Comparison of four extraction/methylation analytical methods to measure fatty acid composition by gas chromatography in meat

Four different extraction-derivatization methods commonly used for fatty acid analysis in meat (in situ or one-step method, saponification method, classic method and a combination of classic extraction and saponification derivatization) were tested. The in situ method had low recovery and variation. The saponification method showed the best balance between recovery, precision, repeatability and reproducibility. The classic method had high recovery and acceptable variation values, except for the polyunsaturated fatty acids, showing higher variation than the former methods. The combination of extraction and methylation steps had great recovery values, but the precision, repeatability and reproducibility were not acceptable. Therefore the saponification method would be more convenient for polyunsaturated fatty acid analysis, whereas the in situ method would be an alternative for fast analysis. However the classic method would be the method of choice for the determination of the different lipid classes.     

pH计检定仪期间核查方法

介绍pH计检定仪的4种期间核查方法:传递比较法、多台对比法、留样测量法、实验室间比对法。传递比较法能直接反应pH计检定仪的变化,适用于已建立pH计检定仪检定装置的单位;多台对比法与留样测量法方便、快捷,可操作性强,适合大多数单位进行pH计检定仪的期间核查;实验室间比对法对设备要求较低,但需要协调的单位较多,周期较长,费用较高,实用性差。     

Disintegration test to measure lot-to-lot variations of vaginal tablets

Attempts were made to investigate the disintegration test for vaginal tablets. Disintegration tests were done for four different commercial vaginal tablets (three lots each) by the watch glass method and Japanese Pharmacopoeia (JP) disintegration method, and the resulting profiles were compared to those by the modified British Pharmacopoeia (BP) method on a point of lot-to-lot variation of the disintegration times. The disintegration time of every tablet by the modified BP method was longest, followed by the watch glass method, and finally by the JP disintegration method. The results for lot-to-lot differences in disintegration times by the modified BP method were similar to those by the watch glass method. However, such lot-to-lot differences as found by the modified BP method and watch glass method were not always observed by the JP disintegration method. It was concluded from these results that the modified BP method was most suitable for investigating lot-to-lot differences in the disintegration of vaginal tablets.     

按独立组元计算复杂化学平衡的方法

本文通过分析独立组元的本质,提出了一个按独立组元来计算复杂化学平衡的方法。这个方法中的未知数和方程数比现有的自由能最小化法、质量作用方程组的方法和反应进度的方法中的未知数和方程数显著减少,因而计算过程大为简化。例如,对于计算一个由3个元素10个组元组成的复杂化学平衡体系来说,若采用其它方法须用电子计算机,而采用独立组元法仅须使用袖珍可编程序计算器即可完成。本文叙述了独立组元法的基本原理和具体方法,并根据理论分析和计算实践,将独立组元法与其它方法的优劣作了对比。     

Crude fat, diethyl ether extraction, in feed, cereal grain, and forage (Randall/Soxtec/submersion method): collaborative study

A method for determining crude fat in animal feed, cereal grain, and forage (plant tissue) was collaboratively studied. Crude fat was extracted from the animal feed, cereal grain, or forage material with diethyl ether by the Randall method, also called the Soxtec method or the submersion method. The proposed submersion method considerably decreases the extraction time required to complete a batch of samples. The increase in throughput is very desirable in the quest for faster turnaround times and the greater efficiency in the use of labor. In addition, this method provides for reclamation of the solvent as a step of the method. The submersion method for fat extraction was previously studied for meat and meat products and was accepted as AOAC Official Method 991.36. Fourteen blind samples were sent to 12 collaborators in the United States, Sweden, Canada, and Germany. The within-laboratory relative standard deviation (repeatability) ranged from 1.09 to 9.26% for crude fat. Among-laboratory (including within) relative standard deviation (reproducibility) ranged from 1.0 to 21.0%. The method is recommended for Official First Action.     

Crude fat, hexanes extraction, in feed, cereal grain, and forage (Randall/Soxtec/submersion method): collaborative study

A method for determining crude fat in animal feed, cereal grain, and forage (plant tissue) was collaboratively studied. Crude fat was extracted from the animal feed, cereal grain, or forage material with hexanes by the Randall method, also called the Soxtec method or the submersion method. The use of hexanes provides for an alternative to diethyl ether for fat extractions. The proposed submersion method considerably decreases the extraction time required to complete a batch of samples compared to Soxhlet. The increase in throughput is very desirable in the quest for faster turnaround times and the greater efficiency in the use of labor. In addition, this method provides for reclamation of the solvent as a step of the method. The submersion method for fat extraction was previously studied for meat and meat products and was accepted as AOAC Official Method 991.36. Fourteen blind samples were sent to 14 collaborators in the United States, Sweden, Canada, and Germany. The within-laboratory relative standard deviation (repeatability) ranged from 1.23 to 5.80% for crude fat. Among-laboratory (including within) relative standard deviation (reproducibility) ranged from 1.88 to 14.1%. The method is recommended for Official First Action.     

聚合物微晶尺寸和晶格畸变

聚合物微晶尺寸和晶格畸变是对聚合物材料性能有着重要影响的结构参数。本文介绍了应用Ｘ射线衍射方法测定聚合物微晶尺寸和结构畸变的几种方法：近似函数、次晶模型法、方差法、矩法。     

Birefringence of highly oriented fibers

A spectrophotometric method was developed for measuring the birefringence of highly oriented synthetic fibers. This method surmounts the low birefringence limit of the standard quartz compensator method and the difficulties in interpretation of the photographic fringe method. A highly oriented aramid fiber gave birefringence values of 0.60–0.75 by this method, compared with 0.25 for polyester and 0.06 for nylon by other conventional methods. The operating principles and excellent results of this new method provide a basis for the extension of routine birefringence characterization to highly oriented fibers.     

Simultaneous determination of imazalil and its major metabolite in citrus fruit by solid-phase extraction and capillary gas chromatography with electron capture detection

A method was developed for the simultaneous determination of imazalil and its major metabolite, R 14821, in citrus fruit. This method (designated the SPE method) is based on solid-phase extraction (SPE) and capillary gas chromatography (GC) with electron-capture detection (ECD). The SPE method is highly sensitive for both compounds (limit of detection for each: 0.001 microg/g) and is less time consuming than the previously reported method based on repeated liquid-liquid partitioning and GC-ECD. Recoveries for 3 levels of fortification (0.02, 0.2, and 2.5 microg/g) from satsuma mandarins ranged from 94.3 to 96.5% for imazalil and from 93.9 to 96.3 % for R 14821, with coefficients of variation (CVs) ranging from 3.1 to 6.3% for imazalil and from 4.5 to 5.6% for R 14821. Average residual levels found in grapefruit, oranges, and lemons by the SPE method and the previously reported method, and the corresponding CVs, were similar.     

Performance of a proposed determinative method for p-TSA in rainbow trout fillet tissue and bridging the proposed method with a method for total chloramine-T residues in rainbow trout fillet tissue

Chloramine-T is an effective drug for controlling fish mortality caused by bacterial gill disease. As part of the data required for approval of chloramine-T use in aquaculture, depletion of the chloramine-T marker residue (para-toluenesulfonamide; p-TSA) from edible fillet tissue of fish must be characterized. Declaration of p-TSA as the marker residue for chloramine-T in rainbow trout was based on total residue depletion studies using a method that used time consuming and cumbersome techniques. A simple and robust method recently developed is being proposed as a determinative method for p-TSA in fish fillet tissue. The proposed determinative method was evaluated by comparing accuracy and precision data with U.S. Food and Drug Administration criteria and by bridging the method to the former method for chloramine-T residues. The method accuracy and precision fulfilled the criteria for determinative methods; accuracy was 92.6, 93.4, and 94.6% with samples fortified at 0.5X, 1X, and 2X the expected 1000 ng/g tolerance limit for p-TSA, respectively. Method precision with tissue containing incurred p-TSA at a nominal concentration of 1000 ng/g ranged from 0.80 to 8.4%. The proposed determinative method was successfully bridged with the former method. The concentrations of p-TSA developed with the proposed method were not statistically different at p < 0.05 from p-TSA concentrations developed with the former method.     

基于生命周期评价技术研究全铁含量测定对环境的影响

利用生命周期评价软件Sima Pro7和环境影响评价模型IMPACT 2002+,通过对化学分析方法的清单分析及计算,评价和比较了3种测定铁矿中全铁含量的化学分析方法(酸溶法、碱熔法、微波消解法)对人类健康、生态质量、气候变化及资源消耗等的影响。发现3个方法对环境的影响主要集中于人类健康危害、气候变化和资源消耗方面。通过计算3种方法的生命周期单一环境负荷值,发现碱熔法、酸溶法和微波消解法的单一环境负荷值分别为1.97,1.81,0.07 m Pt,对环境总体的影响,碱熔法和酸溶法分别为微波消解法的28倍和26倍。单独对人类健康危害指标而言,碱熔法为1.15 m Pt,酸溶法为1.07 m Pt,微波消解法仅为0.039 6 m Pt。碱熔法、酸溶法和微波消解法的碳足迹分别为5.12,4.62,0.189 kg CO_2eq。说明微波消解法排放量最小,其环境友好性最佳,值得推荐。     

Evaluation of a dry, rehydratable film method for rapid enumeration of Staphylococcus aureus

Results with the new 3M Petrifilm Rapid S. aureus Count (RSA) Plate method were compared with those of the classical Baird-Parker agar (BPA) method for detection and enumeration of Staphylococcus aureus. Studies on 219 bacterial strains demonstrated that the Petrifilm RSA plate is more sensitive than and as specific as the classical BPA method for confirmed identification of S. aureus. Counts of colonies from 71 pure cultures, 61 naturally contaminated food samples, and more than 750 artificially inoculated food samples showed that the Petrifilm RSA method was as effective as the classical BPA method for identification and enumeration of S. aureus. The Petrifilm RSA method gave results in one-third the time required for the classical method.     

A combination of the tree-code and IPS method to simulate large scale systems by molecular dynamics

An IPS/Tree method which is a combination of the isotropic periodic sum (IPS) method and tree-based method was developed for large-scale molecular dynamics simulations, such as biological and polymer systems, that need hundreds of thousands of molecules. The tree-based method uses a hierarchical tree structure to reduce the calculation cost of long-range interactions. IPS/Tree is an efficient method like IPS/DFFT, which is a combination of the IPS method and FFT in calculating large-scale systems that require massively parallel computers. The IPS method has two different versions: IPSn and IPSp. The basic idea is the same expect for the fact that the IPSn method is applied to calculations for point charges, while the IPSp method is used to calculate polar molecules. The concept of the IPS/Tree method is available for both IPSn and IPSp as IPSn/Tree and IPSp/Tree. Even though the accuracy of the Coulomb forces with tree-based method is well known, the accuracy for the combination of the IPS and tree-based methods is unclear. Therefore, in order to evaluate the accuracy of the IPS/Tree method, we performed molecular dynamics simulations for 32,000 bulk water molecules, which contains around 10(5) point charges. IPSn/Tree and IPSp/Tree were both applied to study the interaction calculations of Coulombic forces. The accuracy of the Coulombic forces and other physical properties of bulk water systems were evaluated. The IPSp/Tree method not only has reasonably small error in estimating Coulombic forces but the error was almost the same as the theoretical error of the ordinary tree-based method. These facts show that the algorithm of the tree-based method can be successfully applied to the IPSp method. On the other hand, the IPSn/Tree has a relatively large error, which seems to have been derived from the interaction treatment of the original IPSn method. The self-diffusion and radial distribution functions of water were calculated each by both the IPSn/Tree and IPSp/Tree methods, where both methods showed reasonable agreement with the Ewald method. In conclusion, the IPSp/Tree method is a potentially fast and sufficiently accurate technique for predicting transport coefficients and liquid structures of water in a homogeneous system.     

利用电解-化学试剂还原法对高硫煤进行浮选脱硫(英）

通过正交试验,确定了利用电解-化学试剂还原法从高硫煤中浮选脱硫的适宜条件。分析结果表明,经过电解还原浮选煤中的黄铁矿被还原成FeS和S2-,煤的发热量增加,灰分减少。     

The Ampoule Method: A Pathway towards Controllable Synthesis of Electrocatalysts for Water Electrolysis

The ampoule method provides a promising pathway towards the controllable synthesis of novel electrocatalysts for water electrolysis due to its straightforward manipulation of reaction conditions, accessible experimental design, and controlled environment. This Concept introduces the development of the ampoule method and anticipates its application in electrocatalyst synthesis for water electrolysis. First, the history, device configuration, and merits of the ampoule method are briefly introduced. Afterwards, typical materials synthesized by the ampoule method are discussed. Then, recent process in applying the ampoule method to synthesize electrocatalysts for water electrolysis is highlighted. Finally, opportunities and potentials of this method in facilitating electrocatalyst synthesis for water electrolysis are discussed.     

Development of effective Stokesian dynamics method for ferromagnetic colloidal dispersions (cluster-based Stokesian dynamics method)

We have developed a new Stokesian dynamics (SD) method for nondilute colloidal dispersions, which enables us to reduce drastically the computation time. To verify the validity of the present method, which is called the "cluster-based SD method," three-dimensional simulations of a ferromagnetic colloidal dispersion have been carried out for a simple shear flow. The correlation function and viscosity have been evaluated to compare the results obtained by the present method with those obtained by the ordinary SD method and by the method of ignoring hydrodynamic interactions between particles. The results obtained here are summarized as follows. The transient properties from an initial state obtained by the present method agree well with those obtained by the ordinary method, even if a radius r(clstr), which defines the cluster formation, is taken as a small value such as r(clstr)=1.2d (d is the particle diameter). Also, the equilibrium properties such as the pair correlation function and viscosity obtained by the present cluster-based method are in satisfactory agreement with those obtained by the ordinary SD method. Furthermore, the cluster-based method drastically reduces the computation time to about one-fourteenth to one-seventieth that of the ordinary method. It is clear from these results that the cluster-based SD method is significantly superior to the ordinary SD method for ferromagnetic colloidal dispersions for which a large model system such as N=1000 or 10,000 is indispensable in simulations.     

Validated spectrophotometric method for quantitative determination of simvastatin in pharmaceutical formulations and human serum

A simple ultraviolet spectrophotometric method for the determination of simvastatin in methanol has been devised and compared with the existing pharmacopoeial RP-HPLC method for the estimation of the drug. Analytical parameters such as stability, selectivity, accuracy, and precision have been established for the method, using SIMS® tablets and human serum samples, and evaluated statistically to assess the application of the method. The method was validated under ICH and USP guidelines and was found to comprise the advantages for simplicity, stability, sensitivity, reproducibility, and accuracy for use as an alternative to existing nonspectrophotometric methods for the routine determination of the drug in pharmaceutical formulations and for pharmaceutical investigations involving simvastatin.     

Pharmaceutical analysis of some tranquillizers and antidepressants with iodine monochloride

A titrimetric method for the evaluation of some tranquillizers and antidepressants is proposed. The method is based on the oxidation of these drugs by iodine monochloride, in strong acid medium, the iodine liberated being titrated with potassium iodate by the Andrews method. The proposed method is applied successfully for the determination of 9 phenothiazines, 1 thioxanthene, 2 acid hydrazides and 1 dibenzazepine containing a double bond (Opipramol). Tablets, solutions for injection, and drops are also determined by the proposed method. The mechanism of oxidation for each species is suggested and the results obtained agree with these suggestions. Some official and non-official methods for the evaluation of the drugs have been compared with the iodine monochloride method, which is found to be superior in specificity, sensitivity and speed.     

无汞高银低压消解法与氯气校正法测定高氯水体中化学需氧量的比较研究

建立了适合于水和废水中COD测定的新方法--无汞高银低压消解法,以高氯水样为例,对样品中COD含量进行了测定,并与氯气校正法进行了比较验证.结果表明,测定高氯水样中COD,无汞高银低压消解法优于氯气校正法,具有操作简单、测定快速、结果准确、减少二次污染、设备通用等特点.     

Liquid chromatographic determination of pyrantel tartrate in medicated formulations

The validation of a novel liquid chromatographic (LC) method for the determination of pyrantel tartrate in feed is presented. The method provides a significant improvement over the efficiency and precision of AOAC Official Method 978.30. The method was shown to be accurate, precise, linear, and robust for medicated articles. Unlike the official method, the LC method was shown to be a superior stability-indicating method. After the method was validated by using laboratory blends, the effectiveness of the method was demonstrated with marketed product as well.