Stability-Indicating HPTLC Method for the Determination of Tamsulosin in Pharmaceutical Dosage Forms

A simple, sensitive, selective, precise and stability indicating high-performance thin-layer chromatographic method was developed for the determination of tamsulosin (TAM) in bulk and tablet formulation. Validation was carried out in compliance with International Conference on Harmonization guidelines. The method employed thin-layer chromatography aluminium plates pre-coated with silica gel 60F₂₅₄ as the stationary phase and the mobile phase consisted of acetonitrile/methanol/dichloromethane (2.0: 1.0: 2.0, v/v/v). This solvent system was found to give compact spots for tamsulosin (R _f = 0.27 ± 0.02). Densitometric analysis of TAM was carried out in the absorbance mode at 286 nm. Linear regression analysis showed good linearity (r ² = 0.9993) with respect to peak area in the concentration range of 300–800 ng per band. The method was validated for precision, accuracy, ruggedness and recovery. Limits of detection and quantitation were 8.49 and 25.72 ng per band, respectively. TAM was subjected to acid and alkali hydrolysis, oxidation, photo degradation, dry heat and wet heat treatment. The drug underwent degradation under acidic, basic and photolytic conditions. The degraded products were well separated from the pure drug. Statistical analysis proved that the developed method, used for quantification of TAM as a bulk drug and present in pharmaceutical tablets, was reproducible and selective.     

Determination of Dutasteride by LC: Validation and Application of the Method

A simple, rapid, and stability-indicating reversed-phase high-performance liquid chromatographic (LC) method for analysis for dutasteride has been successfully developed. Chromatography was performed on a 150 mm × 4.6 mm C₁₈ column with acetonitrile–water 60:40 (v/v) as isocratic mobile phase at 1.0 mL min^?1. Ultraviolet detection of dutasteride was at 210 nm. Its retention time was approximately 10 min and its peak was symmetrical. Response was a linear function of concentration over the range 0.2–1 μg mL^?1 (R ² = 0.997) and the limits of detection and quantitation were was 0.05 and 0.10 μg mL^?1, respectively. The method was validated for linearity, precision, repeatability, sensitivity, and selectivity. Selectivity was validated by subjecting dutasteride stock solution to photolytic, acidic, basic, oxidative, and thermal degradation. The peaks from the degradation products did not interfere with that from dutasteride. The method was used to quantify dutasteride in pharmaceutical preparations.     

Stability-Indicating HPTLC Method for the Determination of Tamsulosin in Pharmaceutical Dosage Forms

A simple, sensitive, selective, precise and stability indicating high-performance thin-layer chromatographic method was developed for the determination of tamsulosin (TAM) in bulk and tablet formulation. Validation was carried out in compliance with International Conference on Harmonization guidelines. The method employed thin-layer chromatography aluminium plates pre-coated with silica gel 60F₂₅₄ as the stationary phase and the mobile phase consisted of acetonitrile/methanol/dichloromethane (2.0: 1.0: 2.0, v/v/v). This solvent system was found to give compact spots for tamsulosin (R _f = 0.27 ± 0.02). Densitometric analysis of TAM was carried out in the absorbance mode at 286 nm. Linear regression analysis showed good linearity (r ² = 0.9993) with respect to peak area in the concentration range of 300–800 ng per band. The method was validated for precision, accuracy, ruggedness and recovery. Limits of detection and quantitation were 8.49 and 25.72 ng per band, respectively. TAM was subjected to acid and alkali hydrolysis, oxidation, photo degradation, dry heat and wet heat treatment. The drug underwent degradation under acidic, basic and photolytic conditions. The degraded products were well separated from the pure drug. Statistical analysis proved that the developed method, used for quantification of TAM as a bulk drug and present in pharmaceutical tablets, was reproducible and selective.

     

Stability-Indicating Chromatographic Methods for Simultaneous Determination of Mosapride and Pantoprazole in Pharmaceutical Dosage Form and Plasma Samples

Simple, sensitive, selective, precise, and stability-indicating thin-layer chromatography (TLC) and high-performance liquid chromatography (HPLC) methods for the determination of mosapride and pantoprazole in pharmaceutical tablets were developed and validated as per the International Conference on Harmonization guidelines. The TLC method employs aluminum TLC plates precoated with silica gel 60F₂₅₄ as the stationary phase and ethyl acetate/methanol/toluene (4:1:2, v/v/v) as the mobile phase to give compact spots for mosapride (R _f 0.73) and pantoprazole (R _f 0.45) separated from their degradation products; the chromatogram was scanned at 276 nm. The HPLC method utilizes a C18 column and a mobile phase consisting of acetonitrile/methanol/20 mM ammonium acetate (4:2:4, v/v/v) at a flow rate of 1.0 mL min^?1 for the separation of mosapride (t _R 11.4) and pantoprazole (t _R 4.4) from their degradation products. Quantitation was achieved with UV detection at 280 nm. The same HPLC method was successfully used in performing calibrations in lower concentration ranges for both drugs in human plasma using ezetimibe as internal standard. The methods were validated in terms of accuracy, precision, linearity, limits of detection, and limits of quantification. Mosapride and pantoprazole were exposed to acid hydrolysis and then analyzed by the proposed methods. As the methods could effectively separate the drugs from their degradation products, these techniques can be employed as stability-indicating methods that have been successively applied to pharmaceutical formulations without interference from the excipients. Moreover the HPLC method was successfully used in the determination of both drugs in spiked human plasma.     

Study of the Degradation Kinetics of Carvedilol by Use of a Validated Stability-Indicating LC Method

The objectives of this investigation were to establish a validated stability-indicating LC method for assay of carvedilol and to study the degradation behaviour of the drug under different ICH-recommended stress conditions. Chromatographic separation was achieved on a C₁₈ column with 55:45 (%, v/v) acetonitrile–0.02 m phosphate buffer, pH 3.5, as mobile phase at a flow rate of 1.0 mL min^?1; detection was by UV absorbance at 242 nm. The method was validated for linearity, precision, accuracy, robustness, specificity, and sensitivity, with the bulk drug. The drug was subjected to forced degradation and peaks of all the degradation products were well resolved from that of the pure drug, with significantly different retention times, which indicates the specificity and stability-indicating properties of the method. First-order degradation kinetics of carvedilol were observed under acidic and alkaline conditions. When the utility of the method was verified by analysis of the drug in marketed tablets and a nano-emulsion formulation, the assay was found to be 98.60–99.61 and 99.52–99.87, respectively. These results indicate the method can be successfully used for routine analysis of carvedilol in the bulk drug and in pharmaceutical dosage forms.     

Stability-Indicating HPTLC Method for Analysis of Moclobemide, and Use of the Method to Study Degradation Kinetics

A sensitive, selective, precise, and stability-indicating HPTLC method for analysis of moclobemide in the bulk drug and in formulations has been established and validated. Aluminium TLC plates precoated with silica gel 60 F₂₅₄ were used with benzene–methanol–40% ammonia 7:3:0.1 (v/v) as mobile phase. Densitometric analysis was performed in absorbance mode at 238 nm. Compact bands were obtained for moclobemide (R _F 0.67 ± 0.02; n = 6). The drug was subjected to acidic and alkaline hydrolysis, oxidation, dry heat treatment, and photodegradation. The drug undergoes degradation under acidic, basic, and oxidising conditions. The degradation products were well resolved from the pure drug with significantly different R _F values, so the method can be regarded as stability-indicating. Response to moclobemide was a linear function of amount in the range 50–600 ng per band, with a correlation coefficient, r ², of 0.9967 ± 0.51. LOD and LOQ, determined experimentally, were 10 and 30 ng per band, respectively. Statistical analysis proves the method is repeatable and specific for analysis of moclobemide. The method was used to investigate the kinetics of alkaline degradation. The Arrhenius plot was constructed and the activation energy calculated.     

Application of Multicriteria Methodology in the Development of Improved RP-LC-DAD for Determination of Rizatriptan and Its Degradation Products

A simple, rapid, and stability-indicating reversed-phase high-performance liquid chromatographic (LC) method for analysis for dutasteride has been successfully developed. Chromatography was performed on a 150 mm × 4.6 mm C₁₈ column with acetonitrile–water 60:40 (v/v) as isocratic mobile phase at 1.0 mL min⁻¹. Ultraviolet detection of dutasteride was at 210 nm. Its retention time was approximately 10 min and its peak was symmetrical. Response was a linear function of concentration over the range 0.2–1 μg mL⁻¹ (R ² = 0.997) and the limits of detection and quantitation were was 0.05 and 0.10 μg mL⁻¹, respectively. The method was validated for linearity, precision, repeatability, sensitivity, and selectivity. Selectivity was validated by subjecting dutasteride stock solution to photolytic, acidic, basic, oxidative, and thermal degradation. The peaks from the degradation products did not interfere with that from dutasteride. The method was used to quantify dutasteride in pharmaceutical preparations.

     

Boronate-Containing Copolymer Grafted on Eupergit C as Matrix for Affinity Chromatography: Isotherms and Kinetics Study

A stability-indicating HPLC method has been developed and subsequently validated for the simultaneous determination of domperidone and pantoprazole in commercial tablets. The proposed HPLC method utilizes Phenomenex^® Gemini C₁₈ column (150 mm × 4.6 mm i.d., 5 μm) and mobile phase consisting of methanol-acetonitrile-20 mM dipotassium hydrogen phosphate and phosphoric acid buffer pH 7.0 (20:33:47, v/v/v) at a flow rate of 1.19 mL min^?1. Quantitation was achieved with UV detection at 285 nm based on peak area with linear calibration curves at concentration ranges 0.5–5.0 μg mL^?1 for domperidone and 1.0–10 μg mL^?1 for pantoprazole (R ² > 0.999 for both drugs). The method was validated in terms of accuracy, precision, linearity, limits of detection, limits of quantitation and robustness. This method has been successively applied to pharmaceutical formulation and no interference from the tablet excipients was found. Domperidone, pantoprazole and their combination drug product were exposed to acid, base and neutral hydrolysis, oxidation, dry heat and photolytic stress conditions and the stressed samples were analyzed by the proposed method. As the proposed method could effectively separate the drug from its degradation products, it can be employed as stability-indicating method for the determination of instability of these drugs in bulk and commercial products.     

Stability-Indicating Chromatographic Methods for Simultaneous Determination of Mosapride and Pantoprazole in Pharmaceutical Dosage Form and Plasma Samples

Simple, sensitive, selective, precise, and stability-indicating thin-layer chromatography (TLC) and high-performance liquid chromatography (HPLC) methods for the determination of mosapride and pantoprazole in pharmaceutical tablets were developed and validated as per the International Conference on Harmonization guidelines. The TLC method employs aluminum TLC plates precoated with silica gel 60F₂₅₄ as the stationary phase and ethyl acetate/methanol/toluene (4:1:2, v/v/v) as the mobile phase to give compact spots for mosapride (R _f 0.73) and pantoprazole (R _f 0.45) separated from their degradation products; the chromatogram was scanned at 276 nm. The HPLC method utilizes a C18 column and a mobile phase consisting of acetonitrile/methanol/20 mM ammonium acetate (4:2:4, v/v/v) at a flow rate of 1.0 mL min⁻¹ for the separation of mosapride (t _R 11.4) and pantoprazole (t _R 4.4) from their degradation products. Quantitation was achieved with UV detection at 280 nm. The same HPLC method was successfully used in performing calibrations in lower concentration ranges for both drugs in human plasma using ezetimibe as internal standard. The methods were validated in terms of accuracy, precision, linearity, limits of detection, and limits of quantification. Mosapride and pantoprazole were exposed to acid hydrolysis and then analyzed by the proposed methods. As the methods could effectively separate the drugs from their degradation products, these techniques can be employed as stability-indicating methods that have been successively applied to pharmaceutical formulations without interference from the excipients. Moreover the HPLC method was successfully used in the determination of both drugs in spiked human plasma.

     

Stability-Indicating LC Determination of a New Antihypertensive, Olmesartan Medoxomil in Tablets

A stability-indicating liquid chromatographic method was developed and validated for quantitative determination of olmesartan medoxomil (OLM) in coated tablets in the presence of degradation products generated under stress conditions. An isocratic LC separation was performed using a Phenomenex RP-18 column using a mobile phase consisting of water:triethylamine:acetonitrile (60:0.3:40 v/v/v, pH adjusted to 6.3 with phosphoric acid). The flow rate was 1.2 mL min^?1 and the detection was achieved with a photodiode array detector set at 257 nm. The response was linear over a range of 10.0 to 30.0 μg mL^?1 (r = 0.9999). The specificity and stability-indicating capability of the method was verified subjecting the reference substance and drug product to hydrolytic, oxidative, photolytic, and thermal stress conditions. The method showed a good and consistent recovery (100.2%) with low intra- and inter-day relative standard deviation (RSD) (≤1.0%). A considerable degradation occurred in all stress conditions and the degradation product was well resolved from the main peak. There was no interference of the excipients in the determination of the active pharmaceutical ingredient. Thus, the proposed method was found to be stability-indicating and can be used for routine analysis for quantitative determination of OLM in coated tablets without the interference of major degradation products.     

Selective Densitometric Analysis of Cephalosporins Using Dragendorff’s Reagent

A simple, selective, precise, and stability-indicating thin-layer chromatographic method has been developed and validated for analysis of the cephalosporins cefpodoxime proxetil, ceftriaxone sodium, ceftazidime pentahydrate, cefotaxime sodium, cefoperazone sodium, cefazolin sodium, and cefixime in the bulk drug and in pharmaceutical formulations. TLC was performed on aluminium sheets precoated with silica gel G 60F₂₅₄ as stationary phase. The mobile phases chosen for development gave compact spots for all the drugs (R _F values 0.43–0.60). The separated compounds were visualized as orange spots by spraying with Dragendorff’s reagent. Linear regression analysis data for the calibration plots revealed good linear relationships between response and amounts of the drugs with correlation coefficients ranging from 0.9977 to 0.9998 and determination coefficients ranging from 0.9954 to 0.9996 over the concentration ranges 5–25 μg per spot for cefpodoxime proxetil, ceftriaxone sodium, and ceftazidime pentahydrate and 10–50 μg per spot for cefotaxime sodium, cefoperazone sodium, cefazolin sodium, and cefixime. The method was validated for precision, recovery, and robustness. Limits of detection and quantitation for the drugs ranged from 0.35 to 2.48 and from 1.07 to 7.50 μg per spot, respectively. The method was successfully applied to analysis of the drugs in their pharmaceutical dosage forms with good precision and accuracy. The method can also be used as a stability-indicating assay.     

Stress Degradation Studies on Dutasteride and Development of a Stability-Indicating HPLC Assay Method for Bulk Drug and Pharmaceutical Dosage Form

A simple stability-indicating LC method has been developed for the quantitative determination of dutasteride in bulk drug samples and in pharmaceutical dosage forms in the presence of degradation products. The retention time of dutasteride is about 7 min. The drug was subjected to stress conditions of hydrolysis, oxidation, photolysis and thermal degradation. Degradation was found to occur under hydrolysis and to a lesser extent under oxidation conditions but the compound was stable to photolytic and thermal stress. The assay of stress samples was calculated against a reference standard and the mass balance was found close to 99.3%. The developed method was validated with respect to linearity, accuracy, precision and ruggedness.     

A Validated Stability-Indicating TLC Method for Determination of Forskolin in Crude Drug and Pharmaceutical Dosage Form

A simple, accurate, selective, precise, economical and stability-indicating high-performance thin-layer chromatographic method for analysis of forskolin in crude drug and in pharmaceutical dosage form was developed and validated. The method was developed on TLC aluminium plates precoated with silica gel 60F-254 using solvent system benzene:methanol (9:1, v/v), which gives compact spot of forskolin (R _f value 0.25 ± 0.02). Densitometric analysis of forskolin was carried out in the absorbance mode at 545 nm after spraying with anisaldehyde sulphuric acid. The linear regression analysis data for the calibration plots showed good linear relationship with r = 0.994 and 0.994 with respect to peak height and peak area, respectively, in the concentration range 100–1,000 ng per spot. The limits of detection and quantification were 8.1 and 26.9 ng per spot, respectively. The proposed method was applied for determination of forskolin in Coleus forskohlii root and in capsule dosage forms, which showed 0.18 and 0.57% w/w of forskolin. Forskolin was subjected to acid and alkali hydrolysis, oxidation, photodegradation and heat degradation. It was observed that the drug is susceptible to acid, base hydrolysis, oxidation, photo-oxidation and heat degradation. Statistical analysis proves that the method is repeatable, selective and accurate for the estimation of forskolin in crude drug and in pharmaceutical dosage forms. The developed method effectively resolved the forskolin from components of C. forskohlii root, from excipients of capsule as well as the degradation products of forskolin hence, it can be employed for routine analysis and as a stability-indicating method.     

Application of a validated stability-indicating densitometric thin-layer chromatographic method to stress degradation studies on moxifloxacin

A simple, sensitive, selective, precise and stability-indicating high-performance thin-layer chromatographic (HPTLC) method for densitometric determination of moxifloxacin both as a bulk drug and from pharmaceutical formulation was developed and validated as per the International Conference on Harmonization (ICH) guidelines. The method employed TLC aluminium plates pre-coated with silica gel 60F-254 as the stationary phase and the mobile phase consisted of n-propanol-ethanol-6 M ammonia solution (4:1:2, v/v/v). Densitometric analysis of moxifloxacin was carried out in the absorbance mode at 298 nm. Compact spots for moxifloxacin were found at R_f value of 0.58 ± 0.02. The linear regression analysis data for the calibration plots showed good linear relationship with r = 0.9925 in the working concentration range of 100-800 ng spot⁻¹. The method was validated for precision, accuracy, ruggedness, robustness, specificity, recovery, limit of detection (LOD) and limit of quantitation (LOQ). The LOD and LOQ were 3.90 and 11.83 ng spot⁻¹, respectively. Drug was subjected to acid and alkali hydrolysis, oxidation, dry heat, wet heat treatment and photodegradation. All the peaks of degradation products were well resolved from the standard drug with significantly different R_f values. Statistical analysis proves that the developed HPTLC method is reproducible and selective. As the method could effectively separate the drug from its degradation products, it can be employed as stability-indicating one. Moreover, the proposed HPTLC method was utilized to investigate the kinetics of the acidic and alkaline degradation processes at different temperatures. Arrhenius plot was constructed and apparent pseudo-first-order rate constant, half-life and activation energy were calculated. In addition the pH-rate profile for degradation of moxifloxacin in constant ionic strength buffer solutions within the pH range 1.2-10.8 was studied.     

Stability-Indicating LC Method for the Determination of Olmesartan in Bulk Drug and in Pharmaceutical Dosage Form

A novel stability-indicating LC assay method was developed and validated for quantitative determination of olmesartan in bulk drugs and in pharmaceutical dosage form in the presence of degradation products generated from forced degradation studies. An isocratic, reversed phase LC method was developed to separate the drug from the degradation products, using an Ace5-C18 (250 mm × 4.6 mm, 5 μm) column, and 50 mM ammonium acetate (pH-5.5 by acetic acid) and acetonitrile (70:30 v/v) as a mobile phase. The detection was carried out at the wavelength of 235 nm. The olmesartan was subjected to stress conditions of hydrolysis (acid, base), oxidation, photolysis and thermal degradation. Degradation was observed for olmesartan in acid, base and in 30% H₂O₂ conditions. The drug was found to be stable in the other stress conditions attempted. The degradation products were well resolved from the main peak. The percentage recovery of olmesartan ranged from (99.89 to 100.95%) in pharmaceutical dosage form. The developed method was validated with respect to linearity, accuracy (recovery), precision, specificity and robustness. The forced degradation studies prove the stability-indicating power of the method.

     

Stability-Indicating LC Determination of a New Antihypertensive,Olmesartan Medoxomil in Tablets

A stability-indicating liquid chromatographic method was developed and validated for quantitative determination of olmesartan medoxomil (OLM) in coated tablets in the presence of degradation products generated under stress conditions. An isocratic LC separation was performed using a Phenomenex RP-18 column using a mobile phase consisting of water:triethylamine:acetonitrile (60:0.3:40 v/v/v, pH adjusted to 6.3 with phosphoric acid). The flow rate was 1.2 mL min⁻¹ and the detection was achieved with a photodiode array detector set at 257 nm. The response was linear over a range of 10.0 to 30.0 μg mL⁻¹ (r = 0.9999). The specificity and stability-indicating capability of the method was verified subjecting the reference substance and drug product to hydrolytic, oxidative, photolytic, and thermal stress conditions. The method showed a good and consistent recovery (100.2%) with low intra- and inter-day relative standard deviation (RSD) (≤1.0%). A considerable degradation occurred in all stress conditions and the degradation product was well resolved from the main peak. There was no interference of the excipients in the determination of the active pharmaceutical ingredient. Thus, the proposed method was found to be stability-indicating and can be used for routine analysis for quantitative determination of OLM in coated tablets without the interference of major degradation products.

     

Forced Degradation Study to Develop and Validate Stability-Indicating RP-LC for Quantification of Ropinirole Hydrochloride in Its Modified Release Tablets

A forced degradation study on ropinirole hydrochloride in bulk and in its modified release tablets was conducted under the conditions of hydrolysis, oxidation and photolysis in order to develop an isocratic stability-indicating LC-UV method for quantification of the drug in tablets. An impurity peak in standard solution was found to increase under acidic and neutral hydrolytic conditions while another degradation product was formed under alkaline condition. The drug and its degradation products were optimally resolved on a Hypersil C₁₈ column with mobile phase composed of diammonium hydrogen orthophosphate (0.05 M; pH 7.2), tetrahydrofuran and methanol (80:15:5% v/v) at a flow rate of 1.0 mL min^?1 at 30 °C using 250 nm as detection wavelength. The method was linear in the range of 0.05–50 μg mL^?1 drug concentrations. The %RSD of inter- and intra-day precision studies was <1. The system suitability parameters remained unaffected during quantification of the drug on three different LC systems. Excellent recoveries (101.59–102.28%) proved that the method was sufficiently accurate. The LOD and LOQ were found to be 0.012 and 0.040 μg mL^?1, respectively. Degradation behaviour of the drug in both bulk and tablets was similar. The drug was very unstable to hydrolytic conditions but stable to oxidative and photolytic conditions. The method can be used for rapid and accurate quantification of ropinirole hydrochloride in tablets during stability testing. Based on chemical reactivity of ropinirole in different media, the degradation products were suspected to be different from the known impurities of the drug.     

UPLC Method for Determination of Moxonidine and Its Degradation Products in Active Pharmaceutical Ingredient and Pharmaceutical Dosage Form

A simple, rapid, isocratic, stability-indicating reverse phase ultra-performance liquid chromatographic (RP-UPLC) method was developed and validated for the routine analysis of moxonidine in the presence of its degradation products in active pharmaceutical ingredient and pharmaceutical dosage forms. Forced degradation studies were performed according to the guidance of International Conference for Harmonization and were used to evaluate moxonidine intrinsic stability. The drug was subjected to acid, neutral and base hydrolysis as well as to oxidative, thermal and photolytic decomposition in both solution and solid state. The drug appeared to be unstable towards acid and base hydrolysis. To achieve desirable conditions for UPLC analysis, the method development was done with the assistance of experimental design and multivariate optimization methodology by means of Derringer’s desirability function. Stress samples were analyzed according to the experimental plan for fractional factorial screening design and Box-Behnken optimization design. The chromatographic separation was achieved on a C₁₈ Hypersil Gold aq. column (100 mm × 2.1 mm, 1.9 μm) with the mobile phase consisting of methanol–ammonium acetate buffer (10 mM, pH 3.43) mixture (0.9:99.1, v/v) pumped at a flow rate of 870 μL min^?1 and detection wavelength of 255 nm. The UPLC–MS and UPLC–MS/MS analyses were further used to characterize the found degradation products. The validation of the proposed method was also performed considering selectivity, linearity, accuracy, precision, limit of detection and limit of quantification, and the results indicated that the method fulfilled all required criteria. The method was successfully applied to the analysis of commercial tablets.     

An Improved Narrow-Bore LC Method for Quantification of Alfuzosin in Pharmaceutical Formulations

A simple rapid and stability-indicating LC method using a narrow-bore column has been developed, fully validated, and applied to the quantification of alfuzosin in pharmaceutical formulations. Chromatography was achieved isocratically on a narrow-bore, 5-μm particle size, C₈ analytical column. The mobile phase was a 35:65 (v/v) 0.0125 m ammonium formate–acetonitrile at a flow rate of 0.35 mL min^?1. Detection was by UV absorption at 245 nm. Evaluation over the range 200–800 ng mL^?1 revealed linearity was good. Limits of detection and quantification for alfuzosin were 22.9 and 69.5 ng mL^?1, respectively. Intra-day and inter-day RSD were less than 6.4%, and the relative percentage error was less than ?1.7% (n = 5). Accelerated degradation performed under different stress conditions including oxidation, hydrolysis, and heat, proved the selectivity of the procedure. The method was successfully used for quality-control and content-uniformity testing of commercial tablets.     

Stability Indicating RP-LC Method for the Determination of Gemifloxacin Mesylate

The present study describes the degradation of gemifloxacin mesylate under different International Conference on Harmonization prescribed stress conditions (hydrolysis, oxidation, dry and wet heat and photolysis) and application of a specific and selective stability-indicating reversed-phase liquid chromatography assay. Separation of drug and degradation products was successfully achieved on a HiQ-SiL C₈ column using 10 mM potassium dihydrogen orthophosphate (pH adjusted to 3.0 with o-phosphoric acid)–acetonitrile (65:35, v/v) at a flow rate of 1 mL min⁻¹ and detection at 273 nm.