SnS-quantum dot solar cells using novel TiC counter electrode and organic redox couples

Low-cost quantum-dot sensitized solar cells (QDSSCs) were fabricated by using the earth-abundant element SnS quantum dot, novel TiC counter electrodes, and the organic disulfide/thiolate (T(2)/T(-)) redox couple, and reached an efficiency of 1.03?%. QDSSCs based on I(-)/I(3)(-), T(2)/T(-), and S(2-)/S(x)(2-) redox couples were assembled to study the role of the redox couples in the regeneration of sensitizers. Charge-extraction results reveal the reasons for the difference in J(SC) in three QDSSCs based on I(-)/I(3)(-), T(2)/T(-), and S(2-)/S(x)(2-) redox couples. The catalytic selectivity of TiC and Pt towards T(2)/T(-) and I(-)/I(3)(-) redox couples was investigated using Tafel polarization and electrochemical impedance analysis. These results indicated that Pt and TiC show a similar catalytic selectivity for I(-)/I(3)(-). However, TiC possesses better catalytic activity for T(2)/T(-) than for I(-)/I(3)(-). These results indicate the great potential of transition metal carbide materials and organic redox couples used in QDSSCs.     

Electrochemical impedance spectra of CdSe quantume dots sensitized nanocrystalline TiO_2 solar cells

Quantum dots sensitized nanocrystalline TiO2 solar cells (QDSSCs) are promising third-generation photovoltaic devices.In comparison with conventional dye-sensitized solar cells (DSSCs),the efficiency of QDSSCs is still very low (about 3%).In this paper,the electrochemical impedance spectroscopy technology has been adopted to investigate the quasi-Fermi level and the carrier dynamics of the colloidal CdSe QDs sensitized TiO2 eletrode with S2-/Sxredox electrolytes and the series resistance of the QDSSCs.In co...     

CdSe量子点敏化纳米二氧化钛太阳电池的电化学交流阻抗谱

量子点敏化纳米TiO2太阳电池(QDSSCs)具有诱人的发展前景,但是与传统的染料敏化太阳电池(DSSCs)相比,其目前的光电转换效率还非常低(仅为3%左右).为了寻找QDSSCs光电转换效率低的原因,本文主要采用外加偏压下的交流阻抗谱技术对通常以S2-/S-x离子对为电解质的CdSe胶体量子点敏化纳米TiO2电极的准...     

Economical and effective sulfide catalysts for dye-sensitized solar cells as counter electrodes

Molybdenum sulfide (MoS(2)) and tungsten sulfide (WS(2)) are proposed as counter electrode (CE) catalysts in a I(3)(-)/I(-) and T(2)/T(-) based dye-sensitized solar cells (DSCs) system. The I(3)(-)/I(-) based DSCs using MoS(2) and WS(2) CEs achieved power conversion efficiencies of 7.59% and 7.73%, respectively.     

A flexible photoelectrode for CdS/CdSe quantum dot-sensitized solar cells (QDSSCs)

We, for the first time, prepared a flexible photoelectrode for CdS/CdSe quantum dot-sensitized solar cells (QDSSCs). A power conversion efficiency of 3.47% was achieved under AM 1.5G illumination for a sandwich type QDSSC consisting of this flexible photoelectrode, Cu(2)S counter electrode and polysulfide electrolyte between the electrodes.     

Tuning the HOMO energy levels of organic dyes for dye-sensitized solar cells based on Br-/Br3- electrolytes

A series of novel metal-free organic dyes TC301-TC310 with relatively high HOMO levels were synthesized and applied in dye-sensitized solar cells (DSCs) based on electrolytes that contain Br(-)/Br(3)(-) and I(-)/I(3)(-). The effects of additive Li(+) ions and the HOMO levels of the dyes have an important influence on properties of the dyes and performance of DSCs. The addition of Li(+) ions in electrolytes can broaden the absorption spectra of the dyes on TiO(2) films and shift both the LUMO levels of the dyes and the conduction band of TiO(2), thus leading to the increase of J(sc) and the decrease of V(oc). Upon using Br(-)/Br(3)(-) instead of I(-)/I(3)(-), a large increase of V(oc) is attributed to the enlarged energy difference between the redox potentials of electrolyte and the Fermi level of TiO(2), as well as the suppressed electron recombination. Incident photon to current efficiency (IPCE) action spectra, electrochemical impedance spectra, and nanosecond laser transient absorption reveal that both the electron collection yields and the dye regeneration yields (Φ(r)) depend on the potential difference (the driving forces) between the oxidized dyes and the Br(-)/Br(3)(-) redox couple. For the dyes for which the HOMO levels are more positive than the redox potential of Br(-)/Br(3)(-) sufficient driving forces lead to the longer effective electron-diffusion lengths and almost the same efficient dye regenerations, whereas for the dyes for which the HOMO levels are similar to the redox potential of Br(-)/Br(3)(-), insufficient driving forces lead to shorter effective electron-diffusion lengths and inefficient dye regenerations.     

Self-supported metal sulphide nanocrystals-assembled nanosheets on carbon paper as efficient counter electrodes for quantum-dot-sensitized solar cells

Developing efficient counter electrodes (CEs) and quantum dots made of earth-abundant and non-toxic elements is essential but still challenging for quantum dot-sensitized solar cells (QDSSCs). Here, we report a facile strategy to prepare self-supported and robust CoS₂ and NiS nanocrystals-assembled nanosheets directly grown on carbon paper (MSx NS@CP) as efficient counter electrodes for QDSSCs. Such CEs integrate the merits of fast electron transfer from interconnected conductive scaffold, efficient mass transfer from hierarchically vertical nanosheet on 3D open substrate, as well as abundant highly active catalytic sites from metal sulphide nanocrystal units. As a result, QDDSCs based on such CoS₂ NS@CP and NiS NS@CP CEs achieve a PCE of 8.88% and 7.53%, respectively. The detailed analyses suggest that CoS₂ NS@CP has the highest catalytic activity and shows the lowest charger transfer resistance, leading to the highest PCE. These findings may inspire the design and exploration of other self-supported efficient CEs by integrating highly active catalysts onto 3D conductive networks for efficient QDSSCs.     

High molar extinction coefficient heteroleptic ruthenium complexes for thin film dye-sensitized solar cells

Two novel heteroleptic sensitizers, Ru((4,4-dicarboxylic acid-2,2'-bipyridine)(4,4'-bis(p-hexyloxystyryl)-2,2-bipyridine)(NCS)2 and Ru((4,4-dicarboxylic acid-2,2'-bipyridine)(4,4'-bis(p-methoxystyryl)-2,2'-bipyridine) (NCS)2, coded as K-19 and K-73, respectively, have been synthesized and characterized by 1H NMR, FTIR, UV-vis absorption, and emission spectroscopy and excited-state lifetime and spectroelectrochemical measurements. The introduction of the alkoxystyryl group extends the conjugation of the bipyridine donor ligand increasing markedly their molar extinction coefficient and solar light harvesting capacity. The dynamics of photoinduced charge separation following electronic excitation of the K-19 dye was scrutinized by time-resolved laser spectroscopy. The electron transfer from K-19 to the conduction band of TiO2 is completed within 20 fs while charge recombination has a half-life time of 800 s. The high extinction coefficients of these sensitizers enable realization of a new generation of a thin film dye sensitized solar cell (DSC) yielding high conversion efficiency at full sunlight even with viscous electrolytes based on ionic liquids or nonvolatile solvents. An unprecedented yield of over 9% was obtained under standard reporting conditions (simulated global air mass 1.5 sunlight at 1000 W/m2 intensity) when the K-73 sensitizer was combined with a nonvolatile "robust" electrolyte. The K-19 dye gave a conversion yield of 7.1% when used in conjunction with the binary ionic liquid electrolyte. These devices exhibit excellent stability under light soaking at 60 degrees C. The effect of the mesoscopic TiO2 film thickness on photovoltaic performance has been analyzed by electrochemical impedance spectroscopy (EIS).     

Solid-state composite electrolyte LiI/3-hydroxypropionitrile/SiO2 for dye-sensitized solar cells

A new compound, LiI(3-hydroxypropionitrile)(2), is reported here. According to its single-crystal structure (C2/c), this compound has 3-D transporting paths for iodine. Further ab initio calculation shows that the activation energy for diffusion of iodine (0.73 eV) is much lower than that of lithium ion (8.39 eV) within the lattice. Such a mono-ion transport feature is favorable as solid electrolyte to replace conventional volatile organic liquid electrolytes used in dye-sensitized solar cells (DSSC). LiI and 3-hydroxypropionitrile (HPN) can form a series of solid electrolytes. The highest ambient conductivity is 1.4 x 10(-)(3) S/cm achieved for LiI(HPN)(4). However, it tends to form large crystallites and leads to poor filling and contact within porous TiO(2) electrodes in DSSC. Such a drawback can be greatly improved by introducing micrometer-sized and nanosized SiO(2) particles into the solid electrolyte. It is helpful not only in enhancing the conductivity but also in improving the interfacial contact greatly. Consequently, the light-to-electricity conversion efficiency of 5.4% of a DSSC using LiI(HPN)(4)/15 wt % nano-SiO(2) was achieved under AM 1.5 simulated solar light illumination. Due to the low cost, easy fabrication, and relatively high conversion efficiency, the DSSC based on this new solid-state composite electrolyte is promising for practical applications.     

Dye sensitization of nanocrystalline titanium dioxide with square planar platinum(II) diimine dithiolate complexes

A series of platinum-based sensitizers of the general type Pt(NN)(SS), where NN is 4,4'-dicarboxy-2,2'-bipyridine (dcbpy) or 4,7-dicarboxy-1,10-phenanthroline (dcphen) and SS is ethyl-2-cyano-3,3-dimercaptoacrylate (ecda), quinoxaline-2,3-dithiolate (qdt), 1,2-benzenedithiolate (bdt), or 3,4-toluenedithiolate (tdt), that have various ground-state oxidation potentials has been synthesized and anchored to nanocrystalline titanium dioxide electrodes for light-to-electricity conversion in regenerative photoelectrochemical cells with an I(-)/I(-)(3) acetonitrile electrolyte. The intense mixed-Pt/dithiolate-to-diimine charge-transfer absorption bands in this series could be tuned from 440 to 580 nm by choosing appropriate dithiolate ligands, and the highest occupied molecular orbitals varied by more than 500 mV. Spectrophotometric titration of the Pt(dcphen)(bdt) complex exhibits a ground-state pK(a) value of 3.2 +/- 0.1, which can be assigned to the protonation of the carboxylate group of the dcphen ligand. Binding of Pt(dcbpy)(qdt) to porous nanostructured TiO(2) films was analyzed using the Langmuir adsorption isotherm model, yielding an adsorption equilibrium constant of 4 x 10(5) M(-1). The amount of dye adsorbed at the surface of TiO(2) films was 9.5 x 10(-8) mol/cm(2), which is ca. 50% lower than the full monolayer coverage. The resulting complexes efficiently sensitized TiO(2) over a notably broad spectral range and showed an open-circuit potential of ca. 600 mV with an impressive fill factor of > 0.70, making them attractive candidates for solar energy conversion applications. The visible spectra of the 3,4-toluenedithiol-based sensitizers showed an enhanced red response, but the lower photocurrent efficiency observed for these sensitizers stems in part from a sluggish halide oxidation rate and a fast recombination of injected electrons with the oxidized dye.     

Synergistic effect of ZnS outer layers and electrolyte methanol content on efficiency in TiO(2)/CdS/CdSe sensitized solar cells

The effect of methanol content in water based polysulfide electrolytes in TiO(2)/CdS/CdSe quantum dot sensitized solar cells (QDSSCs) prepared by the SILAR method was studied. In addition, the effect of coating the mesoporous QD sensitized films with ZnS outer layers was investigated. Charge recombination reactions were measured using time resolved spectroscopic measurements. These studies reveal a synergistically beneficial effect from using ZnS layers and methanol in the polysulfide electrolyte on the control of charge transfer processes within these devices and ultimately on overall cell performance.     

Highly efficient CdS quantum dot-sensitized solar cells based on a modified polysulfide electrolyte

A modified polysulfide redox couple, [(CH(3))(4)N](2)S/[(CH(3))(4)N](2)S(n), in an organic solvent (3-methoxypropionitrile) was employed in CdS quantum dot (QD)-sensitized solar cells (QDSSCs), and an unprecedented energy conversion efficiency of up to 3.2% was obtained under AM 1.5 G illumination. The QDs were linked to nanoporous TiO(2) via covalent bonds by using thioglycolic acid, and chemical bath deposition in an organic solvent was then used to prepare the QDSSCs, facilitating high wettability and superior penetration capability of the TiO(2) films. A very high fill factor of 0.89 was observed with the optimized QDSSCs.     

Investigation on the dynamics of electron transport and recombination in TiO2 nanotube/nanoparticle composite electrodes for dye-sensitized solar cells

In this work, we report on fabrication and characterization of dye-sensitized solar cells based on TiO(2) nanotube/nanoparticle (NT/NP) composite electrodes. TiO(2) nanotubes were prepared by anodization of Ti foil in an organic electrolyte. The nanotubes were chemically separated from the foil, ground and added to a TiO(2) nanoparticle paste, from which composite NT/NP electrodes were fabricated. In the composite TiO(2) films the nanotubes existed in bundles with a length of a few micrometres. By optimizing the amount of NT in the paste, dye-sensitized solar cells with an efficiency of 5.6% were obtained, a 10% improvement in comparison to solar cells with pure NP electrodes. By increasing the fraction of NT in the electrode the current density increased by 20% (from 11.1 to 13.3 mA cm(-2)), but the open circuit voltage decreased from 0.78 to 0.73 V. Electron transport, lifetime and extraction studies were performed to investigate this behavior. A higher fraction of NT in the paste led to more and deeper traps in the resulting composite electrodes. Nevertheless, faster electron transport under short-circuit conditions was found with increased NT content, but the electron lifetime was not improved. The electron diffusion length calculated for short-circuit conditions was increased 3-fold in composite electrodes with an optimized NT fraction. The charge collection efficiency was more than 90% over a wide range of light intensities, leading to improved solar cell performance.     

The influence of dye structure on charge recombination in dye-sensitized solar cells

Replacing the nonyl groups on the solar cell dye Ru(4,4'-carboxylic acid-2,2'-bipyridine)(4,4'-dinonyl-2,2'-bipyridine)(NCS)(2) (Z-907) with amino groups results in a marked decrease in solar cell performance. This is despite the fact that the amino derivative (Z-960) has more favourable light absorption characteristics than Z-907 when used with thick nanocrystalline TiO(2) layers. Electron transfer to the electrolyte from the exposed fluorine-doped tin oxide (FTO) substrate is particularly fast in cells employing the Z-960 dye if a compact TiO(2) blocking layer is not used. The kinetics of electron transfer from the nanocrystalline TiO(2) layer in DSCs employing Z-960 are comparable to those of bare TiO(2) and ca. 2 to 5 times faster than for cells employing Z-907. The faster charge recombination in cells employing Z-960 lowers open-circuit photovoltage and results in very significant charge collection losses that lower short-circuit photocurrent. Voltammetric measurements show that surface modification of FTO electrodes with Z-960 results in slightly more facile charge transfer to acceptor species in triiodide/iodide electrolytes in the dark. A simpler molecule, p-aminobenzoic acid, more dramatically catalyses this charge transfer reaction. Conversely, chemical modification of FTO electrodes with Z-907 or p-toluic acid retards charge transfer kinetics. Similar results are obtained for nanocrystalline TiO(2) electrodes modified with these benzoic acid derivatives. These results strongly imply that surface adsorbed molecules bearing amino groups, including dye molecules, can catalyse charge recombination in dye-sensitized solar cells.     

Fast electron transport in metal organic vapor deposition grown dye-sensitized ZnO nanorod solar cells

The electron transport in dye-sensitized solar cells with a MOCVD (metal organic vapor deposition)-grown ZnO nanorod array (ZnO-N) or a mesoporous film prepared from ZnO colloids (ZnO-C) as the working electrode was compared. The electrodes were of similar thickness (2 mum) and sensitized with zinc(II) meso-tetrakis(3-carboxyphenyl)porphyrin, while the electrolyte was I(-)/I(3)(-) in 3-methoxypropionitrile. Electron transport in the ZnO-C cells was comparable with that found for colloidal TiO(2) films (transport time approximately 10 ms) and was light intensity dependent. Electron transport in solar cells with ZnO-N electrodes was about 2 orders of magnitude faster ( approximately 30 mus). Thus, the morphology of the working ZnO electrode plays a key role for the electron transport properties.     

Combined experimental and DFT-TDDFT computational study of photoelectrochemical cell ruthenium sensitizers

We report a combined experimental and computational study of several ruthenium(II) sensitizers originated from the [Ru(dcbpyH(2))(2)(NCS)(2)], N3, and [Ru(dcbpyH(2))(tdbpy)(NCS)(2)], N621, (dcbpyH(2) = 4,4'-dicarboxy-2,2'-bipyridine, tdbpy = 4,4'-tridecyl-2,2'-bipyridine) complexes. A purification procedure was developed to obtain pure N-bonded isomers of both types of sensitizers. The photovoltaic data of the purified N3 and N621 sensitizers adsorbed on TiO(2) films in their monoprotonated and diprotonated state, exhibited remarkable power conversion efficiency at 1 sun, 11.18 and 9.57%, respectively. An extensive Density Functional Theory (DFT)-Time Dependent DFT study of these sensitizers in solution was performed, investigating the effect of protonation of the terminal carboxylic groups and of the counterions on the electronic structure and optical properties of the dyes. The calculated absorption spectra are in good agreement with the experiment, thus allowing a detailed assignment of the UV-vis spectral features of the two types of dyes. The computed alignments of the molecular orbitals of the different complexes with the band edges of a model TiO(2) nanoparticle provide additional insights into the electronic factors governing the efficiency of dye-sensitized solar cell devices.     

Low‐cost Nickel Complex Dye‐sensitized Titania Nanoparticle/nanotube Composites for Solar Cells

In this work, high‐performance dye‐sensitized solar cells (DSSCs) based on new low‐cost visible nickel complex dye (VisDye), TiO₂ nanoparticle/nanotube composites electrodes, carbon nanoparticles counter electrodes, and ionic liquids electrolytes have been fabricated. The electronic structure, optical spectroscopy, and electrochemical properties of the VisDye were studied. Experimental results indicate that it is beneficial to improve the electron transport and power conversion efficiency using the nickel complex VisDye and TiO₂ nanoparticle/nanotube composites. Under optimized conditions, the solar energy conversion efficiencies were measured. The short‐circuit current density (J_SC), the open‐circuit voltage (V_OC), the fill factor (FF), and the overall efficiency (η) of the DSSCs are 10.01 mA/cm², 516 mV, 0.68, and 3.52%, respectively. This study demonstrates that the combination of new VisDye with TiO₂ nanoparticle/nanotube composites electrodes and carbon nanoparticles counter electrodes provide a way to fabricate highly efficient dye‐sensitized solar cells in low‐cost production.     

Dye-sensitized SnO2 electrodes with iodide and pseudohalide redox mediators

Dye-sensitized mesoporous nanocrystalline SnO2 electrodes and the pseudohalogen redox mediator (SeCN)2/SeCN- or (SCN)2/SCN- or the halogen redox mediator I3-/I- were implemented for regenerative solar cell studies. Adsorption isotherms of the sensitizers Ru(deeb)(bpy)2(PF6)2, Ru(deeb)2(dpp)(PF6)2, and Ru(deeb2(bpz)(PF6)2, where deeb is 4,4'-diethylester-2,2'-bipyridine, dpp is 2,3-dipyridyl pyrazine, and bpz is bipyrazine, binding to the SnO2 surface were well described by the Langmuir model from which the saturation coverage, Gamma0 = 1.7 x 10(-8) mol/cm2, and surface-adduct formation constant, Kad = 2 x 10(5) M(-1), were obtained. Following excited-state interfacial electron transfer, the oxidized sensitizers were reduced by donors present in the acetonitrile electrolyte as shown by transient absorption spectroscopy. With iodide as the donor, a rate constant k > 10(8) s(-1) was measured for sensitizer regeneration. In regenerative solar cells, it was found that the incident photon-to-current conversion efficiencies and open circuit voltages (Voc) were comparable for (SeCN)2/SeCN- and I3-/I- for all three sensitizers. The Voc varied linearly with the logarithm of the short circuit photocurrent densities (Jsc), with typical correlations of approximately 50-60 mV/decade. Capacitance measurements of the SnO2 electrode in the presence of I3-/I-, (SeCN)2/SeCN- or (SCN)2/SCN- are reported.     

Double-layer coating of SrCO3/TiO2 on nanoporous TiO2 for efficient dye-sensitized solar cells

Surface modification plays a crucial role in improving the efficiency of dye-sensitized solar cells (DSSCs), but the reported surface treatments are in general superior to the untreated TiO(2) but inferior to the typical TiCl(4)-treated TiO(2) in terms of solar cell performance. This work demonstrates a two-step treatment of the nanoporous titania surface with strontium acetate [Sr(OAc)(2)] and TiCl(4) in order, each step followed by sintering. An electronically insulating layer of SrCO(3) is formed on the TiO(2) surface via the Sr(OAc)(2) treatment and then a fresh TiO(2) layer is deposited on top of the SrCO(3) layer via the TiCl(4) treatment, corresponding to a double layer of Sr(OAc)(2)/TiO(2) coated on the TiO(2) surface. As compared to the typical TiCl(4)-treated DSSC, the Sr(OAc)(2)-TiCl(4) treated DSSC improves short-circuit photocurrent (J(sc)) by 17%, open-circuit photovoltage (V(oc)) by 2%, and power conversion efficiency by 20%. These results indicate that the Sr(OAc)(2)-TiCl(4) treatment is better than the often used TiCl(4) treatment for fabrication of efficient DSSCs. Charge density at open circuit and controlled intensity modulated photocurrent/photovoltage spectroscopy reveal that the two electrodes show almost same conduction band level but different electron diffusion coefficient and charge recombination rate constant. Owing to the blocking effect of the SrCO(3) layer on electron recombination with I(3)(-) ions, the charge recombination rate constant of the Sr(OAc)(2)-TiCl(4) treated DSSC is half that of the TiCl(4)-treated DSSC, accounting well for the difference of their V(oc). The improved J(sc) is also attributed to the middle SrCO(3) layer, which increases dye adsorption and may improve charge separation efficiency due to the blocking effect of SrCO(3) on charge recombination.     

花状硫化铜的合成及其光电催化性能

通过硫化介孔Cu_2O微球得到花状Cu_xS纳米催化材料,并采用丝网印刷法制备出Cu_xS/FTO对电极。通过X射线衍射(XRD)、扫描电子显微镜(SEM)、透射电子显微镜(TEM)等表征手段对所得材料的结构和形貌进行了探究,同时系统考察了溶液浓度、硫化时间、催化剂印刷层数对Cu_xS/FTO电极的催化性能影响和所组装量子点敏化太阳电池的光电转换效率,其中基于Zn-Cu-In-Se量子点敏化的电池转换效率达8.80%,表现出花状Cu_xS优异的光电催化性能。