微放电等离子体多负辉区结构融合过程数值模拟研究

高气压下的微型电热推进器(MPT)中的放电等离子体存在多负辉区结构,其负辉区有融合趋势。对矩形微放电等离子体推进器(RMPT)的负辉区融合过程进行了二维模拟分析,在方法上采用了非平衡态的自洽流体模型,并考虑了离子电流加热和三体碰撞过程。结果显示：矩形微放电等离子体推进器(RMPT)在低电流条件下存在两个稳定的负辉区,当超过某一电流阈值条件后,两个负辉区会在腔体中心重合。分析了这一过程的成因,认为其融合过程本质上是空心阴极的导通过程,其融合与否与鞘层电压有关。     

微放电等离子体多负辉区结构融合过程数值模拟研究

高气压下的微型电热推进器(MPT)中的放电等离子体存在多负辉区结构,其负辉区有融合趋势。对矩形微放电等离子体推进器(RMPT)的负辉区融合过程进行了二维模拟分析,在方法上采用了非平衡态的自洽流体模型,并考虑了离子电流加热和三体碰撞过程。结果显示:矩形微放电等离子体推进器(RMPT)在低电流条件下存在两个稳定的负辉区,当超过某一电流阈值条件后,两个负辉区会在腔体中心重合。分析了这一过程的成因,认为其融合过程本质上是空心阴极的导通过程,其融合与否与鞘层电压有关。     

赝火花开关辉光放电腔的粒子模拟与实验研究

给出了赝火花开关所需辉光放电腔的具体要求,对赝火开关辉光放电腔进行了优化设计,并对优化后的放电腔进行了粒子模拟和实验研究。粒子模拟结果表明：此放电腔为辉光放电腔,辉光放电建立时间约18.5 ns;辉光放电时,此放电腔阴极位降占整个电位降的主要部分,且阴极位降区净离子密度为一常数。实验结果显示：此放电腔为辉光放电腔,其工作在Paschen曲线最低点左侧,放电电压随气压的升高而降低;当辉光放电电流为0.14～3.60 mA时,放电模式为正常辉光放电。     

Electron impact ionization and excitation rate coefficients in the negative glow region of a glow discharge

Some easy to use reasonable approximations for electron impact rate coefficients have been considered. The most important rate coefficients for electron collisions in noble gases are electron-neutral ionization and electron impact excitation. Electron-neutral ionization besides electron impact excitation of some states of the argon and helium atom in direct current (dc) glow discharge plasma has been calculated. The plasma parameters of electron are significant factors for computing the rate coefficients. We present first results of probe diagnostic that includes the double probe measurements of the plasma parameters, namely, electron temperature (T_e) and electron density (n_e). Electron properties obtained from the double probe characteristic curves including T_e and n_e as well as the calculated rate coefficients (ionization and excitation) were studied as a function of the axial distance from the cathode while the discharge operating parameters of voltage and pressure were varied. Two regions of the glow discharge were investigated: cathode fall region and negative glow. Particular emphasis was placed on the negative glow region.     

Non-local model of hollow cathode and glow discharge

A general form of the non-local equation for an ionization source in glow discharge and hollow cathode 3D-simulation is formulated. It is a fundamental equation in hollow cathode theory, which allows formulation of a complete set of field equations for a self-consistent problem in a stationary glow discharge and hollow cathode. It enables us to describe the region of negative glow and the hollow cathode effect and compare calculation results of electrical dependencies (pressure-voltage) with experimental data, – under conditions of gradual appearance of the hollow cathode effect.     

Theory of a normal high-pressure glow discharge

In the present work, a theoretical model considering the processes of generation and losses of charged particles in the cathode region of a glow discharge in the drift approximation for ion and electron motion is developed. Exact analytical solutions, which can be used to calculate the current-voltage characteristics of the glow discharge in an arbitrary gas with the known Townsend ionization coefficient, are derived. The calculated parameters of the normal glow discharge (the current density, discharge burning voltage, and width of the space charge region) for different gases are in good agreement with the available experimental data. __________ Translated from Izvestiya Vysshikh Uchebnykh Zavedenii, Fizika, No. 2, pp. 71–77, February, 2006.     

赝火花开关辉光放电腔的粒子模拟与实验研究

 给出了赝火花开关所需辉光放电腔的具体要求,对赝火开关辉光放电腔进行了优化设计,并对优化后的放电腔进行了粒子模拟和实验研究。粒子模拟结果表明：此放电腔为辉光放电腔,辉光放电建立时间约18.5 ns;辉光放电时,此放电腔阴极位降占整个电位降的主要部分,且阴极位降区净离子密度为一常数。实验结果显示：此放电腔为辉光放电腔,其工作在Paschen曲线最低点左侧,放电电压随气压的升高而降低;当辉光放电电流为0.14～3.60 mA时,放电模式为正常辉光放电。     

Role of nonlocal ionization in formation of the short glow discharge

An analytical model for estimating basic characteristics of short (without a positive column) glow discharges is suggested that allows for electron generation both in the cathode sheath and by nonlocal ionization in the plasma negative glow. The model is based on a previously developed approach according to which the discharge gap is divided into space-charge layers and a quasi-neutral plasma. The plasma region includes part of the negative glow, Faraday dark space, and positive column (if it exists). Simple expressions for basic characteristics of the glow discharge (I–V characteristic, cathode sheath thickness, position of the point of electric field reversal, etc.) are derived, and plasma concentration distributions are presented. The results obtained in terms of our model are in good agreement with experimental data, while local approximations based on the classical Engel-Steenbeck model diverge considerably from the experiment.     

Numerical studies of atmospheric pressure glow discharge controlled by a dielectric barrier between two coaxial electrodes

The glow discharge in pure helium at atmospheric pressure, controlled by a dielectric barrier between coaxial electrodes, is investigated based on a one-dimensional self-consistent fluid model. By solving the continuity equations for electrons, ions, and excited atoms, with the current conservation equation and the electric field profile, the time evolution of the discharge current, gas voltage and the surface density of charged particles on the dielectric barrier are calculated. The simulation results show that the peak values of the discharge current, gas voltage and electric field in the first half period are asymmetric to the second half. When the current reaches its positive or negative maximum, the electric field profile, and the electron and ion densities represent similar properties to the typical glow discharge at low pressures. Obviously there exist a cathode fall, a negative glow region, and a positive column. Effects of the barrier position in between the two coaxial electrodes and the discharge gap width on discharge current characteristics are also analysed. The result indicates that, in the case when the dielectric covering the outer electrode only, the gas is punctured earlier during the former half period and later during the latter half period than other cases, also the current peak value is higher, and the difference of pulse width between the two half periods is more obvious. On reducing the gap width, the multiple current pulse discharge happens.     

介质阻挡均匀大气压辉光放电数值模拟研究

通过数值求解一维电子、离子连续性方程和动量方程，以及电流连续性方程，计算了氦气介 质阻挡大气压辉光放电电子、离子密度和电场在放电空间的时空分布，以及放电电流密度和 绝缘介质板充电电荷密度随时间的变化. 分析讨论所加电压频率、幅值及介质板性质等对均 匀大气压辉光放电性质的影响. 当外加电压频率足够高时，大量离子被俘获在放电空间，空 间电荷场又引起足够多的电子滞留在放电空间. 这些种子电子使得在大气压下发生汤森放电 ，放电空间结构类似于低气压辉光放电，即存在明显的阴极位降区、负辉区、法拉第暗区和 等离子体正柱 关键词： 大气压辉光放电 介质阻挡 数值模拟 等离子体     

Simulation of radio-frequency atmospheric pressure glow discharge in γ mode

The existence of two diffe1：ent discharge modes has been verified in an rf （radio-frequency） atmospheric pressure glow discharge （APGD） by Shi [J. Appl. Phys. 97, 023306 （2005）]. In the first mode, referred to as a mode, the discharge current density is relatively low and the bulk plasma electrons acquire the energy due to the sheath expansion. In the second mode, termed γ mode, the discharge current density is relatively high, the secondary electrons emitted by cathodc under ion bombardment in the cathode sheath region play an important role in sustaining the discharge. In this paper, a one-dimensional self-consistent fluid model for rf APGDs is used to simulate the discharge mechanisms in the mode in helium discharge between two parallel metallic planar electrodes. The results show that as the applied voltage increases, the discharge current becomes greater and the plasma density correspondingly increases, consequentially the discharge transits from the a mode into the γ mode. The high collisionality of the APGD plasma results in significant drop of discharge potential across the sheath region, and the electron Joule heating and the electron collisional energy loss reach their maxima in the region. The validity of the simulation is checked with the available experimental and numerical data.     

The effect of ion emission on the characteristics of a glow discharge with a hollow cathode

The effect of extraction of the ion current on the conditions for sustaining a low-pressure glow discharge with a hollow cathode, which is a topical problem for developing ion sources, is studied. It is shown that there exists a certain optimal level of the ion emission at which the energy efficiency reaches its maximum.     

大气压氩气介质阻挡辉光放电的一维仿真研究

为了研究氩气(Ar)中介质阻挡大气压辉光放电(APGD)的放电机理, 通过建立一个一维的多粒子自洽耦合流体模型, 采用有限元方法进行数值计算, 得到了气体间隙压降、介质表面电荷密度、放电电流密度随时间的周期变化波形, 以及电子、离子、亚稳态粒子密度和空间电场强度的时空分布. 仿真计算结果表明：介质表面积聚的电荷对于放电的过程的起始及熄灭具有重要作用;当增大外施电压时, 放电击穿时刻提前, 放电电流密度和介质表面电荷密度峰值增大, 表明放电过程更加剧烈;随着阻挡介质相对介电常数的增大, 放电电流密度也随之增大. 各粒子密度及电场的时空分布表明放电过程在外施电压半个周期中只有一次放电, 且存在明显的阴极位降区、负辉区、等离子体正柱区等辉光放电的典型区域, 为大气压辉光放电(APGD).     

A model of the cathode spot glow discharge for a cathode withinclusions of low work function material

A model that describes the self-maintained glow discharge for a composite cathode in which cathode spots are formed on low work function material inclusions is presented. Based on this model, expressions are obtained for the radius of the spot, the cathode voltage, and the spot current as functions of Pd (where P is the gas pressure and d is the thickness of the cathode layer), the parameters of the inclusions, and the basic material matrix are obtained. Numerical results for the case of a glow discharge in 75 torr neon gas with a copper cathode matrix and inclusions of LaB₆ are presented. The average radii of inclusions were 0.05 and 0.015 mm. Conditions under which the glow discharge migrates from the inclusions and begins to spread onto the surface of the basic matrix are obtained. The transition of the glow discharge into a contracted state, depending on the structure of the composite material, is also considered     

Ferrite stabilization induced by molybdenum enrichment in the surface of unalloyed iron sintered in an abnormal glow discharge

Unalloyed iron was sintered using an abnormal glow discharge with confined anode-cathode configuration. This electrode arrangement allows heating the component as well as enriching the surface with atoms from the cathode. In order to sinter unalloyed iron with molybdenum enrichment, the samples were placed on a holder acting as the discharge anode, inside a cylindrical cathode of Mo. The cathode was heated by the bombardment of ions and fast neutrals accelerated in the cathode sheath and as a consequence of the confined geometry the sample was efficiently heated by thermal radiation. On heating, the ion and neutral species bombardment produces sputtering of atoms of the cathode, which by diffusion in the gas phase deposit on the sample surface. During sintering the deposited atoms diffuse into the sample, resulting in a layer enriched with elements sputtered out from the cathode. Mo enrichment was observed on the sample surface (more than 4 wt%), which resulted in stabilization of the Fe α-phase at the treatment temperature. Under these conditions, as the diffusion coefficient in the Fe α-phase is about 10² times higher than in the γ-phase, the sintering of this enriched phase is activated.     

High current density spotless vacuum arc as a glow discharge

Vacuum discharge burning between a broad cathode and a point anode made of Mo, Cu, and Cd has been studied. This discharge operates in anode vapors and shows major arc characteristics, although no craters were examined on the cathode. The secondary electron emission is involved to explain current transport within the cathode region. This discharge is interpreted as a high density low voltage glow discharge. Having discussed the present and previous findings, the conclusion has been drawn that the secondary electron emission and “hump of potential” are dominant in the vacuum arc cathode spot     

Analysis of new electrical signals in respect to quantification of radio frequency glow discharge emission spectrometry

Radio frequency glow discharge optical emission spectroscopy (RF-GD-OES) is routinely used for the chemical analysis of solid samples. For quantification two independent electrical signals of the discharge are required. These are provided in real time by the glow discharge source with integrated voltage and current sensors. The available time-dependent voltage and current must be reduced. For this purpose a plasma equivalent circuit is used. It is shown that the cathode voltage and active cathode current describe the sputtering and excitation well. Measuring standard reference materials at constant cathode voltage and cathode current results in linear calibration curves.     

Structure of the glow of a nanosecond diffuse discharge in a strongly nonuniform electric field

The structure of the glow of a diffuse discharge in air under atmospheric pressure is studied in detail in the “rod (cathode)-plane” geometry for an electrode gap of 10 cm and a cathode tip radius from 3 cm to 2.4 μm. The amplitude of voltage across the gap was ～ 220 kV for voltage growth rate of ～10¹³ V/s and a pulse duration of 180 ns. It is found that the shape of the discharge glow strongly depends on the radius of the cathode tip. For large values of the radius, the multichannel form of the glow prevails, which is statistically transformed into a volume glow as the radius decreases from 5 mm to 60 μm. This transition is accompanied by a decrease in the amplitude of the discharge current from 440 to 140 A on the average. For ultrasmall radii of the cathode (2.4–7.7 μm), the multichannel form of the glow prevails again and the amplitude of the discharge current increases up to ～300 A.     

磁控溅射辉光放电特性的模拟研究

采用二维、自洽的PIC/MCC (particle-in-cell with Monte Carlo collision) 方法,模拟了磁控溅射辉光放电过程, 重点讨论了工作参数对放电模式和放电电流的影响. 模拟结果表明, 当工作气压由小到大或空间磁场从强到弱变化时, 放电模式会从阴极空间电荷主导的放电模式过渡到阳极空间电荷主导 的放电模式.在过渡状态,对应的工作气压与磁通密度分别为0.67 Pa和0.05 T; 随着工作气压的增大,放电电流先增大后趋向平衡,当工作气压超过2.5 Pa时,电流开始随工作气压的增大而减小; 而阴极电压增大时,放电电流近似线性增加.     

Theorie der Strom-Spannungs-Kennlinien von Quecksilberdampf-Glimmentladungen im Bereich des Nahdurchschlages

Based on the elementary processes in the cathode fall of a glow discharge below the Paschen minimum the current-voltage-characteristic is calculated, at first under extensive simplifications and then exactly. It shows that the negative glow is of an essential importance. The influence of the negative glow on the cathode fall is examined and it is taken into consideration for the calculation of the current voltage-characteristic. Further it is considered that the α-ionization coefficient in the cathode fall is not constant, but depends at a high degree on the shape of the potential.