Interaction between a nonionic surfactant and a hydrophobically modified 2-hydroxyethyl cellulose

Interaction between the nonionic surfactant Tergitol 15-S-7 and hydrophobically modified 2-hydroxyethyl cellulose (HMHEC) was studied rheologically in a semidilute regime of HMHEC. The low-shear viscosity of HMHEC was increased with addition of surfactant from 25 to 250 ppm, in which the critical micelle concentration of surfactant was near 39 ppm, and then decreased to a value smaller than that of pure HMHEC with further addition of surfactant to 1000 ppm. An interesting shear-induced phenomenon was observed. The steady-state shear measurements show that there exist crossovers between viscosity-shear rate curves of HMHEC solutions with and without surfactant added, whereas it was not observed in the HEC-surfactant systems. Moreover, added Tergitol 15-S-7 reversed the temperature effect on the viscosity of the HMHEC solution. That is, increasing temperature to or near the cloud point raises the viscosity of the HMHEC-surfactant aggregates, in contrast to the viscosity decrease in the pure HMHEC solutions. A possible mechanism based on the necklace model and the clouding phenomenon is conjecturally introduced to explain such phenomena.     

Slurries and emulsions of waxy and heavy crude oils for pipeline transportation of crude oil

The high viscosity of many asphaltic crude oils and the high pour points of many waxy crude oils present significant problems in their transportation over long distances by pipeline and tanker. While heating the oils and insulating the pipelines will help alleviate the problem, there is danger associated with an extended shutdown of flow and either congealing or solidification of the oil. A possible solution which we have studied in the laboratory is the emulsification or dispersion of the oil in water or brine so that shear takes place in the continuous aqueous phase rather than the oil droplets or particles.Synthetic waxy crude oils were prepared by dissolving paraffin wax in white mineral oil at slightly elevated temperatures and then measuring the pour point. One containing 30% wax had a pour point of 43°C and was selected for preparations of the dispersions. This was emulsified in water at a temperature higher than the pour point by using a suitable surfactant as an emulsifying agent. Rheological properties were measured at various temperatures and are reported in the paper. The method shows great promise for use in countries such as China which produce significant quantities of waxy crude oil and have seasonal temperatures significantly lower than the pour point of the crude oil.     

Synergistic effects in flows of mixtures of wormlike micelles and hydroxyethyl celluloses with or without hydrophobic modifications

This work presents experimental results on simple shear and porous media flow of aqueous solutions of two hydroxyethyl celluloses (HEC) and two hydrophobically modified hydroxyethyl celluloses (HMHEC) with different molecular weights. Mixtures of these polymers with a cationic surfactant, cetyltrimethylammonium p-toluenesulfonate (CTAT) were also studied. Emphasis was given to the range of surfactant concentrations in which wormlike micelles are formed. The presence of hydrophobic groups, the effect of the molecular weight of the polymers, the surfactant and polymer concentrations, and the effect of the flow field type (simple shear versus porous media flow) were the most important variables studied. The results show that the shear viscosity of HEC/CTAT solutions is higher than the viscosities of surfactant and polymer solutions at the same concentrations, but surface tension measurements indicate that no complex formation occurs between CTAT and HEC. On the other hand, a complex driven by hydrophobic interactions was detected by surface tension measurements between CTAT and HMHEC. In this case, the viscosity of the mixture increases significantly more (up to four orders of magnitude at high CTAT concentrations) in comparison with HEC/CTAT aqueous solutions. Increments in the molecular weight of the polymers increase the interaction with CTAT and the shear viscosity of the solution, but make phase separation more feasible. In porous media flow, the polymer/CTAT mixtures exhibited higher apparent viscosities than in simple shear flows. This result suggests that the extensional component of the flow field in porous media flows leads to a stronger interaction between the polymer and the wormlike micelles, probably as a consequence of change of conformation and growth of the micelles.     

Clouding and phase behavior of nonionic surfactants in hydrophobically modified hydroxyethyl cellulose solutions

Clouding phenomena and phase behaviors of two nonionic surfactants, Triton X-114 and Triton X-100, in the presence of either hydroxyethyl cellulose (HEC) or its hydrophobically modified counterpart (HMHEC) were experimentally studied. Compared with HEC, HMHEC was found to have a stronger effect on lowering the cloud point temperature of a nonionic surfactant at low concentrations. The difference in clouding behavior can be attributed to different kinds of molecular interactions. Depletion flocculation is the underlying mechanism in the case of HEC, while the chain-bridging effect is responsible for the large decrease of cloud point for HMHEC. Composition analyses for the formed macroscopic phases were carried out to provide support for associative phase separation for the case of HMHEC, in contrast to segregative phase separation for HEC. An interesting three-phase-separation phenomenon was reported in some HMHEC/Triton X-100 mixtures at high surfactant concentrations.     

Poly(N-isopropylacrylamide). II. Effect of polymer concentration,temperature, and surfactant on the viscosity of aqueous solutions

The effects of polymer concentration, temperature, and surfactant on the rheological properties of poly(N-isopropylacrylamide), poly NIPAM, were studied. Below 28°C the viscosity decreased with increasing temperature according to the Arrhenius expression. However, at 29°C the viscosity increased to a maximum value at 32°C, the lower critical solution temperature (LCST) for aqueous polyNIPAM. Higher temperatures gave a much lower viscosity. This unusual rheological behavior was explained by the phase behavior of the polymer. Sodium dodecyl sulfate (SDS) binding to polyNIPAM increased the cloud point temperature (CPT) and attenuated the unusual rheological behavior of polyNIPAM in water. © 1993 John Wiley & Sons, Inc.     

Shear and longitudinal viscosity of non-ionic C12E8 aqueous solutions

We present an extensive set of measurements of steady shear viscosity (eta degrees(s)), longitudinal elastic modulus (M'), and ultrasonic absorption (alpha) in the one-phase isotropic liquid region of the non-ionic surfactant C12E8 aqueous solutions. Within a given temperature interval, this phase extends along the entire surfactant concentration range that could be fully covered in the experiments. In agreement with previous studies, the overall results support the presence of two separated intervals of concentration corresponding to different structural properties. In the surfactant-rich region the temperature dependence of eta degrees(s) follows an equation characteristic of glass-like systems. The ultrasonic absorption spectra show unambiguous evidence of viscoelastic behavior that can be described by a Cole-Cole relaxation formula. In this region, when both the absorption and the frequency are scaled by the static shear viscosity (eta degrees(s)), the scaled attenuation reduces to a single universal curve for all temperatures and concentrations. In the water-rich region the behavior of eta degrees(s), M', and alpha are more complex and reflect the presence of dispersed aggregates whose size increases with temperature and concentration. At these concentrations the ultrasonic spectra are characterized by a multiple decay rate. The high-frequency tail falls in the same frequency range seen at high surfactant content and exhibits similar behaviors. This contribution is ascribed to the mixture of hydrophilic terminations and water present at the micellar interfaces that resembles the condition of a concentrated polymer solution. An additional low-frequency contribution is also observed, which is ascribed to the exchange of water molecules and/or surfactant monomers between the aggregates and the bulk solvent region.     

Nonlinear rheology of aqueous solutions of hydrophobically modified hydroxyethyl cellulose with nonionic surfactant

Shear thickening and strain hardening behavior of hydrophobically modified hydroxyethyl cellulose (HMHEC) aqueous solutions was experimentally examined. We focused on the effects of polymer concentration, temperature, and addition of nonionic surfactant. It is found that HMHEC shows stronger shear thickening at intermediate shear rates in a certain concentration range. In this range, the zero-shear viscosity scales with polymer concentration as eta(0) approximately c(5.7), showing a stronger concentration dependence than for more concentrated solutions. The critical shear stress for complete disruption of the transient network follows tau(c) approximately c(1.62) in the concentrated regime. Dynamic tests of the transient network on addition of surfactants show that the enhanced zero-shear viscosity is due to an increase in network junction strength, rather than their number, which in fact decreases. The reduction in the junction number could partly explain the weak variation of strain hardening extent for low surfactant concentrations, because of longer and looser bridging chain segments, and hence lesser nonlinear chain stretching.     

Low viscosity reversed hexagonal mesophases induced by hydrophilic additives

This study reports on the formation of a low viscosity H(II) mesophase at room temperature upon addition of Transcutol (diethylene glycol mono ethyl ether) or ethanol to the ternary mixture of GMO (glycerol monooleate)/TAG (tricaprylin)/water. The microstructure and bulk properties were characterized in comparison with those of the low viscosity HII mesophase formed in the ternary GMO/TAG/water mixture at elevated temperatures (35-40 degrees C). We characterized the role of Transcutol or ethanol as inducers of disorder and surfactant mobility. The techniques used were rheology, differential scanning calorimetry (DSC), wide- and small-angle X-ray scattering (WAXS and SAXS, respectively), NMR (self-diffusion and (2)H NMR), and Fourier transform infrared (FTIR) spectroscopies. The incorporation of either Transcutol or ethanol induced the formation of less ordered HII mesophases with smaller domain sizes and lattice parameters at room temperature (up to 30 degrees C), similar to those found for the GMO/TAG/water mixture at more elevated temperatures (35-40 degrees C). On the basis of our measurements, we suggest that Transcutol or ethanol causes dehydration of the GMO headgroups and enhances the mobility of the GMO chains. As a result, these two small molecules, which compete for water with the GMO polar headgroups, may increase the curvature of the cylindrical micelles and also perhaps reduce their length. This results in the formation of fluid H(II) structures at room temperature (up to 30 degrees C). It is possible that these phases are a prelude to the H(II)-L(2) transformation, which takes place above 35 degrees C.     

Temperature-dependent vesicle formation of aqueous solutions of mixed cationic and anionic surfactants

The phase behavior of aqueous solutions of mixed cetyltrimethylammonium bromide (CTAB) and sodium octyl sulfate (SOS) was examined at different temperatures (20, 30, 40, and 50 degrees C). While stable vesicles were formed in a narrow composition range on the SOS-rich side at 20 degrees C, the range widened remarkably when the temperature was raised to 30 degrees C. Thus, the vesicle region extended to cover almost the entire composition range, CTAB:SOS = 0.5:9.5-5.0:5.0, at the total surfactant concentrations of 50-70 mM on the SOS-rich side. To analyze the temperature dependence of this phase behavior of the mixed surfactant system, DSC and fluorescence polarization measurements were performed on the system. The experimental findings obtained revealed that pseudo-double-tailed CTAB/SOS complex, the major component of the bimolecular membrane formed by the surfactant mixture, undergoes a gel (Lbeta)-liquid crystal (Lalpha) phase transition at about 26 degrees C. This phenomenon was interpreted as showing that the bimolecular membrane has no curvature and is rigid and easy to precipitate at temperatures below the phase transition point, whereas it has a curvature and is loose enough to disperse in the solution as vesicles at temperatures above the phase transition point. Vesicles formed by the anionic/cationic surfactant complex were then stable at temperatures above the phase transition temperature of the complex.     

Anomalous transition in aqueous solutions of a thermoresponsive amphiphilic diblock copolymer

The influence of shear flow on aggregation and disaggregation in aqueous solutions of the thermoresponsive methoxy-poly(ethylene glycol)-block-poly(N-isopropylacrylamide) (MPEG53-b-PNIPAAM113) copolymer that exhibits a lower critical solution temperature was investigated with the aid of turbidity, shear viscosity, and rheo small angle light scattering (rheo-SALS) methods. The turbidity results at quiescent conditions revealed a novel transition peak in the turbidity curve at intermediate temperatures, which reflects the delicate interplay between temperature-induced aggregation and shrinking of the species. A similar anomalous transition peak (located at the same temperature) was observed in the steady shear viscosity measurements at intermediate temperatures, and the amplitude of the peak was reduced with increasing shear rate as a consequence of breakup of interaggregate chains. At low temperatures (low sticking probability), enhanced shear rate generated interpolymer aggregates; whereas in the high-temperature domain (high sticking probability) association structures were broken up as the shear rate was increased. The rheo-SALS experiments disclosed growth of aggregates at low temperatures and destruction of association complexes at high temperatures. An increase of the cloud point temperature with rising shear rate is reported, which is interpreted as being a disruption of clusters under the influence of shear stresses.     

Viscosity-Temperature Behavior of Hydroxypropyl Cellulose Solution in Presence of an Electrolyte or a Surfactant: A Convenient Method to Determine the Cloud Point of Polymer Solutions

The viscosity of hydroxypropyl cellulose (HPC) solution with or without an additive has been measured continuously as a function of temperature with the help of a vibro-viscometer. The viscosity of the polymer solution showed a gradual decrease initially with increase in temperature until a particular point beyond which there was a sharp decrease in the viscosity, which coincided with the clouding of the solution. The cloud point temperature (CP) of the polymer solution was determined from the first derivative plot of viscosity vs. temperature. Effect of addition of an electrolyte or a surfactant on the CP of HPC solution has also been studied. While a decrease in CP of HPC solution in presence of fluoride, chloride, or bromide ions was observed, presence of iodide or thiocyanide ions led to an increase in the CP. However, presence of an ionic surfactant initially lowered the CP but beyond a particular surfactant concentration a sharp increase in cloud point was observed due to interaction of the surfactant with the polymer. The results suggest that surfactants with longer hydrophobic tail or more hydrophobic groups have more affinity for HPC.     

Solution behaviour of a formate capped surfactant—the oxidation product of an alcohol ethoxylate

The solution behaviour has been investigated for an alcohol ethoxylate terminated with a formic acid ester. This compound has previously been reported to be an important degradation product in the auto-oxidation of alcohol ethoxylates. In this work we have investigated the solution behaviour of the formic acid ester surfactant C₁₂H₂₅(OCH₂CH₂)₄OCHO (C12E4---OCHO). The pure formate was found to be sparsely soluble in water with no clear point at 0.1%. The critical micelle concentration was found to be 129 μM at 35°C, compared to 50 μM for the parent surfactant C₁₂H₂₅(OCH₂CH₂)₅OH (C12E5). To mimic the behaviour of the oxidised surfactant, the formate was mixed in different ratios with C12E5 and the cloud point, surface tension and critical micelle concentration (cmc) of these mixtures were studied. The gradual increase of formate was found to shift the cloud point and isotropic regions to lower temperatures. The cmc of the mixture was found to be lower than for the pure surfactant. The favourable interaction was analysed according to the non-ideal model by Rubingh and the interaction parameter, β, was determined to be −4±0.53, which is unusually large for a mixture of two non-ionic surfactants. These results indicate that the reduction of cloud point observed during oxidation of non-ionic surfactants can in part be attributed to the formation of formate esters.     

A non-ionic surfactant as a new solvent for liquid-liquid extraction of zinc(II) with 1-(2-pyridylazo)-2-naphthol

A new method for extracting zinc(II) with 1-(2-pyridylazo)-2-naphthol (PAN) has been developed, based on the fact that a micellar solution of a non-ionic surfactant separates into two phases above a certain temperature, defined as the cloud point. Polyoxyethylene nonyl phenyl ether, (PONPE-7.5; average number of ethylene oxide units 7.5) was used as the surfactant. The cloud point of a 0.40% PONPE-7.5 solution is 1 degrees , and hence the solution is turbid at room temperature. The two phases can be separated by centrifuging for 8 min at room temperature. The zinc chelate of PAN is quantitatively extracted from 50g of the solution into a small volume (about 1 ml) of the lower (surfactant-rich) phase over the pH range 8.0-11.5. After most of the supernatant solution has been removed, the amount of final solution is adjusted to 2.00 g with 0.5 g of 10% of PONPE-20 solution and water. This mixture is transparent at room temperature. The absorbance is measured as 535 nm. Concentration factors of up to 25 can be obtained by choosing appropriate amounts of final ( 2.0 g) and initial solution ( 50 g). This new technique has been applied to the determination of zinc(II) in tap water.     

Cloud point curve of nonionic surfactant related to the structures of mesoporous materials

We have investigated the phase behavior of a fluorinated surfactant R(7)(F)(EO)(7) in water. The cloud point is situated at 19 degrees C for 2 wt% of surfactant. Using this surfactant, mesoporous materials have been synthesized with micellar solution prepared either at 10 degrees C (below the cloud point) or at 40 degrees C (above the cloud point). Results show that whatever the syntheses conditions, only wormhole-like structure is recovered. The effect of perfluorodecalin addition on the fluorinated surfactant/water system was also investigated. Swollen micelles, microemulsion, and lamellar (L(alpha)) liquid crystals were identified. When perfluorodecalin is added, the cloud point is shifted toward higher temperature. As regards the mesoporous syntheses, perfluorodecalin plays a dual role. First, incorporation of perfluorodecalin leads to the formation of well ordered materials. Secondly, the pore size enlargement occurs when perfluorodecalin is added. Our results evidence that the ratio between the volume of the hydrophilic headgroup (V(H)) and the hydrophobic part (V(L)) of the surfactant is not an efficiency parameter to explain the ordering improvement of mesoporous materials and that we should rather consider the existence of the cloud point curve, which disturbs the cooperative templating mechanism (CTM).     

疏水改性羟乙基纤维素的流变性能研究

对疏水改性羟乙基纤维素(HMHEC)溶液的流变性质进行了系统研究,探讨了不同的浓度、温度、盐浓 度、pH值和剪切速率对其溶液表观粘度的影响.结果表明HMHEC溶液临界缔合浓度为0.3 g/100 ml.当HMHEC的浓度低于临界缔合浓度时,HMHEC溶液增稠以分子内缔合为主,增稠幅度小;当高于临界缔合浓度后,便会形成以大分子间缔合为主的动态物理交联网络结构.HMHEC水溶液具有良好的耐温耐盐及抗剪切性能,而且pH稳定性良好.     

Microviscosity of hydrophobically modified hydroxyethyl cellulose aqueous solutions

The microviscosity of hydrophobically modified hydroxyethyl cellulose (HMHEC) aqueous solutions is experimentally determined by conductometry with added ions as probe. Compared to its bulk viscosity, the microviscosity of HMHEC solution could be lower by four orders of magnitude. Since the electric conductivity reduction of added NaCl is almost the same for HMHEC and its unmodified counterpart at an equal weight concentration, one can conclude that the hydrophobic modification for the polymer hardly has any effect on the solution's microviscosity.     

Viscoelastic micellar solutions in nonionic fluorinated surfactant systems

The formation and rheological behavior of a viscoelastic wormlike micellar solution in an aqueous solution of a nonionic fluorinated surfactant, perfluoroalkyl sulfonamide ethoxylate, of structure C8F17SO2N(C3H7)(CH2CH2O)10H was studied. Temperature-induced viscosity growth is observed even at low-surfactant concentration (approximately 1 wt %), and viscosity reaches the maximum at a temperature T(eta)-max. Upon successive increases in the temperature, the viscosity decreases, and ultimately a phase separation occurs. Small-angle X-ray scattering (SAXS) measurements confirm the presence of cylindrical aggregates at low temperature, which undergo continuous one-dimensional growth with increasing temperature, and ultimately, an indication of a slight lamellarlike structural pattern is observed, which probably comes from the formation of micellar joints or branching. Such changes in the microstructure result in a decrease in the viscosity and stress-relaxation time, while the network structure is retained; the trends in the evolution of shear modulus (Go) and relaxation time (tauR) with temperature are in agreement with this. With increased surfactant concentration, the temperature corresponding to the viscosity maximum (T eta-max) in the temperature-viscosity curve shifts to lower values, and the viscosity at temperatures below or around T eta-max increases sharply. A viscoelastic solution with Maxwellian-type dynamic rheological behavior at low-shear frequency is formed, which is typical of entangled wormlike micelles. Rheological parameters, eta(o) and Go, show scaling relationships with the surfactant concentrations with exponents slightly greater than the values predicted by the living-polymer model, but the exponent of tauR is in agreement with the theory. Dynamic light-scattering measurements indicate the presence of fast relaxation modes, associated with micelles, and medium and slow modes, associated with transient networks. The disappearance of the slow mode and the predominance of the medium mode as the temperature increases support the conclusions derived from SAXS and rheometry.     

Solution behavior of a surfactant aldehyde–the oxidation product of an alcohol ethoxylate

It has previously been shown that alcohol ethoxylates readily undergo autoxidation and that one of the major oxidation products is the surfactant aldehyde, i.e. an ethoxylate carrying a –CH₂CHO group at the terminal end of the polyoxyethylene chain. In this work the cloud point, phase behavior and aggregation characteristics of the surfactant aldehyde produced by oxidation of C₁₂H₂₅(OCH₂CH₂)₅OH (C₁₂E₅) are determined and compared with the values obtained with the parent surfactant. It was found that the physico–chemical behavior of the two species was very similar, which indicates that a considerable portion of the aldehyde group is in hydrated state, i.e. the surfactant aldehyde consists of a mixture of aldehyde in carbonyl form and the corresponding geminal diol. The cloud point of the surfactant aldehyde decreased rapidly with time, even when it was stored at low temperature. Also the parent surfactant and its homologue C₁₂E₆ exhibited a decrease in cloud point during storage. For instance, a 1% aqueous solution of C₁₂E₆ showed a cloud point decrease from 62 to 32°C after 4 months storage at 40°C. Such a change in solution behavior can have important practical implications.     

Effect of temperature on the rheology of wormlike micelles in a mixed surfactant system

The formation and rheological behavior of a viscoelastic wormlike micellar solution in an aqueous solution of a mixed surfactant system of alkyl ethoxylate sulfate (AES), C(12)H(25)(OCH(2)CH(2))(3)OSO(-)(3)Na(+), and polyoxyethylene dodecyl ether, C(12)EO(3), and the unusual effect of temperature on the rheological behavior have been studied. Upon successive addition of C(12)EO(3) to the dilute micellar solution of AES, viscosity increases swiftly and reaches its peak where a viscoelastic solution with nearly Maxwellian behavior is formed. With the further addition of C(12)EO(3), viscosity decreases sharply, which is attributed to the formation of micellar joints. With increasing temperature, the extent of micellar growth increases and the viscosity maximum is achieved at a lower mixing fraction of C(12)EO(3), but the maximum viscosity attained by the system decreases. The evolution of relaxation time and network density of the viscoelastic network also suggests that with increasing temperature, enhanced micellar growth takes place, but an additional, faster relaxation mechanism becomes increasingly favorable at high concentrations of C(12)EO(3). These results can be explained in terms of the increase in free energy of hemispherical end-caps (end-cap energy) of the micelles with increasing temperature.     

Mixed solutions of an associating polymer with a cleavable surfactant

Mixtures of hydrophobically modified hydroxyethyl cellulose (HMHEC) and alkali-sensitive cleavable betaine ester surfactants have been studied by viscometry, 1H NMR, absorbance measurements, and birefringence determinations. Before the hydrolysis, the surfactants behaved as conventional nondegradable surfactants in terms of the effect on the viscosity of increasing surfactant concentration. As the surfactants were hydrolyzed, systems with time-dependent viscosity were obtained. The viscosity either decreased monotonically or went through a maximum as a function of time, depending on the initial surfactant concentration. Different surfactant chain lengths gave rise to different viscosity profiles. The rate of hydrolysis, and thus the time-dependency of the surfactant concentration, could be controlled by changing the pH of the solution.