Flow-field dynamics of the non-reacting and reacting jet in a vitiated cross-flow

The dynamics of a premixed ethylene-air jet injected transverse to a vitiated cross-flow were investigated using high-repetition rate particle image velocimetry (PIV). Both non-reacting and reacting jets were found to be characterized by a dominant frequency associated with the jet wake vortex system. For the isothermal jet, increasing the momentum flux ratio (J) has only a slight effect on the frequency of the oscillation but significantly increases its magnitude. The reacting jet was found to exhibit different behavior, with a monotonic increase in the dominant frequency with J. The jet equivalence ratio (?_j) was found to have little effect on the rate of wake vortex shedding but affects the overall magnitude of the oscillation. Comparison with data reported in the literature suggests the relationship between the wake Strouhal number (St_w) and J is fuel dependent. Application of a vortex detection algorithm shows a stark difference in the location of the wake vortices under non-reacting and reacting conditions. Under isothermal conditions, the vortices are found close to the jet centerline and dissipate relatively quickly. Reaction confines the vortices to a narrow shear layer until a farther distance downstream and the vortices convect through the entire area of interest. Additionally, the vortex circulation strength was found to increase with J. Proper orthogonal decomposition (POD) analysis of the non-reacting and reacting jets demonstrates the dominance of the wake vortex structures in the oscillating flow fields. In both cases, the temporal information extracted from the most energetic modes is identical to the dominant frequencies measured in the flow fields. The primary effect of heat release is to reduce the overall amount of coherence and to delay the appearance of elevated coherence levels until a larger streamwise distance from the jet exit.     

Unsteady wake vortices in jets in cross-flow

Abstract  

The current flow visualization study investigates unsteady wake vortices of jets in cross-flow in order to (1) advance the understanding of their origin and characteristics and (2) explore various excitation techniques for organizing and accentuating them. An isolated circular jet passed through a nozzle and entered the cross-flow normal to the wall. Free stream velocities up to 5 m/s and jet-to-cross-flow velocity ratio range between 1 and 10 were covered. While mechanical perturbation did not result in any significant periodic organization of the wake vortices, the database obtained for the unperturbed flow provided further insight into their behavior. The key finding was that the wake vortices always originated from the lee-side of the jet where the jet efflux boundary layer and the wall boundary layer intersected. In no case these vortices were seen to form either from the wall boundary layer or the jet shear layer at downstream locations. After formation the wake vortex twists and stretches as it convects downstream with the base still attached to the near-wall region on the jet’s lee side. The top remains connected to the underside of the jet where the tracer particles dissipate due to high turbulence in the shear layer.     

PIV studies of large scale structures in the near field of small aspect ratio elliptic Jets

The near flow field of small aspect ratio elliptic turbulent free jets (issuing from nozzle and orifice) was experimentally studied using a 2D PIV Two point velocity correla tions in these jets revealed the extent and orientation of the large scale structures in th e major and minor planes. The spatial filtering of the instantaneous velocity field using Gaussian convolution kernel shows that while a single large vortex ring circumscribing the jet seems to be present at the exit of nozzle, the orifice jet exhibited a number of smaller vortex ring pairs close to jet exit. The smaller length scale observed in the case of the orifice jet is rep resentative of the smaller azimuthal vor tex rings that generate axial vortex field as they are convected. This results in the axis-switching in th e case of orifice jet and may have a mechanism differ ent from the self induction process as observed in the case of contoured nozzle jet flow.     

Random vortex-street model for a self-similar plane turbulent jet

We ask what determines the (small) angle of turbulent jets. To answer this question we first construct a deterministic vortex-street model representing the large-scale structure in a self-similar plane turbulent jet. Without adjustable parameters the model reproduces the mean velocity profiles and the transverse positions of the large-scale structures, including their mean sweeping velocities, in a quantitative agreement with experiments. Nevertheless, the exact self-similar arrangement of the vortices (or any other deterministic model) necessarily leads to a collapse of the jet angle. The observed (small) angle results from a competition between vortex sweeping tending to strongly collapse the jet and randomness in the vortex structure, with the latter resulting in a weak spreading of the jet.     

Quasi-radial wall jets as a new concept in boundary layer flow control

This work aims to introduce a novel concept of wall jets wherein the flow is radially injected into a medium through a sector of a cylinder, called quasi-radial (QR) wall jets. The results revealed that fluid dynamics of the QR wall jet flow differs from that of conventional wall jets. Indeed, lateral and normal propagations of a conventional three-dimensional wall jet are via shear stresses. While, lateral propagation of a QR wall jet is due to mean lateral component of the velocity field. Moreover, discharged Arrays of conventional three-dimensional wall jets in quiescent air lead to formation of a combined wall jet at large distant from the nozzles, while QR wall jet immediately spread in lateral direction, meet each other and merge together very quickly in a short distance downstream of the jet nozzles. Furthermore, in discharging the conventional jets into an external flow, there is no strong interaction between them as they are moving parallel. While, in QR wall jets the lateral components of the velocity field strongly interact with boundary layer of the external flow and create strong helical vortices acting as vortex generators.     

Turbulence and heat excited noise sources in single and coaxial jets

The generation of noise in subsonic high Reynolds number single and coaxial turbulent jets is analyzed by a hybrid method. The computational approach is based on large-eddy simulations (LES) and solutions of the acoustic perturbation equations (APE). The method is used to investigate the acoustic fields of one isothermal single stream jet at a Mach number 0.9 and a Reynolds number 400,000 based on the nozzle diameter and two coaxial jets whose Mach number and Reynolds number based on the secondary jet match the values of the single jet. One coaxial jet configuration possesses a cold primary flow, whereas the other configuration has a hot primary jet. Thus, the configurations allow in a first step the analysis of the relationship of the flow and acoustic fields of a single and a cold coaxial jet and in a second step the investigation of the differences of the fluid mechanics and aeroacoustics of cold and hot coaxial jets. For the isothermal single jet the present hybrid acoustic computation shows convincing agreement with the direct acoustic simulation based on large-eddy simulations. The analysis of the acoustic field of the coaxial jets focuses on two noise sources, the Lamb vector fluctuations and the entropy sources of the APE equations. The power spectral density (PSD) distributions evidence the Lamb vector fluctuations to represent the major acoustic sources of the isothermal jet. Especially the typical downstream and sideline acoustic generations occur on a cone-like surface being wrapped around the end of the potential core. Furthermore, when the coaxial jet possesses a hot primary jet, the acoustic core being characterized by the entropy source terms increases the low frequency acoustics by up to 5 dB, i.e., the sideline acoustics is enhanced by the pronounced temperature gradient.     

Helical modes in low- and high-swirl jets measured by tomographic PIV

We report on a parallel study on properties of large-scale vortical structures in low- and high-swirl turbulent jets by means of the time-resolved tomographic particle image velocimetry technique. The high-swirl jet flow is featured by a well-established bubble-type vortex breakdown with a central recirculation zone. In the low-swirl flow, the mean axial velocity, while intermittently acquiring negative values, remains positive in the mean but with a local velocity defect immediately downstream from the nozzle exit, followed by a spiralling vortex core system and its eventual breakdown. Measurements of the 3D velocity fields allowed direct analysis of the azimuthal/helical modes via Fourier transform over the azimuthal angle and proper orthogonal decomposition (POD) analysis in the Fourier space. A precessing vortex core is detected for both swirl cases, whereas the POD analysis showed that the one originating in the bubble-type vortex breakdown is much more energetic and easier to detect.     

Flow and Heat Transfer Characteristics of in-Line Impinging Jets With Cross-Flow At Short Jet-To-Plate Distance

The aim of this research is to numerically and experimentally study the flow and heat transfer characteristics of in-line impinging jets in cross-flow. The jets from a row of round orifices are perpendicularly impinged on the inner surface of a rectangular wind tunnel at a short distance between the orifice plate and impinged surface (H) of 2D, where D is a diameter of the orifice. The jet velocity was fixed corresponding to Re = 13,400 for all experiments, and the cross-flow velocity was varied at three different velocity ratios (velocity ratio, jet velocity/cross-flow velocity) of 3, 5, and 7. The heat transfer characteristic was visualized using a thermochromic liquid crystal sheet, and the Nusselt number distribution was evaluated by an image processing technique. The flow pattern on the impinged surface was also visualized by an oil film technique. The numerical simulation was used to explore a flow interaction between the impinging jets and cross-flow. The results indicated that Nusselt number peak increased by the increasing cross-flow velocity for short jet-to-plate distance. For the range determined, the maximum local Nusselt number peak was obtained at VR = 3 as the consequence of high velocity and high turbulence kinetic energy of jet impingement.     

Large-eddy simulation of impinging jets on smooth and rough surfaces

We performed large-eddy simulations (LES) of forced impinging jets over smooth and rough surfaces, containing large-scale, azimuthal vortices generated by the enhanced primary instability in the jet shear layer. The interaction between these vortices and the turbulence in the wall jet that is formed downstream of the impingement region determines their rate of decay. To explore the surface-roughness effects on the evolution of the vortices, sand-grain-like surfaces are generated using uniformly distributed but randomly oriented ellipsoids. The flow is compared to our previous LES of jets impinging on a smooth surface. In spite of the severe modification caused by the roughness on the near-wall flow, the vortex development is not significantly altered. Slightly faster decay of the primary vortices is observed in the rough-wall case compared to the smooth-wall one; the secondary vortex that detaches from the wall and is lifted up has larger vorticity. The highly disturbed near-wall flow is advected outward and affects the evolution of the primary vortex for a longer period during the vortex interaction. The robust turbulent generation mechanism in the outer shear layer, however, mitigates the changes in vortex behaviour. The momentum deficit and the enhancement of turbulence due to the surface roughness play a key role during this process.     

Temperature field measurement of an array of laminar premixed slot flame Jets using Mach-Zehnder interferometry

An experimental study was performed to investigate the influence of Reynolds number (Re) and non-dimensional jet-to-jet spacing (S/D_h) on flame shape, structure and temperature field of an array of laminar premixed slot flame jets. Mach-Zehnder interferometry technique is used to obtain an insight to the overall temperature field between single, twin and triple slot flame jets. The slot jets with large aspect ratio (L/W), length of L=60 mm and width of W=6 mm were used to eliminate the three-dimensional effect of temperature field. The effect of jet-to-jet spacing was investigated on flame characteristics under the test conditions of 200≤Re≤400 and equivalence ratio (φ) of unity. The present measurement reveals that the variation of maximum flame temperature with increment of Reynolds number is mainly due to heat transfer effects and is negligible while the flame height is increased. For the cases of twin and triple flame jets by increasing Reynolds number and decreasing non-dimensional jet-to-jet spacing (S/D_h), the interferences between the jets are increased and the jets attracted each other. Strong interference was observed at S/D_h=1.15. For the case of triple jets at this S/D_h, the central jet was suppressed while the side jets deflected towards the inner jet. The interference between jets was found to reduce the heat flux in the jet-to-jet interacting zone due to incomplete combustion. Also the optimum jet-to-jet spacing of triple flame jets is obtained at each Reynolds number to enhance the heat transfer performance of the jets.     

Experimental examination of vortex-sound generation in an organ pipe: A proposal of jet vortex-layer formation model

Aero-dynamical models of sound generation in an organ pipe driven by a thin jet are investigated through an experimental examination of the vortex-sound theory. An important measurement requirement (acoustic cross-flow as an irrotational potential flow reciprocating sinusoidally) from the vortex-sound theory is carefully realized when the pipe is driven with low blowing pressures of about 60 Pa (jet velocities of about 10 m/s). Particle image velocimetry (PIV) is applied to measure the jet velocity and the acoustic cross-flow velocity over the mouth area at the same phase by quickly switching the jet drive and the loudspeaker-horn drive. The vorticity of the jet flow field and the associated acoustic generation term are evaluated from the measurement data. It is recognized that the model of the “jet vortex-layer formation” is more relevant to the sound production than the vortex-shedding model. The acoustic power is dominantly generated by the flow–acoustic interaction near the edge, where the acoustic cross-flow velocity takes larger magnitudes. The acoustic generation formula on the vortex sound cannot deny the conventional acoustical volume-flow model because of the in-phase relation satisfied between the acoustic pressure at the mouth and the acoustic volume flow into the pipe. The vortex layers formed along both sides of the jet act as the source of an accelerating force (through the “acceleration unbalance”) with periodically alternating direction to oscillate the jet flow and to reinforce the acoustic cross-flow at the pipe mouth.     

Roles of initial condition and vortex pairing in jet noise

This is a study of the effect of initial condition on sound generated by vortex pairing in a low Mach number, cold air jet (0·15 ⩽ M ⩽ 0·35). Data has been taken, both flow velocity fields and sound pressure far fields, in a quality anechoic facility, with careful documentation of the effect of initial condition on the sound field of jets of two different geometries (i.e., circular and elliptic). Explanations are presented for most of the observed effects by applying Möhring's theory of vortex sound to vortex filament models of coherent structures in the jets. The explanations also draw upon experience with coherent structure dynamics. The sound source of interest here is that associated with the pairing of shear layer vortices. The evolution of these vortices is greatly affected by the initial condition as is their resultant sound field. The elliptic jets with laminar boundary layers show azimuthal directivity, namely, sound pressure levels in the minor axis plane were greater than in the major axis plane. This difference decreases as the nozzle boundary layer undergoes natural transition with increasing jet speed. When the nozzle boundary layer is tripped, making it fully turbulent and removing the shear layer mode of pairing, the elliptic jet sound fields become nearly axisymmetric. What appears to be the most acoustically active phase of vortex pairing has been modeled, and the resulting sound field calculated for the circular jet. Supporting evidence is found in the experimental data for the validity of this model. The model explains the connection between the initial condition and the far field sound of jets. Interestingly, a general result of Möhring's theory is that motions of vortex rings (of any arbitrary shape) can produce only axisymmetric sound fields if the rings remain in a plane. This implies that the observed asymmetric directivity of the laminar elliptic jet sound field must be due to non-planar ring motions of the vortical structures. The primary contribution of this paper is to examine quantitatively the role of vortex pairing in the production of jet noise; the results are used to reemphasize that “pairing noise” cannot be dominant in most practical jet sound fields, contrary to claims by other researchers.     

Flow and mixing fields of turbulent bluff-body jets and flames

The mean structure of turbulent bluff-body jets and flames is presented. Measurements of the flow and mixing fields are compared with predictions made using standard turbulence models. It is found that two vortices exist in the recirculation zone; an outer vortex close to the air coflow and an inner vortex between the outer vortex and the jet. The inner vortex is found to shift downstream with increasing jet momentum flux relative to the coflow momentum flux and gradually loses its circulation pattern. The momentum flux ratio of the jet to the coflow in isothermal flows is found to be the only scaling parameter for the flow field structure. Three mixing layers are identified in the recirculation zone. Numerical simulations using the standard k-? and Reynolds stress turbulence models underpredict the length of the recirculation zone. A simple modification to the C₁ constant in the dissipation transport equation fixes this deficiency and gives better predictions of the flow and mixing fields. The mixed-is-burnt combustion model is found to be adequate for simulating the temperature and mixing field in the recirculation zone of the bluff-body flames.     

圆管潜射流生成偶极子涡特性实验

利用溢流恒压装置产生具有稳定出流速度的圆管潜射流, 结合染色液流态显示方法, 在多种射流无量纲潜深d/H、雷诺数Re以及限制数C的组合下, 实验研究了该潜射流动量在有限深密度均匀流体中的演化特性, 其中d为射流潜深, H为水深. 研究表明, 当C<1时潜射流表现为深水特征, 而当1≤ C<2时潜射流表现为过渡特征, 在这两种情况下均不产生任何形式的大尺度相干结构; 当2≤ C<10时潜射流表现为浅水特征, 而C≥10时潜射流表现为极浅水特征, 在这两种情况下均产生大尺度的偶极子涡结构. 对极浅水特征潜射流, 在各种无量纲潜深下, 偶极子涡结构的无量纲形成时间t_f^*与无量纲射流时间T_inj^*均满足相同的正比例关系; 对浅水特征潜射流, 当d/H=0.5时, t_f^*与T_inj^*满足某种线性关系, 但对其他无量纲潜深, t_f^*与T_inj^*之间无明显规律. 关键词： 圆管潜射流 限制数 偶极子涡结构 形成时间     

A study in the developing region of square jet

The developing region of a turbulent square jet is investigated using high-resolution particle image velocimetry (PIV). The mean velocity and turbulence stresses are presented in various horizontal planes, along the jet centerline covering the initial region of the jet as well as the transition to the self-similar region. To study the flow structure away from the central plane, velocity measurements in two additional horizontal planes, one located halfway from the jet central plane toward the edge and the other at the edge of the square jet, are also examined. Analysis of the instantaneous velocity fields reveal the presence of an arrow-like feature in the square jet due to the higher instability generated in the jet shear layer compared with a round jet. To elucidate the imprints of the vortex structures present in the jets, a swirling strength-based vortex identification methodology is applied on a large ensemble of instantaneous velocity fields. Statistical analysis of the number of vortex cores, and their size and rotational strength in the measurement plane is undertaken. Vortex population at the edge was found to be very different compared with that in the central plane.     

A numerical study of rotation effects on jets effusing from inclined holes into a cross-flow

In this work, the complexity of the flow field arising from the impact of the interaction of coolant jets with a hot cross-flow under rotation conditions was numerically simulated using large eddy simulation with artificial inflow boundary condition. The finite-volume method and the unsteady PISO (Pressure Implicit with Splitting of Operators) algorithm were applied on a non-uniform staggered grid. The simulations were performed for four different values of rotation number (Ro) of 0.0, 0.03021, 0.06042, and 0.12084, a jet Reynolds number of 4700, based on the hole width and the jet exit velocity. The air jet was injected at 30° and 90° in the streamwise direction with a density ratio of 1.04 and a velocity ratio of 0.5. The flow fields of the present study were compared with experimental data in order to validate the reliability of the LES technique. It was shown that the rotation has a strong impact on the jet trajectory behaviour and the film cooling effectiveness. The film trajectory always inclines centrifugally. Under rotating conditions, the film trajectory departs from the centreline to the left boundary. The deflection becomes greater as Ro increases. Furthermore, it was also found that the injection angle has a strong impact on separation and reattachment behaviour as well as the strength of the penetration into the cross-flow. As it increases, the distribution of the film cooling downstream the jet exit is more non-uniform and the film cooling effectiveness level slightly decreases.     

Flow visualization of vortex structure of an excited coaxial jet

This paper describes the results of experimental and numerical studies concerning the near-field vortical structure and dynamics of a coaxial jet. The effect of excitation of annular and circular jets on the vortical structure in the inner and outer shear-layers was studied. The flow visualization and the measurements of mean and fluctuating velocities, by a hot-film probe and the particle image velocimetry (PIV) technique, were carried out in an open water tank. The results of flow visualization and numerical simulation are in good agreement. With the excitation of a half of the initial vortex frequency, it is found that the vortex-pairing event is promoted by the forced excitation and it results in the rapid expansion of the jet width and the increase of velocity fluctuation and the entrainment rate. For the velocity ratio near unity, the dominant peak frequency coincides with the initial vortex frequency, i.e., the lip wake vortex frequency, independent of the forced excitation frequency.     

Experimental investigation on laminar separation control for flow over a two-dimensional bump

The laminar boundary layer separation flow over a two-dimensional bump controlled by synthetic jets is experimentally investigated in a water channel with hydrogen-bubble visualisation and particle image velocimetry (PIV) techniques. The two-dimensional synthetic jet is applied near the separation point. Two Reynolds numbers (Re = 700 and 1120) based on the bump height and free-stream velocity are adopted in this experiment, and seven different excitation frequencies at each Reynolds number are considered, focusing on the separation control as well as the vortex dynamics. The experimental results show that the optimal control can only be achieved within some excitation frequencies at both Reynolds numbers. However, beyond this range, further increasing the excitation frequency leads to an increase in the separation region. The proper orthogonal decomposition (POD) technique and vortex identification by swirling strength (Λ_ci) are applied for the deeper analysis of the separated flow. The reconstructed Λ_ci field by the first four POD modes is used and vortex lock-on phenomenon is observed. It is found that the negative synthetic jet vortex with clockwise rotation draws the separated wake shear layer as it is convected downstream, and then they syncretise together. Thus, the new vortex is induced and shedding downstream periodically.     

射流式氧发生器的三维模拟研究

实现了对射流式氧发生器的三维仿真模拟,给出了氧发生器内部流场结构、各组分的分布状态等信息。研究了射流孔结构对氧发生器性能的影响。指出即便是具有相同比表面积的不同射流孔排布方式,也会对发生器性能产生影响。此外,逆向射流式氧发生器反应器中气体从双侧进入对于减小发生器对气体的阻力具有重要作用。     

Coherent structures of the near field flow in a self-oscillating physical model of the vocal folds

Current theories of voice production depend critically upon knowledge of the near field flow which emanates from the glottis. While most modern theories predict complex, three-dimensional structures in the near field flow, few investigations have attempted to quantify such structures. Using methods of flow visualization and digital particle image velocimetry, this study measured the near field flow structures immediately downstream of a self-oscillating, physical model of the vocal folds, with a vocal tract attached. A spatio-temporal analysis of the structures was performed using the method of empirical orthogonal eigenfunctions. Some of the observed flow structures included vortex generation, vortex convection, and jet flapping. The utility of such data in the future development of more accurate, low-dimensional models of voice production is discussed.