Thermal runaway reaction evaluation of two by-products mixed with cumene hydroperoxide in the oxidation tower

Oxygen (O₂) or air is widely used to produce cumene hydroperoxide (CHP) in the cumene oxidation tower. The aim of this study was applied to analyze thermal hazard of two by-products including alpha-methylstyrene (AMS) and acetophenone (AP) in a CHP oxidation tower. Differential scanning calorimetry (DSC) and thermogravimetry (TG) were operated to evaluate thermal runaway reaction of CHP mixed with AMS and AP. Exothermic onset temperature (T ₀), maximum temperature (T _max), activation energy (E _a), etc., that were employed to prevent and protect thermal runaway reaction and explosion in the manufacturing process and storage area. In view of proactive loss prevention, the inherently safer handling procedure and storage situation should be maintained in the chemical industries. The T ₀ of 30 mass% CHP was determined to be 105 °C by DSC. Therefore, the T ₀ of 30 mass% CHP mixed with AMS was determined to be 60–70 °C by DSC. The exothermic reaction of CHP/AP and CHP/AMS by DSC under N₂ reaction gas is thermal decomposition of oxygen–oxygen bond (–O–O–) because of the anaerobic reaction.     

Thermal hazard evaluation of tert-butyl hydroperoxide mixed with four acids using calorimetric approaches

Possessing thermal instability inherently, organic peroxides have caused many severe accidents in chemical industries all over the world. tert-Butyl hydroperoxide (TBHP) is usually used as initiator or oxidant because of its strong oxidizing ability in the chemical process. In this study, the thermal hazard analysis of TBHP mixed with various acids was investigated. Differential scanning calorimetry (DSC) and vent sizing package 2 were used to figure out the thermal runaway behaviors of TBHP. Thermokinetic parameters, such as exothermic onset temperature (T ₀), maximum temperature (T _max), and enthalpy (ΔH), were obtained from thermal curves. In addition, the activation energy (E _a) and rate constant (k) were calculated by the Arrhenius equation. Therefore, the T ₀ was determined to be 91.6 °C for exothermic reaction using DSC under 4 °C min^?1 of heating rate. The E _a for exothermic reaction was calculated to be 92.38 kJ mol^?1 by DSC in this study. As far as loss prevention is concerned, thermokinetic parameters are crucial to the relevant processes in the chemical industries, particularly under process upsets.     

Explosion evaluation and safety storage analyses of cumene hydroperoxide using various calorimeters

Plenty of thermal explosions and runaway reactions of cumene hydroperoxide (CHP) were described from 1981 to 2010 in Taiwan. Therefore, a thermal explosion accident of CHP in oxidation tower in 2010 in Taiwan was investigated because of piping breakage. In general, high concentration of CHP for thermal analysis using the calorimeter is dangerous. Therefore, a simulation method and a kinetic parameter were used to simulate thermal hazard of high concentrations of CHP only by the researcher. This study was applied to evaluate thermal hazard and to analyze storage parameters of 80 and 88 mass% CHP using three calorimeters for the oxidation tower, transportation, and 50-gallon drum. Differential scanning calorimetry (DSC) (a non-isothermal calorimeter), thermal activity monitor III (TAM III) (an isothermal calorimeter), and vent sizing package 2 (VSP2) (an adiabatic calorimeter) were employed to detect the exothermic behavior and runaway reaction model of 80 and 88 mass% CHP. Exothermic onset temperature (T ₀), heat of decomposition (ΔH _d), maximum temperature (T _max), time to maximum rate under isothermal condition (TMR_iso) (as an emergency response time), maximum pressure (P _max), maximum of self-heating rate ((dT/dt)_max), maximum of pressure rise rate ((dP/dt)_max), half-life time (t _1/2), reaction order (n), activation energy (E _a), frequency factor (A), etc., of 80 and 88 mass% CHP were applied to prevent thermal explosion and runaway reaction accident and to calculate the critical temperature (T _c). Experimental results displayed that the n of 80 and 88 mass% CHP was determined to be 0.5 and the E _a of 80 and 88 mass% CHP were evaluated to be 132 and 134 kJ mol^?1, respectively.     

Thermokinetic parameters analysis for 1,1-bis-(tert-butylperoxy)-3,3,5-trimethylcyclohexane at isothermal conditions for safety assessment

The rapid development of the petrochemical industry of Taiwan over the past four decades has resulted in a booming economy in Taiwan that drives derived industries to develop progressively. However, it has also caused many runaway reaction accidents, such as toxic gas release, fire, and explosion. It is crucial to eliminate those potential hazard factors which can induce consequent runaway reaction accidents during the life span of the manufacturing process. In response to this crucial issue, we performed a thermokinetic parameter analysis for 1,1-bis-(tert-butylperoxy)-3,3,5-trimethylcyclohexane at isothermal conditions to conduct a thermal safety assessment of chemical materials. The five isothermal temperatures, 90, 100, 110, 120, 130, and 140 °C, measured by DSC, were adopted in this study to calculate process safety parameters, including TMR_ad, T _NR, and SADT, which can be employed in process safety parameters for the manufacturing process. A novel, green kinetic approach accompanied with non-isothermal DSC results is used to derive thermokinetic parameters in safety protocol in this study.     

Thermal properties and kinetics of new-generation posterior bulk fill composite cured light-emitting diodes

In this study, the thermal behavior in terms of glass transition (T _g), degradation, and thermal stability of four commercial new-generation posterior bulk fill composites (Surefill SDR, Dentsply; Quixfill, Dentsply; Xtrabase, Voco; and Xtrafill, Voco) activated by light-emitting diodes (LEDs) was analyzed by thermogravimetric analysis (TG), differential scanning calorimetry (DSC), and dynamic mechanical analysis (DMA). The activation energies (E _a) for the decomposition of the dental resins were calculated based on the Kissinger and Doyle kinetic models from the peaks of the endothermic curves obtained when the specimens were heated at four different temperatures (5, 10, 15, and 20 °C min^?1) during DSC. The results show that the Xtrabase composite displayed the highest T _g (120 °C at a 5 °C min^?1 heating rate) and E _a (157.64 kJ mol^?1) values associated with thermal degradation from the main chain of the polymer.     

Thermal and mechanical properties of epoxy resin toughened with epoxidized soybean oil

A series of new modified epoxy resin (EP) cured products were prepared from epoxidized soybean oil and commercial epoxy resin, with methyl nadic anhydride as curing agent and 1-methylimidazole as promoting agent. The thermal properties of the resins were characterized by DMA and TG; DSC was used to determine the curing process. Fourier transform infrared spectroscopy was utilized to investigate their molecular structures and scanning electron microscopy was used to observe the micro morphology of their impact fracture surfaces. Tensile and impact testing was employed to characterize the mechanical properties of the cured products. The combination of commercial EP with 20 wt% ESO resulted in a bioresin with the optimum set of properties: 130.5 °C T _g, 396.9 °C T _50 %, 74.89 MPa tensile strength, and 48.86 kJ m^?2 impact resistance.     

Synthesis,characterization, and thermal study of solid-state alkaline earth metal mandelates,except beryllium and radium

Characterization, thermal stability, and thermal decomposition of alkaline earth metal mandelates, M(C₆H₅CH(OH)CO₂)₂, (M = Mg(II), Ca(II), Sr(II), and Ba(II)), were investigated employing simultaneous thermogravimetry and differential thermal analysis or differential scanning calorimetry, (TG–DTA or TG–DSC), infrared spectroscopy (FTIR), complexometry, and TG–DSC coupled to FTIR. All the compounds were obtained in the anhydrous state and the thermal decomposition occurs in three steps. The final residue up to 585 °C (Mg), 720 °C (Ca), and 945 °C (Sr) is the respective oxide MgO, CaO, and SrO. For the barium compound the final residue up to 580 °C is BaCO₃, which is stable until 950 °C and above this temperature the TG curve shows the beginning of the thermal decomposition of the barium carbonate. The results also provide information concerning the thermal behavior and identification of gaseous products evolved during the thermal decomposition of these compounds.     

Preparation and thermal reliability of <Emphasis Type="Italic">N</Emphasis>-butyl stearate/methyl palmitate composite phase change material

In this study, a series of binary mixtures of N-butyl stearate (nBS) and methyl palmitate (MP) were used to produce a novel composite phase change material (CPCM) for potential application in the eastern China, and their thermal properties were investigated by differential scanning calorimetry (DSC). The results of DSC indicated that the mixture consisting of 10 mass% nBS and 90 mass% MP is optimum as the CPCM in terms of the phase change temperature ranges (T _f = 19.74–5.59 °C; T _m = 18.34–33.80 °C) and latent heats (ΔH _f = 176.8 J g^?1; ΔH _m = 189.3 J g^?1). On the other hand, the thermal reliability and chemical stability of the CPCM after 120, 180, 240, 300, 360 and 500 accelerated thermal cycling tests were studied by DSC and fourier transform infrared (FTIR) analysis. The results demonstrated that the CPCM had good thermal reliability and chemical stability.     

Study of thermal behaviour of some edible mushrooms

This paper is aimed to analyse the thermal behaviour in air of edible mushrooms through nonisothermal (TG, DTG, DTA) and calorimetric (Berthelot calorimeter) methods. The studied mushrooms were Pleurotus ostreatus spontaneously grown and from culture and Agaricus bisporus from culture, currently used in alimentation but insufficiently investigated from this point of view. The analysis of TG–DTG–DTA curves has indicated that the degradation mechanism is complex and characteristic to every species and major differences between the cap and the stipe of investigated mushrooms have not been recorded. These species are thermally stable in the range of 30–160 °C. The thermal stability in terms of initial degradation temperature (T _i °C) and the temperature corresponding to the conversion grade (T _α=0.03 °C) indicate that the stipe has a thermal stability close to the cap one and that the cultivated mushrooms are more thermally stable than those spontaneously grown. The obtained results concerning the combustion of the sample using Berthelot calorimeter are in accordance with the TG–DTG–DTA analysis. The residue obtained is a measure of the mineral content and is quantitatively close.     

Effects of various fire-extinguishing reagents for thermal hazard of triacetone triperoxide (TATP) by DSC/TG

Acetone, hydrogen peroxide (H₂O₂), and sulfuric acid (H₂SO₄) are easily to produce triacetone triperoxide (TATP), which is an organic peroxide and a hazardous material. The aim of this study was to analyze the thermal hazard of various fire-extinguishing reagents mixed with TATP. Various functions of fire-extinguishing reagents may have different extent of reactions with TATP. Differential scanning calorimetry (DSC) and thermogravimetric analyzer (TG) were used to detect the thermal hazard and to evaluate the effect of fire-extinguishing reagents mixed with TATP under fire condition. TATP decomposed rapidly and final decomposition was calculated before 200 °C. Therefore, heat of decomposition (ΔH _d) of TATP was evaluated to be 2,500 J g^?1 by DSC under 2 °C min^?1 of heating rate. H₂O₂, acetone, and H₂SO₄ should not be mixed in a wastewater drum. TATP decomposed at 50 °C by DSC using O₂ of reaction gas that is an exothermic reaction and can decompose a large amount of heat. Therefore, TATP was applied to assess thermal pyrolysis by DSC employing N₂ of reaction gas that can analyze an endothermic reaction. Mass loss percentage of TATP was evaluated to be 100 % when the ambient temperature exceeds 110 °C by TG using O₂ or N₂ of reaction gas.     

Temperature-dependent AC electrical conductivity,thermal stability and different DC conductivity modelling of novel poly(vinyl cinnamate)/zinc oxide nanocomposites

Thermal analysis on organically modified Ca²⁺-montmorillonite (OMON) and its source materials—octadecylamine (ODA) and Ca²⁺-montmorillonite (Ca²⁺-Mon)—was studied using thermally stimulated current (TSC) technique. The appearance of ρ _MON peak with the T _max = 75 °C shows the ability of the developed TSC system to demonstrate the relaxation effects of dehydration in Ca²⁺-Mon. It appeared within the temperature range of DSC endothermic peak (30–100 °C) where the T _mMON = 58 °C. Segmental motions of ODA chains and structural disruptions in the modifier agent compound produced TSC α _ODA, ρ _ODA and ρ _1ODA peaks that are comparable to thermal transition and endothermic peaks in DSC profile (T _gODA, T _m1ODA and T _m2ODA). The effect of localized motion in ODA chains as revealed by the TSC β_OMON peak (T _max = ?23 °C), however, is absent in the DSC profile of OMON. It shows TSC technique has high sensitivity in detecting various relaxation behaviors at molecular level. More evidences are demonstrated by the ρ _OMON (T _max = 86 °C) and ρ _1OMON (T _max = 105 °C) peak originated from the ODA chains structures. These peaks also confirm the intercalation of the modifier cations inside the Ca²⁺-Mon gallery.     

Thermal hazard evaluation of tert-butyl peroxide using non-isothermal and adiabatic calorimetric approaches

Tert-butyl peroxide (TBPO), is a typical organic peroxides (OPs),which is widely applied as initiator in poly-glycidyl methacrylate (PGMA) reaction, and is employed to provide a free-radical in frontal polymerization, and which has also caused many thermal runaway reactions and explosions worldwide. To find an unknown and insufficient hazard information for an energetic material, differential scanning calorimetry (DSC) and vent sizing package 2 (VSP2) were employed to detect the fundamental thermokinetic parameters involving the exothermic onset temperature (T ₀), heat of decomposition (??H _d), temperature rise rate (dT · dt ^?1), time to maximum rate under adiabatic situation (TMR_ad), pressure rise rate (dP · dt ^?1), and maximum pressure (P _max), etc. The T ₀ was calculated to be 130?°C using DSC and VSP2. Activation energy (E _a) of TBPO was evaluated to be 136?kJ?mol^?1 by VSP2. In view of the loss prevention, calorimetric applications and model evaluation to integrate thermal hazard development are adequate means for inherently safer design.     

DSC measurements of blood plasma on patients with chronic pancreatitis and operable and inoperable pancreatic adenocarcinoma

Currently, the most examinations and markers are of limited diagnostic and prognostic value in chronic inflammation of the pancreas and its malignant tumorous disease. The purpose of this pilot study was to measure thermal changes of blood plasma by differential scanning calorimetry (DSC) method on patients with chronic pancreatitis, and with operable or inoperable pancreatic adenocarcinoma. The study involved chronic pancreatitis patients (n = 5), in whom had to perform surgery due to any complications. In malignant pancreatic cancer group, according to resectability of the tumors, patients were divided into operable (curative R0 resection, n = 11) and inoperable (palliative double bypass, n = 5) subgroups. Peripheral blood samples were collected from the patients preoperatively and from healthy controls (n = 5). Denaturation of plasma components was detected in Setaram Micro DSC-II calorimeter. DSC results showed decrease of T _m1 (48.8 °C) and T _m2 (61.8 °C) and increase of T _m3 (68 °C) in chronic pancreatitis group compared to healthy controls (56.2, 63.1 and 68 °C). Similar tendencies were in patients with operable (48.2, 61.5, 67.6 °C) and inoperable (48.1, 62.4, 69 °C) pancreas adenocarcinoma. Calorimetric enthalpy mildly decreased in each group except for operable group (1.3 J g^?1 ?H) compared to controls (1.2 J g^?1 ?H). This research confirmed that DSC parameters of blood plasma on patients with chronic pancreatitis and pancreatic adenocarcinoma are clearly distinct from thermodynamical data of healthy controls. After better validation of calorimetric data, it can be a noninvasive tool for diagnostic and monitoring of pancreatic diseases.     

Studies on the Cure Reaction and Relationship between Network Structure/Thermal Properties of Styrene Copolymers Based on Adypic/Sebacic Acid Modified Unsaturated (Epoxy) Polyesters

The studies on the relationship between network structure/thermal properties of styrene copolymers based on adypic/sebacic acid modified unsaturated (epoxy) polyesters cured using different hardeners as well as the course of the cure reaction of polyesters with styrene have been presented. The adypic/sebacic acid modified unsaturated polyesters (UP) prepared from 4-cyclohexene-1,2-dicarboxylic anhydride (THPA), maleic anhydride (MA), adypic acid (AA) or sebacic acid (SA) and ethylene glycol (EG) and their epoxy derivatives: adypic/sebacic acid modified unsaturated epoxy polyesters (UEP) were subjected to the cure process with styrene using diacyl peroxide: benzoyl peroxide (BPO) or the mixture of BPO/suitable acid anhydride: 4-cyclohexene-1,2-dicarboxylic anhydride (THPA) or glutaric anhydride (GA). Thermal properties were evaluated by means of DSC, TG and DMA analyses. It was proved that studied properties were significantly depended on polyester's structure and the type of applied curing system. Generally, higher values of E'_20°C, tgδ_max, E”, ν_e, IDT, T_k for styrene copolymers based on UEP were obtained. It was connected with more cross-linked polymer network structure due to the possible copolymerization reaction of carbon-carbon double bonds of polyester with styrene and additional polyaddition of epoxy to anhydride groups or thermal curing of epoxy groups. The additional connections between polyester's chains led to obtain more stiff and thermal stable polymeric materials. Moreover, the increase of saturated aliphatic acid's chain length in polyester backbone caused the decrease of E'_20°C, tgδ_max, E”, ν_e, IDT, T_k values of styrene copolymers. It suggested that copolymers based on polyesters prepared from acid containing more methylene groups in their structure were characterized by more flexible polymer network due to the “laxity” effect of aliphatic chains.     

The influence of sodium chloride on the melting temperature of collagen crystalline region in parchments

In order to observe the influence of sodium chloride on the melting temperature of collagen crystalline region in three new parchments, samples were soaked in water (blanks) and NaCl solutions of different concentrations, then removed, dried in air and measured by means of differential scanning calorimetry (DSC) and dynamic mechanical analysis (DMA). The melting temperature of crystalline region of collagen, T _m, was determined as the minimum of the endothermal peak in the range 200–250 °C and as the inflection point of the decrease of storage modulus, respectively. There was observed a decrease in melting temperature of the salt-treated parchments compared to the samples soaked in water, sometimes significant (~20 °C) at certain concentrations of NaCl. Simultaneous TG/DTG/DSC thermal analysis (STA) was also applied for the determination of the amount of sodium chloride in salt-treated parchments, by calculating the mass loss due to the vaporization of NaCl, which occurs above 800 °C. By plotting T _m determined by DSC and DMA versus the NaCl content of the samples, an apparent minimum is observed. Additional information regarding the structural features was also obtained through X-ray diffraction (XRD) and attenuated total reflection fourier transform infrared spectroscopy (ATR-FTIR). XRD data put in evidence the preservation of collagen crystalline region in all salt-treated samples, while FTIR measurements did not showed significant modification of collagen. By removing the sodium chloride from the salt-treated parchments through washing with water, there is a return of the melting temperatures to the values of blank samples, demonstrating the reversibility of this phenomenon.     

Differential scanning calorimetric examination of pathologic scar tissues of human skin

Keloid and hypertrophic scarring is a dermal fibroproliferative disorder characterized by increased fibroblast proliferation and excessive production of collagen. Excess scar formation occurs after dermal injury as a result of abnormal wound healing. Keloid formation has been ascribed to altered growth factor regulation, aberrant collagen turnover, genetics, immune dysfunction, sebum reaction, and altered mechanics. No single hypothesis adequately explains keloid formation. The thermal denaturations of pathologic human skin scar tissues were monitored by a SETARAM Micro DSC-II calorimeter. All the experiments were performed between 0 and 100 °C. The heating rate was 0.3 K min^?1. DSC scans clearly demonstrated significant differences between the different types and conditions of samples (intact skin: T _m = 54.8 °C and ΔH _cal = 4.5 J g^?1; normal scar: T _m = 53.8 °C and ΔH _cal = 4.2 J g^?1; hypertrophic scar: T _m = 54.2 °C and ΔH _cal = 2.4 J g^?1; keloid: T _m = 52.9 °C and ΔH _cal = 8.3 J g^?1). The heat capacity change between native and denatured states of samples increased with the degree of structural alterations indicating significant water loosing. These observations could be explained with the structural alterations caused by the biochemical processes. With our investigations, we could demonstrate that DSC is a useful and well-applicable method for the investigation of collagen tissue of the human keloid and hypertrophic scar tissues. Our results may be of clinical relevance in the future, i.e., in the diagnosis of the two different pathologic scar formations, or in the choice of the optimal therapy of the disease.     

Investigation of thermal behavior of Heliotropium indicum L. lyophilized extract by TG and DSC

Thermogravimetric (TG) techniques and differential scanning calorimetry (DSC) used for the study of pre-formulation or drug–adjuvant compatibility have been gaining importance in Brazil. These techniques are being used for the verification of possible interactions between drugs and adjuvants. Aiming at studying the behavior of a plant extract and its mixture with adjuvants, using these thermoanalytical techniques the plant species Heliotropium indicum L. was used. This plant which is originally from India and has been well acclimatized in Brazil has healing and anti-inflammatory properties. The methodology for obtaining the extract followed the Brazilian Pharmacopoeia methodology. And the incorporation of the extract with adjuvants was through binary mixtures (1:1 w/w). The TG and DSC curves were obtained under nitrogen atmosphere (25 mL min^?1) at a heating rate of 5 °C min^?1; TG tests were analyzed within a temperature range from 25 to 600 °C and DSC from 25 to 300 °C. The TG curves show good thermal stability of the extract and its mixtures with adjuvants up to 150 °C, except the propylene glycol (PLG). The DSC curves revealed an incompatibility of the extract with methylparaben and PLG mixture.     

Microcalorimetric study of the effect of manganese on the growth and metabolism in a heterogeneously expressing manganese-dependent superoxide dismutase (Mn-SOD) strain

DSC, SEM–EDS, XRD and high-temperature XRD analysis was used to study thermal and crystallization behaviour of yttrium aluminate glasses prepared in the form of microspheres. The glasses YA-E (eutectic composition from the pseudo-binary system Al₂O₃–Y₃Al₅O₁₂) and YA-G (a composition identical to the stoichiometric Y₃Al₅O₁₂ (YAG) phase) were prepared by combination of the Pechini method with flame synthesis. The resulting microspheres were largely amorphous, but contained traces of yttrium–aluminium garnet as the main crystalline phase embedded in the yttrium aluminate glass matrix. Crystallization of the YAG phase was observed as the dominant exothermic process on DSC curves. From the DSC records, the basic thermal characteristics of the matrix glass, i.e. T _g (glass transition temperature), T _x (onset of crystallization peak temperature), T _f (temperature of the inflection point of the crystallization peak) and T _p (maximum of crystallization peak temperature), were determined. HT XRD experiments in the temperature interval 750–1200 °C and isothermal HT XRD experiments at 932, 998 and 1200 °C with 6-h holding time were also performed. Crystallization experiments at lower temperatures 932 °C (YA-E) and 915 °C (YA-G) were conducted to study phase development in a low-temperature region. Crystallization experiments at higher temperatures (1000, 1300 and 1500 °C) with maximum holding time of 6 h were performed to study crystallization of α-Al₂O₃ in the eutectic system. The SEM and SEM–EDS examination of polished cross sections of crystallized microspheres revealed slow volume crystallization of the YAG phase in the AY-E glass. Eventually, polycrystalline microspheres with fine-grained microstructure were prepared after 6-h treatment at 1500 °C.     

Thermal parameters study of 1,1-bis(tert-butylperoxy)cyclohexane at low heating rates with differential scanning calorimetry

Having two active peroxide groups, 1,1-bis(tert-butylperoxy)cyclohexane (BTBPC) has a certain degree of thermal instability. It is usually used as an initiator in a chemical process, and therefore, careless operation could result in severe accidents. This study emphasized the runaway reactions of BTBPC 70 mass% (4.5–5.2 mg), the relevant thermokinetic parameters, and the thermal safety parameters. Differential scanning calorimetry was used to evaluate the above-mentioned thermokinetic parameters, using four low heating rates (0.5, 1, 2, and 4 °C min^?1) combined with kinetic simulation method. The results indicated that apparent exothermic onset temperature (T _o), apparent activation energy (E _a), and heat of decomposition (ΔH _d) were ca. 118 °C, 156 kJ mol^?1, and 1,080 kJ kg^?1, respectively. In view of process loss prevention, at the low heating rates of 0.5, 1, 2, and 4 °C min^?1, storing BTBPC 70 mass% below 27.27 °C is a more reassuring approach.     

Studies on the thermal behavior and decomposition kinetic of drugs cetirizine and simvastatin

Understanding the response of drugs and their formulations to thermal stresses is an integral part of the development of stable medicinal products. In the present study, the thermal degradation of two drug samples (cetirizine and simvastatin) was determined by differential scanning calorimetery (DSC) and simultaneous thermogravimetery/differential thermal analysis (TG/DTA) techniques. The results of TG analysis revealed that the main thermal degradation for the cetirizine occurs during two temperature ranges of 165–227 and 247–402 °C. The TG/DTA analysis of simvastatin indicates that this drug melts (at about 143 °C) before it decomposes. The main thermal degradation for the simvastatin occurs during two endothermic behaviors in the temperature ranges of 238–308 and 308–414 °C. The influence of the heating rate (5, 10, 15, and 20 °C min^?1) on the DSC behavior of both the drug samples was verified. The results showed that as the heating rate was increased, decomposition temperatures of the compounds were increased. Also, the kinetic parameters such as activation energy and frequency factor for the compounds were obtained from the DSC data by non-isothermal methods proposed by ASTM E696 and Ozawa. Based on the values of activation energy obtained by ASTM E696 method, the values of activation energy for cetirizine and simvastatin were 120.8 and 170.9 kJ mol^?1, respectively. Finally, the values of ΔS ^#, ΔH ^#, and ΔG ^# of their decomposition reaction were calculated.