Low electroosmotic flow measurement by tilting microchip

A novel method for low electroosmotic flow (EOF) rates measurement by tilting microchip which based upon the hydrostatic pressure conception and sampling zone method is described. Sampling zone could be detected in the tilting microchip but not in non-tilting one due to the hydrostatic pressure driven. The method is fulfilled to calculate low EOF rates by detecting the liquid flow velocity driven by hydrostatic pressure, and difference between the apparent mobility of the migrating analyte in two modes is caused by the effect of hydrostatic pressure. And then the EOF rates in unknown low EOF microchip can be calculated. Different microchannels modified with bovine serum albumin (BSA), myoglobin (MB) and polyvinyl alcohol (PVA) were used to verify the method, the EOF rate value was 1.73+/-0.03, 1.21+/-0.05, 0.34+/-0.04 x 10(-4)cm(2) V(-1)s(-1), respectively. The results obtained by the proposed method were agreed well with conventional methods.     

One‐step preparation and application of mussel‐inspired poly(norepinephrine)‐coated polydimethylsiloxane microchip for separation of chiral compounds

In this paper, using the self‐polymerization of norepinephrine (NE) and its favorable film‐forming property, a simple and green preparation approach was developed to modify a PDMS channel for enantioseparation of chiral compounds. After the PDMS microchip was filled with NE solution, poly(norepinephrine) (PNE) film was gradually formed and deposited on the inner wall of microchannel as permanent coating via the oxidation of NE by the oxygen dissolved in the solution. Due to possessing plentiful catechol and amine functional groups, the PNE‐coated PDMS microchip exhibited much better wettability, more stable and suppressed EOF, and less nonspecific adsorption. The water contact angle and EOF of PNE‐coated PDMS substrate were measured to be 13° and 1.68 × 10^?4 cm² V^?1 s^?1, compared to those of 108° and 2.24 × 10^?4 cm² V^?1 s^?1 from the untreated one, respectively. Different kinds of chiral compounds, such as amino acid enantiomer, drug enantiomer, and peptide enantiomer were efficiently separated utilizing a separation length of 37 mm coupled with in‐column amperometric detection on the PNE‐coated PDMS microchips. This facile mussel‐inspired PNE‐based microchip system exhibited strong recognition ability, high‐performance, admirable reproducibility, and stability, which may have potential use in the complex biological analysis.     

EOF measurement by detection of a sampling zone with end-channel amperometry in microchip CE

A simple method for EOF measurement by detection of sampling zones with end-channel amperometry in microchip CE is developed. This method is based on the principle of the Kohlrausch regulating function (KRF). A dilute electroactive ionic species is added to the BGE as a continuously eluting electrophore which is used as a probe. When a BGE-like sample at a different concentration is injected, a peak of sampling zone appears and the migration time is related to EOF. In a microchip CE with hybrid PDMS/glass channel, a cathodic EOF of the hybrid glass/PDMS microchip was measured by end-channel amperometry; the effects of sample concentration and different probes on EOF rate were discussed. The present method was applied to monitor EOF rates in glass and in PDMS microchips. There was no significant difference between the values of EOF rates measured by the present method and the current-monitoring method. Detection of nonelectroactive analytes K(+), Na(+), and Li(+) can also be accomplished by the indirect amperometric method. Hence, the effective mobility of analyte can be accurately obtained.     

Flow Injection and Batch Spectrophotometric Determination of Ibuprofen Based on its Competitive Complexation Reaction with Phenolphthalein‐β‐Cyclodextrin Inclusion Complex

Abstract

Rapid, simple, and accurate spectrophotometric method is presented for the determination of ibuprofen by batch and flow injection analysis methods. The method is based on ibuprofen competitive complexation reaction with phenolphthalein‐β‐cyclodextrin (PHP‐β‐CD) inclusion complex. The increase in the absorbance of the solution at 554 nm by the addition of ibuprofen was measured. Ibuprofen can be determined in the range 8.0×10^?6 ?3.2×10^?4 and 2.0×10^?5?5.0×10^?3 mol l^?1 by batch and flow methods, respectively. The limit of detection and limit of quantification were 6.19×10^?6 and 2.06×10^?5 mol l^?1 for batch and 1.77×10^?5 and 5.92×10^?5 mol l^?1 for flow method, respectively. The sampling rate in flow injection analysis method was 120±5 samples h^?1. The method was applied to the determination of pharmaceutical formulations.     

A novel solid-phase extraction method for separation and preconcentration of zirconium

This work assesses the use of modified natural clinoptilolite as an adsorptive material for separation and preconcentration of trace amounts of zirconium ions. A simple, rapid and economical method was developed for the preconcentration of trace amounts of zirconium in aqueous medium using 1-(2-pyridylazo)-2-naphthol as a complexing agent. Effect of sample pH, flow rate of sample and elution solutions, breakthrough volume and interference of several ions were studied. Determination of zirconium was made by ICP-AES technique. The sorption was quantitative in the pH range from 3.0 to 4.0, whereas quantitative desorption occurred instantaneously with 2 mol L^?1 hydrochloric acid. Linearity was maintained between 0.05 and 9.0 μg mL^?1. Relative standard deviations range from ±0.9% to ±2.3% (n?=?5). The detection limit was 0.1 ng mL^?1. Because of good recovery (>97%), this method is suitable for preconcentration and determination of zirconium in effluents containing trace amount of zirconium.     

Modified Screen-Printed Electrode for Potentiometric Determination of Copper(II) in Water Samples

Modified screen printed (SPE) and carbon paste electrodes (CPE) with phenanthroline–tetraphenyl borate ionophore [Phen:TPB] were fabricated for the determination of copper(II). The modified electrodes have linear responses over a wide concentration range (1 × 10^?6–1 × 10^?2 mol·L^?1) of copper(II) ion at 25 °C with divalent cationic slopes of 29.85 ± 0.58 and 29.45 ± 0.81 mV·decade^?1 and exhibit a detection limit of 1 × 10^?6 mol·L^?1 for SPE and CPE. The selectivity coefficient was measured using the match potential method in acetate buffer of pH = 4.2. The modified SPE and CPE sensors show high selectivity and sensitivity for determination of copper(II) and also show stable and reproducible response over a period of five and three months for SPE and CPE sensors, respectively. This method can be used for determination of copper(II) in water, soil, plant and fish tissue samples and the results obtained agreed with those obtained with atomic absorption spectrometer (AAS).     

On-line spectrophotometric determination of scandium after preconcentration on XAD-4 resin impregnated with nalidixic acid

An on-line scandium preconcentration and determination method was developed with spectrophotometer associated with flow injection. Scandium from aqueous sample solution of pH 4.5 was selectively retained in the minicolumn containing XAD-4 resin impregnated with nalidixic acid at a flow rate of 11.8 mL min^?1 as scandium–nalidixic acid complex. The scandium complex was desorbed from the resin by 0.1 mol L^?1 HCl at a flow rate of 3.2 mL min^?1 and mixed with arsenazo-III solution (0.05 % solution in 0.1 mol L^?1 HCl, 3.2 mL min^?1) and taken to the flow through cell of spectrophotometer where its absorbance was measured at 640 nm. The preconcentration factors obtained were 35 and 155; detection limits of 1.4 and 0.32 μg L^?1 and sample throughputs of 40 and 11 were obtained for preconcentration time of 60 and 300 s, respectively. The tolerance limits of many interfering cations like Th(IV), U (VI), rare-earths and anions like tartrate, citrate, oxalate and fluoride were improved. The method was successfully applied to the determination of scandium from mock seawater samples and good recovery was obtained. The method was also validated on certified reference material IAEA-SL-1 (lake sediment) and the result was in good agreement with the reported value.     

Concurrent determination and separation of inorganic cations and anions in microchip electrophoresis with precisely controlled high‐voltage

An improved method for the concurrent determination and separation of cations and anions by microchip electrophoresis with capacitively coupled contactless conductivity detection (ME‐C⁴D) is described. Two kinds of microchip structures were designed. The first microchip has a long bent separation channel. And for the defects of the first microchip, the second microchip with a Y‐type separation channel has been proposed. The background electrolyte (BGE) composed of 20 mm His/MES and 0.01 mm CTAB was optimized for inhibiting the electroosmotic flow (EOF). Due to the low electroosmotic flow, the cations and anions migrate in opposite directions and can be separated from each other. With the precisely controlled high‐voltage, cations and anions can be migrated in microchannels according to our requirements and sequentially detected by a C⁴D detector built in‐house. Samples containing K⁺, Na⁺, Li⁺, Cl⁻, F⁻ and PO₄³⁻ were analyzed simultaneously in a single run (within 140 s) by both methods. The reproducibility obtained by both methods remained below 5% for migration time and within 3.5–9.1% for peak areas. The proposed concurrent determination methods are inexpensive, simple, fast, ease of operation, high degree of integration.     

Indirect amperometric measurement of electroosmotic flow rates and effective mobilities in microchip capillary electrophoresis

End-channel indirect amperometry is based on the principle of Kohlrausch regulating function (KRF). A dilute electroactive ionic species is added to the background electrolyte as a continuously eluting electrophore, which is used as probe. The probe concentration variation with the omega value of KRF in the sampling zone was described schematically in this report. Either cathodic or anodic electroosmotic flow (EOF) rates were monitored in microchip. There was no significant difference between the values of EOF rates measured by present method and current-monitoring method. Detection of electroactive and nonelectroactive analytes can also be accomplished by indirect amperometric method. Hence, the effective mobility of analytes can be accurately calculated. And the response mechanism of nonelectroactive analytes K(+), Na(+) and Li(+) in the indirect method was speculated.     

Retention profile of Fe,Mn and Cu onto chemically treated polyurethane with carbon disulfide

Dithiocarbamate modified polyurethane foam (DTC-PUF) was synthesized as a new solid-phase extraction sorbent for the preconcentration and determination of Fe(II), Mn(II) and Cu(II) in environmental samples using flame atomic absorption spectrometry. Maximum extraction of the elements was achieved at pH 5–7 and flow rate 3 mL min^?1. Quantitative desorption was achieved by 10 mL from 1.0 mol L^?1 HCl solution. The capacity of the sorbent was 149.2 ± 0.5, 237.5 ± 0.2, 200.2 ± 0.1 μg g^?1 and the limit of detection was of 0.015, 0.015 and 0.012 μg mL^?1for Fe(II), Mn(II) and Cu(II), respectively. A preconcentration factor of 100 was obtained for all elements. The developed method was successfully applied to the determination of the tested elements in water (tap and lake) and plant (spinach and parsley leaves) samples and showed good recovery values from 98 to 111% with corresponding RSD values ranged from 0.6 to 8.6%.     

Rapid and Highly Sensitive HPLC and TLC Methods for Quantitation of Amlodipine Besilate and Valsartan in Bulk Powder and in Pharmaceutical Dosage Forms and in Human Plasma

Two simple, sensitive, and specific high-performance liquid chromatography and thin-layer chromatography methods were developed for the simultaneous estimation of Amlodipine besilate (AM) and Valsartan (VL). Separation by HPLC was achieved using a xTerra C18 column and methanol /acetonitrile /water/ 0.05% triethylamine in a ratio 40:20:30:10 by volume as mobile phase, pH was adjusted to 3 ± 0.1 with o-phosphoric acid. The flow rate was 1.2 mL min^?1. The linearity range was 0.2 to 2 µg mL^?1 for amlodipine besilate and 0.4 to 4 µg mL^?1 for Valsartan with a mean percentage recovery of 99.59 ± 0.523% and 100.61 ± 0.400% for amlodipine besilate and valsartan, respectively. The TLC method used silica gel 60 F₂₅₄ plates; the optimized mobile phase was ethyl acetate/ methanol / ammonium hydroxide (55:45:5 by volume). Quantitatively, the spots were scanned densitometrically at 237 nm. The range was 0.5–4.0 µg spot^?1 for amlodipine besilate and 2.0–12.0 µg spot^?1 for valsartan. The mean percentages recovery was 99.80 ± 0.451% and 100.61 ± 0.363% for amlodipine besilate and valsartan, respectively. The HPLC method was found to be simple, selective, precise, and reproducible for the estimation of both drugs from spiked human plasma.     

Preconcentration of trace amounts of cobalt (II) ions in water and agricultural products samples using of 5-(4-dimethylaminobenzylidene) rhodanin modified SBA-15 sorbent prior to FAAS determination

In the present study, the ?5-(4-dimethylaminobenzylidene)rhodanin-modified SBA-15? was applied as stable solid sorbent for the separation and preconcentration of trace amounts of cobalt ions in aqueous solution. SBA-15 was modified by ?5-(4-dimethylaminobenzylidene)rhodanin reagent. The sorption of Co²⁺ ions was done onto modified sorbent in the pH range of 6.8–7.9 and desorption occurred in 5.0 mL of 3.0 mol L^?1 HNO₃. The results exhibit a linear dynamic range from 0.01 to 6.0 mg L^?1 for cobalt. Intra-day (repeatability) and inter-day (reproducibility) for 10 replicated determination of 0.06 mg L^?1 of cobalt was ±1.82% and ?±1.97%?. Detection limit was 4.2 µg L^?1 (3S_b, n = 5) and preconcentration factor was 80. The effects of the experimental parameters, including the sample pH, flow rates of sample and eluent solution, eluent type and interference ions were studied for the preconcentration of Co²⁺. The proposed method was applied for the determination of cobalt in standard samples, water samples and agricultural products.     

Measurement of isomeric-yield ratios for the 197Au(γ,n)196m,gAu reactions induced by bremsstrahlung

We measured isomeric-yield ratios for the ¹⁹⁷Au(γ,n)^196m,gAu reactions with bremsstrahlung energies of 50-, 60-, 70- MeV, and 2.5-GeV at the two different electron linac of the Pohang accelerator laboratory by using the activation method. The photons were produced when a pulsed electron beam hit a thin tungsten target. The well-known photoactivation method was used and hence the induced activities in the irradiated foils were measured with the high-resolution γ-ray spectrometric system consisting of lithium drifted high-purity Germanium detector and a multichannel analyzer. The measured isomeric-yield ratios for the ¹⁹⁷Au(γ,n)^196m,gAu reactions were (4.95 ± 0.51) × 10^?4, (5.72 ± 0.72) × 10^?4, (6.03 ± 0.50) × 10^?4, and (9.27 ± 0.83) × 10^?4 for 50-, 60-, 70-MeV, and 2.5-GeV bremsstrahlung energies, respectively. The present results measured with the bremsstrahlung energy higher than 60-MeV are the first measurement.     

Determination of Nateglinide in Human Plasma by LC-ESI-MS and Its Application to Bioequivalence Study

To evaluate the bioequivalence of nateglinide, a rapid and specific liquid chromatographic-electrospray ionization mass spectrometric method was developed and validated to determine nateglinide for human plasma samples. The analyte was detected using electrospray positive ionization mass spectrometry in the selected ion monitoring mode. Tinidazole was used as the internal standard. A good linear relationship obtained in the concentration ranged from 0.05 to 16 μg mL^?1 (r ² = 0.9993). Lower limit of quantification was 0.05 μg mL^?1 using 100 μL of plasma sample. Intra- and inter-day relative standard deviations were 2.1–7.5 and 4.7–8.9%, respectively. Among the pharmacokinetic data obtained, T _max was 2.09 ± 1.06 h for reference formulation and 2.40 ± 0.97 h for test formulation. C _max was 4.17 ± 1.31 μg mL^?1 for reference formulation and 4.37 ± 1.53 μg mL^?1 for test formulation. The half-life (t _½) was 1.93 ± 0.44 h for reference formulation and 1.92 ± 0.29 h for test formulation. AUC_0–10h was 13.67 ± 4.36 μg h mL^?1 for reference formulation and 13.21 ± 4.09 μg h mL^?1 for test formulation. This method was successfully applied to the pharmacokinetic study in human plasma samples.     

Online thorium determination after preconcentration in a minicolumn having XAD-4 resin impregnated with N-benzoylphenylhydroxylamine by FI-spectrophotometry

A very sensitive and selective flow injection on-line determination method of thorium (IV) after preconcentration in a minicolumn having XAD-4 resin impregnated with N-benzoylphenylhydroxylamine is described. Thorium (IV) was selectively adsorbed from aqueous solution of pH 4.5 in a minicolumn at a flow rate of 13.6 mL min^?1, eluted with 3.6 mol dm^?3 HCl (5.6 mL min^?1), mixed with arsenazo-III (0.05% in 3.6 mol dm^?3 HCl stabilized with 1% Triton X-100, 5.6 mL min^?1) at confluence point and taken to the flow through cell of spectrophotometer where its absorbance was measured at 660 nm. Peak height was used for data analyses. The preconcentration factors obtained were 32 and 162, detection limits of 0.76 and 0.150 ??g L^?1, sample throughputs of 40 and 11 h^?1 for preconcentration times of 60 and 300 s, respectively. The tolerance levels for Zr(IV) and U(VI) metal ions is increased to 50-folds higher concentration to Th(IV). The proposed method was applied on different spiked tap water, sea water and biological sample and good recovery was obtained. The method was also applied on certified reference material IAEA-SL1 (Lake Sediment) for the determination of thorium and the results were in good agreement with the reported value.     

HPLC Analysis and Pharmacokinetic Study of Paeoniflorin after Intravenous Administration of a New Frozen Dry Powder Formulation in Rats

A simple and specific high performance liquid chromatographic (HPLC) method with UV detection using picroside II as the internal standard was developed and validated to determine the concentration of paeoniflorin in rat plasma and study its pharmacokinetics after an single intravenous administration of 40 mg kg^?1 paeoniflorin to Wistar rats. The analytes of interest were extracted from rat plasma samples by ethyl acetate after acidification with 0.05 mol L^?1 NaH₂PO₄ solution (pH 5.0). Chromatographic separation was achieved on an Agilent XDB C₁₈ column (250 × 4.6 mm I.D., 5 μm) with a Shim-pack GVP-ODS C₁₈ guard column (10 × 4.6 mm I.D., 5 μm) using a mobile phase consisting of acetonitrile–water–acetic acid (18:82:0.4, v/v/v) at a flow rate of 1.0 mL min^?1. The UV detection was performed at a wavelength of 230 nm. The linear calibration curves were obtained in the concentration range of 0.05–200.0 μg mL^?1 in rat plasma with the lower limit of quantification (LLOQ) of 0.05 μg mL^?1. The intra- and inter-day precisions in terms of % relative standard deviation (RSD) were lower than 5.7 and 8.2% in rat plasma, respectively. The accuracy in terms of % relative error (RE) ranged from ?1.9 to 2.6% in rat plasma. The extraction recoveries of paeoniflorin and picroside II were calculated to be 69.7 and 56.9%, respectively. This validated method was successfully applied to the pharmacokinetic study of a new paeoniflorin frozen dry power formulation. After single intravenous administration, the main pharmacokinetic parameters t _1/2, AUC_0-∞, CL_TOT, V _Z, MRT_0-∞ and V _ss were 0.739 ± 0.232 h, 43.75 ± 6.90 μg h mL^?1, 15.50 ± 2.46 L kg^?1 h^?1, 1.003 ± 0.401 L kg^?1, 0.480 ± 0.055 h and 0.444 ± 0.060 L kg^?1, respectively.     

Surface modification with BSA blocking based on in situ synthesized gold nanoparticles in poly(dimethylsiloxane) microchip

A stable BSA blocking poly(dimethylsiloxane) (PDMS) microchannel was prepared based on in situ synthesized PDMS–gold nanoparticles composite films. The modified microchip could successfully suppress protein adsorption. The assembly was followed by contact angle, charge-coupled device (CCD) imaging, electroosmotic flow (EOF) measurements and electrophoretic separation methods. Contact angle measurements revealed the coated surface was hydrophilic, water contact angle for coated chips was 45.2° compared to a water contact angle for native PDMS chips of 88.5°. The coated microchips exhibited reproducible and stable EOF behavior. With FITC-labeled myoglobin incubation in the coated channel, no fluorescence was observed with CCD image, and the protein exhibited good electrophoretic effect in the modified microchip.     

Hybrid flow analyzer for automatic hollow-fiber-assisted ionic liquid-based liquid-phase microextraction with in-line membrane regeneration

The proof-of-concept of a new methodology for in-line hollow-fiber (HF)-assisted three-phase liquid-phase microextraction (LPME) allowing for handling of the feed and acceptor aqueous solutions and of minute volumes of the organic extracting phase in a programmable flow mode is reported in this paper. The flow analyzer fosters in-line anchoring of ionic-liquid-laden extracting solution (10 % (v/v) methyltrioctyl ammonium chloride in kerosene) in the pores of a single-strand microporous polypropylene HF, and regeneration of the liquid-phase membrane itself for each individual analysis cycle in a fully automated mode. Using hexavalent chromium as a model analyte and 1,5-diphenylcarbazide as a chromogenic probe in the acceptor solution, the flow-based HF-LPME hyphenated system was harnessed to the clean-up of troublesome samples (viz., domestic wastewater and soil leachates) with concomitant enrichment of target species. Distinct extraction modes and chemistries were assessed for enhanced Cr(VI) permeability. A single sample plug was subjected to a twofold backward–forward flow extraction so as to decrease the thickness of the boundary layer at the HF shell side for improved extraction efficiency. Under the optimized physicochemical variables, a limit of detection of 4.6 μg?L^?1 Cr(VI), a dynamic linear range of up to 500 μg?L^?1 and intermediate precision better than 10 % were obtained for a sample volume of 2.8 mL buffered at pH 4 and a volume of organic extractant of 120 μL, with an enrichment factor of ca. 11 for a sample residence time in the donor compartment of merely 4.5 min. Analyte recoveries in domestic wastewaters were ≥83 % using external calibration with relative standard deviations better than 14 %, thereby demonstrating the expedient clean-up of samples with elevated content of dissolved organic carbon. The automatic HF-LPME method was validated in terms of bias against the SRM 2701 (NIST soil) preceded by the EPA alkaline digestion method 3060A. No significant differences between Cr(VI) concentration as obtained with the automatic HF-LPME system (546?±?57 mg?kg^?1) and the certified value (551.2?±?17.2 mg?kg^?1, expressed as mean ± combined uncertainty) were encountered at the 0.05 significance level.     

Electrochemical Study of Interaction Between Clozapine and DNA and Its Analytical Application

Abstract

The interaction between clozapine (CLZ) as an orally administrated antipsychotic drug with double stranded calf thymus DNA (dsDNA) was investigated at electrode surface using differential pulse voltammetry (DPV). Activated carbon paste electrode (CPE) was modified with dsDNA and used for monitoring the changes of the characteristics peak of CLZ in 0.05 M acetate buffer (pH 4.3). The adsorptive stripping voltammetry on dsDNA‐modified carbon paste electrode (dsDNA‐CPE) was used for determination of very low concentration of CLZ. Under optimal conditions, the oxidation peak current is proportional to CLZ concentration in the range of 7×10^?9?1.2×10^?6 mol l^?1 with a detection limit of 1.5×10^?9 mol l^?1 for 180 s accumulation time by DPV. The proposed dsDNA‐CPE was successfully used for determination of CLZ in human serum samples with recovery of 97.0±2.5%.