The surface properties of ionomers based on styrene-co-acrylic acid copolymers

The surface properties of styrene-co-acrylic acid copolymers and of the obtained ionomers containing alkali metal ions, before and after UV-irradiation, were investigated by the measurements of water contact angles and ATR-FTIR spectroscopy.It was examined, how the content and nature of the alkali metal introduced into the initial copolymer influences the water contact angle, surface free energy and its components, polar and dispersive.It was ascertained that the water contact angle, surface free energy and its components depend on the content of introduced acid or salt. These values were practically independent of the nature of the alkali metal introduced into the copolymer. However, more considerable changes were observed for the ionomers containing sodium ions.The research has indicated that UV-irradiation causes the increase in surface hydrophilicity of the investigated ionomers.     

Changes in wetting and energetic properties of glass caused by deposition of different lipid layers

An investigation of wetting and energetic properties of different lipid layers deposited on the glass surface was carried out by contact angles measurements and determination of the apparent surface free energy. The topography of the lipid layers was also determined with the help of atomic force microscopy (AFM). Two synthetic phospholipids were chosen for these studies, having the same phosphatidylcholine headgroup bound to the apolar part composed either by two saturated chains (1,2-dipalmitoyl-sn-glycero-3-phospshocholine - DPPC) or two unsaturated chains (1,2-dioleoyl-sn-glycero-3-phosphocholine - DOPC) and one lipid (1,2,3-trihexadecanoyl-sn-glycerol - tripalmitoylglycerol - TPG). The lipid layers, from the 1st to the 5th statistical monolayer, were deposited on the glass surface from chloroform solutions by spreading.The apparent surface free energy of the deposited layers was determined by contact angles measurements (advancing and receding) for three probe liquids (diiodomethane, water, and formamide), and then two concepts of interfacial interactions were applied. In the contact angle hysteresis approach (CAH) the apparent total surface free energy was calculated from the advancing and receding contact angles and surface tension of probe liquids. In the Lifshitz-van der Waals/acid-base approach (LWAB) the total surface free energy was calculated from the determined components of the energy, which were obtained from the advancing contact angles of the probe liquids only. Comparison of the results obtained by two approaches provided more information about the changes in the hydrophobicity/hydrophilicity of the layers depending on the number of monolayers and kind of the lipid deposited on the glass surface.It was found that the most visible changes in the surface free energy took place for the first two statistical monolayers irrespectively of the kind of the lipid used. Additionally, in all cases periodic oscillations from layer-to-layer in the lipid surface free energy were observed. The changes in the surface free energy correlated with those in the topography and roughness of lipid layers.     

Surface free energy of non-stick coatings deposited using closed field unbalanced magnetron sputter ion plating

Semiconductor IC packaging molding dies require wear resistance, corrosion resistance and non-sticking (with a low surface free energy). The molding releasing capability and performance are directly associated with the surface free energy between the coating and product material. The serious sticking problem reduces productivity and reliability. Depositing TiN, TiMoS, ZrN, CrC, CrN, NiCr, NiCrN, CrTiAlN and CrNiTiAlN coatings using closed field unbalanced magnetron sputter ion plating, and characterizing their surface free energy are the main object in developing a non-stick coating system for semiconductor IC molding tools. The contact angle of water, diiodomethane and ethylene glycol on the coated surfaces were measured at temperature in 20 °C using a Dataphysics OCA-20 contact angle analyzer. The surface free energy of the coatings and their components (dispersion and polar) were calculated using the Owens-Wendt geometric mean approach. The surface roughness was investigated by atomic force microscopy (AFM). The adhesion force of these coatings was measured using direct tensile pull-off test apparatus. The experimental results showed that NiCrN, CrN and NiCrTiAlN coatings outperformed TiN, ZrN, NiCr, CiTiAlN, CrC and TiMoS coatings in terms of non-sticking, and thus have the potential as working layers for injection molding industrial equipment, especially in semiconductor IC packaging molding applications.     

Aluminum pigment encapsulated by in situ copolymerization of styrene and maleic acid

To improve its anticorrosion property, aluminum pigment was encapsulated by in situ copolymerization of styrene (St) and maleic acid (MA). It was found that the conversion of monomers (C), the percentage of grafting (PG) and the grafting efficiency (GE) could attain 92%, 12%, 25%, respectively, when m(BPO)/m(St + MA) = 10% and m(St + MA)/m(Al) = 10%. The optimum condition for protection factor was studied according to an orthogonal testing. When m(St + MA)/m(Al) was 20%, the encapsulated aluminum pigment simultaneously showed good anticorrosion property and luster. FTIR, SEM and particle size analysis indicated that aluminum pigment had been successfully encapsulated with styrene-maleic acid copolymer by in situ copolymerization, which remarkably improved its anticorrosion property and the chelate complex formed between SMA and Al(III) was possibly the actual corrosion inhibitor.     

Graft copolymerization of acrylic acid onto polyamide fibers

The grafting of acrylic acid (AA) monomer (CH₂CHCOOH) on polyamide 6.6 monofilaments (PA 6.6) using benzoyl peroxide (BPO) as initiator was carried out in order to enhance the hydrophilic nature of fibers. The grafting rate depends on the AA concentration, the BPO concentration, the time and the temperature of reaction.The best conditions for optimum rate of grafting were obtained with a AA concentration of 0.5 M, a BPO concentration of 0.03 M, a reaction temperature of T = 85 °C and a reaction time of 120 mn.The fiber surface has been investigated by many experimental techniques of characterization such as Fourier transform infrared spectroscopy (FTIR), calorimetric analysis (DSC), scanning electron microscopy (SEM), and contact angle measurements.The effect of grafting of acrylic acid onto PA 6.6 fibers on their moisture and mechanical resistances was analyzed from water sorption and elongation at break measurements.The analysis of the experimental data shows clearly the efficiency of the grafting reaction used, leading to a significant increase of the hydrophilic character of the PA 6.6 surface.     

Surface modification of polyacrylonitrile film by anchoring conductive polyaniline and determination of uricase adsorption capacity and activity

Polyacrylonitrile (PAN) films were modified with chemical polymerization of conductive polyaniline (PANI) in the presence of potassium dichromate as an oxidizing agent. The effect of aniline concentration on the grafting efficiency and on the electrical surface resistance of PAN and (PAN/PANI)-1-3 composite film was investigated. The surface resistances of the conductive composite films were found to be between 6.32 and 0.97 kΩ/cm. As the amount of grafted PANI increased on the PAN films, the electrical resistance of composite film decreased. The PAN/PANI composite films were also characterized using SEM and FTIR. The changes in the surface properties of the films were characterized by contact angle measurements. As expected, the PAN, PAN/PANI and PAN/PANI-uricase immobilized films, exhibited different contact angle values and surface free energy due to different interactive functional groups of the films.The conductive films were well characterized and used for immobilization of uricase. The amount of adsorbed enzyme increases with the increase of surface concentration of grafted fibrous polyaniline polymer. The maximum amount of immobilized enzyme onto composite film containing 2.4% PANI was about 216 μg/cm² (i.e., PAN/PANI-3). The immobilized uricase was reused 24 times in batch wise assay in a day. Finally, the immobilized uricase enzyme system was successfully fabricated and applied to determine the uric acid level in human serum samples.     

Engineering of hydrophilic and plasmonic properties of Ag thin film by atom beam irradiation

Hydrophilic Ag nanostructures were synthesized by physical vapour deposition of 5 nm Ag thin films followed by irradiation with 1.5 keV Ar atoms. Optical absorbance measurements show a characteristic surface plasmon resonance absorption band in visible region. A blue-shift in absorbance from 532 to 450 nm is observed with increasing fluence from 1 × 10¹⁶ to 3 × 10¹⁶ atoms/cm². Atomic force microscopy was performed for the pristine and irradiated samples to study the surface morphology. The atom beam irradiation induced sputtering and surface diffusion lead to the formation of plasmonic surface. Rutherford backscattering spectroscopy of the pristine and irradiated film indicates that metal content in the film decreases with ion fluence, which is attributed to the sputtering of Ag by Ar atoms. The contact angle measurement demonstrates the possibility of engineering the hydrophilicity by atom beam irradiation.     

Surface free energy of CrNx films deposited using closed field unbalanced magnetron sputtering

CrN_x thin films have attracted much attention for semiconductor IC packaging molding dies and forming tools due to their excellent hardness, thermal stability and non-sticking properties (low surface free energy). However, few data has been published on the surface free energy (SFE) of CrN_x films at temperatures in the range 20-170 °C. In this study CrN_x thin films with CrN, Cr(N), Cr₂N (and mixture of these phases) were prepared using closed field unbalanced magnetron sputtering at a wide range of Cr⁺² emission intensity. The contact angles of water, di-iodomethane and ethylene glycol on the coated surfaces were measured at temperatures in the range 20-170 °C using a Dataphysics OCA-20 contact angle analyzer. The surface free energy of the CrN_x films and their components (e.g., dispersion, polar) were calculated using the Owens-Wendt geometric mean approach. The influences of CrN_x film surface roughness and microstructure on the surface free energy were investigated by atomic force microscopy (AFM) and X-ray diffraction (XRD), respectively. The experimental results showed that the lowest total SFE was obtained corresponding to CrN at temperature in 20 °C. This is lower than that of Cr(N), Cr₂N (and mixture of these phases). The total SFE, dispersive SFE and polar SFE of CrN_x films decreased with increasing surface temperature. The film roughness has an obvious effect on the SFE and there is tendency for the SFE to increase with increasing film surface roughness.     

The use of contact angle measurements to estimate the adhesion propensity of calcium carbonate to solid substrates in water

We have studied a series of solids using contact angle measurements; stainless steel, gold, aluminium, titanium nitride and PTFE that are frequently used in domestic water environments. It was found the influence of electron-donor (γ⁻) and electron-acceptor (γ⁺) free energies on material scaling rate was dominated by water wetting angles, providing materials exhibit an average roughness below 100 nm. The γ⁻ component had the greatest influence on theoretical adhesion, while γ^LW, (Lifshitz-van der Waals) γ⁺ and γ^AB (acid-base) had little effect. From the materials analysed, amorphous carbon coatings were least adhesive, while ‘kettle coating’ and highly roughened steel the most adhesive. The size and distribution of asperities also influenced the polar free energies and subsequent adhesion due to fluctuations in the wetting angle. The results obtained indicate works of adhesion can be used as a complementary technique with Lewis acid-base theory to deliver useful information about the propensity of scale to deposit on solids.     

Surface modification of a biomedical polyethylene terephthalate (PET) by air plasma

In this work, low-pressure air plasma has been used to improve polyethylene terephthalate (PET) surface properties for technical applications. Surface free energy values have been estimated using contact angle value for different exposure times and different test liquids. Surface composition and morphology of the films were analyzed by X-ray photoelectron spectroscopy (XPS) and atomic force microscopy (AFM). Surface topography changes related with the etching mechanism have been followed by weight loss study. The results show a considerable improvement in surface wettability and the surface free energy values even for short exposure times in the different discharge areas (discharge area, afterglow area and remote area), as observed by a remarkable decrease in contact angle values. Change of chemical composition made the polymer surfaces to be highly hydrophilic, which mainly depends on the increase in oxygen-containing groups. In addition to, the surface activation and AFM analyses show obvious changes in surface topography as a consequence of the plasma-etching mechanism.     

The influence of repellent coatings on surface free energy of glass plate and cotton fabric

The aim of this research was to determine the influence of chemical finishes on the surface properties of glass plate, considered as a model homogeneous smooth surface and cotton fabric as a non-ideal heterogeneous rough surface. Microscopic slides and 100% cotton fabric in plain weave were coated with fluorocarbon polymers (FCP), paraffin waxes with zirconium salts (PWZ), methylolmelamine derivatives (MMD), polysiloxanes with side alkyldimethylammonium groups (PSAAC) and aminofunctional polysiloxanes (AFPS). From the goniometer contact angle measurements of different liquids, the surface free energy of the coated glass plates was calculated according to approaches by Owens-Wendt-Kaelble, Wu, van Oss-Chaudhury-Good, and Li-Neumann-Kwok. The results showed that all the coatings decreased the surface free energy of the substrate, which was also influenced by the liquid combination and the theoretical approach used. In spite of the fact that the liquid contact angles were much higher on the coated fabric samples than on glass plates and resulted in the lower values of work of adhesion, a very good correlation between the coatings deposited on both substrates was obtained. The presence of repellent coatings FCP, PWZ and MMD converted the solid surface from polar to highly apolar by masking the functional groups of glass and cellulose. PSAAC and AFPS coatings did not decrease the solid surface free energy to such an extent as the former three coatings due to their monopolar character.     

Adsorption behavior of weak hydrophilic substances on low-energy surface in aqueous medium

Through the methods such as measurements of contact angle and surface tension, calculations of surface energy and interfacial interaction free energy, and four weak hydrophilic substances (WHS) were taken as research objects, some interesting conclusions were obtained as follow. In aqueous medium, the WHS give priority to adsorb on low-energy surface that is low polar or particularly non-polar. There is a clear corresponding relationship between the free energy and Lewis base component γ⁻ or the hydrophile index of low-energy surface, and the specific relationship is obtained. Finally, we find hydrophobic attractive force of the Lewis acid-base interaction is mainly responsible for the absorption of WHS on low-energy surface. In short, an initial insight into adsorption behavior of WHS on low-energy surface is demonstrated in this paper.     

Influence of phytic acid concentration on coating properties obtained by MAO treatment on magnesium alloys

Anodic coatings were prepared by microarc oxidation (MAO) on AZ91HP in a base solution of 10 g/L NaOH with and without the addition of 0-12 g/L phytic acid (C₆H₁₈O₂₄P₆). The influences of C₆H₁₈O₂₄P₆ and its concentration on the conductivity and breakdown voltage were studied. The morphologies and compositions of anodic coatings were determined by environmental scanning electron microscope (ESEM) and energy dispersive X-ray spectroscopy (EDX). Potentiodynamic polarization test was performed in 3.5 wt.% NaCl solution to evaluate the corrosion resistance of anodic coatings. The results showed that with the increase of C₆H₁₈O₂₄P₆ concentration, the solution conductivity decreased while the values of breakdown voltage increased. EDX analysis showed that the coatings formed in solutions with C₆H₁₈O₂₄P₆ addition contained Mg, Al, O, C, P and a trance of Na. The addition of C₆H₁₈O₂₄P₆ into the base solution was helpful in coating formation and the coatings formed in the solution containing 8 g/L C₆H₁₈O₂₄P₆ exhibited the best pore uniformity and corrosion resistance.     

Comparison of coating properties obtained by MAO on magnesium alloys in silicate and phytic acid electrolytes

Anodic coatings were prepared by using microarc oxidation (MAO) on AZ91HP in silicate containing solution (Si-solution) and phytic acid containing solution (P-solution), respectively. The influence of the electrolytes on coating structure, morphology and composition was studied by using X-ray diffraction (XRD), environmental scanning electron microscope (ESEM) and energy dispersive X-ray spectroscopy (EDX). Potentiodynamic polarization test and immersion test were employed to evaluate the corrosion resistance of anodic coatings. Different electrolytes caused the differences in the MAO process and coating properties. The breakdown voltage and the final voltage in P-solution were higher than those in Si-solution. The pore uniformity of anodic coatings obtained in Si-solution (Si-film) was worse than that in P-solution (P-film). XRD analyses indicated that Si-film was amorphous, while P-film consisted of MgO. The corrosion resistance of the sample coated with P-film was better than that with Si-film.     

Structural, compositional, thermal resistant and hydro-oleophobic properties of fluorine based block-co-polymer films on quartz substrates by wet chemical process

Crack free and smooth surfaces of poly [4,5-difluoro 2,2-bis (trifluoromethyl)-(1,3 dioxole)-co-tetrafluoroethylene] (TFE-co-TFD) thin films have been deposited by wet chemical dip coating technique on polished quartz and glass slide substrates. The deposited films have been subjected to annealing at different temperatures ranging from 100 to 500 °C for 1 h in argon atmosphere. The elemental composition of the as-deposited (xerogel) thin film as well as film annealed at 400 °C was measured by X-ray photoelectron spectroscopy and observed that there was no change in the composition of the film. X-ray diffraction pattern revealed the amorphous behaviour of both as-deposited and film annealed at 400 °C. Surface morphology and elemental composition of the films have been examined by employing scanning electron microscopy attached with energy dispersive X-ray analyser, respectively. It was found that as the annealing temperature increased from 100 to 400 °C, nano-hemisphere-like structures have been grown, which in turn has shown increase in the water contact angle from 122^o to 148^o and oil (peanut) contact angle from 85° to 96°. No change in the water contact angle (122°) has been observed when the films deposited at room temperature were heated in air from 30 to 80 °C as well as exposed to steam for 8 days for 8 h/day indicating thermal stability of the film.     

Surface recombination probabilities of H on stainless steel, a-Si:H and oxidized silicon determined by threshold ionization mass spectrometry in H2 RF discharges

H atom densities are measured by threshold ionization mass spectrometry in a H₂ parallel-plate RF discharge. Variations of H density near the surface in steady-state discharge conditions reveal different surface loss probabilities γ on stainless steel, hydrogenated amorphous silicon (a-Si:H) and oxidized silicon. Absolute γ values are obtained from time-resolved H density measurements in afterglow. The etching probability of Si per H atom incident on a-Si:H is also derived by monitoring SiH₄ partial pressure and SiH(A²Δ) optical emission.     

Surface structure analysis based on the exclusive use of the specular LEED spot – a theoretical study

The exclusive use of the specularly reflected beam (the (0,0) spot) may be a more practical way of collecting data for a LEED I–V structure analysis under certain experimental conditions. In this paper we discuss the special properties of the (0,0) spot intensity and test its sensitivity towards structural changes for the model system CO/Ni(1 1 1) within the framework of a R factor analysis. It is found that the (0,0) spot can, indeed, be used for a reliable structure determination if the energy range is increased by collecting data at different polar and azimuthal angles of incidence. The R factor contrast is, however, reduced with respect to a conventional LEED I–V analysis.