range strain due to the collective effects of excess dislocations. The long range strain is obtained from an assumed density of Volterra edge dislocations and is directly related to gradients in slip. A new material parameter emerges which is the size the region about a continuum point that contributes to long range strains.Using Hookean elasticity, the stress at a point is linearly related to the sum of the elastic plus the long range strain fields. However, the driving force for slip is postulated to be due only to the elastic stress so that the long range stress is a back stress in the constitutive relationship for plastic deformation. A consistent balance of the total deformation rate with the three proposed mechanisms of deformation leads to a set of differential equations that can be solved for the elastic stress, rotation and pressure which then implicitly defines the material state and equilibrium stress. Results from the simulation of a tapered tensile specimen demonstrate that the constitutive model exhibits isotropic and kinematic type hardening effects as well as changes in the pattern of plastic deformation and necking when compared to a material without slip gradient effects.     

Non-local crystal plasticity model with intrinsic SSD and GND effects

A strain gradient-dependent crystal plasticity approach is presented to model the constitutive behaviour of polycrystal FCC metals under large plastic deformation. In order to be capable of predicting scale dependence, the heterogeneous deformation-induced evolution and distribution of geometrically necessary dislocations (GNDs) are incorporated into the phenomenological continuum theory of crystal plasticity. Consequently, the resulting boundary value problem accommodates, in addition to the ordinary stress equilibrium condition, a condition which sets the additional nodal degrees of freedom, the edge and screw GND densities, proportional (in a weak sense) to the gradients of crystalline slip. Next to this direct coupling between microstructural dislocation evolutions and macroscopic gradients of plastic slip, another characteristic of the presented crystal plasticity model is the incorporation of the GND-effect, which leads to an essentially different constitutive behaviour than the statistically stored dislocation (SSD) densities. The GNDs, by their geometrical nature of locally similar signs, are expected to influence the plastic flow through a non-local back-stress measure, counteracting the resolved shear stress on the slip systems in the undeformed situation and providing a kinematic hardening contribution. Furthermore, the interactions between both SSD and GND densities are subject to the formation of slip system obstacle densities and accompanying hardening, accountable for slip resistance. As an example problem and without loss of generality, the model is applied to predict the formation of boundary layers and the accompanying size effect of a constrained strip under simple shear deformation, for symmetric double-slip conditions.     

非晶合金剪切带动力学行为研究

剪切带是一种材料塑性变形高度局域化的变形模式, 广泛存在于非晶体系的形变中, 控制着这些无序体系失稳、灾难性断裂行为.传统的非晶体系如岩石, 胶体, 玻璃和聚合物等因较差的力学性能以及过于复杂的结构而不利于剪切带的实验研究. 近几十年来, 非晶合金的出现极大丰富了剪切带的研究, 推进了对剪切带的认识. 通过大量非晶合金中剪切带的实验和理论研究, 人们发现剪切带行为具有空间不均匀性和时间不连续性的特征, 表现出复杂的动力学特征, 和自然界以及物理系统中许多复杂体系的动力学行为相似.同时, 剪切带的性质尤其是其动力学行为对非晶合金的宏观力学行为和性能有重要的影响, 对理解这类材料的微观变形机理也起着重要的作用.本文结合团队近年来在非晶合金剪切带行为方面的研究结果, 对剪切带的运动行为和物理机制进行介绍, 包剪切带间歇性运动行为、以及间歇性运动在表征其动力学性质中的作用以及物理机制, 以及剪切带的自组织临界行为、物理机制等.最后对非晶合金剪切带行为研究中亟需解决的问题进行了总结和展望.