带有增益的单微环谐振器的光速控制行为

带有损耗的光波导微环谐振器在实现光速控制时存在输出脉冲能量损耗大、脉冲形状畸变严重等问题。基于带有增益和带有损耗的微环谐振器的传输特性之间的对称性,计算分析了单微环谐振器的透射率、群折射率和群速度色散等特性,分析了增益和损耗对微环谐振器输出特性影响的机制。计算了带有增益的微环谐振器的光速控制行为,并与带有损耗的微环谐振器进行对比。结果显示,带有增益的微环谐振器输出脉冲不分裂且有较大的输出强度。脉冲延迟量和超前量比损耗系统大,可用于光速控制,克服了微环带有损耗时产生的光强损耗和脉冲畸变。     

多辊轧机冷轧技术在靶材料制备中的应用

 叙述了多辊轧机轧制金属薄膜原理,以Ti膜制备为例,借助多辊轧机冷轧技术进行1.5 μm厚钛薄带的制备工艺研究。对薄膜的特性测试结果表明：工作辊的表面粗糙度对于轧制薄膜的表面粗糙度的影响很大,降低工作辊表面的粗糙度可以得到粗糙度为25.2 nm的金属薄膜。     

星载高分辨率超光谱成像仪分光方式的选择

从多个方面分析了棱镜和光栅色散分光的优缺点,分析结果表明棱镜更适于星载高分辨率超光谱成像仪的分光。在透过率方面,棱镜光谱仪透过率高达95.24％(VNIR),而光栅的衍射效率仅为60%~70%。在杂散光方面,棱镜光谱仪的杂散光可达10－4,而光栅的杂散光为10－2。在0.4 －2.5 范围,棱镜光谱仪相对光栅光谱仪有优越性。在色散线性方面,光栅光谱仪基本线性,棱镜光谱仪的短波非线性问题可通过复合棱镜进行补偿。可靠性方面,棱镜光谱仪较光栅光谱仪有优势;在光谱带宽和成本方面,棱镜光谱仪与光栅光谱仪基本接近。     

叠片法测量“闪光二号”加速器的高功率离子束能谱

给出了利用叠片法测量“闪光二号”加速器高功率离子束能谱的基本原理及初步实验结果. 采用Ziegler的拟合公式编制程序计算了不同能量质子和碳离子穿过不同厚度Mylar膜后的能 量损失情况.在偏压法拉第筒阵列各个法拉第筒的准直孔前分别覆盖0—6μm厚的Mylar膜， 根据不同膜厚对应的信号衰减情况(叠片法)，得到了高功率离子束的离子能谱，离子的最高 能量>440keV，平均能量约为270keV，能量为200—300keV之间的离子数目最多，碳离子数和 90keV以下的质子所占总离子数的组分不多于32％.所测量离子能谱和离子数目随时间的分布 关系与二极管的电压和电流符合也较好.还将叠片法的测量结果与利用磁谱仪和采用飞行时 间法等的测量结果进行了比较，三种方法所得的测量结果基本一致. 关键词： 高功率离子束 离子能谱 法拉第筒 叠片法 能量损失     

多辊轧机冷轧技术在靶材料制备中的应用

叙述了多辊轧机轧制金属薄膜原理,以Ti膜制备为例,借助多辊轧机冷轧技术进行1.5 μm厚钛薄带的制备工艺研究。对薄膜的特性测试结果表明：工作辊的表面粗糙度对于轧制薄膜的表面粗糙度的影响很大,降低工作辊表面的粗糙度可以得到粗糙度为25.2 nm的金属薄膜。     

采用铜铝复合管的翅片管换热器性能试验研究

针对铜铝复合管(ACC管)在空调用翅片管换热器中替代铜管应用进行了试验研究。分别对Ф7.94mm型管的全铜管、过冷段铜铝复合管、全铜铝复合管三种换热器进行了性能比较和成本分析。研究结果表明,在风速和风量不变的情况下,过冷段铜铝复合管换热器能力为8634.22W,高于全铜铝复合管的换热器的8389.36W,低于全铜管换热器的8989.07W。制冷剂侧能力测试中,过冷段铜铝复合管换热器平均值为8.885kW,与全铜铝复合管换热器平均值8.775kW相比高1.24%,与全铜管换热器平均值9.101kW相比低2.37%,与能力测试结果基本一致。与原换热器铜管相比,在相同条件下,铜铝复合管可以降低管材成本29.5%。综上所述,过冷段采用铜铝复合管的换热器能够取代铜管换热器应用在空调中,在不影响其换热性能的基础上,降低成本效果明显。     

Dynamical scaling of the structure factor of some non-Euclidean systems

Predictions of nonlinear theories on dynamics of new phase formation have been examined for the hydration of calcium silicates with light water and heavy water. In the case of hydration with light water, reasonable agreement has been observed with dynamical scaling hypothesis with a new measure of the characteristic length. The characteristic length does not follow a power law relation with time. Hydrating mass is found to be mass fractal throughout hydration, with mass fractal dimension increasing with time. But, in the case of hydration with heavy water, no agreement has been observed with the scaling hypothesis. Hydrating mass undergoes transition from mass fractal to surface fractal and finally again to mass fractal. The qualitative features of the kinetics of hydration, as measured in small-angle scattering experiments, are strikingly different for hydration with light water and heavy water.     

Spectroscopic Study of Laser-Induced Cu Plasma With and Without the Confinement of a Substrate

Optical emission spectroscopic studies have been carried out on the laser-induced copper plasma generated in the process of laser-driven flyer (with the substrate confinement). The copper plasma in the air (without the substrate confinement) has also been researched in order to know the differences between the plasma with the confinement and that without the confinement. The plasma is assumed to be in local thermodynamic equilibrium. The result shows that, under the same laser fluence, the plasma exists a longer time with the confinement. The time-resolved electron temperature and density with the confinement are higher than those with no confinement. The substrate deposited with Cu foil plays an important role in enhancing the temperature and the density of the plasma. The electron temperature and density with confinement increase with a larger scope as the laser fluence increases than that with no confinement.      

Studies on modified power law inflation

In this study, we evaluate power law inflation (PLI) with a monomial potential and obtain a novel exact solution. It is well known that the conventional PLI with an exponential potential is inconsistent with the Planck data. Unlike the standard PLI, the present model does not encounter the graceful exit problem, and the results agree fairly well with recent observations. In our analysis, we calculate the spectral index and the tensor-to-scalar ratio, both of which agree very well with recent observational data and are comparable with those of other modified inflationary models. The employed technique reveals that the large cosmological constant decreases with the expansion of the universe in the case of the PLI. The coupling of the inflaton with gravitation is the primary factor in this technique. The basic assumption here is that the two metric tensors in the gravitational and inflaton parts correspond to different conformal frames, which contradicts with the conventional PLI, where the inflaton is directly coupled with the background metric tensor. This fact has direct applications to different dark energy models and the assisted quintessence theory.     

精确的量子化条件和不变量

提出并证明了一维量子系统和三维球对称量子系统的一个精确的量子化条件.在此精确量子化条件中, 除了通常的Nπ项外, 还有一积分项, 称为修正项. 发现该修正项正是在超对称量子力学中所谓的有形状不变势的量子系统的一个不变量，它不依赖于波函数的节点数.对这些系统, 可用基态能级和波函数确定此不变量的值, 从而由精确的量子化条件容易算出全部束缚态的能级. 计算得到能级的正确性又反过来验证了在有形状不变势的量子系统中此修正项确实是不变量.计算的有形状不变势的量子系统, 包括一维的有限方势阱、Morse势及其变形、R 关键词： 量子化条件 超对称量子力学 形状不变势 不变量     

Rosochatius Deformed Soliton Hierarchy with Self-Consistent Sources

Integrable Rosochatius deformations of finite-dimensional integrable systems are generalized to the soliton hierarchy with self-consistent sources. The integrable Rosochatius deformations of the Kaup-Newell hierarchy with self-consistent sources, of the TD hierarchy with self-consistent sources, and of the Jaulent-Miodek hierarchy with self-consistent sources, together with their Lax representations are presented.     

L型脉冲形成网络的仿真与实验研究北大核心CSCD

研究了L型连接结构对脉冲形成网络输出波形的影响。采用有限积分法,对L型连接结构的脉冲形成网络进行三维建模和仿真,并将其与直线型连接结构的脉冲形成网络仿真结果进行比较。结果表明:L型结构的脉冲形成网络前沿与直线型结构基本一致,约为40ns,半高宽为168ns,比直线型小7ns,平顶处较直线型结构有所波动,表现为平顶后段幅度升高。通过对两种连接结构的脉冲形成网络进行高压实验,验证了仿真结果。在脉冲功率驱动源结构紧凑化的工程应用中,L型连接结构的输出波形能基本满足要求。     

L型脉冲形成网络的仿真与实验研究

研究了L型连接结构对脉冲形成网络输出波形的影响。采用有限积分法,对L型连接结构的脉冲形成网络进行三维建模和仿真,并将其与直线型连接结构的脉冲形成网络仿真结果进行比较。结果表明：L型结构的脉冲形成网络前沿与直线型结构基本一致,约为40 ns,半高宽为168 ns,比直线型小7 ns,平顶处较直线型结构有所波动,表现为平顶后段幅度升高。通过对两种连接结构的脉冲形成网络进行高压实验,验证了仿真结果。在脉冲功率驱动源结构紧凑化的工程应用中,L型连接结构的输出波形能基本满足要求。     

Comparison of the solutions from a novel variational method with numerical results for the study of beam propagation in a Kerr medium with nonlinear absorption

We present results from a novel variational method for the study of beam propagation in a Kerr medium with nonlinear absorption. This new method combines the variational method and a nonlinear absorption equation and gives a concise expression for the combination. The results obtained with this method show good quantitative agreement with numerical solutions obtained with the finite-difference method. It is shown that the variational method takes much less time than a numerical simulation with the finite-difference method for analysis of beam propagation in a thick medium with nonlinear absorption and nonlinear refraction. The new method makes detailed analysis of beam propagation in a Kerr medium with nonlinear absorption very simple and fast.     

Pelvic phased array coil: image quality assessment for spin-echo MR imaging.

The NMR phased array coil (PA) provides improved signal-to-noise ratio (SNR) over that available with the body coil. We evaluated image quality obtained with a pelvic PA compared to that obtained with the body coil for spin-echo imaging. Thirty-three women undergoing clinical pelvic MRI were imaged with the body coil followed by imaging with the PA with the same field-of-view (FOV) in 11 patients, and with a small FOV in 23 patients. Image quality was assessed independently by two radiologists. In individual cases there was significant improvement in image quality with the PA, however the expected marked improvement in image quality was not consistently found. Two factors which may limit image quality are increased motion artifact and nonuniformity of signal with distance from the coils. Significant improvements in image quality may occur with improved techniques to decrease motion artifact.     

The structure of vocal sounds produced with the mouth closed or with the mouth open in treefrogs

Frogs and toads mostly call with their mouths shut, unlike many other vertebrates. Sound is generated when air crosses the larynx, but there is no direct airflow to the external environment and radiation occurs at the skin. This study directly compares the acoustic output obtained from euthanized frogs with the mouth open against the output obtained with the mouth closed during activation of the larynx by airflow. With the mouth closed, the vocal sac was inflated and the acoustic energy was concentrated in the same harmonics as in the advertisement call, whereas with the mouth open, energy was spread in a wide range of harmonics. The acoustic output at the dominant frequency was more intense with the mouth closed than with the mouth open. More sound was radiated through the vocal sac and head than through the rest of the body. The spectral differences between open and closed mouth treatments matched the differences observed between natural advertisement calls, produced with the mouth closed, and distress calls, produced with the mouth open. By calling with the mouth closed, treefrogs can potentially produce advertisement calls with the energy concentrated in a narrower frequency range than with the mouth open.     

Photonic analog-to-digital conversion using multiple comparators and Mach-Zehnder modulators with identical half-wave voltages

A novel photonic analog-to-digital conversion scheme using Mach-Zehnder modulators (MZMs) with identical half-wave voltages and multiple comparators with improved bit resolution is proposed and demonstrated. Compared with the scheme using MZMs with geometrically scaled half-wave voltages, the proposed scheme has the advantage of using MZMs with identical half-wave voltages which simplify significantly the implementation. The bit resolution is improved based on the use of multiple comparators in each MZM channel, with the digital coding realized based on the symmetrical number system theory. A proof-of-concept experiment is implemented. An analog-to-digital converter with a 4-bit resolution using two MZMs and nine comparators is demonstrated.     

石英玻璃微球吸收光谱上的结构共振

通过CO2激光器熔融不同直径的熔锥光纤以得到相应直径的石英玻璃微球,利用此微球和熔锥光纤,构造了球微腔耦合系统。实验中利用光腰直径为3.1μm的熔锥光纤与直径为143.1μm的石英玻璃微球进行耦合,通过最大分辨力为1pm的可调谐半导体激光器对该耦合系统进行光谱扫描,发现石英玻璃微球的吸收光谱中出现分立的结构共振峰。利用光学微球腔理论讨论了石英玻璃微球吸收光谱中的结构共振,并用米氏散射理论公式对一阶TE模共振峰的位置以及它们的间隔进行了计算,共振峰位置实验结果与理论结果的误差仅为0.03%,表明实验与计算结果相符。     

Thickness shear mode quartz crystal resonators with optimized elliptical electrodes

Quartz crystal resonators (QCRs) with circular electrodes have been widely used for various liquid and gas sensing applications. In this work,quartz crystal resonators with elliptical electrodes were studied and tested for liquid property measurement. Mindlin’s theory was used to optimize the dimension and geometry of the electrodes and a 5-MHz QCR with minimum series resistance and without any spurious modes was obtained. A series of AT-cut QCRs with elliptical electrodes of different sizes were fabricated and their sensing performances were compared to devices with circular electrodes. The experimental result shows that the device with elliptical electrodes can obtain lower resonance impedance and a higher Q factor,which results in a better loading capability. Even though the sensitivities of devices with elliptical and circular electrodes are found to be similar,the sensor with elliptical electrodes has much higher resolution due to a better frequency stability. The study indicates that the performance of QCRs with elliptical electrodes is superior to that of traditional QCRs with circular electrodes.     

Thermal Oxidation of a Carbon Condensate Formed in High-Frequency Carbon and Carbon–Nickel Plasma Flow

We have reported on the comparative characteristics of thermal oxidation of a carbon condensate prepared by high-frequency arc evaporation of graphite rods and a rod with a hollow center filled with nickel powder. In the latter case, along with different forms of nanodisperse carbon, nickel particles with nickel core–carbon shell structures are formed. It has been found that the processes of the thermal oxidation of carbon condensates with and without nickel differ significantly. Nickel particles with the carbon shell exhibit catalytic properties with respect to the oxidation of nanosized carbon structures. A noticeable difference between the temperatures of the end of the oxidation process for various carbon nanoparticles and nickel particles with the carbon shell has been established. The study is aimed at investigations of the effect of nickel nanoparticles on the dynamics of carbon condensate oxidation upon heating in the argon–oxygen flow.