Tuning the mechanical properties and degradation properties of polydioxanone isothermal annealing

Polydioxanone (PPDO) is synthesized by ring-opening polymerization of p-dioxanone, using stannous octoate as the catalyst. The polarized optical micrograph (POM) shows thes pherulite growth rate of PPDO decreases with an increase in the isothermal crystallization temperature. PPDO is compression-molded into bars, and PPDO bars are subjected to isothermal annealing at a range of temperatures (Ta = 50, 60, 70, 80, 90, and 100 °C), and correspond to three different annealing times (ta = 1h, 2h, 3h). The effect on PPDO is investigated by using differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), X-ray diffraction (XRD), and scanning electron microscopy (SEM). With an increase in Ta and ta, the grain size and the degree of crystallinity also increase. Meanwhile, the tensile strength is significantly improved. The PPDO bars (90 °C, 2 h) reach the maximum crystallinity (57.21%) and the maximum tensile strength (41.1 MPa). Interestingly, the heat treatment process does not result in serious thermal degradation. It is observed that the hydrolytic degradation of the annealed PPDO is delayed to some extent. Thus, annealed PPDO might have potential applications, particularly in the fields of orthopedic fixation and tissue engineering.     

Preparation and mechanical properties of thermal energy storage microcapsules

A series of heat energy storage microcapsules was prepared using melamine-formaldehyde resin as the shell material and the mechanical properties of the shell were investigated. A phase change material whose melting point was 24 °C was used as core and the quantity of heat involved in phase transition was 225.5 J/g. Average diameter of the microcapsules varied from 5 to 10 μm, and the globular surface was smooth and compact. The mechanical properties of the shell were evaluated by observing the surface morphological structure change after application of pressure by means of scanning electron microscopy. When the mass ratio of the core and shell material is 3:1, a yield point of about 1.1×10⁵ Pa was found and when the compression was increased beyond this point the microcapsules showed plastic behavior. This has been attributed to the cross-link density and to the high degree of reaction of the shell material. Different yield points subsequently reflected differences in the mechanical behavior. It was also found that the mechanical intensity of double-shell microcapsules was better than that of single shelled ones.     

Assembly and mechanical properties of phosphorus dendrimer/polyelectrolyte multilayer microcapsules

We report the preparation, characterization, and mechanical properties of polyelectrolyte/phosphorus dendrimer multilayer microcapsules. The shells of these microcapsules are composed either by alternating poly(styrenesulfonate) (PSS) and positively charged dendrimer G4(NH+Et2Cl-)96 or by alternating poly(allylamine hydrochloride) (PAH) and negatively charged dendrimer G4(CH-COO-Na+)96. The same multilayers were constructed on planar support to examine their layer-by-layer growth and to measure the multilayer thickness. Surface plasmon resonance spectroscopy (SPR) showed regular linear growth of the assembly upon each bilayer deposited. We probe the mechanical properties of these polyelectrolyte/dendrimer microcapsules by measuring force-deformation curves with the atomic force microscope (AFM). The experiment suggests that they are much softer than PSS/PAH microcapsules studied before. This softening is attributed to an enhanced permeability of the polyelectrolyte/dendrimer multilayer shells as compared with multilayers formed by linear polyelectrolytes. In contrast, Young's modulus of both dendrimer-based multilayers was found to be on the same order as that of PSS/PAH multilayers.     

Tuning the hydrophobic properties of silica particles by surface silanization using mixed self-assembled monolayers

Here we describe a novel method of preparing hydrophobic silica particles (100-150 nm; water contact angle of dropcasted film ranging from 60 degrees to 168 degrees) by surface functionalization using different alkyltrichlorosilanes. During their preparation, the molecular surface roughness is also concurrently engineered facilitating a change in both the surface chemical composition and the geometrical microstructure to generate hierarchical structures. The water contact angle has been measured on drop-cast film surface. The enhancement in the water contact angle on 3D (curved) SAMs in comparison to that on 2D (planar) surface is discussed using the Cassie-Baxter equation. These silica particles can be utilized for many potential applications including selective adsorbents and catalysts, chromatographic supports and separators in microfluidic devices.     

Designing a simple ratcheting system to sort microcapsules by mechanical properties

Using computational modeling, we analyze the fluid-driven motion of compliant particles over a rigid, saw-toothed surface. The particles are modeled as fluid-filled elastic shells and, thus, simulate ex vivo biological cells or polymeric microcapsules. Through the model, we demonstrate how the patterned surface and an oscillatory shear flow can be combined to produce a ratcheting motion, yielding a straightforward method for sorting these capsules by their relative stiffness. Since the approach exploits the capsule's inherent response to the substrate, it does not involve explicit measurement and assessment. Because the process utilizes an oscillatory shear, the sorting can be accomplished over a relatively short portion of the substrate. Due to these factors, this sorting mechanism can prove to be both efficient and relatively low-cost.     

The role of microstructure on the mechanical properties of polyurethane foams containing thermoregulating microcapsules

Rigid polyurethane foams with up to 50 wt% of microcapsules from LDPE-EVA containing Rubitherm^®RT27 were synthesized. The influence of microcapsules on the foams density, microstructure and mechanical resistance was studied. Cell size and strut and wall thicknesses were analyzed by SEM. The relationships between densities and foam microstructures with their Young's moduli and collapse stress were found by the Gibson and Ashby formulations and the Kerner equation for mechanical properties of composites. It was found a cell structure change from polyhedral closed-cells to spherical or amorphous open-cells. A good agreement between the experimental and theoretical data was observed but requiring a cell form factor. Thus, Fitting parameters confirmed the high trend of these microcapsules to be incorporated into the foam cell walls and the form factors depicted the abrupt change of cell morphology. Thus, these equations are suitable for predicting the mechanical properties of foams containing fillers of low mechanical resistance.     

The effect of mechanical activation on the hydration properties of nanodispersed silica

The hydration of highly dispersed nanosize silica was studied by low-temperature ¹H NMR spectroscopy before and after the mechanical activation in a ball mill.     

Nanostructure and mechanical properties of polybutylacrylate filled with grafted silica particles

We investigate the nanostructure and the linear rheological properties of polybutylacrylate (PBA) filled with St?ber silica particles grafted with PBA chains. The silica volume fractions range from 1.8 to 4.7%. The nanostructure of these suspensions is investigated by small-angle neutron scattering (SANS), and we determine their spectromechanical behavior in the linear region. SANS measurements performed on low volume fraction composites show that the grafted silica particles are spherical, slightly polydisperse, and do not form aggregates during the synthesis process. These composites thus constitute model filled polymers. The rheological results show that introducing grafted silica particles in a polymer matrix results in the appearance of a secondary process at low frequency: for the lowest volume fractions, we observe a secondary relaxation that we attribute to the diffusion of the particles in the polymeric matrix. By increasing the silica volume fraction up to a critical value, we obtain gellike behavior at low frequency as well as the appearance of a structure factor on the scattering intensity curves obtained by SANS. Further increasing the silica particle concentration leads to composites exhibiting solidlike low-frequency behavior and to an enhanced structure peak on the SANS diagrams. This quantitative correlation between the progressive appearance of a solidlike rheological behavior, on one hand, and a structure factor, on the other hand, supports the idea that the viscoelastic behavior of filled polymers is governed by the spatial organization of the fillers in the matrix.     

Characterization of the mechanical properties of cross-linked serum albumin microcapsules: effect of size and protein concentration

A microfluidic technique is used to characterize the mechanical behavior of capsules that are produced in a two-step process: first, an emulsification step to form droplets, followed by a cross-linking step to encapsulate the droplets within a thin membrane composed of cross-linked proteins. The objective is to study the influence of the capsule size and protein concentration on the membrane mechanical properties. The microcapsules are fabricated by cross-linking of human serum albumin (HSA) with concentrations from 15 to 35 % (w/v). A wide range of capsule radii (～40–450 μm) is obtained by varying the stirring speed in the emulsification step. For each stirring speed, a low threshold value in protein concentration is found, below which no coherent capsules could be produced. The smaller the stirring speed, the lower the concentration can be. Increasing the concentration from the threshold value and considering capsules of a given size, we show that the surface shear modulus of the membrane increases with the concentration following a sigmoidal curve. The increase in mechanical resistance reveals a higher degree of cross-linking in the membrane. Varying the stirring speed, we find that the surface shear modulus strongly increases with the capsule radius: its increase is two orders of magnitude larger than the increase in size for the capsules under consideration. It demonstrates that the cross-linking reaction is a function of the emulsion size distribution and that capsules produced in batch through emulsification processes inherently have a distribution in mechanical resistance.     

Tuning the mesostructures of vinyl silica by adjusting the micellar curvature

In our previous study (Wang, Y. Q.; Yang, C.-M.; Zibrowius, B.; Spliethoff, B.; Lindén, M.; Schüth, F. Chem. Mater. 2003, 15, 5029), mesoporous vinyl-functionalized silica (vinyl silica) with hexagonal P6mm and cubic Ia3d structures has been synthesized at different loadings of vinyl groups and at different concentrations of sodium chloride when triblock copolymer P123 was used as a template. Our further investigations presented in this article reveal that at a loading of 10% vinyl groups, well-ordered cubic Ia3d structure was obtained at a low concentration of Na2SO4 (0.5 M) and the hexagonal structure was produced at 1.0 M NaCl. When NaNO3 was used as the inorganic salt, the hexagonal structure was still maintained even at a salt concentration of 2.0 M. The result is in accordance with the Hofmeister series order (salting-out effect): SO4(2-) > Cl- > NO3(-). The lowering of the acidity also induced the formation of the cubic Ia3d structure. At 20% loading, hexagonal structure can be obtained by adding the more hydrophilic Pluronic F127 (EO106PO70EO106) to the acidic solutions of P123, but the hexagonal structure cannot be produced with pure P123 under the synthesis conditions investigated. All of these results can be rationalized through hydrophilic-hydrophobic balance and the change in micellar curvature. Furthermore, 10% mercaptopropyl-functionalized mesoporous silica with cubic Ia3d structure was designed and synthesized successfully with the assistance of an inorganic salt (NaCl) in an acidic solution of P123, which is the first example of mercaptopropyl-functionalized large-pore mesoporous silica with high loadings.     

Determination of mechanical properties of silica compounds using a curing kinetic model

Curing is the final step in rubber goods production and the mechanical properties of the vulcanized items, strongly depend on the processing conditions. The objective of this research is to predict the mechanical properties of SBR silica compound using kinetic data obtained from curemeter measurements. The model proposed is based on two curing parameters and on mechanical properties measured in the cured and uncured state. Results showed that the model is able to accurately predict the mechanical properties of the isothermal cured compound and therefore has potential application in the non-isothermal curing cycle optimization.     

Tuning the mechanical properties in model nanocomposites: Influence of the polymer‐filler interfacial interactions

This article presents a study of the polymer‐filler interfacial effects on filler dispersion and mechanical reinforcement in Polystyrene (PS)/silica nanocomposites by direct comparison of two model systems: ungrafted and PS‐grafted silica dispersed in PS matrix. The structure of nanoparticles has been investigated by combining small angle neutron scattering measurements and transmission electronic microscopic images. The mechanical properties were studied over a wide range of deformation by plate–plate rheology and uni‐axial stretching. At low silica volume fraction, the particles arrange, for both systems, in small finite size nonconnected aggregates and the materials exhibit a solid‐like behavior independent of the local polymer‐fillers interactions suggesting that reinforcement is dominated by additional long range effects. At high silica volume fraction, a continuous connected network is created leading to a fast increase of reinforcement whose amplitude is then directly dependent on the strength of the local particle–particle interactions and lower with grafting likely due to deformation of grafted polymer. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2011     

Preparation and mechanical properties of bacterial cellulose nanocomposites loaded with silica nanoparticles

Bacterial cellulose (BC), which is produced by Gluconacetobacter xylinus (Ga. xylinus) in culture, is made up of a three-dimensional network of ribbon-shaped bundles of cellulose microfibrils. In the current studies, we used two processes to prepare nanocomposites of BC filled with silica particles. In Process I, Ga. xylinus was incubated in medium containing silica sol Snowtex 0 (ST 0, pH 2–4) or Snowtex 20 (ST 20, pH 9.5–10.0). The elastic modulus at 20 °C was improved by keeping the amount of silica in the nanocomposites below 4% when ST 20 was used and below 8.7% when ST 0 was used. This process allowed incorporation of 50% silica in BC. Inclusion of higher amounts of silica reduced the modulus at 20 °C and the strength of the nanocomposites below that of BC. X-ray diffraction measurements revealed that the silica particles disturb the formation of ribbon-shaped fibrils and affect the preferential orientation of the ( ) plane. We also produced BC-silica nanocomposites by Process II, wherein the BC hydrogel was immersed in different concentrations of silica sols, allowing silica particles to diffuse into the BC hydrogel and lodge in the spaces between the ribbon-shaped fibrils. This method increased the modulus at 20°C and the strength compared to the BC matrix, but it was difficult to load the BC with more than 10% silica in this way.     

Effects of incorporation of modified silica nanoparticles on the mechanical and thermal properties of PMMA

Silica nanoparticles of various sizes have been incorporated by melt compounding in a poly(methyl methacrylate) (PMMA) matrix to enhance its thermal and mechanical properties. In order to improve nanoparticles dispersion, PMMA grafted particles have been prepared by atom transfer radical polymerization (ATRP) from well-defined silica nanoparticles. This strategy was expected to ensure compatibility between both components of the PMMA nanocomposites. TEM analysis have been performed to evaluate the nanosilica dispersion whereas modified and non-modified silica/PMMA nanocomposites thermal stability and mechanical properties have been investigated by both thermogravimetric and dynamical mechanical analysis.     

Influence of silica on shape memory effect and mechanical properties of polyurethane-silica hybrids

Polyurethane block copolymer (PU) was synthesized and was followed by a sol-gel reaction with tetraethoxysilane (TEOS) to prepare high performance polyurethane-silica hybrids with shape memory function. Their tensile and shape memory properties were compared as a function of TEOS content and PU hard segment content. A tensile test showed that the mechanical properties were largely influenced by TEOS content, and the maximum elongation-at-break as well as maximum breaking stress and modulus were obtained when TEOS at 10 wt% was used. Shape memory of hybrids was also obtained from a thermomechanical test, and showed good shape retention and shape recovery of more than 80% for all samples. Consequently, by silica hybridization, an improvement in the mechanical properties and shape recovery force of PU could be achieved without any decrease in their shape recovery effect.     

Pickering stabilization as a tool in the fabrication of complex nanopatterned silica microcapsules

Complex silica-based microcapsules with nanopatterned features were made using Pickering stabilization as a fabrication tool. A sequential two-step liquid-liquid interface-driven assembly process was employed using Laponite clay discs and Laponite armored polystyrene latex particles as solids to stabilize emulsion droplets on two different length scales. The discotic Laponite particles and poly(diethoxysiloxane) were used as silica sources. The ethoxy groups of the poly(diethoxysiloxane) were removed via a triethylamine-catalyzed interfacial hydrolysis and sol-gel reaction. The organic components were removed via a calcination step. The two-stage templating route provided siliceous microcapsules of which the capsule walls were decorated on either the outside or inside with nanocapsules composed of Laponite clay.     

Tuning the electronic properties of N-heterocyclic carbenes

The electron-donating properties of N-heterocyclic carbenes ([N,N'-bis(2,6-dimethylphenyl)imidazol]-2-ylidene and the respective dihydro ligands) with 4,4'-R-substituted aryl rings (4,4'-R=NEt2, OC(12)H(25), Me, H, Br, S(4-tolyl), SO(4-tolyl), SO2(4-tolyl)) were studied. Twelve new N-heterocyclic carbene (NHC) ligands were synthesized as well as the respective iridium complexes [IrCl(cod)(NHC)] and [IrCl(CO)2(NHC)]. Cyclic voltammetry (DeltaE1/2) and IR (nu (CO)) can be used to measure the electron-donating properties of the carbene ligands. Modifying the 4-positions with electron-withdrawing substituents (4-R=-SO(2)Ar, DeltaE1/2=+0.92 V) results in NHC ligands with virtually the same electron-donating capacity as a trialkylphosphine in [IrCl(cod)(PCy3)] (DeltaE1/2 =+0.95 V), while [IrCl(cod)(NHC)] complexes with 4-R=NEt2 (DeltaE1/2= +0.59 V) show drastically more cathodic redox potentials and significantly enhanced donating properties.     

Tuning the optical properties of fluorinated indolylfulgimides

Photochromic fluorinated indolylfulgides have been identified as potential candidates for a wide range of applications including optical switches, photoregulators of biological processes, and optical memory media. In humid environments or biological systems, hydrolytic stability is essential. In an effort to improve hydrolytic stability, a series of indolylfulgimides has been synthesized from a parent trifluoromethyl-substituted indolylfulgide. The nitrogen of the succinimide moiety is linked to either a dimethyl amino or one of seven substituted phenyl groups. The phenyl groups feature substituents with increasing electron-withdrawing ability. The spectral characteristics of each compound have been examined, revealing that the wavelength absorption maxima of each form increases with increasing electron-withdrawing ability of the substituted N-phenyl ring. The quantum yields of the photoreactions have been determined with the N-(phenyl)fulgimide showing a ring closure value of nearly 0.30 in toluene. In addition, the hydrolytic, thermal, and photochemical stabilities of each compound have been measured. The fulgimides exhibit at least a 200-fold enhancement of hydrolytic stability for the Z-form and over a 1000-fold enhancement for the C-form in comparison to the same form of the parent fulgide. The N-(2,3,5,6-tetrafluoro-4-trifluoromethylphenyl)fulgimide can undergo up to 3000 photochemical cycles (coloration followed by bleaching) before losing 20% of its initial absorbance at photostationary state.     

Tuning of the properties of rhodopsin-based molecular switches

The modification of relevant chemical properties of rhodopsin-based molecular photoswitches is presented. We show how both the substituents present and the nitrogen atom quaternization are capable to change the wavelength of absorption and the thermal stability of the photoisomer. Adjusting these properties, the molecular switches could be turned into useful compounds for solar energy storage devices.