Evaluation of fritless solid‐phase extraction coupled on‐line with capillary electrophoresis‐mass spectrometry for the analysis of opioid peptides in cerebrospinal fluid

Fritless SPE on‐line coupled to CE with UV and MS detection (SPE‐CE‐UV and SPE‐CE‐MS) was evaluated for the analysis of opioid peptides. A microcartridge of 150 μm id was packed with a C₁₈ sorbent (particle size > 50 μm), which was retained between a short inlet capillary and a separation capillary (50 μm id). Several experimental parameters were optimized by SPE‐CE‐UV using solutions of dynorphin A (DynA), endomorphin 1 (End1), and methionine‐enkephaline (Met). A microcartridge length of 4 mm was selected, sample was loaded for 10 min at 930 mbar and the retained peptides were eluted with 67 nL of an acidic hydro‐organic solution. Using SPE‐CE‐MS, peak area and migration time repeatabilities for the three opioid peptides were 12–27% and 4–5%, respectively. SPE recovery was lower for the less hydrophobic DynA (22%) than for End1 (66%) and Met (78%) and linearity was satisfactory in all cases between 5 and 60 ng/mL. The LODs varied between 0.5 and 1.0 ng/mL which represent an enhancement of two orders of magnitude when compared with CE‐MS. Cerebrospinal fluid (CSF) samples spiked with the opioid peptides were analyzed to demonstrate the applicability to biological samples. Peak area and migration time repeatabilities were similar to the standard solutions and the opioid peptides could be detected down to 1.0 ng/mL.     

Nickel/Copper Bilayer‐modified Screen Printed Electrode for Glucose Determination in Flow Injection Analysis

This work reports about the performance of a Ni/Cu‐modified screen printed electrodes (SPE/Ni/Cu), prepared by physical vapor deposition (PVD) in an oblique angle configuration (OAD), for non‐enzymatic glucose sensing applications. SPE/Ni/Cu electrodes showed an excellent reversibility and a catalytic behavior for detection of glucose that were controlled by the diffusion of reactants up to the active sites at the electrode surface. The study with a flow injection analysis (FIA) setup of the main experimental variables affecting the detection process has shown that the developed electrode system had an excellent glucose sensitivity of 1.04 A M⁻¹cm⁻² (R²:0.999), a linear response up to 1 mM, a limit of detection of 0.33 μM and a time of analysis of ca. 30 s per sample. The selectivity of the sensor was checked against various interferences, including ascorbic acid, uric acid, acetaminophen and other sugars, in all cases with excellent results. The feasibility of using this sensor for practical applications was successfully confirmed by determining the glucose concentration in different commercial beverages.     

Study of immobilized metal affinity chromatography sorbents for the analysis of peptides by on‐line solid‐phase extraction capillary electrophoresis‐mass spectrometry

Several commercial immobilized metal affinity chromatography sorbents were evaluated in this study for the analysis of two small peptide fragments of the amyloid β‐protein (Aβ) (Aβ(1–15) and Aβ(10–20) peptides) by on‐line immobilized metal affinity SPE‐CE (IMA‐SPE‐CE). The performance of a nickel metal ion (Ni(II)) sorbent based on nitrilotriacetic acid as a chelating agent was significantly better than two copper metal ion (Cu(II)) sorbents based on iminodiacetic acid. A BGE of 25 mM phosphate (pH 7.4) and an eluent of 50 mM imidazole (in BGE) yielded a 25‐fold and 5‐fold decrease in the LODs by IMA‐SPE‐CE‐UV for Aβ(1–15) and Aβ(10–20) peptides (0.1 and 0.5 μg/mL, respectively) with regard to CE‐UV (2.5 μg/mL for both peptides). The phosphate BGE was also used in IMA‐SPE‐CE‐MS, but the eluent needed to be substituted by a 0.5% HAc v/v solution. Under optimum preconcentration and detection conditions, reproducibility of peak areas and migration times was acceptable (23.2 and 12.0%RSD, respectively). The method was more sensitive for Aβ(10–20) peptide, which could be detected until 0.25 μg/mL. Linearity for Aβ(10–20) peptide was good in a narrow concentration range (0.25–2.5 μg/mL, R² = 0.93). Lastly, the potential of the optimized Ni(II)‐IMA‐SPE‐CE‐MS method for the analysis of amyloid peptides in biological fluids was evaluated by analyzing spiked plasma and serum samples.     

Incorporation of Disposable Screen‐Printed Electrodes for Use in Capillary Electrophoresis End‐Column Amperometric Detection System

The development and performance of an end‐column amperometric detection system integrated with disposable screen‐printed electrodes for capillary electrophoresis is presented. In this system, the electrode and capillary can be easily replaced and the capillary/electrode alignment procedure is straightforward. The use of easily replaceable screen‐printed electrodes offers a tremendous benefit for capillary electrophoresis applications requiring frequent replacement of the working electrode due to fouling. This simple and convenient system is very attractive for routine analyses by capillary electrophoresis with electrochemical detection. The separation and determination of uric acid in human urine is presented.     

Development of a sheathless CE‐ESI‐MS interface

A sheath‐flow interface is the most common ionization technique in CE‐ESI‐MS. However, this interface dilutes the analytes with the sheath liquid and decreases the sensitivity. In this study, we developed a sheathless CE‐MS interface to improve sensitivity. The interface was fabricated by making a small crack approximately 2 cm from the end of a capillary column fixed on a plastic plate, and then covering the crack with a dialysis membrane to prevent metabolite loss during separation. A voltage for CE separation was applied between the capillary inlet and the buffer reservoir. Under optimum conditions, 52 cationic metabolite standards were separated and selectively detected using MS. With a pressure injection of 5 kPa for 15 s (ca. 1.4 nL), the detection limits for the tested compounds were between 0.06 and 1.7 μmol/L (S/N = 3). The method was applied to analysis of cationic metabolites extracted from a small number (12 000) of cancer cells, and the number of peaks detected was about 2.5 times higher than when using conventional sheath‐flow CE‐MS. Because the interface is easy to construct, it is cost‐effective and can be adapted to any commercially available capillaries. This method is a powerful new tool for highly sensitive CE‐MS‐based metabolomic analysis.     

The in‐capillary DPPH‐capillary electrophoresis‐the diode array detector combined with reversed‐electrode polarity stacking mode for screening and quantifying major antioxidants in Cuscuta chinensis Lam

An in‐capillary 2, 2‐diphenyl‐1‐picrylhydrazyl (DPPH)‐CE‐the DAD (in‐capillary DPPH‐CE‐DAD) combined with reversed‐electrode polarity stacking mode has been developed to screen and quantify the active antioxidant components of Cuscuta chinensis Lam. The operation parameters were optimized with regard to the pH and concentration of buffer solution, SDS, β‐CDs, organic modifier, as well as separation voltage and temperature. Six antioxidants including chlorogenic acid, p‐coumaric acid, rutin, hyperin, isoquercitrin, and astragalin were screened and the total antioxidant activity of the complex matrix was successfully evaluated based on the decreased peak area of DPPH by the established DPPH‐CE‐DAD method. Sensitivity was enhanced under reversed‐electrode polarity stacking mode and 10‐ to 31‐fold of magnitude improvement in detection sensitivity for each analyte was attained. The results demonstrated that the newly established in‐capillary DPPH‐CE‐DAD method combined with reversed‐electrode polarity stacking mode could integrate sample concentration, the oxidizing reaction, separation, and detection into one capillary to fully automate the system. It was considered a suitable technique for the separation, screening, and determination of trace antioxidants in natural products.     

Investigation of commercial sorbents for the analysis of opioid peptides in human plasma by on‐line SPE‐CE

In this study, we investigated the performance of several commercial sorbents (Sep‐pack^® C18, ^tC18, C8 and ^tC2, Oasis^® HLB, Isolute^® ENV+, Strata^?‐X and Oasis^® MCX) for the determination of opioid peptides by solid‐phase extraction coupled on‐line to capillary electrophoresis (SPE‐CE). First, standard solutions were analyzed in order to achieve the lowest LOD and the best electrophoretic separations using UV detection. The best results were obtained using C18, C8 and ^tC2 sorbents, which were examined for the analysis of spiked human plasma samples. A double‐step sample clean‐up pretreatment, which consisted of precipitation with acetonitrile and filtration, was needed to prevent saturation of the on‐line SPE microcartridge. The filtration step was critical to obtain optimum analyte recovery and to clean up the sample matrix. A range of centrifugal filters and filtration conditions were tested and the recoveries of the sample pretreatment were evaluated by CE‐ESI‐MS. The LODs attained through SPE‐CE‐UV were approximately ten‐fold better with C18 than with C8 and ^tC2. The 0.1 μg/mL LODs achieved by C18‐SPE‐CE‐UV were further improved until we could detect 1 ng/mL concentrations of opioid peptides in plasma samples by C18‐SPE‐CE‐ESI‐MS, due to the outstanding selectivity of the MS detection.     

Capillary electrophoresis coupled with in‐column fiber‐optic laser‐induced fluorescence detection for the rapid separation of neodymium

In this study, in‐column fiber‐optic (ICFO) laser‐induced fluorescence (LIF) detection technique is coupled with capillary electrophoresis (CE) for the rapid separation of neodymium for the first time. The effects of buffer concentration, buffer pH, and separation voltage on the CE behaviors, including electrophoretic efficiency and detection sensitivity, are investigated in detail. Under the optimal condition determined in this study (15 mM borate buffer, pH 10.50, separation voltage 24 kV), neodymium could be separated effectively from the neighboring lanthanides (praseodymium and samarium) within several minutes, and the limit of detection for neodymium is estimated to be at the ppt level. The ICFO‐LIF‐CE system assembled in this study exhibits unique performance characteristics such as low cost and flexibility. Meanwhile, the separation efficiency and detection sensitivity of the assembled CE system are comparable to or somewhat better than those obtained in the previous traditional CE systems, indicating the potential of the assembled CE system for practical applications in the fields of spent nuclear fuel analysis, nuclear waste disposal/treatment, and nuclear forensics.     

On-column polymer-imbedded graphite inlet electrode for capillary electrophoresis coupled on-line with flow injection analysis in a poly(dimethylsiloxane) interface

A method for coupling an electrophoretic driven separation to a liquid flow, using conventional fused-silica capillaries and a soft polymeric interface is presented. A novel design of the electrode providing high voltage to the electrophoretic separation was also developed. The electrode consisted of a conductive polyimide/graphite imbedded coating immobilized onto the capillary electrophoresis (CE) column inlet. This integrated electrode gave the same separation performance as a commonly used platinum electrode. The on-column electrode also showed good electrochemical stability in chronoamperometric experiments. In addition, with this electrode design, the electrode position relative to the inlet end of the CE column will always be constant and well defined. The on-line flow injection analysis (FIA)-CE system was used with electrospray ionization (ESI)-time of flight (TOF)-mass spectrometry detection. The preparation of the PDMS (poly(dimethylsiloxane)) interface for FIA-CE is described in detail and used for initial tests of the on-column polymer-imbedded graphite inlet electrode. In this interface, a pressure-driven liquid flow, a make up CE electrolyte and a CE column inlet meet in a two-level cross (95 microm ID) in the PDMS structure, enabling independent flow characterization.     

Lamp‐based wavelength‐resolved fluorescence detection for protein capillary electrophoresis: Setup and detector performance

A lamp‐based fluorescence detection (Flu) system for CE was extended with a wavelength‐resolved (WR) detector to allow recording of full protein emission spectra. WRFlu was achieved using a fluorescence cell that employs optical fibres to lead excitation light from a Xe‐Hg lamp to the capillary window and protein fluorescence emission to a spectrograph equipped with a CCD. A 280 nm band pass filter etc. together with a 300 nm short pass cut‐off filter was used for excitation. A capillary cartridge was modified to hold the detection cell in a commercial CE instrument enabling WRFlu in routine CE. The performance of the WRFlu detection was evaluated and optimised using lysozyme as model protein. Based on reference spectral data, a signal‐intensity adjustment was introduced to correct for transmission losses in the detector optics that occurred for lower protein emission wavelengths. CE‐WRFlu of lysozyme was performed using BGEs of 50 mM sodium phosphate (pH 6.5 or 3.0) and a charged‐polymer coated capillary. Using the 3‐D data set, signal averaging over time and emission‐wavelength intervals was carried out to improve the S/N of emission spectra and electropherograms. The detection limit for lysozyme was 21 nM, providing sufficient sensitivity to obtain spectral information on protein impurities.     

Application of a Square‐Wave Potential Program for Time‐Dependent Amperometric Detection in Capillary Electrophoresis

Use of a square‐wave potential program for time‐dependent amperometric detection of analyte zones in capillary electrophoresis (CE) is described. Electrochemical detection for CE requires that the separation field be isolated from that of the electrochemical detection. This is generally done by physically separating the CE separation field from that of the detection. By applying a time variant potential program to the detection electrode, the detector current has a time dependence that can be used to help isolate the electrochemical detection current from that of the separation. When using a 20 μm inner‐diameter capillary, we find that a square‐wave potential program decreases the RMS baseline current from 4.5×10^?10 A, found with a constant potential amperometric detection, to 1.1×10^?10 A when using a square‐wave potential program. With a 75 μm inner‐diameter capillary, the improvement is even more dramatic, from 2.3×10^?9 A with amperometric detection to 2.06×10^?10 A when using a 1 Hz square‐wave potential program. When not using the time‐dependent detection with the 75 μm capillary, the analyte zones were beneath the S/N for the system and not detected. With the square‐wave potential program and time‐dependent detection, however, the analyte zones for an electrokinetic injection of 200 μM solution of 2,3‐dihydroxybenzoic acid were observed with the 75 μm inner‐diameter capillary. The improvement in the ability to discriminate the analytical signal from the background found experimentally is consistent with modeling studies.     

Sensitive determination of sulfonamides in environmental water by capillary electrophoresis coupled with both silvering detection window and in‐capillary optical fiber light‐emitting diode‐induced fluorescence detector

A new detector, silvering detection window and in‐capillary optical fiber light‐emitting diode‐induced fluorescence detector (SDW‐ICOF‐LED‐IFD), is introduced for capillary electrophoresis (CE). The strategy of the work was that half surface of the detection window was coated with silver mirror, which could reflect the undetected fluorescence to the photomultiplier tube to be detected, consequently enhancing the detection sensitivity. Sulfonamides (SAs) are important antibiotics that achieved great applications in many fields. However, they pose a serious threat on the environment and human health when they enter into the environment. The SDW‐ICOF‐LED‐IFD‐CE system was used to determine fluorescein isothiocyanate (FITC)‐labeled sulfadoxine (SDM), sulfaguanidine (SGD) and sulfamonomethoxine sodium (SMM‐Na) in environmental water. The detection results obtained by the SDW‐ICOF‐LED‐IFD‐CE system were compared to those acquired by the CE with in‐capillary optical fiber light‐emitting diode‐induced fluorescence detection (ICOF‐LED‐IFD‐CE). The limits of detection (LODs) of SDW‐ICOF‐LED‐IFD‐CE and ICOF‐LED‐IFD‐CE were 1.0–2.0 nM and 2.5–7.7 nM (S/N = 3), respectively. The intraday (n = 6) and interday (n = 6) precision of migration time and corresponding peak area for both types of CE were all less than 0.86% and 3.68%, respectively. The accuracy of the proposed method was judged by employing standard addition method, and recoveries obtained were in the range of 92.5–102.9%. The results indicated that the sensitivity of the SDW‐ICOF‐LED‐IFD‐CE system was improved, and that its reproducibility and accuracy were satisfactory. It was successfully applied to analyze SAs in environmental water.     

Use of different buffers for detection and separation in determination of physio‐active components in oolong tea infusion by CZE with amperometric detection

With a view of simultaneous determination of physio‐active ingredients in oolong tea infusion: sugars, amino acids, epigallocatechin gallate and ascorbic acid, a novel CZE with amperometric detection method was studied. Operated in a wall‐jet configuration, 100 mmol/L NaOH was used in detecting cell to lead the electrocatalysis oxidation behaviors of the analytes on a 300 μm diameter copper‐disc electrode (working electrode), while in separating capillary, a mild alkaline running buffer consisting in a mixture of 30 mmol/L borate and 40 mmol/L phosphates charged and carried analytes to detecting end. The methodology research was performed for system stability and suitability. Under the optimal CE conditions, analytes could be separated within moderate time period. Good linearity between peak area and concentration existed over three orders of magnitude; lower RSD and LOD were achieved. The oolong tea infusion was assayed and result was satisfactory.     

Determination of UV filters in river water samples by in‐line SPE‐CE‐MS

The use of SPE coupled in‐line to CE using electrospray MS detection (in‐line SPE‐CE‐ESI‐MS) was investigated for the preconcentration and separation of four UV filters: benzophenone‐3, 2,2‐dihydroxy‐4‐methoxybenzophenone, 2,4‐dihydroxybenzophenone and 2‐phenylbenzimidazole‐5‐sulphonic acid. First, a CE‐ESI‐MS method was developed and validated using standard samples, obtaining LODs between 0.06 μg/mL and 0.40 μg/mL. For the in‐line SPE‐CE‐ESI‐MS method, three different sorbents were evaluated and compared: Oasis HLB, Oasis MCX, and Oasis MAX. For each sorbent, the main parameters affecting the preconcentration performance, such as sample pH, volume, and composition of the elution plug, and sample injection time were studied. The Oasis MCX sorbent showed the best performance and was used to validate the in‐line SPE‐CE‐ESI‐MS methodology. The LODs reached for standard samples were in the range between 0.01 and 0.05 ng/mL with good reproducibility and the developed strategy provided sensitivity enhancement factors between 3400‐fold and 34 000‐fold. The applicability of the developed methodology was demonstrated by the analysis of UV filters in river water samples.     

CE‐ECL detection of gatifloxacin in biological fluid after clean‐up using SPE

A simple, rapid and sensitive CE method has been proposed for the determination of gatifloxacin in biological fluid. This method is based on the ECL reaction of gatifloxacin and tris(2,2'‐bipyridyl)ruthenium(II) occurred in the end‐column detection cell. Under the optimal conditions, gatifloxacin can be assayed within 10 min over the concentration range of 5.0×10^?8?5.0×10^?6 g/mL with the theoretical plate numbers of 18 000. The intra‐day and inter‐day precision of the signal intensity and the migration time shows acceptable reproducibility for the analysis of gatifloxacin. The presented method has been successfully applied to determine the concentrations of gatifloxacin in urine and blood samples after clean‐up using C₁₈ SPE column.     

An in‐line SPE strategy to enhance sensitivity in CE for the determination of pharmaceutical compounds in river water samples

In this study, the suitability of solid‐phase extraction (SPE) coupled in‐line to CE with UV–Vis detection was evaluated for the preconcentration and separation of diluted solutions of five pharmaceuticals compounds: benzafibrate, piroxicam, diclofenac sodium, naproxen and clofibric acid. An SPE analyte concentrator containing Oasis^® HLB sorbent was constructed without frits and placed near the inlet end of the separation capillary. Different parameters such as sample pH, composition and volume of the elution plug and sample loading time were studied in order to obtain the maximum preconcentration factors. The LODs reached for standard samples were in the range 0.06–0.5 ng/mL with good reproducibility, and the developed strategy provides sensitivity enhancement factors around 14 000‐fold in peak area and 5900‐fold in peak height compared with the normal hydrodynamic injection. Finally, river water samples fortified with the pharmaceutical compounds were analyzed by the developed in‐line SPE‐CE‐UV method in order to show the potential of the methodology for the analysis of environmental aquatic samples. For these samples, high values of relative recoveries, between 73–107% and 79–103% for two concentration levels, 5 and 25 ng/mL, respectively, were obtained and LODs ranged between 0.19 and 1 ng/mL.     

Design and evaluation of capillary coupled with optical fiber light‐emitting diode induced fluorescence detection for capillary electrophoresis

A new detector, capillary coupled with optical fiber LED‐induced fluorescence detector (CCOF‐LED‐IFD, using CCOF for short), is introduced for CE. The strategy of the present work was that the optical fiber and separation capillary were, in the parallel direction, fastened in a fixation capillary with larger inner diameter. By employing larger inner diameter, the fixation capillary allowed the large diameter of the optical fiber to be inserted into it. By transmitting an enhanced excitation light through the optical fiber, the detection sensitivity was improved. The advantages of the CCOF‐CE system were validated by the detection of riboflavin, and the results were compared to those obtained by the in‐capillary common optical fiber LED‐induced fluorescence detector (IC‐COF‐LED‐IFD, using COF for short). The LODs of CCOF‐CE and COF‐CE were 0.29 nM and 11.0 nM (S/N = 3), respectively. The intraday (n = 6) repeatability and interday (n = 6) reproducibility of migration time and corresponding peak area for both types of CE were all less than 1.10 and 3.30%, respectively. The accuracy of the proposed method was judged by employing standard addition method, and recoveries obtained were in the range of 98.0–102.4%. The results indicated that the sensitivity of the proposed system was largely improved, and that its reproducibility and accuracy were satisfactory. The proposed system was successfully applied to separate and determine riboflavin in real sample.     

Laser‐Induced Fluorometry for Capillary Electrophoresis

Laser‐induced fluorometry (LIF) has achieved the detection of single molecules, which ranks it among the most sensitive of detection techniques, whereas capillary electrophoresis (CE) is known as a powerful separation method with resolution that is beyond the reach of many other types of chromatography. Therefore, a coupling of LIF with CE has established an unrivaled analytical technique in terms of sensitivity and resolution. CE‐LIF has demonstrated excellent performance in bioanalytical chemistry for the high‐resolution separation and highly sensitive detection of DNAs, proteins, and small bioactive molecules. This review describes the CE‐LIF methods developed by the author's group that include indirect and direct detection using diode lasers, post‐column derivatization, and Hadamard transformation, as well as applications to the binding assays of specific DNA immunoassays of proteins and to the determination of anticancer drugs.     

Trace Determination of Benzalkonium Chlorides in River and Wastewater by Capillary Electrophoresis following Solid‐Phase Extraction Coupled with Salting‐Out Extraction

Trace levels analysisbenzalkonium chlorides (BAKs) in river water and wastewater treatment plants (WWTP) effluents were determined by capillary electrophoresis (CE) following solid‐phase extraction (SPE) and salting‐out extraction. Salting‐out extraction using an appropriate ratio of sodium chloride (NaCl) and acetonitrile (ACN) mixed with concentrated SPE elutant was capable of providing more than 500‐fold enhancement in detection sensitivity. The ratios of ACN and NaCl for salting‐out extraction were investigated and optimized. Matrix interference was eliminated by salting‐out extraction. Limits of quantitation of BAK homologues were achieved at 0.1 μg/L in 250 mL water samples. Recoveries of BAKs in various spiked water samples ranged from 70% to 84% with relative standard deviation (RSD) less than 9%. Trace amounts of total BAKs were detected in river water and WWTP effluent samples ranging from 27 to 145 μg/L at the first time by CE.     

Microchip Capillary Electrophoresis‐Electrochemistry with Rigid Graphite‐Epoxy Composite Detector

A new rigid graphite‐epoxy composite electrode for electrochemical detection in microchip electrophoresis is described. The end‐column wall‐jet detection design relying on tubular rigid composite working electrode shows favorably low noise level and high signal‐to‐noise ratio when compared to glassy carbon detector. The performance of rigid graphite‐epoxy composite detector was compared to glassy carbon detector using dopamine and catechol as model analytes. The various parameters of the microchip electrophoresis‐rigid graphite‐epoxy composite detector were optimized.