CuO－ZnO基CO_2／H_2合成甲醇催化剂的反应活性中心

应用ＸＰＳ，ＸＡＥＳ和紫外漫反射光谱法研究了ＣｕＯ－ＺｎＯ／氧化物上ＣＯ２／Ｈ２合成甲醇的反应活性中心．ＣｕＯ－ＺｎＯ／氧化物催化剂上的反应活性中心是存在于ＣｕＯ－ＺｎＯ固溶体中的Ｃｕ－Ｚｎ－Ｏ（＂□＂为氧空位），活性中心的Ｃｕ价态为Ｃｕ－和Ｃｕ０．反应活性中心在ＣｕＯＺｎＯ－ＺｒＯ２催化剂上比在其它ＣｕＯ－ＺｎＯ／氧化物催化剂如ＣｕＯ－ＺｎＯ，ＣｕＯ－ＺｎＯ－ＭｇＯ，ＣｕＯＺｎＯ－Ａｌ２Ｏ３和ＣｕＯ－ＺｎＯ－ｒ２Ｏ３上更加稳定．     

制备方法对超细Cu／ZnO／Al2O3催化剂上CO2＋H2合成甲醇的影响

制备方法对超细Ｃｕ／ＺｎＯ／Ａｌ_２Ｏ_３催化剂上ＣＯ_２＋Ｈ_２合成甲醇的影响张玉龙，王欢，邓景发（复旦大学化学系，上海，２００４３３）关键词超细粒子，合成甲醇，Ｃｕ／ＺｎＯ／Ａｌ_２Ｏ_３催化剂，ＣＯ_２＋Ｈ_２ＣＯ２＋Ｈ２合成甲醇是目前的热门课题［１～...     

甲烷部分氧化制合成气Ⅳ．镍铜催化剂的反应性能及影响因素的考察

对镍铜甲烷部分氧化催化剂的制备化学研究表明，在Ａｌ２Ｏ３、ＳｉＯ２、ＭｇＯ、ＴｉＯ２、Ｙ型分子筛等载体中，具有较好氢溢流功能的Ａｌ２Ｏ３所担载的镍铜催化剂，有最佳的反应性能，载体的产物溢流功能对反应中合成气的生成是有利的．对于ＮｉＯ－ＣｕＯ－Ａｌ２Ｏ３催化剂，组分Ｃｕ的最佳含量是Ｃｕ／Ａｌ＝０．２／４（原子比），Ｎｉ／Ａｌ（原子比）在１／４－１．５／４范围内催化剂均保持最佳的反应性能，此时，甲烷转化率为９８．１％，对ＣＯ、Ｈ２的选择性分别达９７％、１００％．制备方法对催化性能影响的结果显示，以（ＮＨ４）２ＣＯ３为沉淀剂的共沉淀法，是制备ＮｉＯ－ＣｕＯ－Ａｌ２Ｏ３催化剂的最佳方法．ＮｉＯ－ＣｕＯ－Ａｌ２Ｏ３催化剂的甲烷部分氧化性能在４００－５００℃间有一突跃，并在７００℃时达到最佳值；过高的反应气空速对ＣＯ、Ｈ２的选择性是不利的     

二氧化碳加氢合成甲醇铜基催化剂表面组成的研究

本文分别采用ＸＲＤ、ＥＳＲ、ＸＰＳ和ＸＡＥＳ等技术对于二氧化碳加氢低压合成甲醇用ＣｕＯ，ＣｕＯ－ＺｎＯ，ＣｕＯ－ＺｎＯ－Ａｌ＿２Ｏ＿３，ＣｕＯ－ＺｎＯ－ＺｒＯ＿２催化剂在不同条件下表面Ｃｕ、Ｚｎ、Ａｌ、Ｚｒ的存在价态进行了深入分析。实验发现催化剂在还原前Ｃｕ以Ｃｕ￣２＋存在，在还原后和反应状态下以Ｃｕ￣０存在；Ｚｎ在还原后和反应状态下有部分被还原为Ｚｎ￣（２－δ）（０＜δ＜２），Ｚｒ和Ａｌ仍保持其还原前价态。催化剂的表面化学组成为：Ｃｕ￣０／Ｚｎ（２－δ）￣＋／Ｚｒ￣４＋／Ａｌ￣３＋／Ｏ￣２－。     

氧化锆对铜基甲醇合成催化剂的促进作用(英文)

采用离子掺杂价态补偿原理,在Ｃｕ－Ｚｎ－Ａｌ甲醇合成催化剂中添加适量氧化锆助剂研制Ｃｕ－Ｚｎ－Ａｌ－Ｚｒ催化剂的特性。实验结果表明,最佳反应温度为２３０℃,比Ｃｕ－Ｚｎ－Ａｌ约低１０℃。采用ＸＲＤ、ＵＶＤＲ、ＦＴＩＲ、ＴＰＤ和ＴＰＲ等谱学方法对２种催化剂进行表征显示,铜基催化剂的活性位可能是“Ｃｕ０－Ｃｕ＋－Ｏ－Ｚｎ２／Ａ２Ｏ３－ＺｒＯ２”,工作态Ｃｕ－Ｚｎ－Ａｌ－Ｚｒ催化剂表面上Ｃｕ／Ｃｕ０的比值、价态稳定性和对ＣＯ的吸附量均大于Ｃｕ－Ｚｎ－Ａｌ,这与该催化剂具有较好的低温活性和较高的热稳定性密切相关。     

甲烷部分氧化制合成气

对镍铜甲烷部分氧化催化剂的制备化学研究表明，在Ａｌ２Ｏ３、ＳｉＯ２、ｍｇＯ、ＴｉＯ２、Ｙ型分子筛等载体中，具有较好氢溢流功能的Ａｌ２Ｏ３所担载的镍铜催化剂，有最佳的反应性能、载体的产物溢物功能对反应中合成气的生成是有利的，对ＮｉＯ－ＣｕＯ－Ａｌ２Ｏ３催化剂，组分Ｃｕ的最佳含量是Ｃｕ／Ａｌ＝０．２／４（原子比），Ｎｉ／Ａｌ（原子比）在１／４－１．５／４范围内催化剂均保持最佳的反应性能，此时，甲烷转化     

Cu/ZnO/Al2O3/ZrO2催化剂上乙醇脱氢合成乙酸乙酯Ⅰ.催化反应性能及机理

研究了经ＺｒＯ２改性的Ｃｕ／ＺｎＯ／Ａｌ２Ｏ的催化性能，考察了操作条件，ＺｒＯ２含量及不同原料的影响，发现经共沉淀法制备了Ｃｕ／ＺｎＯ／Ａｌ２Ｏ３／ＺｒＯ２具有最佳的反应活性及选择性以９５％乙醇为原料，在２６５℃，ＷＨＳＶ１．５ｈ＾－１，乙醇转化率为６９．０％，乙酸乙酯选择性为７０．２％，使用无水乙醇为原料要好地９５％乙醇，使用乙醛或醇醛混合原料，亦有乙酸乙酯生成，乙醇在此催化剂上的反应机理为乙醇     

Cu／ZnO／Al_2O_3／ZrO_2催化剂上乙醇脱氢合成乙酸乙酯Ⅰ．催化反应性能及机理

研究了经ＺｒＯ２改性的Ｃｕ／ＺｎＯ／Ａｌ２Ｏ３的催化性能，考察了操作条件、ＺｒＯ２含量及不同原料的影响．发现经共沉淀法制备的Ｃｕ／ＺｎＯ／Ａｌ２Ｏ３／ＺｒＯ２具有最佳的反应活性及选择性．以９５％乙醇为原料，在２６５℃，ＷＨＳＶ１．５ｈ－１时，乙醇转化率为６９．０％，乙酸乙酯选择性为７０．２％．使用无水乙醇为原料要好于９５％乙醇，使用乙醛或醇醛混合原料，亦有乙酸乙酯生成．乙醇在此催化剂上的反应机理为乙醇先在Ｃｕ上脱氢为乙醛，然后乙醛在酸碱双中心上发生Ｃａｎｎｉｚａｒｒｏ反应生成乙酸乙酯．还讨论了ＺｒＯ２的作用及催化剂活性降低的原因     

（四甲基二硅撑）双（3－三甲硅基环戊二烯基）－四羰基二铁的反应性

标题化合物（Ｍｅ_２ＳｉＳｉＭｅ_２）［η￣５－（３－Ｍｅ_３ＳｉＣ_５Ｈ_３）Ｆｅ（ＣＯ）_２］_２／（μ－ＣＯ）_２（Ａ）分子中的Ｆｅ－Ｆｅ键被钠汞齐还原断裂，生成相应的双铁负离子，分别与ＭｅＣＯＣｌ、ＰｈＣＯＣｌ、ＰｈＣＨ_２Ｃｌ、ＣｌＣＨ_２ＣＯＯＣ_２Ｈ_５和Ｐｈ_３ＳｎＣｌ进行亲核取代反应，生成在铁原子上引入相应取代基的产物（Ｍｅ_２ＳｉＳｉＭｅ_２）［η￣５－（３－Ｍｅ_３ＳｉＣ_５Ｈ_３）Ｆｅ（ＣＯ）_２Ｒ］_２（Ｒ：ＭｅＣＯ（１），ＰｈＣＯ（２），ＰｈＣＨ_２（３），ＣＨ_２ＣＯＯＣ_２Ｈ_５（４），Ｐｈ_３Ｓｎ（５），Ｉ（６））。Ａ在氯仿中与碘反应，得到Ｆｅ－Ｆｅ断裂的双铁碘化物，但在苯中与过量碘反应，则得到Ｆｅ－Ｉ－Ｆｅ桥联的离子型化合物（Ｍｅ_２ＳｉＳｉＭｅ_２）［η￣５－（３－Ｍｅ_３ＳｉＣ_５Ｈ_３）Ｆｅ（ＣＯ）_２］_２Ｉ·Ｉ（７）。化合物６的晶体和分子结构经Ｘ射线衍射测定，６属单斜晶系，Ｐ２１／ｃ空间群，ａ＝１．７２１７（４）ｎｍ，ｂ＝０．７７５３（２）ｎｍ，Ｃ＝１．３６２９（７）ｎｍ，β＝１０３．８０（３）°，Ｖ＝１．７６７（２）ｎｍ３，Ｚ＝４，Ｄｃ＝１．６２９９·ｃｍ－１，最终偏差因子Ｒ＝０．０５４。     

在铜基催化剂上由CO加氢合成低碳混合醇反应速率控制步骤探讨

本文应用“原位”发射红外光谱技术，在２８０℃，０．５ＭＰａ反应条件下，对于Ｃｕ／ＺｎＯ／Ａｌ２Ｏ３催化剂 ＣＯ＋Ｈ２ＣＯ＋Ｈ２＋ＣＯ２反应体系的反应过程进行了动态跟踪结果表明，ＣＯ｜Ｈ２反应体系中，ＣＯ插入表面－烷氧基的金属－碳键可能是生成碳二以上醇的反应速控步骤。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.