Liquid phase formation of alkyl- and perfluoro-phosphonic acid derived monolayers on magnesium alloy AZ31 and their chemical properties

Alkyl- and perfluoro-phosphonic acid derived SAMs were successfully formed on Mg alloy by liquid phase method for the first time. The chemical and anticorrosive properties of the prepared SAMs on magnesium alloys were characterized using contact angle measurements, X-ray photoelectron spectroscopy (XPS), atomic force microscopy (AFM), and electrochemical measurements. Water contact angle measurements revealed that the maximum advancing/receding water contact angles of n-octyl (OP: CH(3)(CH(2))(7)PO(OH)(2)), n-dodecyl (DP: CH(3)(CH(2))(11)PO(OH)(2)), n-octadecyl (ODP: CH(3)(CH(2))(17)PO(OH)(2)) phosphonic acid, and 2-(perfluorohexyl)ethyl (PFEP: CF(3)(CF(2))(5)CH(2)CH(2)PO(OH)(2)) phosphonic acid were 105.1/64.7°, 108.3/69.6°, 111.9/75.2°, and 115.2/67.4° respectively. In the case of alkylphosphonic acid SAMs (OP, DP, and ODP), the advancing and receding water contact angles increased with an increase in the preparation time. The angle-resolved XPS (AR-XPS) data revealed that the film thicknesses of the OP, DP, ODP, PFEP on Mg alloy were estimated to be 0.8, 1.2, 1.7, and 1.1 nm, respectively. The XPS O 1s data support that the phosphonic acid derived SAM is covalently bound to the oxide or hydroxide surface of the Mg alloy in a monodenate or bidenate manner. Chemical stability of the alkyl- and perfluoro-phosphonic acid modified Mg alloy surfaces was investigated using aqueous solutions at pH=4.0, 7.0, and 10.0. The contact angles of OP, DP, and PFEP modified Mg surface decreased rapidly within the first 5 min after immersion in all the aqueous solutions and were less than 20°. On the other hand, the contact angles of the ODP modified Mg alloy after immersion in aqueous solutions at pH 4, 7 and 10 for 5 min were 45.1°, 89.3,° and 85.5°, respectively. The ODP modified Mg alloy had highest chemical stability in four types of the phosphonic acid derived SAMs used in this study, indicating that the molecular density of ODP on Mg alloy would be higher than those of OP, DP, PFEP on Mg alloy. The corrosion resistance of ODP modified Mg alloy was investigated by potentiodynamic polarization curve measurements. The ODP modified Mg alloy exhibits protective properties in a solution containing Cl(-) ions compared to unmodified Mg alloy.     

In-situ characterization of self-assembled monolayers of water-soluble oligo(ethylene oxide) compounds

In-situ spectroscopic ellipsometry (SE) was utilized to examine the formation of the self-assembled monolayers (SAMs) of the water-soluble oligo(ethylene oxide) [OEO] disulfide [S(CH(2)CH(2)O)(6)CH(3)](2) {[S(EO)(6)](2)} and two analogous thiols - HS(CH(2)CH(2)O)(6)CH(3) {(EO)(6)} and HS(CH(2))(3)O(CH(2)CH(2)O)(5)CH(3) {C(3)(EO)(5)} - on Au from aqueous solutions. Kinetic data for all compounds follow simple Langmuirian models with the disulfide reaching a self-limiting final state (d=1.2nm) more rapidly than the full coverage final states of the thiol analogs (d=2.0nm). The in-situ ellipsometric thicknesses of all compounds were found to be nearly identical to earlier ex-situ ellipsometric measurements suggesting similar surface coverages and structural models in air and under water. Exposure to bovine serum albumin (BSA) shows the self-limiting (d=1.2nm) [S(EO)(6)](2) SAMs to be the most highly protein resistant surfaces relative to bare Au and completely-formed SAMs of the two analogous thiols and octadecanethiol (ODT). When challenged with up to near physiological levels of BSA (2.5mg/mL), protein adsorption on the final state [S(EO)(6)](2) SAM was only 3% of that which adsorbed to the bare Au and ODT SAMs.     

Platelet compatibility improvement by proper choice of acidic terminal functionality for mixed-charge self-assembled monolayers

In this study two different series of mixed-charge self-assembled monolayers (SAMs) prepared with -N(+)(CH(3))(3)-terminated alkanethiol and strong dissociated monovalent -SO(3)H acid-terminated or weaker dissociated divalent -PO(3)H(2) acid-terminated alkanethiol in pure ethanol were characterized. The influence of the acidity of the anionic functionality in the mixed-charge SAMs on the surface characteristics and platelet compatibility was investigated. X-ray photoelectron spectroscopy indicated that a nearly equivalent amount of countercharged terminal groups was noted on the surface of -SO(3)H/-N(+)(CH(3))(3) mixed SAMs, while "-N(+)(CH(3))(3) thiol poor" phenomena were found on -PO(3)H(2)/-N(+)(CH(3))(3) mixed SAMs instead. This was caused by the distinct differences in solvation capability between the acidic anionic functional groups and solvent molecules and/or the interactions among the terminal ends of the thiols. This acidity difference also affected other interfacial properties and the platelet compatibility. The mixed SAMs formed from the mixture of -SO(3)H- and -N(+)(CH(3))(3)-terminated thiols showed higher surface hydrophilicity and exhibited the least amount of platelets adhered, but these two mixed SAMs were all fairly negatively surface charged. The structure of the hydration layer near the surfaces was likely affected by the acidity of the anionic functionality, and this would cause such a distinct behavior in platelet compatibility. It was concluded that the hydrophilic surfaces with nearly equal amounts of surface positively and negatively charged components could exhibit better platelet compatibility. This work demonstrated that the nature of the acidic terminal ends of alkanethiol is also a key factor for preparing mixed-charge SAMs with good platelet compatibility.     

Hydration and dewetting near fluorinated superhydrophobic plates

The water dynamics near nanoscale fluorinated (CF(3)(CF(2))(7)(CH(2))(2)SiH(3)) monolayers (plates) as well as possible dewetting transitions in-between two such plates have been studied with molecular dynamics simulations in this paper. A "weak water depletion" is found near the single fluorinated surface, with an average water density in the first solvation shells 6-8% lower than its hydrogenated counterpart. The fluorinated molecules are also found to be water impermeable, consistent with experimental findings. More surprisingly, a dewetting transition is found in the interplate region with a critical distance D(c) of 10 A (3-4 water diameters) for double plates with 8 x 8 molecules each (plate size approximately 4 nm x 4 nm). This transition, although occurring on a microscopic length scale, is reminiscent of a first-order phase transition from liquid to vapor. The unusual superhydrophobicity of fluorocarbons is found to be related to their larger size (or surface area) as compared to hydrocarbons, which "dilutes" their physical interactions with water. The water-plate interaction profile shows that the fluorinated carbons have a 10-12% weaker water-plate interaction than their hydrogenated counterparts in the nearest solvation shell, even though the fluorocarbons do have a stronger electrostatic interaction with water due to their larger partial charges. However, the van der Waals interactions dominate the water-plate interaction within the nearest shell, with up to 90% contributions to the total interaction energy, and fluorocarbons have a noticeably weaker (by 10-15%) van der Waals interaction with water in the nearest shell than do hydrocarbons. Both the slightly weaker water-plate interaction and larger surface area contribute to the stronger dewetting transition in the current fluorinated carbon plates.     

Mixed azide-terminated monolayers: a platform for modifying electrode surfaces

We have prepared and characterized mixed self-assembled monolayers (SAM) on gold electrodes from azido alkane thiols and various omega-functionalized alkane thiols. In the presence of copper(I) catalysts, these azide-modified surfaces are shown to react rapidly and quantitatively with terminal acetylenes forming 1,2,3-triazoles, via "click" chemistry. The initial azide substituents can be identified and monitored using both grazing-angle infrared (IR) and X-ray photoelectron spectrosopies. Acetylenes possessing redox-active ferrocene substituents react with the azide-terminated mixed SAMs and electrochemical measurements of the ferrocene-modified SAM electrodes have been used to quantify the redox centers attached to these platforms. Time-resolved electrochemical measurements have enabled us to follow the formation of these ferrocene centers and thus to measure the rate of the surface "click" reaction. Under optimal conditions this well-behaved second-order reaction takes place with a rate constant of 1 x 10(3) M(-)(1) s(-)(1). Typical reaction times of several minutes were realized using micromolar concentrations of acetylene. These techniques have been used to construct well-characterized, covalently modified monolayers that can be employed as functional electrode surfaces.     

The role of surface free energy on the formation of hybrid bilayer membranes

The interaction of small phospholipid vesicles with well-characterized surfaces has been studied to assess the effect of the surface free energy of the underlying monolayer on the formation of phospholipid/alkanethiol hybrid bilayer membranes (HBMs). The surface free energy was changed in a systematic manner using single-component alkanethiol monolayers and monolayers of binary mixtures of thiols. The binary surfaces were prepared on gold by self-assembly from binary solutions of the thiols HS-(CH(2))(n)()-X (n = 11, X = CH(3) or OH) in THF. Surface plasmon resonance (SPR), electrical capacitance, and atomic force microscopy (AFM) measurements were used to characterize the interaction of palmitoyl,oleoyl-phosphatidylcholine (POPC) vesicles with the surfaces. For all surfaces examined, it appears that the polar part of surface energy influences the nature of the POPC assembly that associates with the surface. Comparison of optical, capacitance, and AFM data suggests that vesicles can remain intact or partially intact even at surfaces with a contact angle with water of close to 100 degrees. In addition, comparison of the alkanethiols of different chain lengths and the fluorinated compound HS-(CH(2))(2)-(CF(2))(8)-CF(3) that characterize with a low value of the polar part of the surface energy suggests that the quality of the underlying monolayer in terms of number of defects has a significant influence on the packing density of the resulting HBM layer.     

Interaction Forces between Hydrophobic and Hydrophilic Self-Assembled Monolayers

An investigation is presented of the interaction of charged self-assembled monolayers (SAMs) with a monoprotic ionizable acid functional group (-COOH) and uncharged SAMs with a methyl terminated functional group (-CH(3)). The strength of the interactions are determined using an atomic force microscope. For all electrolyte conditions investigated the interactions are not well described by a summation of van der Waals attractions and electrostatic repulsions in a manner suggesting that van der Waals attractions are screened. The repulsions are accurately described as corresponding to two surfaces of different charge interacting with surface charges that are independent of separation (i.e., the constant charge model). A small adhesion force was observed under all conditions and its magnitude increased with NaCl concentration. Copyright 2000 Academic Press.     

Adsorption and wetting characterization of hydrophobic SBA-15 silicas

This work describes adsorption and wetting characterization of hydrophobic ordered mesoporous silicas (OMSs) with the SBA-15 motif. Three synthetic approaches to prepare hydrophobic SBA-15 silicas were explored: grafting with (1) covalently-attached monolayers (CAMs) of C(n)H(2)(n+1)Si(CH(3))(2)N(CH(3))(2), (2) self-assembled monolayers (SAMs) of C(n)H(2)(n+1)Si(OEt)(3), and (3) direct ("one-pot") co-condensation of TEOS with C(n)H(2)(n+1)Si(OEt)(3) in presence of P123 (n=1-18). The materials prepared were characterized by nitrogen adsorption, TEM, and chemical analysis. The surface properties of the materials were assessed by water contact angles (CAs) and by BET C constants. The results showed that, while loadings of the alkyl groups (%C) were comparable, the surface properties and pore ordering of the materials prepared through different methods were quite different. The best quality hydrophobic surfaces were prepared for SBA-15 grafted with CAMs of alkylsilanes. For these materials, the water CAs were above ～120°/100° (adv/rec) and BET C constants were in the range of ～15-25, indicating uniform low-energy surfaces of closely packed alkyl groups on external and internal surfaces of the pores respectively. Moreover, surfaces grafted with the long-chained (C(12)-C(18)) silanes showed super-hydrophobic behavior (CAs～150-180°) and extremely low adhesion for water. The pore uniformity of parental SBA-15 was largely preserved and the pore volume and pore diameter were consistent with the formation of a single layer of alkylsilyl groups inside the pores. Post-synthesis grafting of SBA-15 with SAMs worked not as well as CAMs: the surfaces prepared demonstrated lower water CAs and higher BET C constants, thereby indicating a small amount of accessible polar groups (Si-OH) related to packing constrains for SAMs supported on highly curved surfaces of mesopores. The co-condensation method produced substantially more disordered materials and less hydrophobic surfaces than any of the grafting methods. The surfaces of these materials showed low water CAs and high BET C constants (～100-200) thereby demonstrating a non-uniform surface coverage and presence of unmodified silica. It is concluded that CAMs chemistry is the most efficient approach in preparation of the functionalized OMS materials with uniform surfaces and pores.     

Globotriose- and oligo(ethylene glycol)-terminated self-assembled monolayers: surface forces, wetting, and surfactant adsorption

A set of oligo(ethylene glycol)-terminated and globotriose-terminated self-assembled monolayers (SAMs) has been prepared on gold substrates. Such model surfaces are well defined and have good stability due to the strong binding of thiols and disulfides to the gold substrate. They are thus very suitable for addressing questions related to effects of surface composition on wetting properties, surface interactions, and surfactant adsorption. These issues are addressed in this report. Accurate wetting tension measurements have been performed as a function of temperature using the Wilhelmy plate technique. The results show that the nonpolar character of oligo(ethylene glycol)-terminated SAMs increases slightly but significantly with temperature in the range 20-55 degrees C. On the other hand, globotriose-terminated SAMs are fully wetted by water at room temperature. Surface forces measurements have been performed and demonstrated that the interactions between oligo(ethylene glycol)-terminated SAMs are purely repulsive and similar to those determined between adsorbed surfactant layers with the same terminal headgroup. On the other hand, the interactions between globotriose-terminated SAMs include a short-range attractive force component that is strongly affected by the packing density in the layer. In some cases it is found that the attractive force component increases with contact time. Both these observations are rationalized by an orientation- and conformation-dependent interaction between globotriose headgroups, and it is suggested that hydrogen-bond formation, directly or via bridging water molecules, is the molecular origin of these effects.     

X-ray reflectivity and interfacial tension study of the structure and phase behavior of the interface between water and mixed surfactant solutions of CH3(CH2)19OH and CF3(CF2)7(CH2)2OH in hexane

The interface between water and mixed surfactant solutions of CH(3)(CH(2))(19)OH and CF(3)(CF(2))(7)(CH(2))(2)OH in hexane was studied with interfacial tension and X-ray reflectivity measurements. Measurements of the tension as a function of temperature for a range of total bulk surfactant concentrations and for three different values of the molal ratio of fluorinated to total surfactant concentration (0.25, 0.28, and 0.5) determined that the interface can be in three different monolayer phases. The interfacial excess entropy determined for these phases suggests that two of the phases are condensed single surfactant monolayers of CH(3)(CH(2))(19)OH and CF(3)(CF(2))(7)(CH(2))(2)OH. By studying four different compositions as a function of temperature, X-ray reflectivity was used to determine the structure of these monolayers in all three phases at the liquid-liquid interface. The X-ray reflectivity measurements were analyzed with a layer model to determine the electron density and thickness of the headgroup and tailgroup layers. The reflectivity demonstrates that phases 1 and 2 correspond to an interface fully covered by only one of the surfactants (liquid monolayer of CH(3)(CH(2))(19)OH in phase 1 and a solid condensed monolayer of CF(3)(CF(2))(7)(CH(2))(2)OH in phase 2). This was determined by analysis of the electron density profile as well as by direct comparison to reflectivity studies of the liquid-liquid interface in systems containing only one of the surfactants (plus hexane and water). The liquid monolayer of CH(3)(CH(2))(19)OH undergoes a transition to the solid monolayer of CF(3)(CF(2))(7)(CH(2))(2)OH with increasing temperature. Phase 3 and the transition regions between phases 1 and 2 consist of a mixed monolayer at the interface that contains domains of the two surfactants. In phase 3 the interface also contains gaseous regions that occupy progressively more of the interface as the temperature is increased. The reflectivity determined the coverage of the surfactant domains at the interface. A simple model is presented that predicts the basic features of the domain coverage as a function of temperature for the mixed surfactant system from the behavior of the single surfactant systems.     

Self-assembled monolayers of CH3COS- terminated surfactant-encapsulated polyoxometalate complexes

Self-assembled monolayers (SAMs) on gold surfaces based on three kinds of acetylthio-surfactant-encapsulated polyoxometalate clusters (thio-SECs) terminated with multiple CH(3)COS- groups, (NC(26)H(55)S(CO)CH(3))(6)H(2)[Co(H(2)O)CoW(11)O(39)], (NC(26)H(55)S(CO)CH(3))(13)H(3)[Co(4)(H(2)O)(2)(P(2)W(15)O(56))(2)], and (NC(26)H(55)S(CO)CH(3))(13)[Fe(4)(H(2)O)(2)(P(2)W(15)O(56))(2)]Br, have been prepared, which is representative of a general methodology to fabricate polyoxometalate-based SAMs. Thio-SECs self-assembled into monolayers on gold surfaces through the hydrolysis of CH(3)COS- groups and the subsequent formation of S-Au bonds, which was confirmed by grazing angle infrared spectroscopy, X-ray photoelectron spectroscopy, and ellipsometric and scanning tunneling microscopy (STM) measurements. Furthermore, the SAMs of the thio-SECs possess closely packed structures, and the local short-range order is clearly observed in the magnified STM image. We have also investigated the electrochemical behavior of SAMs of thio-SECs by cyclic voltammetry in detail, and the redox potential of the original polyoxometalates has been well retained. The electrochemical signals of the SAMs are very weak because of the small moiety of thio-SECs that are electrochemically accessible in the cyclic voltammetry experiments. The polyoxometalate-modified electrodes that we prepared are not only highly ordered in the local short range but also stable in electrochemical cycling because of the multiple S-Au bonds of thio-SECs on the gold substrates that aid in the construction of functional materials such as electrochemical and electrocatalytic devices.     

Self-assembled monolayers of semifluorinated alkaneselenolates on noble metal substrates

Self-assembled monolayers (SAMs) formed from semifluorinated dialkyldiselenol (CF(3)(CF(2))(5)(CH(2))(2)Se-)(2) (F6H2SeSeH2F6) on polycrystalline Au(111) and Ag(111) were characterized by high-resolution X-ray photoelectron spectroscopy, infrared reflection absorption spectroscopy, near edge X-ray absorption fine structure spectroscopy, scanning tunneling microscopy, and contact angle measurements. The Se-Se linkage of F6H2SeSeH2F6 was found to be cleaved upon the adsorption, followed by the formation of selenolate-metal bond. The resulting F6H2Se SAMs are well-ordered, densely packed, and contamination-free. The packing density of these films is governed by the bulky fluorocarbon part, which exhibits the expected helical conformation. A noncommensurate hexagonal arrangement of the F6H2Se molecules with an average nearest-neighbor spacing of about 5.8 +/- 0.2 A, close to the van der Waals diameter the fluorocarbon chain, was observed on Au(111). The orientation of the fluorocarbon chains in the F6H2Se SAMs does not depend on the substrate-the average tilt angle of these moieties was estimated to be about 21-22 degrees on both Au and Ag.     

Influence of nanobubbles on the adsorption of nanoparticles

A quartz crystal microbalance was used to study the influence of nanobubbles on the adsorption of polystyrene nanoparticles onto surfaces coated with gold, or coated with dodecanethiol or mercaptoundecanoic acid self-assembled monolayers (SAMs). Adsorption of the nanoparticles onto the surface causes the resonant frequency of the quartz crystal to decrease. We found that particles were adsorbed onto the gold-coated quartz crystal in air-rich water, but not in degassed water. This finding supports the long-standing hypothesis that nanobubbles play a key role in the long-range attractive force between hydrophobic surfaces in aqueous solutions. When the experiments were conducted using quartz crystals coated with a hydrophobic dodecanethiol SAM, the nanoparticles were adsorbed onto the surface even in degassed water due to the short-range hydrophobic interactions between the nanoparticles and the dodecanethiol molecules. In contrast, the nanoparticles were adsorbed to a lesser degree onto the hydrophilic mercaptoundecanoic acid-coated crystals due to electrostatic repulsive forces.     

Chemical Force Microscopy Study of Adhesion and Friction between Surfaces Functionalized with Self-Assembled Monolayers and Immersed in Solvents

Adhesive and frictional forces between surfaces modified with self-assembled monolayers (SAMs) and immersed in solvents were measured with chemical force microscopy as functions of surface functionality and solvent. Si/SiO2 substrates were modified with SAMs of alkylsiloxanes (SiCl3(CH2)n-X), and gold-coated AFM tips were modified with SAMs of alkylthiolates (HS-(CH2)n-X). SAMs of alkylsiloxanes terminated in a methyl or oxidized vinyl group; SAMs of alkanethiolates terminated in a methyl or carboxyl group. Adhesive and frictional forces were measured in hexadecane, ethanol, 1,2-propanediol, 1,3-propanediol, and water. The work of adhesion (W) was calculated with the Johnson-Kendall-Roberts theory of adhesive contact. The JKR values agreed well with values derived from the Fowkes-van Oss-Chaudhury-Good surface tension model and from contact angle results. Calculated values of W for all combinations of contacting surfaces and solvents spanned two orders of magnitude. W correlated with the surface tension of the solvent for hydrophobic/hydrophobic interactions; hydrophilic/hydrophilic and hydrophobic/hydrophilic interactions were more complex. Friction forces were fit to a modified form of Amonton's law. For any solvent, friction coefficients were largest for the hydrophilic/hydrophilic contacting surfaces. The friction coefficient for any contacting pair was largest in hexadecane. In polar solvents, friction coefficients scaled with solvent polarity only for hydrophobic/hydrophobic contacting pairs. Copyright 1999 Academic Press.     

4,4'-Bipyridazine: a new twist for the synthesis of coordination polymers

A new polydentate ligand 4,4'-bipyridazine (4,4'-bpdz) was prepared by employing inverse electron demand cycloaddition of 1,2,4,5-tetrazine. A unique combination of structural simplicity, ampolydentate character and efficient donor properties towards Cu(I), Cu(II) and Zn(II) provide wide new possibilities for the synthesis of coordination polymers incorporating the 4,4'-bpdz module either as a bi-, tri- or tetradentate connector between the metal ions. 1D coordination polymers Cu(2)(4,4'-bpdz)(CH(3)CO(2))(4) x 4H(2)O and Zn(4,4'-bpdz)(NO(3))(2), and interpenetrated (4,4)-nets in [Cu(4,4'-bpdz)(2)(H(2)O)(2)]S(2)O(6) were closely related to 4,4'-bipyridine compounds. 1D "ladder-like" polymer Cu(2)(4,4'-bpdz)(3)(CF(3)CO(2))(4) and the unprecedented 3D binodal net ({8(6)}{6(3);8(3)}) in [Cu(3)(4,4'-bpdz)(6)(H(2)O)(4)](BF(4))(6) x 6H(2)O were based upon a combination of linear and angular organic bridges. Complex [Cu(3)(OH)(2)(4,4'-bpdz)(3)(H(2)O)(2){CF(3)CO(2)}(2)](CF(3)CO(2))(2) x 2H(2)O has a "NbO-like" 3D topology incorporating discrete dihydroxotricopper(II) clusters linked by tri- and tetradentate ligands. The tetradentate function of the 4,4'-bpdz ligand was especially relevant for copper(I) complexes, which adopt layered Cu(2)X(2)(4,4'-bpdz) (X = Cl, Br) or 3D chiral framework (X = I) structures based upon infinite (CuX)(n) chains. The electron deficient character of the ligand was manifested by short anion-pi interactions (O-pi 3.02-3.20; Cl-pi 3.35 A), which may be involved as a factor for controlling the supramolecular structure.     

Formation mechanisms and properties of semifluorinated molecular gradients on silica surfaces

The goal of this study is to elucidate the formation of molecular gradients made of semifluorinated organosilanes (SFOs) on flat substrates by using a methodology developed by Chaudhury and Whitesides (Science 1992, 256, 1539). We use surface-sensitive combinatorial near-edge X-ray absorption fine structure (combi-NEXAFS) spectroscopy to measure the position-dependent concentration and orientation of SFO molecules in SFO molecular gradients on flat silica surfaces. Using the combi-NEXAFS data, we establish the correlation between the fraction of the F(CF(2))(8)(CH(2))(2)- species on the substrate and the average tilt angle of the -(CF(2))(8)F group in the SFO as a function of the deposition gas medium (air vs nitrogen) and the end group around the silicon atom (monofunctional vs trifunctional). In addition, we utilize the gradient geometry to comprehend the mechanism of formation of SFO self-assembled monolayers (SAMs). Specifically, we provide evidence that depending on the nature of the end group in the SFO and the vapor phase the SFO molecules add themselves into the existing SAMs either as individual molecules or as multimolecular complexes.     

Protein adsorption on oligo(ethylene glycol)-terminated alkanethiolate self-assembled monolayers: The molecular basis for nonfouling behavior

A study of protein resistance of oligo(ethylene glycol) (OEG), HS(CH2)11(OCH2CH2)nOH (n = 2, 4, and 6), self-assembled monolayers (SAMs) on Au(111) surfaces is presented here. Hydroxyl-terminated OEG-SAMs are chosen to avoid the hydrophobic effect observed with methyl-terminated OEG-SAMs, particularly at high packing densities. The structure of the OEG-SAM surfaces is controlled by adjusting the assembly solvent. These SAMs were characterized by X-ray photoelectron spectroscopy (XPS) and atomic force microscopy (AFM). Protein adsorption on these surfaces was investigated by surface plasmon resonance (SPR). OEG-SAMs assembled from mixed ethanol and water solutions show higher packing density on gold than those from pure ethanol solution. For EG2OH- and EG4OH-SAMs, proteins (i.e., fibrinogen and lysozyme) adsorb more on the densely packed SAMs prepared from mixed ethanol and water solutions, while EG6OH-SAMs generally resist protein adsorption regardless of the assembly solvent used.     

Fluorine-fluorine interactions in the solid state: an experimental and theoretical study

The solid state structures of three compounds that contain a perfluorinated chain, CF(3)(CF(2))(5)CH(2)CH(CH(3))CO(2)H, CF(3)(CF(2))(5)(CH(2))(4)(CF(2))(5)CF(3) and {CF(3)(CF(2))(5)CH(2)CH(2)}(3)P═O have been compared and a number of C-F···F-C and C-F···H-C interactions that are closer than the sum of the van der Waals radii have been identified. These interactions have been probed by a comprehensive computational chemistry investigation and the stabilizing energy between dimeric fragments was found to be 0.26-29.64 kcal/mol, depending on the type of interaction. An Atoms-in-Molecules (AIM) study has confirmed that specific C-F···F-C interactions are indeed present, and are not due simply to crystal packing. The weakly stabilizing nature of these interactions has been utilized in the physisorption of a selected number of compounds containing long chain perfluorinated ponytails onto a perfluorinated self-assembled monolayer, which has been characterized by IRRAS (Infrared Reflection Absorption Spectroscopy).     

Large cluster formation through multiple substitution with lanthanide cations (La, Ce, Nd, Sm, Eu, and Gd) of the polyoxoanion

Several new large polyoxotungstates have been synthesized by reaction of lanthanide cations with the well-known "As(4)W(40)" anion, [(B-alpha-AsO(3)W(9)O(30))(4)(WO(2))(4)](28-) (1). The heteropolyanions [(H(2)O)(11)Ln(III)(Ln(III)(2)OH)(B-alpha-AsO(3)W(9)O(30))(4)(WO(2))(4)](20)(-) (Ln = Ce, Nd, Sm, Gd) (2-4) (Ln(3)As(4)W(40)) and [M(m)()(H(2)O)(10)(Ln(III)(2)OH)(2)(B-alpha-AsO(3)W(9)O(30))(4)(WO(2))(4)]((18-m)(-)) (Ln = La, Ce, Gd and M = Ba, K, none) (5-7) (Ln(4)As(4)W(40)) have been isolated as alkali metal and ammonium salts, respectively, and characterized by single-crystal X-ray analysis, elemental analysis, and IR and (183)W-NMR spectroscopy. The X-ray analyses revealed interanionic W-O-Ln bonds between adjacent Ln(x)()As(4)W(40) units forming a "dimer" for x = 3 and chains for x = 4. Upon dissolving in water these bonds hydrolyze and the monomeric species form. The straightforward syntheses which require the use of concentrated NaCl solutions (1-4 M) and the addition of stoichiometric amounts of Ba(2+) or K(+) reemphasize the importance of the presence of appropriate countercations for the assembly of large polyoxometalate structures.     

Immunosensor interface based on physical and chemical immunoglobulin G adsorption onto mixed self-assembled monolayers

An immunosensor interface based on mixed hydrophobic self-assembled monolayers (SAMs) of methyl and carboxylic acid terminated thiols with covalently attached human Immunoglobulin G (hIgG), is investigated. The densely packed and organised SAMs were characterised by contact angle measurements and cyclic voltammetry. The effect of the non-ionic surfactant, Tween 20, in preventing nonspecific adsorption is addressed by ellipsometry during physical and covalent hIgG immobilization on pure and mixed SAMs, respectively. It is clearly demonstrated that nonspecific adsorption due to hydrophobic interactions of hIgG on methyl ended groups is totally inhibited, whereas electrostatic/hydrogen bonding interactions with the exposed carboxylic groups prevail in the presence of surfactant. Results of ellipsometry and Atomic Force Microscopy, reveal that the surface concentration of covalently immobilized hIgG is determined by the ratio of COOH / CH(3)-terminated thiols in SAM forming solution. Moreover, the ellipsometric data demonstrates that the ratio of bound anti-hIgG / hIgG depends on the density of hIgG on the surface and that the highest ratio is close to three. We also report the selectivity and high sensitivity achieved by chronoamperometry in the detection of adsorbed hIgG and the reaction with its antibody.