Electrochemical Determination of Uric Acid Using a Multiwalled Carbon Nanotube Platinum–Nickel Alloy Glassy Carbon Electrode

Platinum–nickel nanoparticles were synthesized by a reduction procedure. The Pt–Ni/C composite was characterized by X-ray diffraction, infrared spectroscopy, transmission electron microscopy, and electrochemical analysis. The measurements show that the Pt–Ni/multiwalled carbon nanotubes provided higher electrocatalytic activity for the oxidation of uric acid than Pt–Ni/carbon black. The sensor prepared from the characterized material provided a long linear dynamic range from 0.1 to 240.4?µM with a detection limit of 0.03?µM and a sensitivity of 41.21?µA?mM^?1?cm^?2. The reported modified electrode also provided excellent selectivity, good stability, and satisfactory reproducibility for the determination of uric acid.     

Silver‐Palladium Nanoalloys Modified Carbon Ionic Liquid Electrode with Enhanced Electrocatalytic Activity Towards Formaldehyde Oxidation

Electrocatalysis of the oxidation of formaldehyde on silver‐palladium‐modified carbon ionic liquid electrode (AgPd/CILE) was investigated in 0.1 M NaOH. The electrochemical performance of the AgPd/CILE was compared with those of Pd/CILE and Ag/CILE. Ag plays an important role in the catalytic performance of AgPd nanocatalyst and yields an excellent antifouling effect. Amperometric measurements showed that AgPd/CILE is a promising sensor for the detection of formaldehyde in the range of 10.0 µM–70.0 mM with a sensitivity of 240.6 µA mM^?1 cm^?2 and a detection limit of 2 µM. The method is free from interference of methanol, ethanol and formic acid.     

Electrochemical nanostructured biosensors: carbon nanotubes versus conductive and semi-conductive nanoparticles

The aim of this work was to demonstrate that various types of nanostructures provide different gains in terms of sensitivity or detection limit albeit providing the same gain in terms of increased area. Commercial screen printed electrodes (SPEs) were functionalized with 100 µg of bismuth oxide nanoparticles (Bi₂O₃ NPs), 13.5 µg of gold nanoparticles (Au NPs), and 4.8 µg of multi-wall carbon nanotubes (MWCNTs) to sense hydrogen peroxide (H₂O₂). The amount of nanomaterials to deposit was calculated using specific surface area (SSA) in order to equalize the additional electroactive surface area. Cyclic voltammetry (CV) experiments revealed oxidation peaks of Bi₂O₃ NPs, Au NPs, and MWCNTs based electrodes at (790 ± 1) mV, (386 ± 1) mV, and (589 ± 1) mV, respectively, and sensitivities evaluated by chronoamperometry (CA) were (74 ± 12) µA mM^?1 cm^?2, (129 ± 15) ±A mM^?1 cm^?2, and (54 ± 2) ±A mM^?1 cm^?2, respectively. Electrodes functionalized with Au NPs showed better sensing performance and lower redox potential (oxidative peak position) compared with the other two types of nanostructured SPEs. Interestingly, the average size of the tested Au NPs was 4 nm, under the limit of 10 nm where the quantum effects are dominant. The limit of detection (LOD) was (11.1 ± 2.8) ±M, (8.0 ± 2.4) ±M, and (3.4 ± 0.1) ±M for Bi₂O₃ NPs, Au NPs, and for MWCNTs based electrodes, respectively.     

Amperometric Glucose Biosensor Based on Ultrafine Platinum Nanoparticles

Abstract

In the present paper the ultrafine and highly dispersed platinum nanoparticles (average size 3 nm) were used for the construction of a glucose biosensor in a simple method. An excellent response to glucose has been obtained with a high sensitivity (137.7 µA mM^?1 cm^?2) and fast response time (5 s). The biosensor showed a detection limit of 5 µM (at the ratio of signal to noise, S/N=3) and a linear range form 0.2 to 3.2 mM with a correlation coefficient r=0.999. The apparent Michaelis–Menten constant (k _m) and the maximum current were estimated to be 9.36 and 1.507 mA mM^?1 cm^?2, respectively. In addition, effects of pH value, applied potential and the interferents on the amperometric response of the sensor were investigated and discussed.     

Electropolymerized Diphenylamine on Functionalized Multiwalled Carbon Nanotube Composite Film and Its Application to Develop a Multifunctional Biosensor

Diphenylamine (DPA) monomers have been electropolymerized on the amino‐functionalized multiwalled carbon nanotube (AFCNT) composite film modified glassy carbon electrode (GCE) by cyclic voltammetry (CV). The surface morphology of PDPA‐AFCNT was studied using field‐emission scanning electron microscopy (FE‐SEM). The interfacial electron transfer phenomenon at the modified electrode was studied using electrochemical impedance spectroscopy (EIS). The PDPA‐AFCNT/GCE represented a multifunctional sensor and showed good electrocatalytic behavior towards the oxidation of catechol and the reduction of hydrogen peroxide. Rotating‐disk electrode technique was applied to detect catechol with a sensitivity of 1360 µA mM^?1 cm^?2 and a detection limit of 0.01 mM. Amperometric determination of hydrogen peroxide at the PDPA‐AFCNT film modified electrode results in a linear range from 10 to 800 µM, a sensitivity of 487.1 µA mM^?1 cm^?2 and detection limit of 1 µM. These results show that the nano‐composite film modified electrode can be utilized to develop a multifunctional sensor.     

Glucose Biosensor Based on Silicon Nitride Nanoparticles

For the first time silicon nitride (Si₃N₄) nanoparticles was used for preparation electrochemical biosensor. GOx immobilized on the Si₃N₄ nanoparticles exhibits facile and direct electrochemistry. The surface coverage and heterogeneous electron transfer rate constant (k_s) of immobilized GOx were 6.3×10^?13 mol cm^?2 and 47.4±0.3 s^?1. The sensitivity, linear concentration range and detection limit of the biosensor for glucose detection were 38.57 µA mM^?1 cm^?2, 25 µM to 8 mM and 6.5 µM, respectively. This biosensor also exhibits good stability, reproducibility and long life time. These indicate Si₃N₄ nanoparticles is good candidate material for construction of third generation biosensor and bioelectronics devices.     

Pt Nanoparticle‐modified Carbon Fiber Microelectrode for Selective Electrochemical Sensing of Hydrogen Peroxide

We report a simple approach to the production of carbon fiber‐based amperometric microbiosensors for selective detection of hydrogen peroxide (H₂O₂), which was achieved by electrometallization of carbon fiber microelectrodes (CFMs) by electrodeposition of Pt nanoparticles. The Pt‐carbon hybrid sensing interface provided a sensitivity of 7711±587 μA ? mM^?1 ? cm^?2, a detection limit of 0.53±0.16 μM (S/N=3), a linear range of 0.8 μM–8.6 mM, and a response time of <2 sec. The morphologies of the Pt nanoparticle‐modified CFMs were characterized by scanning electron microscopy. To achieve selectivity, permseletive layers, polyphenylenediamine (PPD) and Nafion, were deposited resulting in exclusion of the anionic and cationic interferents, ascorbic acid and dopamine, respectively, at their physiologically relevant concentrations. The resultant sensors displayed a sensitivity to hydrogen peroxide of 1381±72 μA ? mM^?1 ? cm^?2, and a detection limit of 0.86±0.19 μM (S/N=3). This simple and rapid metallization method converts carbon fiber microelectrodes, which are readily accessible, to microscale Pt electrodes in 2 min, providing a platform for oxidase‐based amperometric biosensors with improved spatial resolution over more commonly used platinum electrode array microprobes.     

A Simple and Effective Way to Integrate Nile Blue Covalently onto Functionalized SWCNTs Modified GC Electrodes for Sensitive and Selective Electroanalysis of NADH

A simple and new way to assemble Nile blue (NB) covalently onto the surface of functionalized single‐walled carbon nanotubes (f‐SWCNTs) modified glassy carbon (GC) electrode (NB/f‐SWCNTs/GC electrode) was described. The NB/f‐SWCNTs/GC electrode catalyzes effectively the oxidation of NADH with a remarkably decreased overpotential (ca. 700 mV) compared with that at the bare GC. The reaction was found to obey a so‐called Michaelis–Menten kinetics and the related kinetic parameters were determined. This modified electrode possesses promising characteristics as NADH sensor; a wide linear dynamic range of 0.2 to 200 µM, low detection limit of 0.18 µM, fast response time (1–2 s), high sensitivity (24 µA cm⁻² mM⁻¹), anti‐interference ability and anti‐fouling.     

Electrochemical Design of Ultrathin Palladium Coated Gold Nanoparticles as Nanostructured Catalyst for Amperometric Detection of Formaldehyde

An underpotential deposition (UPD) replacement tactic was employed to design a Pd overlayer on gold (Au) nanoparticles electrodeposited on a carbon ionic liquid electrode (CILE). Pd/Au/CILE was applied as an amperometric sensor for the determination of formaldehyde in aqueous solutions. The sensor displayed two linear ranges from 15 µM–1.4 mM and 1.4–56.7 mM of formaldehyde. The limit of detection was 3 µM of formaldehyde and the sensitivity of the sensor was 2.35 µA mM^?1, using the calibration graph in the lower range. The presence of 20 mM of formic acid and methanol and 10 mM ethanol did not interfere with the determination of formaldehyde solution.     

Synthesis and Characterization of Co3O4/Multiwalled Carbon Nanotubes Nanocomposite for Amperometric Sensing of Hydrazine

Co₃O₄ nanoparticles (NPs) were synthesized and decorated on the multi‐walled carbon nanotubes (MWCNTs) through a simple hydrothermal procedure. The deposited Co₃O₄ NPs on the sidewalls of MWCNTs were found to be cubic crystal structure and homogenously dispersed with a narrow particle size distribution centered at around 6 nm. The Co₃O₄/MWCNTs nanocomposite was then utilized for the electrochemical detection of hydrazine, and exhibited a high sensitivity of 34.5 µA mM^?1, a low detection limit of 0.8 µM (S/N=3), a wide linear range of 20 µM to 1.1 mM along with a short response time of less than 5 s.     

Electrodeposition of Three‐Dimensional Porous Platinum Film on Removable Polyaniline Template for High‐Performance Electroanalysis

Three‐dimensional porous platinum (Pt_por) films are prepared based on Pt electrodeposition on polyaniline (PANI) modified electrodes followed by selective dissolution of PANI with HNO₃. Electrochemical quartz crystal microbalance data suggest that the PANI‐H₂PtCl₆ interaction involves redox and coordination reactions, depending on the working potential. The Pt_por shows better electrocatalytic performance than the Pt/PANI and conventionally electrodeposited Pt. The Pt_por modified glassy carbon electrode (GCE) can electrocatalyze the oxidation of H₂O₂ with a sensitivity of 414 µA cm^?2 mM^?1 and a detection limit of 9 nM, and the chitosan‐glucose oxidase/Pt_por/GCE can sense glucose with a sensitivity of 93.4 µA cm^?2 mM^?1.     

An Ethanol Biosensor Based on Simple Immobilization of Alcohol Dehydrogenase on Fe3O4@Au Nanoparticles

An ethanol biosensor based on alcohol dehydrogenase (ADH) attached to Au seeds decorated on magnetic nanoparticles (Fe₃O₄@Au NPs) is presented. ADH was immobilized on Fe₃O₄@Au NPs, which were subsequently fixed by a magnet on a carbon paste electrode modified with 5 % (m : m) MnO₂. Optimum conditions for the amperometric determination of ethanol with the biosensor were as follows: working potential +0.1 V (vs. Ag/AgCl); supporting electrolyte: 0.1 M phosphate buffer solution at pH 6.8 containing 0.25 mM of the coenzyme (NAD⁺); working electrode: carbon paste with magnetically attached Fe₃O₄@Au NPs (0.012 mg ? cm^?2 electrode area) with immobilized alcohol dehydrogenase (120 units per cm² of electrode area). Linearity between signal and concentration was found for the range from 0.1 to 2.0 M ethanol (r²=0.995) with a detection limit of 0.07 M, a sensitivity of 0.02 µA ? mM^?1 ? cm^?2, a reproducibility of 4.0 % RSD, and a repeatability of 2.7 % RSD. The results for the determination of ethanol in alcoholic beverages showed good agreement with gas chromatography (GC) with recovery of 96.0 – 108.8 %.     

A Non‐Enzymatic Hydrogen Peroxide Sensor Based on Gold Nanoparticles/Carbon Nanotube/Self‐Doped Polyaniline Hollow Spheres

In this study, a novel non‐enzymatic hydrogen peroxide (H₂O₂) sensor was fabricated based on gold nanoparticles/carbon nanotube/self‐doped polyaniline (AuNPs/CNTs/SPAN) hollow spheres modified glassy carbon electrode (GCE). SPAN was in‐site polymerized on the surface of SiO₂ template, then AuNPs and CNTs were decorated by electrostatic absorption via poly(diallyldimethylammonium chloride). After the SiO₂ cores were removed, hollow AuNPs/CNTs/SPAN spheres were obtained and characterized by transmission electron microscopy (TEM), field‐emission scanning electron microscopy (FESEM) and Fourier transform infrared spectroscopy (FTIR). The electrochemical catalytic performance of the hollow AuNPs/CNTs/SPAN/GCE for H₂O₂ detection was evaluated by cyclic voltammetry (CV) and chronoamperometry. Using chronoamperometric method at a constant potential of ?0.1 V (vs. SCE), the H₂O₂ sensor displays two linear ranges: one from 5 µM to 0.225 mM with a sensitivity of 499.82 µA mM^?1 cm^?2; another from 0.225 mM to 8.825 mM with a sensitivity of 152.29 µA mM^?1 cm^?2. The detection limit was estimated as 0.4 µM (signal‐to‐noise ratio of 3). The hollow AuNPs/CNTs/SPAN/GCE also demonstrated excellent stability and selectivity against interferences from other electroactive species. The sensor was further applied to determine H₂O₂ in disinfectant real samples.     

Non-enzymatic analysis of glucose on printed films based on multi-walled carbon nanotubes

We report on the fabrication of an enzyme–free electrochemical sensor for glucose based on a printed film consisting of multi–walled carbon nanotubes (MWCNTs). The MWCNT–based film can be produced by means of a flexographic printing process on a polycarbonate (PC) substrate. The electrochemical response of the MWCNT–based film (referred to as MWCNT–PC) towards the oxidation of glucose at pH 7 was studied by means of cyclic voltammetry and electrochemical impedance spectroscopy. The MWCNT–PC film exhibits substantial electrocatalytic activity towards the oxidation of glucose at an anodic potential of 0.30?V (vs. Ag/AgCl). The findings reveal that the MWCNT–PC film enables non–enzymatic sensing of glucose with a detection limit as low as 2.16?μM and a sensitivity of 1045?μA?mM^?1?cm^?2.

High‐Performance Amperometric Sensors Using Catalytic Platinum Nanoparticles‐Thionine‐Multiwalled Carbon Nanotubes Nanocomposite

Thionine (TH) adsorbed on multiwalled carbon nanotubes (MWCNTs) increases the load and dispersion of platinum nanoparticles (PtNPs) generated by chemical reduction of H₂PtCl₆ with NaBH₄. Under the optimum conditions, the PtNPs‐TH‐MWCNTs/Au electrode electrocatalyzed the reduction and oxidation of H₂O₂ with high sensitivity, and after glucose oxidase (GOx) adsorption it responded to glucose concentration with a sensitivity of 0.14 A M^?1 cm^?2. The cyclic voltammetric cathodic peak current for NO₂^? reduction on PtNPs‐TH‐MWCNTs/Au responded linearly to NO₂^? concentration from 0.5 to 150 µM, with a sensitivity of 5.52 A M^?1 cm^?2 and a detection limit of 0.2 µM.     

Electrochemical Fabrication of Cobalt Oxides/Nanoporous Gold Composite Electrode and its Nonenzymatic Glucose Sensing Performance

A nonenzymatic glucose sensor was successfully established by electrochemically decorating cobalt oxides (CoO_x) on a nanoporous gold electrode (NPG) using cobalt hexacyanoferrate (CoHCF) as a precursor. It exhibited high sensitivity and long‐term stability as well as satisfactory quantification of glucose concentration in human serum samples. The morphology and surface analysis of the resulting CoO_x/NPG were carefully characterized. Two detection methods, cyclic voltammetry and amperometry, were employed to evaluate the performance of CoO_x/NPG towards glucose sensing in alkaline solution. Using cyclic voltammetry, at ?0.5 V, the glucose partial oxidation peak current is linear to the glucose concentration up to 14 mM with a sensitivity of 283.7 µA mM^?1 cm^?2. A linear amperometric response at 0.55 V was obtained in the glucose concentration range from 2 µM to 2 mM with a sensitivity of 2025 µA mM^?1 cm^?2 and a response time <3 s.     

Minimally‐invasive Microneedle‐based Biosensor Array for Simultaneous Lactate and Glucose Monitoring in Artificial Interstitial Fluid

Here we report the first mediated pain free microneedle‐based biosensor array for the continuous and simultaneous monitoring of lactate and glucose in artificial interstitial fluid (ISF). The gold surface of the microneedles has been modified by electrodeposition of Au‐multiwalled carbon nanotubes (MWCNTs) and successively by electropolymerization of the redox mediator, methylene blue (MB). Functionalization of the Au‐MWCNTs/polyMB platform with the lactate oxidase (LOX) enzyme (working electrode 1) and with the FAD‐Glucose dehydrogenase (FADGDH) enzyme (working electrode 2) enabled the continuous monitoring of lactate and glucose in the artificial ISF. The lactate biosensor exhibited a high sensitivity (797.4±38.1 μA cm^?2 mM^?1), a good linear range (10–100 μM) with a detection limit of 3 μM. The performance of the glucose biosensor were also good with a sensitivity of 405.2±24.1 μA cm^?2 mM^?1, a linear range between 0.05 and 5 mM and a detection limit of 7 μM. The biosensor array was tested to detect the amount of lactate generated after 100 minutes of cycling exercise (12 mM) and of glucose after a normal meal for a healthy patient (10 mM). The results reveal that the new microneedles‐based biosensor array seems to be a promising tool for the development of real‐time wearable devices with a variety of sport medicine and clinical care applications.     

Direct Voltammetry of Copper,Zinc‐Superoxide Dismutase Immobilized onto Electrodeposited Nickel Oxide Nanoparticles: Fabrication of Amperometric Superoxide Biosensor

Direct electron transfer of immobilized copper, zinc‐superoxide dismutase (SOD) onto electrodeposited nickel‐oxide (NiOx) nanoparticle modified glassy carbon (GC) electrode displays a well defined redox process with formal potential of ?0.03 V in pH 7.4. Cyclic voltammetry was used for deposition of (NiOx) nanoparticles and immobilization of SOD onto GC electrode. The surface coverage (Γ) and heterogeneous electron transfer rate constant (k_s) of immobilized SOD are 1.75×10^?11 mol cm^?2 and 7.5±0.5 s^?1, respectively. The biosensor shows a fast amperometric response (3 s) toward superoxide at a wide concentration range from 10 µM to 0.25 mM with sensitivity of 13.40 nA µM^?1 cm^?2 and 12.40 nA µM^?1 cm^?2, detection limit of 2.66 and 3.1 µM based on anodically and cathodically detection. This biosensor exhibits excellent stability, reproducibility and long life time.     

Electrochemical Sensor for Detection of Glucose Based on Ni@Pt Core‐shell Nanoparticles Supported on Carbon

In this work, Ni@Pt core‐shell nanoparticles with diameter of 3–4 nm and thin Pt shell was synthesized by a successive reduction approach using carbon as support to develop high‐performance non‐enzymatic glucose sensor. The resulting electrochemical sensor displayed good catalytic activity toward glucose oxidation, presenting a high current density of 66.9 µA mM^?1 cm^?2 at an applied potential of ?0.1 V. It showed a wide linear range of 0.1–30.1 mM and the limit of detection was down to 30 µM (S/N=3). Notably, it was found that the proposed sensor exhibited good selectivity to avoid the interference from ascorbic acid, uric acid, fructose and acetamidophenol. Furthermore, the feasibility of the as‐prepared non‐enzymatic glucose sensor in the determination of glucose in serum samples was successfully implemented.     

Electrocatalytic Oxidation of Glucose at Carbon Nanotubes Supported PtRu Nanoparticles and Its Detection

PtRu nanoparticles were supported on multiwall carbon nanotubes (MWNTs), which were further fabricated as an electrode for nonenzymatic glucose sensing. Transmission electron microscope and X‐ray diffraction patterns were used for characterization of the PtRu nanoparticles on MWNTs. Cyclic voltammetry and chronopotentiometry were applied to investigate the performance of the PtRu/MWNTs nanocomposite electrode for nonenzymatic oxidation of glucose. The PtRu/MWNTs electrode shows high electrocatalytic activity towards the oxidation of glucose in 0.1 M NaOH solution and thus can be used to selectively detect glucose. Under the optimal potential (+0.55 V vs. Ag/AgCl), the biosensor effectively performs a selective electrochemical analysis of glucose in the presence of common interferents, such as ascorbic acid (AA), dopamine (DP) and uric acid (UA). Wide linear calibration ranging from 1 mM to 15 mM, high sensitivity of 28.26 μA cm^?2 mM^?1, low detection limit of 2.5×10^?5 M, and fast response time of 10 s were achieved for the detection of glucose at the PtRu/MWNTs electrode.