35MeV/uAr离子辐照聚酯膜引起的效应研究

采用多种手段研究了 35Me V/u的 Ar离子辐照聚酯 (PET)膜产生的微观结构变化 .结果表明 ,辐照使聚酯的化学键断裂并产生了炔端不饱和基团和自由基 .断键主要发生在乙二醇残留物、苯环的对位和酯的 C— O键上 .随着吸收剂量的增加 ,材料的结晶度逐渐降低 ,由原始的41 .7%减至最高辐照量时的 1 5.0 % .研究发现 ,聚脂的非晶化转变截面与电子能损呈线性关系 ;断键和非晶化效应主要取决于样品的吸收剂量 ,并存在一个约 4.0 MGy的阈值.Stacked polyethylene terephthalate films were irradiated with 35 MeV/u Ar ions at room temperature. The ion induced effects were studied by ultraviolet visible spectrometer, Fourier transform infrared spectroscopy, X ray diffractometer, X ray photoelectron spectroscopy, electron spin resonance spectroscopy and differential scanning calorimetry. Bond breaking and the formation of alkyne end groups and free radicals were observed. The bond breaking processes occurred mainly...     

22 MeV/u的Fe离子在PET 膜中引起的辐照效应研究

用能量为22 MeV/u的 Fe离子在室温和真空条件下辐照了多层堆叠的半晶质聚酯膜, 采用傅里叶转换红外吸收光谱、 紫外/可见吸收光谱 和X射线衍射技术分析测量了辐照后聚酯膜的微观结构所发生的变化, 详细研究了分子结构的变化和非晶化转变与离子剂量、 离子在样品中的平均电子能损以及吸收剂量的依赖关系． 分析结果表明: 辐照导致化学键的断裂、 新化学键的形成和非晶化转变． 非晶化效应和化学键的断裂随离子剂量和电子能损的增加而增大, 但变化的总量仅依赖于总的吸收剂量, 表明在所涉及的能损范围里, 辐照产生的变化与辐照离子的种类和能量没有直接的关系, 而只决定于材料对辐照离子能量的吸收程度． Semicrystalline polyethylene terephthalate (PET) film stacks were irradiated with 22 MeV/u Fe ions at room temperature under vacuum. Ion beam induced microscopic structural modifications and amorphous transformation were investigated by means of Fourier transform infrared spectrosocopy (FTIR), ultraviolet visible absorption spectrosocopy (UV/Vis) and X ray diffractometer (XRD). It was found that irradiation induces bond breaking, formation of new free radiculs and amorphous transformation. These effects were found to depend on ion fluence , the electronic energy loss and aborbed dose. The creation of alkyne groups was found only at the aborbed dose higher than 5.0 MGy.     

高能Ar离子辐照PET引起的光吸收变化研究

采用紫外–可见光吸收技术分析和研究了35MeV/uAr离子辐照聚酯膜引起的光吸收改性.结果表明,Ar离子轰击聚酯膜时引起了碳键的共轭体系形成,从而导致了紫外–可见光区域中光吸收明显增加,光吸收增加的幅度依赖于离子的照射剂量、离子在样品中的平均电子能量损失以及光的波长,剂量越高,电子能损越大,光吸收增幅越大;而光的波长越长,光吸收的增加则越不明显.利用测量到的光吸收曲线,同时还定量地研究了各种辐照条件下聚酯膜的光能隙和碳原子团的尺寸.     

2.1GeV?Kr离子在聚碳酸酯膜中引起的辐照效应研究

用傅立叶变换红外光(FTIR)谱仪和紫外/可见光(UV/VIS)谱仪研究了2.1GeVKr离子在聚碳酸酯(PC)膜中产生的效应.研究结果表明,在高能Kr离子辐照下,PC膜中发生了断键、断链和键的重组,炔基的出现是键的断裂和重组的结果.这些效应与辐照剂量和电子能损有关.辐照也使PC膜中发生了从氢化非晶态碳向非晶态碳的转变,在UV/VIS中,波长为380,450和500nm处的相对吸光度随能量沉积密度的增加近似按线性变化.     

辐照导致硼硅酸盐玻璃机械性能变化

为了模拟研究高放废物玻璃固化体在处置过程中因辐照导致的机械性能变化,本文采用5 MeV Xe离子和1.2 MeV电子辐照硼硅酸盐玻璃,利用纳米压痕技术表征了辐照前后样品的硬度和模量,并利用傅里叶变换衰减全反射红外光谱测试,研究了辐照导致玻璃机械性能变化的微观机理.结果表明:当能量沉积达到6.6×10~(21)keV/cm~3时,Xe离子辐照样品的硬度和模量下降都达到饱和,其中硬度下降约24%,模量下降约7.4%;电子辐照后样品的硬度和模量也有轻微下降,但在实验所用剂量范围内硬度和模量下降未出现饱和现象,当吸收剂量达到最大值(1×10~9 Gy)时,硬度和模量分别下降约4.7%和2.9%.分析表明:Xe离子辐照后样品的恢复阻力增大,韧性提高,整体机械性能提升,而电子辐照后样品的机械性能无明显变化.研究结果证明了离子辐照导致玻璃机械性能变化的主要因素是离子在样品中的核能量沉积.     

低速高电荷态重离子辐照的GaN晶体表面X射线光电子能谱研究

利用低速高电荷态Xeq+和Pbq+离子对在蓝宝石衬底上生长的GaN晶体膜样品进行辐照,并利用X射线光电子能谱(XPS)对样品表面化学组成和元素化合态进行了分析.结果表明,高电荷态离子对样品表面有显著的刻蚀作用;经高电荷态离子辐照的GaN样品表面氮元素贫乏而镓元素富集;随着入射离子剂量和所携带电荷数的增大,Ga—Ga键相对含量增大;辐照后,GaN样品中Ga—Ga键对应的Ga3d5/2电子的束缚能偏小,晶格损伤使内层轨道电子束缚能向低端方向偏移.     

高能氩离子在聚苯乙烯中的电子能损效应研究

用1.4GeV氢离子对多层堆叠的厚约53m的聚苯乙烯薄膜在室温和真空条件下进行了辐照;对辐照后的样品进行了从红外到紫外的光吸收测量.测量结果显示,材料经高能红离子辐照后发生化学降解,降解过程强烈依赖于电子能损;在能量沉积密度很高的径迹芯中,分子主链和苯环均遭到破坏;在电子能损高于0.77keV/nm时有炔基产生.     

电子束辐照对聚碳硅烷结构与热解性能的影响

在惰性气氛下,用电子束对聚碳硅烷(PCS)进行辐照改性。利用傅里叶变换红外光谱分析、凝胶含量测定以及热重-气相色谱-质谱连用技术对不同剂量改性的PCS进行了分析表征,研究了辐照剂量对PCS结构与热解性能的影响。结果表明,电子束辐照作用使PCS样品中大量Si—H键和C—H键发生断裂,形成了以Si—C—Si为骨架的三维网状凝胶产物,当辐照剂量高于3MGy时,PCS的凝胶化程度随辐照剂量的增加而明显变大。热重分析表明,电子束辐照有利于提高PCS的热稳定性,其初始失重温度和陶瓷化产率都会随辐照剂量的增加而升高,其中,经20 MGy辐照后的PCS样品的陶瓷化产率可达87%。此外,对于400℃预处理的PCS样品,在相同吸收剂量下,样品的凝胶质量分数、初始失重温度和最终陶瓷化产率都较未处理的高。     

离子辐照对聚苯乙烯低温导电特性的影响

室温下用3MeV的硅离子对聚苯乙烯(PS)进行辐照,对辐照后的样品在室温至液氮温度范围的导电特性进行了测量.结果表明,当辐照剂量在1×1012cm-2附近,PS的室温电阻发生突变.随着温度的降低,PS电阻增大,在低辐照剂量下,电阻在155K附近急剧增加.对于高辐射剂量样品,在较高的温度下呈现热激活导电,在低温下电子通过隧穿传导.分析认为,PS电阻随温度的变化是由于不同剂量辐照离子在聚合物中形成的对电子传导有贡献的导电中心密度不同.通过拟合样品的渗流临界特性,分析了样品电阻随辐照剂量的变化 关键词： 聚苯乙烯 硅离子辐照 低温导电     

高能Pb离子辐照注碳SiO2的红外谱研究

室温下，先用120keV的C离子注入二氧化硅薄膜样品至剂量2.0×1017、5.0×1017或8.6×1017ions/cm2，再用950MeV的Pb离子分别辐照至剂量5.0×1011、1.0×1012或3.8×1012 ions/cm2，然后测量样品的傅里叶变换红外(FTIR)光谱. 通过分析测量得到的傅里叶变换红外谱，发现Pb离子辐照在注碳SiO₂样品中可引起大量的Si－C和Si (C)－O－C等化学键的形成，大剂量Pb离子辐照可在大剂量注碳的SiO₂中产生分子CO₂. 大量的Si－C键的存在和分子CO₂的形成，预示着高能Pb离子辐照在注碳SiO₂样品中有可能形成了纳米Si团簇和/或SiC晶粒.     

Consequences of electronic excitations in CoFe1.90Dy0.10O4

Present work reports the irradiation induced effects in Dy³⁺ doped cobalt ferrite nanoparticles in the regime of dominant electronic excitation processes induced by 100 MeV O⁷⁺ ion irradiation. Irradiation leads to the deterioration of crystalline phase as envisaged by X-ray diffraction. Crystallite size decreases with the increase of irradiation fluence. Disappearance of certain bands in Raman spectra at higher fluence of irradiation confirms the crystalline disorder induced by electronic excitations. Fourier transform infrared spectra show onset of cation migration from tetrahedral site to octahedral site and vice versa. X-ray absorption fine structure measurements depict the preservation of valence state of metal ions after irradiation. These measurements further infer bond breaking process in irradiated materials. Magnetic measurements carried out on these materials indicate slight increase of saturation magnetization at room temperature followed by the decrease of coercive field. Obtained results are discussed on the basis of appropriate mechanism.     

Conductivity of irradiated Kapton in relation to energy loss of ions and electrons

Abstract

We have studied the effects of 2.5 MeV electron irradiation and ion (C, N, F, Si and Kr) bombardment on the electrical conductivity of a polyimide (Kapton-H) with ion energies ranging between 320 keV (N) and 1.25 GeV (Kr). In this wide range of situations we have tried to sort out the respective effects of nuclear and electronic excitation energy losses.

For all ion irradiation the conductivity is found to scale with the electronic excitation absorbed dose: i.e. a power law of conductivity versus absorbed dose with an exponent around 9 is observed. At a given absorbed dose (in Gray units) the efficiency of each ion to enhance conductivity is found to be proportional to the electronic energy loss; electrons are much less efficient than ions and thus collective excitations are required to achieve this process.

The nuclear energy loss can perhaps play some role at conductivities higher than 100 Ω^?1 m^?1, but its effects are negligible in the range explored here.     

聚合物材料的快重离子辐照效应

简要介绍了快重离子辐照损伤的特点,通过与低电离辐射粒子辐照在聚合物材料中产生的效应的类比论述了快重离子辐照在聚合物材料中产生的效应及其研究现状 ,并结合快重离子辐照效应的应用展望了该领域未来的发展.The irradiation effects in polymers induced by swift heavy ions were reviewed in comparison with that induced by low ionization particles based on the characteristics of swift heavy ion irradiations. It is shown that bond breaking and cross linking, gas releasing, amorphization and carbonization of polymers depend strongly on the electronic energy loss. Besides special effects such as alkynes production, can be induced under swift heavy ion irradiation. The perspectives...     

25 MeV/u Kr辐照下PET薄膜的损伤机制研究

通过25 MeV/u 86 Kr离子辐照叠层结晶聚对苯二甲酸乙二醇酯膜（PET）, 在不同的电子能损（3.40-7.25 keV/nm）和离子注量(5×1011----3×1012 ions/cm2)辐照条件下, 对Kr离子在PET中引起的辐照损伤效应进行了研究。借助傅里叶变换红外光谱分析,通过对样品的红外吸收峰进行扣除基底后的Lorentz拟合,分析了与主要官能团对应的吸收峰强度的变化趋势, 研究了化学结构与组分在重离子辐照下的变化规律; 利用X射线衍射光谱仪测量, 研究了Kr离子在PET潜径迹中引起的非晶化过程,并通过对吸光度和非晶化强度随离子注量的指数衰减规律的分析, 获得了不同电子能损离子辐照PET时主要官能团的损伤截面和非晶化截面及对应的潜径迹半径。 At room temperature, polyethylene terephthalate(PET) foil stacks were irradiated by 25 MeV/u Kr ions in the electronic stopping power range(3.3--7.66 keV/nm) and the fluence range from 5×1011 to 3×1012 ions/cm2. The behaviour of the main function groups with fluence and electronic stopping power were studied by using Fourier transform infrared(FTIR) spectroscopy, the degradation of the function group was investigated with the Lorentz fitting subtracted baseline. The amorphous processes in the latent tracks of PET were studied by X ray diffraction(XRD) measurements. The Kr ion induced degradation cross section and amorphisation cross sections(radii) for different electronic energy loss were acquired from the experimental data(FT IR and XRD) by exponential decay function respectively.      

Formation of periodic structures by surface treatments of polyamide fiber: Part I. UV excimer laser irradiation

The processes of UV excimer laser irradiation (both high- and low-fluence) of polyamide fiber were systemically studied, including the surface temperature of the material during the treatment and possible mechanisms for the structure formation. The fluence applied in the high-fluence laser irradiation was above the ablation threshold of the material. The ablation of polymer can be described on the basis of photo-thermal bond breaking within the bulk material. The fluence applied in the low-fluence laser irradiation was far below the ablation threshold of the material. The development of low-fluence laser-induced structures is closely related to the absorption coefficient of the material, the laser fluence used, the polarization of the laser beam, the angle of incidence, and the number of laser pulses applied.     

高能离子梯度多剂量辐照4H-SiC的微结构及硬度变化研究

为探讨高温高能离子辐照碳化硅后的结构和力学性能随剂量的变化,应用拉曼光谱和纳米压痕技术研究了122 MeV的²⁰Ne⁴⁺离子梯度多剂量辐照后的4H-SiC。研究表明,SiC的相对拉曼强度随剂量的增大呈指数规律下降,并出现了代表无序化Si-C键和同核Si-Si键的散射峰。基于DI/DS模型的初步拟合表明,在低剂量范围内扩展缺陷簇是引起SiC无序化的主要因素,高剂量范围内的无序化则是由离子直接碰撞过程的非晶化和扩展缺陷簇共同引起。辐照后的SiC硬度取决于位错钉扎和共价键断裂的共同作用,在0～4.00 dpa之间硬度随剂量增大而增大,在4.00～8.05 dpa之间硬度随剂量增大而减小,剂量在8.05 dpa时,硬度相比于未辐照区域略高,此时共价键断裂和位错钉扎达到平衡。     

The loss of boron in ultra-shallow boron implanted Si under heavy ion irradiation

Heavy ion impact has been known to cause a loss of light elements from the near-surface region of the irradiated sample. One of the possible approaches to a better understanding of the processes responsible for the release of specific elements is to irradiate shallow-implanted samples, which exhibit a well-known depth distribution of the implanted species. In this work, the samples studied were produced by implantation of Si<1 0 0>wafers with ¹¹B at implantation energies of 250 and 500 eV and fluence of 1.0×10¹⁵ atoms/cm ². Elastic Recoil Detection Analysis was applied to monitor the remnant boron fluence in the sample. Irradiation of the samples by a 14.2 MeV ¹⁹F ⁴⁺ beam resulted in a slow decrease of boron remnant fluence with initial loss rates of the order of 0.05 B atom per impact ion. Under irradiation with 12 MeV ³²S ³⁺ ions, the remnant boron fluence in Si decreased exponentially with a much faster loss rate of boron and became constant after a certain heavy ion irradiation dose. A simple model, which assumes a finite desorption range and corresponding depletion of the near-surface region, was used to describe the observations. The depletion depths under the given irradiation conditions were calculated from the measured data.