Synthesis,characterization, and molecular modeling studies of novel polyurethanes based on 2,2′‐[ethane‐1,2‐diylbis(nitrilomethylylidene)]diphenol and 2,2′‐[hexane‐1,6‐diylbis(nitrilomethylylidene)] diphenol hard segments

Novel polyurethanes (PUs) based on 2,2′‐[ethane‐1,2‐diylbis(nitrilomethylylidene)]diphenol and 2,2′‐[hexane‐1,6‐diylbis(nitrilomethylylidene)]diphenol as hard segments containing four aromatic diisocyanates (4,4′‐diphenylmethane diisocyanate, toluene 2,4‐diisocyanate, isophorone diisocyanate, and hexamethylene diisocyanate) have been prepared. Fourier transform infrared, UV spectrophotometry, fluorescence spectroscopy, ¹H NMR and ¹³C NMR spectroscopy, thermogravimetric analysis, and differential thermal analysis have been used to determine the structural characterization and thermal properties of the segmented PUs. All the PUs contain domains of both semicrystalline and amorphous structures, as indicated by X‐ray diffraction. The acoustic properties have been calculated with the group contribution method. Molecular dynamics simulations have been performed on all the PUs to estimate the cohesive energy density and solubility parameter values, which compare well with the values calculated with the group contribution method. Furthermore, the simulation protocols have been applied to the PUs to produce X‐ray diffraction plots to determine the phase morphology of the PUs. The surface properties of the PUs have been estimated from the simulation protocols. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 6032–6046, 2006     

Photophysical and viscometric properties of naphthalene-labeled acrylamide/N,N-dimethyl maleimido propyl ammonium propane sulfonate copolymer

 The synthesis, viscometric, and fluorescence properties of a water-soluble zwitterionic sulfobetaine copolymer, poly(ADMMAPS)/NA, are reported. When fluorescent hydrophobes (naphthyl group) are incorporated into the zwitterionic copolymer, the photophysical response may effectively probe solution behavior on the microscopic level. Experimental results indicate that I _E/I _M steadily increases with increases in polymer concentration. I _E/I _M in aqueous solution is greater than that in aqueous potassium chloride solution. Dynamic light scattering (QELS) measurements show that hydrodynamic diameters of the naphthalene-labeled zwitterionic sulfobetaine copolymer increase with an increasing salt concentration. Viscosity studies reveal that the polymer coil expanded as more salt is added. In fluorescence quenching study, the reduction in the quenching efficiency of Tl⁺ with salt addition can arise from enhanced compartmentalization of naphthalene labels as added electrolyte enhances intrapolymer micellization. The intrapolymer micelle is easily formed, indicating that the thallium ion has difficulty reacting with bound naphthalenes located in the polymer coil. The naphthalene-labeled zwitterionic sulfobetaine copolymer is depicted as a compacted polymer coil conformation in deionized water because of intra-and inter-associations. Consequently, salt addition breaks up the associations and enhances the intrapolymer micellization. The microscopic and macroscopic behaviors of zwitterionic sulfobetaine copolymer differ a lot from those of the corresponding cationic copolymer. Received: 4 February 1997 Accepted: 1 May 1997     

Liquid crystalline properties of unsegmented and segmented polyurethanes synthesised from high aspect ratio mesogenic diols

A series of novel tetrad high aspect ratio mesogenic diol monomers 4-{[4-(n-hydroxyalkoxy)-phenylimino]-methyl}-benzoic acid 4-{[4-(n-hydroxyalkoxy)-phenylimino]-methyl}-phenyl ester were prepared with varying alkoxy spacer length (n=2,4,6,8,10) by reacting 4-formylbenzoic acid 4-formylphenyl ester and 4-(n-hydroxyalkoxy) anilines. Two series of thermotropic main chain liquid crystalline unsegmented polyurethanes (PUs) were obtained by the polyaddition of the mesogenic diols with hexamethylene diisocyanate (HMDI) and methylene bis(cyclohexylisocyanate) (H₁₂MDI) in dimethylformamide respectively. The effect of the incorporation of a third component namely polyol on the liquid crystalline properties of the polyurethanes was also studied. Linear segmented PUs were synthesised by a two-step block copolymerisation method. The PUs synthesised were based on six spacer mesogenic diol chain extender, soft segments poly(tetramethylene oxide)glycol (PTMG) (M_n= 650,1000,2000) and polycaprolactone diol (PCL) (M_n=530,1250,2000) of varying molecular weights and different diisocyanates including HMDI, H₁₂MDI and methylene bis(phenylene isocyanate) (MDI). Structural elucidation was carried out by elemental analysis, fourier transform infra red (FT-IR), nuclear magnetic resonance (¹H NMR and ¹³C NMR) spectroscopy. Inherent viscosity of the unsegmented polymers measured in methanesulphonic acid at 26°C was in the range of 0.13 - 0.65 dL/g while the molecular weights and molecular weight distribution of the segmented polyruethanes was determined using gel permeation chromatography (GPC). Mesomorphic properties were studied by differential scanning calorimetry (DSC) and hot stage polarising optical microscopy and the thermal stability was determined by thermogravimetric(TG)analysis. The monomeric diols and the polyurethanes exhibited nematic texture and good mesophase stability. It was observed that the partial replacement of the mesogenic diol by the polyol of varying molecular weights influenced the phase transitions and the occurrence of mesophase textures. The phase transition temperatures of the investigated polyurethanes showed dependence on the chain length of the soft segment and on the content of the mesogen moiety. A higher content of mesogenic moiety was needed to obtain liquid crystalline property when the soft segment length was increased as observed in the case of PTMG. Grained and threaded textures were observed depending on the molecular weight of the soft segment, the mesogen content and the diisocyanate. The stress-strain analyses showed that the polymers bused on high molecular weight PTMG soft segment have elastomeric property while the PCL based PUs displayed no elastomeric property.     

Novel long chain unsaturated diisocyanate from fatty acid: Synthesis,characterization, and application in bio‐based polyurethane

A novel long chain linear unsaturated terminal diisocyanate, 1,16‐diisocyanatohexadec‐8‐ene (HDEDI) was synthesized from oleic acid via Curtius rearrangement. Its chemical structure was identified by FTIR, ¹H NMR, ¹³C NMR, and HRMS. This diisocyanate was used as a starting material for the preparation of entirely bio‐based polyurethanes (PUs) by reacting it with canola diol and canola polyol, respectively. The physical properties and crystalline structure of the PUs prepared from this diisocyanate were compared to their counterparts prepared from similar fatty acid‐derived diisocyanate, 1,7‐heptamethylene diisocyanate (HPMDI). The HDEDI based PUs demonstrated various different properties compared to those of HPMDI based PUs. For example, HDEDI based PUs exhibited a triclinic crystal form; whereas HPMDI based PUs exhibited a hexagonal crystal lattice. In addition, canola polyol‐HDEDI PU demonstrated a higher tensile strength at break than that of canola polyol‐HPMDI, attributed to the higher degree of hydrogen bonding associated with the former sample. Nevertheless, lower Young's modulus and higher elongation in canola polyol‐HDEDI PU were obtained because of the flexibility of the long chain introduced by the HDEDI diisocyanate. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 3302–3310, 2010     

Quantitative IR characterization of urea groups in waterborne polyurethanes

The purpose of this study is to propose a correlation between IR spectra and the urea fraction of waterborne polyurethanes (PUs) to investigate the side reaction, that is, isocyanate–water reaction, during polymerization. This method is based on the decomposition of the spectrum in amide I range, that is, 1600–1800 cm^?1, where the bands of interest overlap. Several individual bands present in this region were resolved by employing Fourier self‐deconvolution (FSD) and Gaussian curve‐fitting techniques, and the intensity ratio of urethane's C?O to urea's C?O was determined. To realize some quantitative measurements, a calibration curve was established with some polyurethane‐urea samples, characterized by ¹H NMR, which were used as standards. The concentration ratios of urethane groups to urea groups were determined from ¹H NMR. A good correlation was evidenced between IR and ¹H NMR measurements. Moreover, waterborne PUs were prepared by miniemulsion polymerization of IPDI with diols. From quantitative IR analysis, it was shown that a vinylic monomer, as a solvent of polyaddition, restrained the isocyanate–water reaction, and this side reaction was influenced by the hydrophilicity of the vinylic monomers. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 2433–2444, 2008     

Polyisobutylene‐based polyurethanes. IX. synthesis,characterization, and properties of polyisobutylene‐based poly(urethane‐ureas)

Polyisobutylene (PIB)‐based polyurethanes (PUs) exhibit unparalleled hydrolytic‐oxidative‐biologic stability and are melt processible, however, their mechanical (strength) properties are modest mainly due to insufficient H bonds. We posited and demonstrate that the ultimate properties of PIB‐PUs are enhanced, while their melt processibility is maintained, by the judicious introduction of urea linkages, i.e., strong bifurcated H bonds, in the chain. The incorporation of bifurcated H bonds in PIB‐PUs was achieved by using the conventional butane diol chain extender (CE) in combination with controlled amounts of amino alcohol as co‐chain extender (co‐CE). Polyurethanes containing both urethane and urea linkages are polyurethane‐ureas (PUU). Specifically, PIB‐PUUs prepared with PIB‐diol/MDI together with 80/20 mole % butane diol/amino butanol exhibited ～30 MPa tensile strength, ～550% elongation, ～80 Shore A hardness, and ～137 °C flow temperature. Other amino alcohols, i.e., amino ethanol, ‐propanol, and ‐hexanol, were less effective co‐CEs. ¹H‐NMR and FT‐IR spectroscopies indicate the presence of bifurcated H bonds in PIB‐PUUs prepared with CE/co‐CE combinations. Characterization by differential scanning calorimetry, thermogravimetric analysis, dynamic mechanical thermal analysis, and creep experiments also suggest bifurcated H bonds in PIB‐PUU. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 2361–2369     

Thermal properties of poly(urethane-ester-siloxane)s based on hyperbranched polyester

Novel polyurethanes (PUs) were synthesized using hydroxy-terminated hyperbranched polyester (BH-20) and 4,4′-methylenediphenyl diisocyanate (MDI) as hard segments and hydroxy-terminated ethylene oxide-poly(dimethylsiloxane)-ethylene oxide triblock copolymer (PDMS-EO) as soft segment, with soft segment content ranging from 30 to 60 wt %. The PUs were synthesized by two-step solution polymerization method. The influence of the soft segment content on the structure, swelling behavior and thermal properties of PUs was investigated. According to the results obtained by swelling measurements, the increase of the hard segment content resulted in the increase of the crosslinking density of synthesized samples. DSC results showed that the glass transition temperatures increase from 36 to 65°C with increasing hard segment content. It was demonstrated using thermogravimetric analysis (TGA) that thermal stability of investigated PUs increases with increase of the soft PDMS-EO content. This was concluded from the temperatures corresponding to the 10 wt % loss, which represents the beginning of thermal degradation of samples.     

Investigations on monotropic liquid crystalline polyurethanes based on biphenylol

2,2′-Azobis-[2-cyano-(4-ethylphenol)] (ABCP) was prepared from parahydroxyacetophenone, using hydrazine sulfate and sodium cyanide. Biphenylol ester of ABCP, 2,2′-azobis-[2-p-biphenyloxy-(4-ethylphenol)] (BECP) was synthesized via the acid route. Combined liquid crystalline polyurethanes (CLCPUs) were synthesized from 1,6-diisocyanatohexane (HDI) and BECP in dimethylformamide (DMF) at 110°C under nitrogen atmosphere. The effect of partial replacement of BECP by 4,4′-dihydroxy biphenyl (DHBP) on liquid crystalline (LC) properties was studied. The polymers were characterized by proton and ¹³C NMR, FTIR, and UV spectroscopy. Elemental analysis were done for determining the percentage content of C, H, and N and the molecular weights of the polymers were determined by gel permeation chromatography (GPC). Thermogravimetric investigations (TGA) of the polyurethanes (PUs) were performed to study the decomposition. The LC nature of the PUs was confirmed by differential scanning calorimetry (DSC) and X-ray diffraction (XRD). Cross-polarized optical microscopy studies demonstrated the existence of two distinct crystalline morphologies, a spherulitic morphology with high mole ratio of DHBP and a thread-like crystalline morphology with that of BECP. All the PUs synthesized showed a LC nature with a wide temperature range. Partial replacement of BECP by DHBP changed the mesomorphic nature, transition temperature, and temperature range of the mesophase. © 1995 John Wiley & Sons, Inc.     

Synthesis, characterization and flocculation performance of zwitterionic copolymer of acrylamide and 4-vinylpyridine propylsulfobetaine

A novel zwitterionic polyacrylamide AMVPPS copolymer containing sulfobetaine groups was synthesized by copolymerizing acrylamide (AM) and 4-vinylpyridine propylsulfobetaine (4-VPPS) in 0.5 mol/L NaCl solution with potassium persulfate (K₂S₂O₈) and sodium bisulfite (NaHSO₃) as initiator. The structure and composition of AMVPPS copolymer were characterized by FT-IR spectroscopy, ¹H NMR and elemental analyses. Thermal stability and solution properties of AMVPPS copolymer were studied by thermogravimetry analysis (TGA) and viscometry. Anti-polyelectrolyte behavior was observed and was found to be enhanced with increasing 4-VPPS content in copolymer. The flocculation performance for 2.5 g/L kaolin suspension and 2.5 g/L hematite suspension was evaluated by transmittance measurement and phase contrast microscopy. The effects of 4-VPPS content in the copolymer, intrinsic viscosity and the added salt on the flocculation performance were investigated. It was found that AMVPPS copolymer was a good flocculant for both anionic kaolin and cationic hematite suspensions and the flocculation performance of copolymer was much better than that of pure polyacrylamide (PAM). A very wide range of the optimum flocculation concentration, named as “flocculation window”, was found for both suspensions. These flocculation characteristics were mainly dependent on the charge neutralization, the intragroup conformation transition from water to NaCl solution and then the interchain bridging of the zwitterionic AMVPPS copolymer.     

Preparation and characterization of polyurethane electrical insulating coatings derived from novel soybean oil‐based polyol

As a viable alternative to the petrochemical polyols in polyurethanes (PUs), a new soybean oil‐based polyol (PSBO) with high functionality of hydroxyl groups and built‐in (preformed) urethane bonds was introduced. At first, a facile and improved method was developed for the transformation of epoxidized soybean oil (ESBO) to carbonated soybean oil (CSBO). Then ring‐opening reaction of carbonated oil with ethanolamine (ETA) led to the polyol. After characterization by conventional spectroscopic and analytical methods, PSBO was used for the formulation of novel one‐pack PU electroinsulating wire enamels. Tunable mechanical, thermal, and electrical properties for the final PUs were achieved by replacing 10 wt% of PSBO with poly(propylene glycol) (PPG) at different number average molecular weights of 725, 1000, 2000, 4000. Investigation of the results showed that these soy‐based PUs offer excellent thermal and electrical insulating properties. Copyright © 2009 John Wiley & Sons, Ltd.     

Flame retardation of polyurethanes by means of 1,4-bis[(dialkoxyphosphinyl)hydroxymethyl]benzene

New phosphorus-containing homopolyurethanes were synthesized by reacting various diisocyanates such as tolylene diisocyanate, methylenebis(4-phenylisocyanate) and hexamethylene-1,6-diisocyanate with 1,4-bis[(dialkoxyphosphinyl)hydroxymethyl]benzene (BDAB). In addition, copolyurethanes containing approximately 3% phosphorus were prepared by copolymerization of these diisocyanates with an equimolar amount of BDAB—hydroquinone mixture. BDAB was less reactive towards diisocyanates than hydroquinone due to the electron-withdrawing inductive effect of the phosphinyl groups. The polymers synthesized were characterized by inherent viscosity measurements as well as by proton nuclear magnetic resonance (¹H-NMR) and infrared (IR) spectroscopy. The spectroscopic examination of polymers did not provide evidence for crosslinking by allophanate groups. Differential thermal analysis (DTA) studies of polymers revealed that the incorporation of BDAB in polyurethanes altered their thermal decomposition mode by increasing the exothermicity due to pyrolysis. Thermogravimetric analysis (TGA) of polymers showed that the phosphorus-containing homopolyurethanes and copolyurethanes were thermally less stable than the corresponding common polyurethanes but afforded higher char yields. Determination of the limiting oxygen index (LOI) values showed that the phosphorus-containing copolyurethanes exhibited a higher fire resistance than that of common polyurethanes.     

Synthesis and proliferative activity of a new derivative of the lupan pentacyclic triterpenoids, <Emphasis Type="Italic">viz.</Emphasis>, the sulfobetaine based on betulin with a 4-(dimethylammonio)butane-1-sulfonate moiety

A new zwitterionic derivative of the lupan pentacyclic triterpenoid series, viz., the sulfobetaine with a 4-(dimethylammonio)butane-1-sulfonate moiety, was synthesized by quaternization of betulin 28-(2-dimethylaminoacetate) with 1,4-butane sultone. The sulfobetaine was found to possess a dose-dependent proliferative effect toward human embrionic kidney cells HEK293 and human T-lymphocytes. Betulin chosen as a comparison compound demonstrated an effect against cells of both the tumor (HepG2, Jurkat) and the normal origin (human HEK293 and T-lymphocytes) which differ from that of the sulfobetaine, inhibiting their proliferation. The new sulfobetaine can prove to be a promising basis for the development of reparative and immunostimulating agents.     

Synthesis and Characterization of Comb-like Methoxy Polyethylene Glycol-grafted Polyurethanes via ‘Click’ Chemistry

In this study, a series of comb-like methoxy polyethylene glycol (MPEG) functionalized polyurethanes (PUs) (PU–g–MPEG) were successfully prepared via ‘click’ chemistry and polyaddition reaction. The copper catalyzed Huisgen 1,3-dipolar cycloaddition was firstly carried out between 3,5-bis(hydroxymethyl)-1-propargyloxybenzene (PBM) and methoxy polyethylene glycol azide (MPEG–N₃) to obtain MPEGylated diol PBM (MPEG–PBM). Then, the comb-like PUs having MPEG located on the backbones (PU–g–MPEG) were synthesized through the polyaddition of MPEGylated diol PBM and hexamethylene diisocyanate (HDI). Fourier transform infrared (FTIR), ¹H NMR spectroscopy, size exclusion chromatography (SEC), and thermo gravimetric analyses (TGA) were used to characterize these synthesized MPEG-functionalized comb-like PUs (PU–g–MPEG). Compared with PU without MPEG grafts, PU–g–MPEG show a better wettability.     

Sulfobetaine zwitterionomers based on n‐butyl acrylate and 2‐ethoxyethyl acrylate: Physical properties

New materials with potential applications for adhesives and coatings, based on copolymers containing zwitterionic pendent groups, were investigated. n‐Butyl acrylate and 2‐ethoxyethyl acrylate were copolymerized with a series of five zwitterionic sulfobetaine monomers (SBMs). The structures of the SBMs were varied systematically in terms of (1) intercharge spacing in the zwitterionic moiety and (2) substituent bulkiness at the quaternary ammonium functionality. The effect of varying the sulfobetaine content and structure in the copolymers was investigated, with an emphasis on ion aggregation behavior and physical properties, with dynamic mechanical analysis. The zwitterionomers exhibited the expected biphasic morphology, with the appearance of an ion‐rich glass‐transition temperature. An increase in the storage modulus was observed with increasing SBM content in the rubbery and terminal regions, suggesting an increased degree of ionic crosslinking in the rubbery region and decreased chain mobility in the flow region. Intercharge spacing variation in the sulfobetaine moiety did not have a significant effect on the modulus–temperature curves, contrary to our expectations. Increases in the modulus were much less pronounced for the bulkier SBMs than for the other monomers, possibly because of hindered aggregation of the sulfobetaine moieties. Likewise, matrix polarity had a greater influence on the physical properties of these materials than intercharge separation in the SBMs. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 2303–2312, 2002     

Characterization of Polyurethanes from Vegetable Oils by TG/DTG,DMA and FT-IR

Summary: Given the demand for renewable resources by industries and the promising potential of vegetable oils for this purpose, the current study aims to evaluate the properties of polyurethanes (PUs) obtained from linseed (Linum usitatissimun L.) oil (PULO) and passion fruit (Passiflora edulis Sims f. flavicarpa Degener) oil (PUPFO), by thermogravimetry (TG), derivative thermogravimetry (DTG), dynamic mechanical analysis (DMA) and Fourier transform infrared (FT-IR). The results showed that PULO is more thermally stable than PUPFO, suggesting that the first presents more urethane linkages. The DMA analysis showed that both prepared PUs have uneven porosity, causing the loss of the elastic plateau. It was found as well that PUPFO exhibits a higher value of glass transition temperature (T_g), signifying that it seems to be more crosslinked than PULO. The analysis by FT-IR showed that the curing reaction of PUs was successful.     

GRAFTING OF SULFOBETAINE ONTO A POLYURETHANE SURFACE TO IMPROVE BLOOD COMPATIBILITY

On the molecular level, it is believed that polymers containing zwitterionic structures should be compatible withblood. In this work polyurethane films were grafted with sulfobetaine by a three-step procedure. In the first step, the films'surfaces were treated with hexamethylene diisocyanate (HDI) in toluene at 50℃ in the presence of di-n-butyl tin dilaurate(DBTDL) as a catalyst. The extent of the reaction was monitored by ATR-IR spectra; a maximum number of free NCOgroups was obtained after a reaction time of 90 min. In the second step, the hydroxyl groups of N,N-dimethylethylethanolamine (DMEA) were allowed to react in toluene with NCO groups bound on the surface. In the thirdstep, sulfobetaines were formed on the surface through the ring-opening reaction between tertiary amine of DMEA and 1,3-propanesultone (PS). The surfaces of the films were characterized by ATR-IR and XPS showing that the grafted surfaceswere composed of sulfobetaine. The results of the contact angle measurement show that the surface was strongly hydrophilic.The platelet adhesion test demonstrated that the films grafted with sulfobetaine have excellent blood compatibility.     

Study of phase separation in polyurethane using paramagnetic labels. Effect of soft segment molecular weight,structure, and thermal history

The morphology of segmented polyurethane (PU) elastomers was studied by means of ESR at various temperatures ranging from 100K-450K. The PU's were based on 4,4'-diphenylmethane diisocyanate (MDI), poly (oxytetramethylene) glycols (PTMO) and hydroxyl-terminated random compolymers of tetrahydrofuran and 3-methyl-tetrahydrofuran (THF/Me-THF). Purified 1,4-butanediol (BD) was used as a chain extender. The nitroxide probe, 4-hydroxy-2-2',6-6'-tetramethylpiperidine-1-oxyl (TEMPOL), was used to label the polyurethanes by reaction with an NCO group of MDI. Analysis of the electron spin resonance (ESR) spectra suggested that the label situates at heterogeneous sites, which means that a two-phase domain is present. The morphologies at 300K and 400K were compared. It was found from ESR spectra that polyurethanes made from soft segments having higher MW exhibited greater phase separation at 300K than their corresponding elastomers made from lower MW soft segments. However, at 400K the more isotropic ESR spectra for the PUs containing higher MW soft segments suggested that the PUs were more mobile than their analogs having lower MW soft segments. The introduction of 3-methyl side groups decreased the phase mixing at 400K due to steric hindrance.     

Efficacy of clay content and microstructure of curing agents on the structure–property relationship of new‐generation polyurethane nanocomposites

The physicomechanical properties of new polyurethanes (PUs) derived from toluene diisocyanate, poly(propylene glycol), and cured by third‐generation hyperbranched polyester polyol (HB3), trimethylolpropane (TMP), or glycerol and their nanocomposites have been investigated. An apparent microphase‐segregated morphology of PU nanocomposites cured by HB3 has been observed by transmission electron microscopy and atomic force microscopy. Morphological studies reveal regions of mostly exfoliated and some intercalated morphology in the case of the nanocomposites, which have been further ascertained by X‐ray diffraction analysis. The HB3‐cured PU nanocomposite containing 8 wt% of modified montmorillonite (Cloisite 30B) clay shows approximately 140% increase in tensile strength along with improvement in thermal and dynamic mechanical properties in comparison with the control hyperbranched PU. It has also been found from Fourier transform infrared spectroscopy analysis that the extent of tethering reactions between the polymer chains carrying residual –NCO groups and the reactive hydroxyl (?OH) groups of HB3 is significant, and the nanofiller has been found to preferentially react with the –NCO group of the prepolymer. Furthermore, the properties of HB3‐cured PU have been compared with the glycerol and TMP‐cured PUs and their nanocomposites. The physicomechanical and thermal properties for nanocomposites of HB3‐cured PUs are superior to those of the conventionally cured PUs. Copyright © 2011 John Wiley & Sons, Ltd.     

Preparation of zwitterionic sulfobetaine end‐functionalized poly(ethylene glycol)‐b‐poly(caprolactone) diblock copolymers and examination of their thermogelling properties

To investigate thermogelling behavior, in this study, we prepared a methoxy poly(ethylene glycol)‐b‐poly(ε‐caprolactone) diblock copolymer (MPC) with varying hydrophobic poly(ε‐caprolactone) (PCL) lengths and an MPC featuring a zwitterionic sulfobetaine (MPC‐ZW) at the chain end of the PCL segment. The terminal zwitterionic sulfobetaine was stoichiometrically modified to the terminal MPC diblock copolymer. The introduction of the zwitterionic end group lowered the crystallization enthalpies of the PCL block segments and increased the solubility of the diblock copolymer. The MPC and MPC‐ZW copolymers thus obtained formed translucent emulsions at room temperature when prepared as 20 wt %. When the temperature was increased above room temperature, MPC and MPC‐ZW exhibited a sol‐to‐gel phase transition. The phase transition and the gelation time of MPC and MPC‐ZW were affected by the length of the hydrophobic segments and the zwitterionic end group. Furthermore, introducing a zwitterionic end group into the PCL segment altered the onset temperature of gelation. Thus, we conclude that zwitterionic end groups introduced into PCL segments of distinct lengths could serve as key determinants in the thermogelling behavior of copolymers. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 2185–2191     

Polyurethanes with separately tunable biodegradation behavior and mechanical properties for tissue engineering

Two series (random and block) poly(glycolide‐co‐ε‐caprolactone) macrodiols with various glycolide to ε‐caprolactone ratios (50/50 and 30/70, R‐PG50C, R‐PG30C, B‐PG50C, and B‐PG30C) were synthesized. Next, segmented polyurethanes (PUs) were synthesized based on the synthesized macrodiols, 1,6‐hexamethylene diisocyanate and 1,4‐butanediol (PU‐R30, PU‐R50, PU‐B30, and PU‐B50). Effect of glycolide (G) and ε‐caprolactone (C) monomers arrangement (random or block) on the PUs properties were investigated via FTIR, ¹H NMR, DSC, TGA, DMA, SEM, and mechanical tests. All PUs illustrated T_g (−33°C to −48°C) and T_m (102°C to 139°C) corresponding to the soft and the hard segments, respectively. Polymers based on block macrodiols also showed T_m related to the soft segments. While PUs underwent a two‐step thermal degradation, the PUs based on block macrodiols indicated higher degradation temperature. Dynamic mechanical analysis results evidenced development of a well‐defined microphase separated structure in PU‐R30. Contact angle (about 70°‐80°) and water uptake (around 20% after 24 hours) of the PU films are close to those suitable for tissue engineering materials. The PU based on R‐PG30C (PU‐R30) exhibited the highest tensile strength (2.87 MPa) followed by PU‐B50 and PU‐R50. Over a 63‐day in vitro degradation study in phosphate buffered saline, the PUs showed variable weight loss (up to 40%) depending on their soft segments composition and arrangement. Also, the PUs showed no cytotoxicity. Thus, these PUs with tunable biodegradation rate and mechanical properties are suitable candidates for tissue engineering.