负载Co介孔分子筛催化热解乙醇制备纳米碳管

以硅酸钠为原料,CTAB为模板剂,水热法合成MCM-41介孔分子筛,采用浸渍法制备负载钴的介孔分子筛(Co/MCM-41),并将其作为催化剂,CVD法热解无水乙醇制备CNTs.利用XRD、TEM、比表面积和孔径分布测定和Raman光谱等方法对所合成的介孔分子筛和纳米碳管进行了表征.结果表明:所制备的Co/MCM-41样品具有典型的MCM-41的介孔结构;当热解反应温度为750℃下所制备出的纳米碳管的品质最好.     

具有强酸位的六方和立方介孔硅铝分子筛合成及催化活性比较

六方 MCM- 41和立方 MCM- 48介孔分子筛是长程有序的介孔材料 ,由于其孔壁是无定形结构 ,具有较弱的酸性 ,限制了其应用范围 .若能提高它们的酸强度则可提高其在石油炼制和精细化工中的应用价值 .现已采用多种改进方法来提高其酸强度 [1～ 6 ] ,但所合成的介孔材料均为六方结构 ,而具有立方结构的材料未见文献报道 .本文采用两步晶化合成法 ,用低浓度的表面活性剂合成出具有强酸位的立方介孔分子筛 ( MB48) ,还通过调节溶液的酸碱性合成出六方介孔分子筛 ( MB41 ) ,对样品的结构、酸性和催化性能进行了表征和比较 .1　实验部分1 .1　 β…     

纳米介孔分子筛MCM-41的微波辐射合成法

报导了纳米介孔分子筛MCM-41的微波辐射合成法,运用XRD、HRTEM、IR、TG、荧光光谱和低温N2吸附等技术对其进行了表征.研究结果表明,利用微波技术合成MCM-41,操作便利,节能省时.所得产物具有六方介孔排列结构,孔径约2.5 nm;颗粒大小分布均匀,平均粒径约40 nm;比表面积和孔隙率高,吸附量大,热稳定性好;在近紫外光激发下,显示出纳米粒子的量子发光效应.     

模板剂对全硅MCM-41介孔分子筛结构的影响

分别采用十六烷基三甲基溴化铵和十六烷基三乙基溴化铵作为模板剂,硅溶胶为硅源,用水热晶化法在碱性（NaOH）介质中合成了MCM-41介孔分子筛样品.通过XRD、N2吸附-脱附、TG-DTA、IR等测试手段对这两种样品进行了对比表征分析.考察了两种不同模板剂对其晶体结构、比表面及孔径大小的影响.实验结果表明,相对于十六烷基三甲基溴化铵做模板剂,采用大头基的十六烷基三乙基溴化铵可以合成较大孔径和孔容（分别为4.72 nm和1.14 cm3•g-1）的MCM-41介孔分子筛,而且具有较窄的孔径分布,因此对于合成大孔径的介孔分子筛MCM-41,十六烷基三乙基溴化铵是一种很好的模板剂.     

介孔分子筛COAPSO的合成、表征及其环己烷氧化催化性能

采用一步晶化法合成了具有McM-41介孔分子筛结构的CoAPSO分子筛.用X射线粉末衍射(XRD)、元素分析(ICP)、氮气吸附、透射电镜(TEM)、紫外可见漫反射光谱(UV-Vis)和热重分析(TG)等对样品进行了表征.合成的样品热稳定性高,孔径大约在2.5 nm左右.钴原子以四配位形式进入介孔孔壁中;随着钴含量增加,样品的孔径减小,孔壁增厚.在环己烷氧化反应中,所合成的CoAPSO分子筛显示出较高的催化活性和环己酮选择性;当钴含量为0.34%时,单位钴原子上环己烷的转化数达到420.5.     

含钴介孔分子筛催化热解乙醇制备纳米碳管

以CTAB为模板剂,硅酸钠、氯化钴为原料,通过水热法合成含钴介孔分子筛(Co-MCM-41)。以所合成的Co-MCM-41做催化剂,采用化学气相沉积(CVD)法催化热解乙醇制备纳米碳管。通过XRD、FT-IR、TEM、N2吸附-脱附和Raman光谱等分析手段对所合成的介孔分子筛和纳米碳管进行了表征。结果表明:合成的Co-MCM-41样品具有MCM-41的介孔结构,比表面积较大且介孔有序性较好。以所合成的含钴介孔分子筛催化热解乙醇制备出管径均匀、管壁较厚、顶端开口的多壁纳米碳管。     

介孔材料MCM-41的合成与性能表征

在水热条件下用新的合成控制手段得到孔壁较厚的MCM-41介孔分子筛材料,并采用XRD、N2吸附、TG-DTA、SEM和吡啶程序升温脱附等测试手段对合成的MCM-41样品进行表征,结果表明合成的介孔材料结晶度比较高,具有六方排列的孔道结构,孔径分布较窄,BET表面积较大,样品热稳定性高,吡啶-TPD谱图表明样品具有弱的或中等强度的酸性.用MCM-41作为活性组分制备成催化剂,进行微反活性实验,表明其裂化活性较低,但对柴油有较高的选择性.     

铈掺杂的介孔分子筛的水热合成与结构性能

以硅酸钠、硝酸铈铵为原料,十六烷基三甲基溴化铵为模板剂,通过水热法合成铈掺杂的介孔分子筛CeMCM-41.分别采用X射线粉末衍射(XRD)、透射电子显微镜(TEM)、红外光谱(FT-IR)、紫外-可见分光光度计(UV-Vis)和N2吸附-脱附等技术对产物的晶相、结构、形貌、比表面积和孔径进行表征.同时研究硅铈物质的量比对合成材料结构性能的影响.实验结果表明:水热条件下成功合成出铈掺杂的MCM-41介孔分子筛,其比表面积为480.5～1 295.2m2/g,平均孔径在2.70～6.29 nm之间.随着稀土元素铈的掺杂量的增加,CeMCM-41介孔分子筛的比表面积和孔体积变小,介孔有序性变差.     

氨水介质中含Ti的MCM-41介孔分子筛的合成

 在氨水介质中采用TiCl3和正硅酸乙酯合成了含Ti量不同的MCM-41介孔分子筛. 该方法可避免使用昂贵的辅助模板剂,也不需要加入醇来调节水解速度,因而合成过程相对简单、易于控制. 采用XRD和N2吸附-脱附等技术对介孔分子筛的结构进行了表征. 结果表明,合成的MCM-41介孔分子筛的六方介孔有序性好,结晶度高. UV-Vis光谱表明,Ti-MCM-41在200～300 nm间出现了四个清晰可辨的吸收峰,说明Ti原子以多种状态存在于介孔分子筛骨架中.     

介孔分子筛的制备与苯加氢反应的催化性能

1992年美国Mobil公司的研究人员首次报道合成出具有规则孔结构的M41S系列介孔分子筛材料.由于介孔材料独特的性质,引起了人们极大的兴趣,在其合成与性能等方面进行了大量的研究,合成出了多种系列不同性能的介孔分子筛,并研究了介孔分子筛作为催化剂或催化剂载体在各类催化反应中的催化性能.     

Characterization of CoMCM-41 mesoporous molecular sieves obtained by the microwave irradiation method

CoMCM-41 mesoporous molecular sieves with different amounts of cobalt were synthesized via the microwave irradiation method. The samples were characterized by X-ray diffraction (XRD), Fourier transform infrared (FT-IR), temperature programmed reduction (TPR), transmission electron microscopy (TEM) and N₂ adsorption-desorption technique, and thermal and hydrothermal stabilities of synthesized CoMCM-41 samples were also investigated. Results show that these synthesized materials have typical mesoporous structure of MCM-41. Also, specific surface area and pore volume of synthesized CoMCM-41 decrease with increasing amount of cobalt added, and mesoporous ordering also decreases. When the molar ratio of SiO₂:CoO in the starting material is 1.0:0.05, mesoporous ordering of synthesized CoMCM-41 is the best among the four doping contents. On the other hand, results of thermal and hydrothermal tests show that CoMCM-41 after calcination at 750 °C for 3 h or hydrothermal treatment at 100 °C for 5 days still retains mesostructure. However, mesoporous framework is entirely damaged after calcination at 850 °C for 3 h.     

中孔硅酸盐材料MCM-41的合成与表征研究(英文)

以十六烷基三甲基溴化铵为模板剂,硅酸钠为硅源,铝酸钠为铝源,在水热条件下成功地合成出了ＭＣＭ－４１中孔硅酸盐材料。采用ＸＲＤ、低温Ｎ２吸附脱附等测试手段对合成的ＭＣＭ－４１样品进行了表征。通过优化合成条件,合成出孔径３.２ ｎｍ、比表面９０４ｍ２／ｇ和孔壁厚约１.４６ ｎｍ的ＭＣＭ－４１分子筛。催化活性测定采用微反应活性实验来评价其活性和选择性。     

Synthesis of Highly ordered Large Size Mesoporous Silica and Effect of Stabilization as Enzyme Supports in Organic Solvent

ＩｎｔｒｏｄｕｃｔｉｏｎＴｈｅｔｅｃｈｎｉｑｕｅｆｏｒｅｎｖｉｒｏｎｍｅｎｔｐｒｏｔｅｃｔｉｏｎｈａｓｂｅ ｃｏｍｅｉｎｃｒｅａｓｉｎｇｌｙｉｍｐｏｒｔａｎｔ .Ｔｈｅｃｌｅａｒｂｉｏｄｅｃｏｍｐｏｓｉ ｔｉｖｅｍｅｔｈｏｄｓｈａｖｅｂｅｅｎｎｏｔｅｄｉｎｒｅｃｅｎｔｙｅａｒｓ ,ａｎｄｐｅｒｏｘｉｄａｓｅｓ(ｈｅｍｅｅｎｚｙｍｅ)ｈａｖｅｂｅｅｎｗｉｄｅｌｙｕｔｉｌｉｚｅｄｉｎｓｏｍｅａｐｐｌｉｃａｔｉｏｎｓｓｕｃｈａｓｄｅｐｏｌｙｍｅｒｉｚａｔｉｏｎｏｆｌｉｇｎｉｎｏｒｃｏａｌ[1,2 ] ,ａｎｄｔｈｅｎ…     

Large Pore Mesoporous MCM-41 Templated from Cetyltriethylammonium Bromide

Following hydrothermal synthesis process, MCM-41 was synthesized by using cetyltfiethylammonium bromide as templating agent. The experimental results showed that MCM-41 with pore diameter in the range of 4-7 nm can be obtained by adjusting nSurf./nSi. It was proved that cetyltriethylammonium bromide is an effective templating agent for increasing pore diameter of molecular sieve MCM-41.     

MCM-41分子筛的合成及129Xe核磁共振的研究

ＭＣＭ４１中孔分子筛是１９９２年由Ｍｏｂｉｌ公司的科学家Ｋｒｅｓｇｅ［１］等人首次合成的,并在《自然》杂志发表。这种中孔分子筛具有六角形孔径,孔径２ｎｍ～１０ｎｍ,这种分子筛的孔径可以通过水晶模板来控制［２］。已报道的合成ＭＣＭ４１,孔径一般在２．０ｎｍ～３．５ｎｍ,使用的水晶模板一般是单一或两种阳离子季铵盐表面活性剂［３,４］。本论文通过引入第二种扩孔模板,与阳离子季铵盐协同作用,合成了孔径５．２ｎｍ（ＢＥＴ法测）的ＭＣＭ４１。通过氮气的吸脱附,测定了分子筛的比表面和孔径等性质。Ｊ．Ｆｒａｉｓｓａｒｄ…     

New Routes to the Synthesis of Mesoporous Materials and Their Properties

The factors that influence the hydrothermal synthesis of MCM-41 were investigated, and it was found that compared with those from high H₂O/SiO₂ systems(designated MCM-41-A), the products from low H₂O/SiO₂ systems(designated MCM-41-B) exhibited a less-defined X-ray powder diffraction (XRD) pattern with a broader main reflection peak at a lower 2θ diffraction angle. MCM-41-B possesses a smaller surface area but a larger pore size than MCM-41-A. New routes including direct thermal treatment, room-temperature crystallization and microwave heating were developed for the formation of MCM-41, and the properties of the products prepared from these new routes were compared with those of the MCM-41 hydrothermally synthesized. The pore sizes of MCM-41 materials are uniformly distributed with an effective pore diameter that falls into the range of 2-4 nm, where as the products from wet-gel thermal treatment possess two kinds of mesopores:the well-defined smaller pores distributed at 3 nm and the larger one within 8-20 nm. The MAS NMR spectroscopy revealed that after calcination to remove the organic template in Al-containing MCM-41, a small part of the tetrahedrally-coordinated framework aluminum atoms became octahedrally-coordinated and a considerable amount of Si-OH species were generated.     

Investigation of the physicochemical aspects from natural kaolin to Al-MCM-41 mesoporous materials

Aluminum-containing hexagonally ordered mesoporous silica Al-MCM-41 was synthesized by hydrothermal treatment of leached products produced by pre-grinding and subsequent acid leaching of natural kaolin, without addition of silica or aluminum regents. The resulting Al-MCM-41 had a high surface area of 1041 m(2)/g, a pore volume of 0.97 mL/g, and an average pore diameter of 3.7 nm with narrow pore size distribution centered at 2.7 nm. During the synthesis process of Al-MCM-41 from natural kaolin, the evolutions of chemical environments for Si and Al atoms should be emphasized. Wide angle X-ray diffraction (WAXRD), high-resolution transmission electron micrographs (HRTEMs), solid-state magic-angle-spinning nuclear magnetic resonance (MAS NMR), Fourier transform infrared spectroscopy (FT-IR) were used to trace the variations of chemical structures. Pretreatment of grinding and subsequent acid leaching acted as an important role in the whole synthesis process. NMR spectroscopy showed that Q(3) structure (Si(SiO)(3)(OH)), condensed Q(4) framework structure (Si(SiO)(4)), also the octahedral and tetrahedral Al existed in the leached sample and Al-MCM-41, with higher chemical contents of Q(4) structure and the octahedral Al in final product Al-MCM-41 than those in the leached sample. A possible mechanism for the formation of Al-MCM-41 from natural kaolin was suggested.     

MCM-41分子筛的合成及129Xe核磁共振的研究

Purely siliceous MCM-41 with a narrow pore-size distribution, different pore size, high surface area was synthesized . As prepared, calcined and catalytically tested MCM-41 materials have been comprehensively characterized by N₂ adsorption/desorption at 77K and ¹²⁹Xe NMR. By adding mesitylene during the synthesis, the pore size of MCM-41 was enlarged to 5.2nm. The chemical shift in ¹²⁹Xe NMR spectroscopy of adsorbed xenon indicates that the MCM-41 is one dimensional pore channels .