Arbitrarily switchable multi-wavelength Yb-doped fiber lasers with phase-shifted long-period fiber grating

An arbitrarily switchable multi-wavelength Yb-doped fiber laser (YDFL) based on a phase-shifted long-period fiber grating (PS-LPFG) is proposed and demonstrated. The PS-LPFG, which was fabricated by a CO₂ laser under asymmetric exposure, acts as a spectral filter with anisotropic transmission spectrum at different states of polarization. The capability of arbitrary wavelength switching can be attributed to the combination of the polarization-dependent loss (PDL) of the PS-LPFG and the nonlinear polarization rotation (NPR) effect. The method suggests a new possibility to achieve even more wavelengths output with an all-fiber format, arbitrarily switchable and tunable capability in the Yb-doped fiber laser system in a simple, stable and well controlled manner.     

Frequency tuning and doubling in Yb-doped fiber lasers

A compact Yb-doped fiber laser (YDFL) based on a tunable fiber Bragg grating (FBG) with ～6 W output power and ～45 nm tuning around 1080 nm has been developed. The laser output power and its spectral width (～0.15 nm) do not change significantly at the tuning, while the FBG reflection coefficient increases with an increase in FBG compression. It has been shown that this increase is due to stress-induced changes in the FBG’s refractive-index modulation amplitude. Intracavity frequency doubling in the YDFL has also been performed. About 0.4 W of green radiation with tuning in the range 540–548 nm has been achieved with a KTP nonlinear crystal.     

Influences of ASE on the performances of Q-switched ytterbium-doped fiber lasers

The output characteristics of actively Q-switched ytterbium-doped fiber lasers (YDFL) are investigated in this paper. Our experimental results show that, the combined effect between the short switching time and the gain transient property of doped fiber causes the initial amplified spontaneous emission (ASE) power fluctuation, forming the multi-peak structure in the output pulse for either ring or linear cavity Q-switched YDFL. The pulse buildup time decreases with the rising of the pump. Moreover, since the broad-band ASE generated in the YDF is very high, it may saturate the doped fiber once the switch has been opened, making it difficult to achieve Q-switched laser oscillation for both fiber lasers. By using ASE filter to suppress the initial ASE, the gain supplied by the YDF can be greatly enhanced, which can not only decrease the threshold, but also greatly decrease the duration, and enhance the peak power of the Q-switched laser pulse as well. By using such an ASE filter, the Q-switched laser pulse with the peak power of 40.7 W and the duration of 30 ns has been achieved for the linear cavity YDFL pumped with 160 mW.     

光纤激光泵浦MgO:PPLN高功率中波红外光参量振荡器

为实现高效率、高功率中波红外激光输出,研制基于MgO:PPLN晶体的中波红外光参量振荡器（OPO）,泵浦源为基于主振荡功率放大（MOPA）结构的线偏振掺Yb光纤激光器（YDFL）。实验结果表明:YDFL可实现最高79.1 W的1064.1 nm脉冲线偏振激光输出;在YDFL泵浦下,通过优化输出镜曲率半径和泵浦光束腰直径,该OPO实现最高9.15 W的3.754 μm脉冲激光输出,光光转换效率为11.57%,重复频率为300 kHz,脉冲宽度约为110 ns。     

滤波对8字腔掺铒光纤激光器锁模运转的影响

构建了基于损耗非对称非线性光学环镜的8字腔掺铒光纤锁模激光器,并讨论了腔内滤波带宽对腔内脉冲演化和激光器输出特性的影响.在非线性光学环镜中引入双向输出耦合器,耦合器和传输光纤位置的不对称产生非互易性,实现锁模运转.利用自制的可调谐滤波器实验研究了滤波带宽对激光器的影响.当滤波带宽为2.1 nm时,腔内脉冲的演化过程受滤波和孤子效应的共同作用,激光器顺时针和逆时针输出脉冲半高全宽分别为583.7fs和2.94 ps.随着滤波带宽增大,滤波的作用逐渐减弱,激光器两路输出脉冲参数逐渐接近,并接近傅里叶变换极限脉冲.当滤波带宽较大时,腔内脉冲的演化过程受增益谱和孤子效应的共同作用,激光器顺时针和逆时针输出脉冲均为变换极限脉冲,半高全宽约为440 fs.通过调节滤波器中心波长实现了对激光器输出脉冲光谱的连续调谐,调节范围大于30 nm.     

Multi-Wavelength Q-Switched Ytterbium-Doped Fiber Laser with Multi-Walled Carbon Nanotubes

We demonstrate a passively multi-wavelength Q-switched Ytterbium-doped fiber laser (YDFL) based on a multi-wall carbon nanotubes embedded in polyethylene oxide film as saturable absorber. The YDFL generates a stable multi-wavelength with spacing of 1.9 nm as the 980 nm pump power is fixed within 62. 4 mW and 78.0 mW. The repetition rate of the laser is tunable from 10.41 to 29.04 kHz by increasing the pump power from the threshold power of 62.4 mW to 78 mW. At 78 mW pump power, the maximum pulse energy of 38 nJ and the shortest pulse width of 8.87 µs are obtained.     

8字形腔波长可调谐锁模脉冲光纤激光器

采用非线性光纤环形镜加脉冲锁模技术及可调谐光纤光栅滤波器,对8字形腔被动锁模掺铒光纤激光器进行了波长可调谐输出的实验研究.在EDFA抽运光功率一定的情况下,通过调节偏振控制器和可调谐光纤光栅滤波器,获得了光谱稳定、重复频率1.1 MHz、输出功率起伏小于0.8 dBm、中心波长在1 548~1 570 nm内连续可调的短脉冲输出.该激光器可实现自启动锁模,且长时间稳定工作无需任何调整.     

基于光纤中超短脉冲非线性传输机理与特定光谱选择技术的多波长飞秒激光的产生

高集成、高可靠性宽调谐飞秒激光源在超快光谱学、量子光学及生物成像等研究与应用领域具有重要价值.如在生物多光子显微成像中,具有适中能量的宽调谐飞秒激光源不仅可满足多种生物组织荧光激发所需的峰值功率与激发波长,而且也可以显著提升非线性荧光产生效率、成像分辨率以及增大成像穿透深度.采用自主研发的高可靠性全保偏光纤飞秒激光器作为抽运源,基于低色散光纤中高峰值功率飞秒激光脉冲非线性传输引起的光谱加宽机制,本文开展了多波长全光纤飞秒激光产生技术研究.通过采用中心波长在980, 1000,1050, 1070与1100 nm的带通滤波片选择性地对单模光纤输出光谱中最左边与最右边光谱旁瓣进行滤波,在上述中心波长处分别可获得203, 195, 196, 187与194 fs的激光输出.本文提出的基于全光纤飞秒激光脉冲在单模光纤中非线性传输引起的光谱加宽机制与特定光谱选择技术的实验方案为高集成、高可靠性宽调谐飞秒激光源的实现提供了新的研究途径.     

输出平均功率大于2W的高功率、包层抽运、超短脉冲铒镱共掺光纤激光器

采用主振荡功率放大的方式，研制成功集宽带波长连续可调谐、带宽内输出功率谱均衡、高重复频率和高功率性能于一体的超短脉冲包层抽运铒镱共掺光纤激光器.将优化主振荡器和功率放大器的腔结构与掺铒光纤的饱和增益特性结合起来，实现了1535nm—1570nm(35nm带宽)的输出功率均衡的波长连续可调谐激光输出，在带宽内激光功率的最大波动仅为0.5dBm；带宽内平均输出功率大于2W、脉冲重复频率大于10GHz、脉冲宽度小于30ps.该激光器具有综合性能指标先进、结构简单、全光纤化、使用方便等优点. 关键词： 光纤激光器 包层抽运 短脉冲 高重复频率     

Tunable passively Q-switched ytterbium-doped fiber laser using MoWS2/rGO nanocomposite saturable absorber

We demonstrated a tunable Q-switched ytterbium-doped fiber laser (YDFL) using MoWS₂/rGO nanocomposite as passive saturable absorber. Further, the Mo_1?xW_xS₂/rGO nanosheets, with x proportion of 0.2, are synthesized using hydrothermal exfoliation technique. The proposed nanocomposite-PVA based thin film is fabricated by mixing the MoWS₂/rGO nanosheets with polyvinyl alcohol (PVA). The fabricated thin film is sandwiched between two fiber ferrules to realize the proposed saturable absorber (SA). Further, the proposed MoWS₂/rGO-PVA based thin film SA exhibits a fast relaxation time and a high damage threshold which are suitable to realize a Q-switched pulsed laser with a tunable wavelength range of 10?nm that extends from 1028?nm to 1038?nm. For the highest pump power of 267.4?mW, the generated Q-switched pulses exhibit a narrow pulse width of 1.22 μs, the pulse repetition rate of 90.4?kHz, the highest pulse energy of 2.13?nJ and its corresponding average power of 0.193?mW. To the best of author’s knowledge, this is the first realization of a tunable Q-switching fiber laser in a 1?μm wavelength using MoWS₂/rGO nanocomposite saturable absorber.     

All-fiber ring-cavity based frequency swept laser source for frequency domain OCT

<正>We develop a high-speed tunable,quasi-continuous-wave laser source for frequency domain(FD) optical coherence tomography(OCT).The laser resonance is realized within a unidirectional all-fiber ring cavity consisting of a fiber coupler,two fiber isolators,a semiconductor optical amplifier(SOA),and a fiber FabryPerot tunable filter(FFP-TF) for frequency tuning.Light output from the coupler is further amplified and spectral shaped by a booster SOA terminated at both ends with two isolators.The developed laser source provides up to 8000 sweeps per second over a full-width wavelength tuning range of 120 nm at center wavelength of 1320 nm with an average power of 9 mW,yielding an axial resolution of 13.6μm in air and a maximum sensitivity of about 112 dB for OCT imaging.The instantaneous linewidth is about 0.08 nm,enabling OCT imaging over an axial range of 3.4 mm in air.For optimization consideration based on this custom-built swept laser,experimental study on imaging quality relevant parameters of the swept laser with sine and ramp driving waveforms to the FFP-TF is conducted,and investigation of the swept laser on the cavity length is done.Implementing the laser source in our established swept source based OCT(SS-OCT) system,real-time structural imaging of biological tissue is demonstrated.     

Generation of multi-wavelength square pulses in the dissipative soliton resonance regime by a Yb-doped fiber laser

Multi-wavelength square pulses are generated in the dissipative soliton resonance(DSR) regime by a Yb-doped fiber laser(YDFL) with a long cavity configuration. The spectral filter effect provided by a passive fiber with low-stress birefringence facilitates the establishment of multi-wavelength operation. Through appropriate control of the cavity parameters,a multi-wavelength DSR pulse can be generated in single-and dual-waveband regions. When the multi-wavelength DSR works in the 1038 nm waveband, the pulse duration can broaden from 2 ns to 37.7 ns. The maximum intra-cavity pulse energy is 152.7 nJ. When the DSR works in the 1038 nm and 1080 nm wavebands, the pulse duration can be tuned from2.3 ns to 10.5 ns with rising pump power. The emergence of the 1080 nm waveband is attributed to the stimulated Raman scattering(SRS) effect. Our work might help a deeper insight to be gained into DSR pulses in all-normal-dispersion YDFLs.     

均衡功率的超宽带可调谐掺铒光纤激光器

报道了一种功率均衡的超宽带可调谐掺铒光纤激光器.该激光器采用窄线宽可调谐FP滤波器、掺铒光纤、波分复用器和耦合器构成光纤环形腔激光器，并通过部分反馈光功率自动控制，对输出激光功率进行均衡.实现了87 nm带宽（1525~1612 nm）范围内，输出激光功率波动小于0.2 dB的均衡结果.输出激光3 dB线宽为0.26 nm，边模抑制比大于55 dB.     

Review on recent progress on Yb-doped fiber laser in a variety of oscillation spectral ranges

We present review on recent progress on high power Yb-doped fiber laser in a variety of oscillation spectral ranges. According to Kurkov (Laser Phys. Lett. 2006), the oscillation spectral range of YDFLs can be divided into three bands: convenient (C-band), short (S-band), and long (L-band). For the C-band YDFL, tandem-pumped high power radiation by using 1018 nm fiber laser or 1030 nm thin-disk laser is reviewed. For the S-band YDFL, three mainly technical solutions, i.e., special designed fiber, the employment of photonic crystal fiber (PCF), and tandem pumping using 930 nm Nd-doped fiber laser are presented. For the L-band laser, active heating or self-heating the active fiber can help the long-wavelength oscillation. Fiber Raman laser or amplifier can also boost the power of L-band YDFL up. Some discussions and prospective predictions are proposed at the end of this paper.     

Erbium-doped CW and Q-switched fiber ring laser with fiber grating Michelson interferometer

The band-pass characteristic of fiber grating Michelson interferometer is analyzed, which acts as bothband-pass filter and Q-switch. An erbium-doped fiber ring laser based on fiber grating Michelsoninterferometer is implemented for producing single longitudinal mode CW operation with 5 MHz spectrallinewidth and up to 6 mW output power. In Q-switched operation, stable fiber laser output pulses withrepetition rate of 800 Hz, pulse width of 0.6 μs, average power of 1.8 mW and peak power of 3.4 W aredemonstrated. The peak power and average power of the Q-switched pulses are varied with the repetitionrate.     

Frequency doubling of Yb-doped fiber laser to 515 nm

Operation of Yb-doped fiber laser (YDFL) at short wavelengths (about 1030 nm) is known to be possible with relatively short active fibers. Frequency doubling of such a laser is studied. It is shown that, in contrast to conventional YDFLs, operating around 1080 nm, the short-wavelength YDFL does not exhibit significant spectral broadening induced by nonlinear effects. Thus, the generated spectrum remains narrower than the FBG reflection profile, which allows an almost twofold intracavity intensity enhancement. Consequently, the second harmonic generation in the KTP crystal placed inside the YDFL cavity appears more effective than the generation in the single-pass scheme by an order of magnitude. An output power of about 0.4 W at a wavelength of 515 nm is demonstrated.     

Fourier domain mode locking pulse fiber laser

A novel pulse fiber laser is proposed based on the modulation of the lasing wavelength. Different from conventional amplitude or phase modulated mode-locking fiber lasers, the proposed fiber laser is with a so-called Fourier domain mode locking (FDML) operation (i.e., the cavity round-trip time of the optical pulse should match the period that the open time window of the tunable filter appears for the lasing wavelength or its harmonics). An FDML pulse fiber laser with a cavity round-trip frequency of 19.46 kHz is demonstrated and optical pulses with repetition rate of 19.46 kHz are achieved when the wavelength modulation frequency is 9.73 kHz.     

高重复频率、单模纳秒脉冲全光纤激光器

报道了一种基于主振荡放大技术的全光纤脉冲激光器.种子激光器使用直接调制的单纵模半导体激光器,其输出波长为1 063.8 nm,重复频率100 kHz~10 MHz连续可调谐,光纤放大器采用了多级放大器级联的方法.在重复频率100 kHz、脉冲宽度5 ns时,激光器获得了平均功率为1.2 W,峰值功率为2.4 kW的单横模激光脉冲输出.     

宽光谱全正色散锁模掺镱光纤激光器

介绍了一种全正色散宽光谱被动锁模掺镱光纤激光器,利用非线性偏振旋转技术实现全正色散掺镱光纤激光器的被动锁模.当泵浦功率输出为500mW时,激光脉冲输出功率大于139mW,重复频率约为28.1MHz,脉冲宽度为3.8ps.为了进一步研究全正色散光纤激光器的宽光谱输出特性,在腔内熔接50m单模光纤,同时去除双折射滤波片,在泵浦功率为500mW时,观察到稳定锁模单脉冲耗散孤子,光谱范围为1 005~1 140nm,输出激光脉冲最大平均功率为90mW,重复频率为3.58MHz,脉冲宽度为519ps.     

基于高双折射光子晶体光纤与光纤环的超宽带可调谐微波光子滤波器

提出一种基于高双折射光子晶体光纤与光纤环的超宽带可调谐微波光子滤波器.以多波长光纤激光器作为光源,向高双折射光子晶体光纤内填充温敏液体,通过改变填充温敏液体的温度,高双折射光子晶体光纤可具有不同的双折射,得到不同波长间隔的激光,从而使微波光子滤波器具有不同的自由频谱范围.当温度的变化范围为20~80℃时,仿真测得微波光子滤波器自由频谱的变化范围为2.49~39.9GHz.引入光纤环构建级联型微波光子滤波器,滤波器的主旁瓣抑制比可提高到33.6dB,Q值可达到499,提高了滤波器的频率选择性.