Quantitative Determination of Hyponitrite and Hyponitrate by Ion Chromatography

A simple, sensitive and reliable method for the rapid determination of hyponitrite and hyponitrate (Angeli’s salt) in alkaline media, is presented where both species are relatively stable. The method is based on the separation of the two anions by an anion exchange column and thereafter UV spectrophotometric detection at 248 nm. The calibration curves were linear over the concentration range of 0.4–100 mg L^?1, whereas the detection limit was found to be 50 μg L^?1 for hyponitrite and 100 μg L^?1 for hyponitrate. Under these conditions, the determination of nitrate and nitrite is also possible.     

A Simple Method for Determination of Homologue Imidazolium Cations in Ionic Liquids Using IC with Direct Conductivity Detection

An investigation was carried out into the fast determination of five homologue imidazolium cations in ionic liquids by ion chromatography using a cation-exchange column and direct conductivity detection. Ethylenediamine, complex organic acid (citric acid, oxalic acid and tartaric acid) and organic modifiers (acetonitrile) were used as mobile phase. The influences of the eluent types, eluent concentration, eluent pH and column temperature on separation of the cations were discussed. Simultaneous separation and determination of the five homologue imidazolium cations in ionic liquids were achieved under an optimum condition. The optimized mobile phase was consisted of 0.25 mmol L^?1 ethylenediamine + 0.5 mmol L^?1 citric acid + 3% acetonitrile (v/v) (pH 4.1), set at a flow rate of 1.0 mL min^?1. The column temperature was 40 °C and detection limits were obtained in the range of 1.1–45.6 mg L^?1. The relative standard deviations of the chromatographic peak areas for the cations were <3.0% (n = 5). This method was successfully applied to separate imidazolium cations in ionic liquids produced by organic synthesis. The recoveries of spiked components were 92.5–101.9%.     

Rapid Determination of Trifluoromethanesulfonate and p-Toluenesulfonate by Ion-Pair Chromatography Using a Reversed-Phase Silica-Based Monolithic Column: Application to the Analysis of Ionic Liquids

A method of ion-pair chromatography was developed on a reversed-phase silica-based monolithic column for the fast and simultaneous determination of trifluoromethanesulfonate (CF₃SO₃ ⁻) and p-toluenesulfonate (C₇H₇SO₃ ⁻). The analysis was performed using a mobile phase of tetrabutylammonium hydroxide + citric acid + acetonitrile on the Chromolith Speed ROD RP-18e column with direct conductivity detection. The effects of the eluent, column temperature and flow rate on the retention of the anions were investigated. The experimental phenomenon was discussed according to hydrophobic interaction and ion-exchange mechanism in the separation. The optimized chromatographic conditions were selected. The optimized eluent for the separation consisted of 0.2 mmol L⁻¹ tetrabutylammonium hydroxide + 0.10 mmol L⁻¹ citric acid + 9% acetonitrile (pH 5.5). The flow rate was set at 6.0 mL min⁻¹. The column temperature was 25 °C. Under the optimal conditions, the better separation of CF₃SO₃ ⁻ and C₇H₇SO₃ ⁻ was achieved without any interference by other anions (Cl⁻, Br⁻, I⁻, NO₃ ⁻, SO₄ ²⁻, ClO₃ ⁻, BF₄ ⁻ and PF₆ ⁻). The detection limit (S/N = 3) was 0.28 and 0.71 mg L⁻¹ for CF₃SO₃ ⁻ and C₇H₇SO₃ ⁻, respectively. The method has been applied to the determination of CF₃SO₃ ⁻ and C₇H₇SO₃ ⁻ in ionic liquids. The spiked recoveries of CF₃SO₃ ⁻ and C₇H₇SO₃ ⁻ were 101.1 and 100.2%, respectively.

     

CE, with Hydroxypropyl-β-Cyclodextrin as Chiral Selector, for Separation and Determination of the Enantiomers of Amlodipine in the Serum of Hypertension Patients

A capillary electrophoretic method for separation of the enantiomers of amlodipine in the serum of hypertension patients has been established and validated. The two enantiomers were separated in a fused-silica capillary with phosphate running buffer (75 mmol L^?1, pH 2.5) containing 15 mmol L^?1 hydroxypropyl-β-cyclodextrin (HP-β-CD). The effects on the separation of buffer pH and concentration, separation potential, and concentration of HP-β-CD were investigated. The range of quantitation for both enantiomers was 2.0–16.0 μg mL^?1. Intra-day and inter-day relative standard deviation (RSD; n = 5) was <10%. The limits of detection (LOD) and quantification (LOQ) of the amlodipine enantiomers, at 214 nm, were approximately 0.5 and 0.7 μg mL^?1, respectively (S/N = 3 and 10, respectively; 5-s injection). Recovery was always >85%. Results from enantiomer separation and quantification showed that concentrations of the enantiomers of amlodipine in serum from an elderly patient were higher than in serum from a young patient administered the same dose. The method was useful for determining the concentration of the enantiomers of amlodipine in hypertension patient serum and for monitoring the transition behavior of the enantiomers in humans. The method proved suitable for application to the separation of the enantiomers of amlodipine and analysis of clinical samples.     

Use of Capillary Zone Electrophoresis and Micellar Electrokinetic Chromatography for Separations of Anthraquinone Derivatives

The behavior of seven hydroxy anthraquinone derivatives was studied by capillary zone electrophoresis and micellar electrokinetic chromatography. The effects of buffer pH (6.5–10.8) and sodium dodecyl sulfate concentration (10–20 mmol L^?1) on the effective mobilities of the analytes and their separation were tested. A comparison of the two optimized separation systems showed that micellar electrokinetic chromatography was superior as it permits separation of all the seven analytes within 15 min, using 15 mmol L^?1 sodium dodecyl sulfate in 10 mmol L^?1 tetraborate buffer, pH 8.5, at a voltage of 20 kV. The calibration curves were linear in the concentration range from 5.0 · 10^?7 to 5.0 · 10^?4 mol L^?1 for most of the analytes, at a detection wavelength of 254 nm. LOD and LOQ values of the analytes were in the ranges of 2.10 · 10^?7–1.28 · 10^?6 mol L^?1and 6.99 · 10^?7–4.25 · 10^?6 mol L^?1, respectively. The proposed separation conditions were applied to determination of 1,2-dihydroxy anthraquinone (alizarin) and 1,2,4-trihydroxy anthraquinone (purpurin) in Rubia tinctorum aglycone and of the recently described 1-acetyl-2,4,5,7-tetrahydroxy-9,10-anthraquinone and 1-acetyl-2,4,5,7,8-pentahydroxy-9,10-anthraquinone in the mycelium of fungi Geosmithia lavendula.     

GC–MS Method Development for the Analyses of Thiophenes from Solvent Extracts of Tagetes patula L

A method for isotachophoretic determination of potassium and ammonium cations in fertilizers and silage was developed. A capillary of 0.4 mm i.d. and 100 mm effective length made of fluorinated ethylene–propylene copolymer was filled with an electrolyte system consisting of 10 mmol L⁻¹ RbOH + 0.1% (w/v) hydroxyethylcellulose, adjusted to pH 9.0 with l-histidine (leading electrolyte) and 10 mmol L⁻¹ lithium citrate (terminating electrolyte). Using contactless conductivity detection, the calibration curves in the tested concentration range up to 0.5 mmol L⁻¹ were linear for both cations. The concentration detection limits for potassium and ammonium were 2.9 and 2.7 μmol L⁻¹, respectively. RSD values of step lengths (n = 6) were 1.3% for potassium and 1.5% for ammonium. The separation time was about 20 min. Similar results were obtained with cesium cation used as the leading ion, however, in the system with rubidium better resolution of other cations present in tested matrices was reached. The elaborated method is simple to perform, sufficiently sensitive and accurate and can be recommended as an alternative procedure to the methods used so far for the determination of potassium and ammonium.

     

Sequential Determination of Inorganic Cations and Anions in Cerebrospinal Fluid by Microchip Electrophoresis

Analysis of inorganic ions in cerebrospinal fluid (CSF) is used mainly in the diagnostics of central nervous system diseases, such as Alzheimer’s disease or multiple sclerosis. A new analytical method for fast determination of inorganic cations (ammonium, calcium, magnesium, sodium and potassium) and anions (chloride, sulfate, nitrite and nitrate) in CSF on an electrophoretic microchip was developed in this context. Zone electrophoresis (ZE) separations were performed on the microchip with coupled channels (CC) and contact conductivity detection. Two different propionate background electrolytes were used for the sequential determination of cations at pH 3.1 and anions at pH 4.3. ZE was used for the determination of cationic constituents while ZE–ZE approach was employed for the determination of chloride in the first separation channel on the CC microchip and other anionic micro-constituents in the second channel. LOD values were in the range of 0.003–0.012 mg L^?1 and 0.019–0.047 mg L^?1 for cations and anions, respectively. Repeatability of migration time was up to 1.2 % for both cations and anions. Repeatability of peak area ranged from 0.3 to 5.6 % for cations and from 0.6 to 6.0 % for anions. Recovery of both cations and anions was in the range 90–106 %. CSF samples were only diluted appropriately without other sample pretreatment prior to analysis. Developed sequential method is suitable for fast determination of the studied cations and anions in CSF with total analysis time <15 min.     

Simultaneous LC–UV–MS–MS Analysis of Nine Pivotal Metabolites in Human Serum: Application to Studies of Impaired Glucose Tolerance

A rapid, sensitive, and selective LC–UV–MS–MS method for simultaneous quantification of uric acid, creatinine, xanthine, creatine, hypoxanthine, adenosine, inosine, thymidine, and uridine in serum from patients with impaired glucose tolerance (IGT) has been developed and validated. After precipitation of protein in the serum with methanol samples were evaporated with a stream of nitrogen then reconstituted with aqueous ammonia (0.002 mol L^?1). Chromatographic separation was performed on a C₁₈ column with methanol–buffer (8 mmol L^?1 ammonium acetate adjusted to pH 6.1 with glacial acetic acid) as mobile phase at a flow rate of 0.8 mL min^?1. UV and MS–MS detection were used to quantify the metabolites on the basis of different concentrations and detector response. Linearity was excellent, with r ² no <0.998. Recovery, and intra-day and inter-day relative standard deviation (RSD) were >85, <10, and <10%, respectively. This reliable bioanalytical method enables evaluation of the levels of purines and pyrimidines in serum for IGT studies and diagnosis.     

Sequential Determination of Inorganic Cations and Anions in Cerebrospinal Fluid by Microchip Electrophoresis

Analysis of inorganic ions in cerebrospinal fluid (CSF) is used mainly in the diagnostics of central nervous system diseases, such as Alzheimer’s disease or multiple sclerosis. A new analytical method for fast determination of inorganic cations (ammonium, calcium, magnesium, sodium and potassium) and anions (chloride, sulfate, nitrite and nitrate) in CSF on an electrophoretic microchip was developed in this context. Zone electrophoresis (ZE) separations were performed on the microchip with coupled channels (CC) and contact conductivity detection. Two different propionate background electrolytes were used for the sequential determination of cations at pH 3.1 and anions at pH 4.3. ZE was used for the determination of cationic constituents while ZE–ZE approach was employed for the determination of chloride in the first separation channel on the CC microchip and other anionic micro-constituents in the second channel. LOD values were in the range of 0.003–0.012 mg L⁻¹ and 0.019–0.047 mg L⁻¹ for cations and anions, respectively. Repeatability of migration time was up to 1.2 % for both cations and anions. Repeatability of peak area ranged from 0.3 to 5.6 % for cations and from 0.6 to 6.0 % for anions. Recovery of both cations and anions was in the range 90–106 %. CSF samples were only diluted appropriately without other sample pretreatment prior to analysis. Developed sequential method is suitable for fast determination of the studied cations and anions in CSF with total analysis time <15 min.

     

Electroanalytical Characteristics of Lercanidipine and its Voltammetric Determination in Pharmaceuticals and Human Serum on Boron-Doped Diamond Electrode

The electrooxidative behavior and determination of lercanidipine (LRC) were investigated in aqueous acetonitrile medium at a boron-doped diamond electrode using voltammetric techniques. The LRC in selected supporting electrolyte presents a well-defined anodic response at 0.944 V, studied by the proposed method. The linear response was obtained in the ranges of 4 × 10^?6 to 2 × 10^?4 mmol L^?1 range in 0.5 mmol L^?1 sulfuric acid supporting electrolyte and 1 × 10^?5 to 8 × 10^?5 mmol L^?1 range in spiked serum sample for square wave voltammetric technique. No electroactive interferences from the excipients and endogenous substances were found in the pharmaceutical dosage form and in the biological sample, respectively.     

Determination of nitrite in environmental waters by flow injection catalytic spectrophotometry

ABSTRACT

The flow injection catalytic spectrophotometry is proposed for the determination of nitrite based on the catalytic effect on the redox reaction between methylene blue and potassium bromate in acidic medium. The reaction is monitored spectrophotometrically by measuring the decrease in the absorbance of methylene blue at the maximum absorption wavelength of 664 nm. The method is characterised by low solvent consumption and easy automatic continuous analysis. It has higher sensitivity and lower detection limit. Experimental analysis conditions of the flow injection-catalytic photometry are optimised, and the best analysis conditions are: the concentration of the potassium bromate is 0.068 mol L^?1; the concentration of the phosphoric acid in oxidation liquid is 0.045 mol L^?1; the concentration of the methylene blue in colour-substrate solution is 2.4 mg L^?1, the volume of sample ring is 200 μL; the reaction coil is around 7 m in length; the inject time is 50 s and analysis time is 70 s. Under the optimal conditions, the linear range is from 10 to 500 μg L^?1 and the detection limit is 1 μg L^?1. The nitrate standard solution is continuously determined with a mass concentration of 300 μg L^?1. The RSD is determined to be 1.41% (n = 10). The nitrite in water samples, which were from the Half Acre pond, the Ink River and the Small West lake in a campus, was determined respectively by this method. A satisfactory standard addition recovery of 96.7%–103.9% was obtained.     

Enhanced chromatographic separation of cobalt and uranyl ions using tin (IV) antimonate column from aqueous solution

The effect of electric field on tin (IV) antimonate column bed to separate cobalt and uranium was investigated. Separation was carried out from nitrate solution and ionic strength of 0.6. Variation of applied potential, time and pH were investigated. Ion mobilities at pH 1 are calculated and given to be 5.5 × 10^?4 and 2.73 × 10^?4 cm² V^?1 s^?1 for cobalt and uranyl ion respectively. Number of theoretical plate heights were calculated from the breakthrough curve and given to be 354 and 210 for cobalt and uranyl ions, respectively. Diffusion coefficient were calculated according to Nernst equation and found to be of 7.6 × 10^?6 and 3.5 × 10^?6 cm² s^?1 for cobalt and uranyl ions, respectively. Also, breakthrough capacities were calculated and found to be 0.7 mmol g^?1 for cobalt ion and 0.4 mmol g^?1 for uranyl ion, respectively.     

Use of Surfactant as Mobile Phase Additive in LC for Simultaneous Determination of Metal-Pyrrolidine Dithiocarbamate Chelates

Reversed phase liquid chromatography using UV detection was developed for the simultaneous analysis of Hg(II), Pb(II), Cd(II), Ni(II), Fe(III) and V(V) ions after their complexation with pyrrolidine-dithiocarbamate (PDC). Optimum chromatographic conditions were a μ-Bondapak C₁₈ column and an isocratic mobile phase consisting of 40 mmol L^?1 SDS, 34 mmol L^?1 TBABr and 68% acetonitrile in 10 mmol L^?1 phosphate buffer pH 3.5. The separation of six PDC complexes was achieved within 8 min. Analytical performances and method validation were investigated. The detection limits ranged from 0.16 μg L^?1(Fe(III)) to 5.40 μg L^?1(Pb(II)). Recoveries obtained for all the studied samples including tap water, whole blood and vegetables were 72–98%. The results obtained from the proposed method were not significantly different compared to those obtained from atomic absorption spectrometry (P = 0.05).     

Chemometric approach to the optimisation of LC-FL and GC-MS methods for the determination of nitrite and nitrate in some biological,food and environmental samples

Gas chromatography–mass spectrometry (GC-MS) method and a liquid chromatography–fluorescence (LC-FL) detection method using experimental design and optimisation approach were improved for the quantitative determination of nitrite and nitrate in biological, food and environmental samples. The obtained recoveries of nitrite and nitrate ions from samples based on both GC-MS and LC-FL results ranged from 98.5% to 98.9% for nitrite and 97.9% to 98.4% for nitrate. The precision of these methods, as indicated by the relative standard deviations (RSDs), was within the range from 2.4% to 3.6% for nitrite and 2.5% to 3.8% for nitrate, respectively. The limits of detection of nitrite and nitrate ions from samples based on GC-MS and LC-FL results ranged from 0.01 to 0.14 ng L^?1 for nitrite and 0.02 to 0.71 ng L^?1 for nitrate, respectively. The optimised isolation procedure by central composite design was successfully applied to real samples. The results revealed that the proposed procedure combined with GC-MS and LC-FL techniques is more sensitive, reliable and selective compared to the other methods available for the precise determination of trace levels of nitrite and nitrate in biological, food and environmental samples.     

Multivariate Optimization and Validation of a CZE Method for the Analysis of Pridinol Mesylate and Meloxicam in Tablets

A capillary zone electrophoresis method for the simultaneous determination of pridinol mesylate (PRI) and meloxicam (MEL) employing epinastine hydrochloride and piroxicam as internal standards, was developed and optimized employing experimental design and response surface methodologies. The separation was optimally achieved in less than 2 min at 30 kV in an uncoated fused-silica capillary (41.4 cm × 75 ??m I.D.), employing an 18 mmol L^?1 sodium phosphate buffer solution (pH 5.90) at 25 °C. Samples were injected in hydrodynamic mode (50 mbar, 5 s) and the analytes were spectrophotometrically detected at 200 nm. Method robustness was demonstrated by ANOVA of determinations performed under conditions slightly different from the optimum. The method was validated regarding separation selectivity (peak purity factors > 0.99), linearity and range (PRI = 17.6?C31.4 mg L^?1; MEL = 66.5?C122.5 mg L^?1), accuracy (PRI = 100.2?C101.9%; MEL = 98.9?C100.7%) and precision. The RSD values obtained were ??1.3% for injection repeatability and ??1.9% for intra-day precision. The limits of detection (1.0 and 0.9 mg L^?1) and quantification (3.3 and 16.5 mg L^?1) of PRI and MEL, respectively, were also determined. The method was successfully applied to the determination of both drugs in three brands of tablet formulations. No statistically significant differences were observed when these results were compared with those of a RP-HPLC method.     

Effect of surfactants on the performance of hollow fiber renewal liquid membrane (HFRLM): a case study of uranium transfer

In this study the application of various surfactant agents on the performance of HFRLM for uranium transfer was investigated. Using Taguchi experimental design in recycling mode of HFRLM, maximum uranium recovery of 63.17% was obtained at 0.15 mol L^?1 H₂SO₄, 0.0125 mol L^?1 Alamine 336 and 0.25 mol L^?1 NH₄Cl in the donor, liquid membrane and acceptor phase, respectively. Also, the continuous mode experiments were conducted and HFRLM stability was compared with HFSLM. The uranium transfer would be improved by adding 0.05 mmol L^?1 of SDS, CTAB and LAE-7 to the donor phase and 10 mmol L^?1 of CTAB and LAE-7 to the acceptor phase.     

Determination of Copper in Human Urine by RP-LC After Pre-column Derivatization with Neocuproine and Use of Monolithic Column

A selective sensitive RP-LC–UV/VIS method with pre-column derivatization was developed for the determination of copper in human urine at a trace level. This method is based on the selective reaction of 2,9-dimethyl-1,10-phenanthroline (neocuproine) with copper(I) to produce a yellow-orange hydrophobic complex in a neutral or slightly acidic buffer solution (adjusted to pH 5.9). Copper(II) was reduced to copper(I) ions by ascorbic acid as a weak reducer, which was added both to urine sample and mobile phase, respectively. A hydrophobic copper(I)–neocuproine chelate was determined by RP-LC–UV/VIS using a monolithic column Chromolith Performance RP-8e (100 × 4 mm I.D.) at 30.0 ± 0.1 °C with a methanol: aqueous buffer (pH 5.9, ammonium acetate and ascorbic acid 2.8 mmol L^?1) mobile phase at flow rate of 2.00 mL min^?1. Sample injection volume was 20 μL and detection was done at 453 nm. The method was validated over a concentration range of 0.09–11.50 μmol L^?1. The LOD of copper in human urine was found to be 0.07 μmol L^?1 concentration level, suitable for clinical analysis. The precision of the results, reported as the RSD, was below 4.6 % for copper concentration within range 0.5–5.0 μmol L^?1 in the spiked human urine samples.     

Properties of PAN-TBP extraction chromatographic material

Three production routes of the preparation of a solid extractant based on tributylphosphate (TBP) embedded in the polyacrylonitrile matrix (PAN) have been studied. The method of direct PAN coagulation with TBP was found to be not viable due to the significant TBP solubility in the coagulation bath. The most suitable PAN-TBP solid extractant was prepared by the well-known impregnation method of ready-made neat PAN beads. The kinetics of uranium extraction from 3 mol L^?1 HNO₃, the effect of nitrate and nitric acids concentrations on the value of weight distribution coefficients D _g as well as the uranium “extraction isotherm” were determined for this material. Uranium extraction was rather fast, approximately 1 h was sufficient for the equilibrium achievement. Capacity for the uranium uptake, measured in batch experiments on PAN-TBP for 0.048 mol L^?1 of uranium in 3 mol L^?1 nitric acid, was found to be q = 0.363 mmol g^?1 (58 % of the theoretical capacity). It was concluded that PAN-TBP material behaves like TBP in liquid–liquid extraction. Extraction capacity determined in column experiments was lower (by about 23 %) than expected from the “extraction isotherm” due to the TBP leaching out of the column. The thus prepared material is therefore not very suitable for multicycle extraction and stripping and can be used once, particularly for the analytical purposes.     

Simultaneous voltammetric determination of carbendazim and carbaryl in medicinal plant infusions with a boron-doped diamond electrode

This study is aimed to develop an electroanalytical methodology using a boron-doped diamond electrode to determine simultaneously and selectively carbendazim (CBZ) and carbaryl (CAR). In previous studies using cyclic voltammetry oxidation, peaks were observed at 1.03 V (CBZ) and 1.44 V (CAR), with characteristics of an irreversible process controlled by diffusion of species, with a supporting electrolyte of BR buffer (0.1 mol L^?1) and pH adjusted to 6.0. The differences between the potentials for both pesticides, about 400 mV, indicate the possibility of selective determination of CBZ and CAR. The square-wave voltammetric parameters were optimised. The best separation conditions were pH 6.0, square-wave frequency of 100 s^?1, pulse amplitude of 50 mV and scan increment of 2.0 mV. These parameters were used to obtain the calibration curves of CBZ and CAR. An analytical curve was constructed in the range concentration of CBZ of 1.3 mg L^?1 to 15.3 mg L^?1 and CAR of 1.0 mg L^?1 to 11.4 mg L^?1, respectively. The limits of detection (LOD) and limits of quantification (LOQ) for CBZ were 0.40 mg L^?1 and 1.30 mg L^?1, respectively. For CAR, the LOD and LOQ were 0.30 mg L^?1 and 1.00 mg L^?1, respectively. Sensitivity values were 0.78 and 2.60 µA/mg L^?1 for CBZ and CAR, respectively. The electroanalytical method was applied in Mikania glomerata infusions. The recovery values were 106.2% and 116.5% for CBZ and CAR, respectively. The results show that the developed method is suitable for application in medicinal plant samples.     

Sensitive Analysis of Wilforidine in Human Plasma by LC-APCI-MS/MS

Wilforidine is a potentially efficient medicine to cure autoimmune diseases. In this paper, a sensitive and selective liquid chromatographic method coupled with atmospheric -pressure chemical ionization mass spectrometry (LC–APCI–MS/MS) has been developed for quantification of wilforidine in human plasma. Samples were deproteinized with acetonitrile and cleaned by solid-phase extraction. The chromatographic separation was performed on an analytical RRHD C₁₈ column (50 × 2.1 mm) using ammonium acetate solution (10.0 mmol L^?1)/acetonitrile (30/70, v/v) as the mobile phase at a flow rate of 0.7 mL min^?1. Detection was carried out by the positive multiple reaction monitoring mode with transitions of m/z 780 → 684 for wilforidine, and 646 → 586 for aconitine (internal standard), respectively. The calibration curve was linear (r = 0.9991) in the concentration range of 0.5–100.0 μg L^?1 with a lower limit of quantification of 0.5 μg L^?1 in plasma. Intra- and inter-day relative standard deviations were less than 6.8 and 13.1 %, respectively, and the recoveries were between 88.0 and 96.0 %. This accurate and highly specific assay provides a useful method for evaluating the pharmacokinetics of wilforidine in human plasma.