Trace element determination in thorium oxide using total reflection X-ray fluorescence spectrometry

Applicability of Total Reflection X-ray Fluorescence (TXRF) spectrometry for the determination of trace metals at concentration of µg/g level in thorium oxide was studied. The TXRF spectrometer was calibrated using a multielement standard solution and the method was validated by analyzing another multielement standard solution. Sample preparation conditions were optimized for the TXRF determinations of trace metals in thorium oxide. The elements K, Ca, V, Cr, Mn, Fe, Co, Ni, Cu, Zn, Sr, Y, Ba and Pb present in thorium oxide standards were determined after dissolving them in HNO₃/HF mixture and separating the bulk matrix, thorium, by solvent extraction using tri-n-butyl phosphate (TBP) and tri-n-octyl phosphine oxide (TOPO) as extractants. A comparison of TXRF determined concentrations of trace elements Ca, V, Cr, Mn, Fe, Ni and Cu with the certified values shows that TXRF determined concentrations have an RSD of 20% (1 s for n = 4) and are within an agreement of 20% of the certified values in most of the cases.     

Analysis of nutrition-relevant trace elements in human blood and serum by means of total reflection X-ray fluorescence (TXRF) spectroscopy

In clinical service laboratories, one of the most common analytical tasks with regard to inorganic traces is the determination of the nutrition-relevant elements Fe, Cu, Zn, and Se.     

Analysis of mineral water from Brazil using total reflection X-ray fluorescence by synchrotron radiation

The total reflection X-ray fluorescence using synchrotron radiation (SRTXRF) has become a competitive technique for the determination of trace elements in samples that the concentrations are lower than 100 ng ml⁻¹. In this work, thirty-seven mineral waters commonly available in supermarkets of Rio de Janeiro, Brazil, were analyzed by SRTXRF. The measurements were performed at the X-Ray Fluorescence Beamline at Brazilian National Synchrotron Light Laboratory (LNLS), in Campinas, São Paulo, using a polychromatic beam with maximum energy of 20 keV for the excitation. Standard solutions with gallium as internal standard were prepared for calibration of the system. Mineral water samples of 10 μl were added to Perspex sample carrier, dried under infrared lamp and analyzed for 200 s measuring time. It was possible to determine the concentrations of the following elements: Si, S, K, Ca, Ti, Cr, Mn, Ni, Cu, Zn, Ge, Rb, Sr, Ba and Pb. The elemental concentration values were compared with the limits established by the Brazilian legislation.     

Method and mechanism of vapor phase treatment–total reflection X-ray fluorescence for trace element analysis on silicon wafer surface

Vapor phase treatment (VPT) is a pretreatment with hydrofluoric acid vapor to raise the sensitivity of total reflection X-ray fluorescence spectroscopy (TXRF) for trace metal analysis on silicon wafers. The International Organization for Standardization/Technical Committee 201/Working Group 2 (ISO/TC201/WG2) has been investigating the method to analyze 10⁹ atoms/cm² level of metallic contamination on the silicon wafer surface. Though VPT can enhance the TXRF signal intensity from the metallic contamination, it has turned out that the magnitude of the enhancement varies with the type of methods and the process conditions. In this study, approaches to increase TXRF intensity by VPT are investigated using a fuming chamber in an automated VPD instrument. Higher signal intensity can be obtained when condensation is formed on the sample surface in a humidifying atmosphere and with a decreasing stage temperature. Surface observations with SEM and AFM show that particles with ~ 4 μm in diameter are formed and unexpectedly they are dented from the top surface level.     

Discriminant analysis of trace elements in normal,benign and malignant breast tissues measured by total reflection X-ray fluorescence

In this work total reflection X-ray fluorescence spectrometry has been employed to determine trace element concentrations in different human breast tissues (normal, normal adjacent, benign and malignant). A multivariate discriminant analysis of observed levels was performed in order to build a predictive model and perform tissue-type classifications. A total of 83 breast tissue samples were studied. Results showed the presence of Ca, Ti, Fe, Cu and Zn in all analyzed samples. All trace elements, except Ti, were found in higher concentrations in both malignant and benign tissues, when compared to normal tissues and normal adjacent tissues. In addition, the concentration of Fe was higher in malignant tissues than in benign neoplastic tissues. An opposite behavior was observed for Ca, Cu and Zn. Results have shown that discriminant analysis was able to successfully identify differences between trace element distributions from normal and malignant tissues with an overall accuracy of 80% and 65% for independent and paired breast samples respectively, and of 87% for benign and malignant tissues.     

Applicability of direct total reflection X-ray fluorescence analysis for selenium determination in solutions related to environmental and geochemical studies

A significant amount of environmental studies related to selenium determination in different environmental compartments have been published in the last years due to the narrow range between the Se nutritious requirement as essential element and toxic effects upon exposure. However, the direct analysis of complex liquid samples like natural waters and extraction solutions presents significant problems related to the low Se concentrations and the complicated matrix of this type of samples.     

Determination of trace elements in planktonic microcrustaceans using total reflection X-ray fluorescence (TXRF): First results from two Chilean lakes

First results are described from the application of a recently developed dry method for determination of elements in single specimens of freshwater microcrustaceans, using total reflection X-ray fluorescence spectrometry (TXRF). This method is a powerful, non-destructive technique for quantifying the trace element content of minute biological samples with a dry weight of 3–50 g. Three different freshwater microcrustaceans were sampled, from the natural, uncontaminated Lake Laja and from the artificial Rapel reservoir which is slightly contaminated by drainage water from a copper mine. Single specimens of Daphnia pulex, Bosmina chilensis, and Ceriodaphnia dubia were prepared using a modification of the dry method and measured by TXRF. The results showed that both As, Mn, Fe, Ni, Zn, and Cu content and the bioaccumulation of these metals were usually significantly different between the microcrustaceans from the two lakes. The largest difference was found for Cu which was eight times more concentrated in the two microcrustaceans from Rapel reservoir than it was in D. pulex from Lake Laja.     

Analytical approaches for Hg determination in wastewater samples by means of total reflection X-ray fluorescence spectrometry

At present, there is a considerable interest in Hg monitoring in wastewater samples due to its widespread occurrence and the high toxicity of most of its compounds. Hg determination in water samples by means of total reflection X-ray fluorescence spectrometry (TXRF) entails some difficulties due to the high vapor pressure and low boiling point of this element that produce evaporation and loss of Hg from the surface of the reflector during the drying process, commonly used for sample preparation in TXRF analysis.The main goal of the present research was to develop a fast and simple chemical strategy to avoid Hg volatilization during the analysis of wastewater samples by TXRF spectrometry. Three different analytical procedures were tested for this purpose: (i) increasing the viscosity of the wastewater sample by adding a non-ionic surfactant (Triton^® X-114), (ii) Hg immobilization on the quartz reflectors using the extractant tri-isobutylphosphine (Cyanex 471X) and (iii) formation of a stable and non-volatile Hg complex into the wastewater sample. The best analytical strategy was found to be the formation of a Hg complex with thiourea (pH = 10) before the deposition of 10 μL of sample on the reflector for following TXRF analysis. Analytical figures of merit such as linearity, limits of detection, accuracy and precision were carefully evaluated. Finally, the developed methodology was applied for the determination of Hg in different types of wastewater samples (industrial effluents, municipal effluents from conventional systems and municipal effluents from constructed wetlands).     

Applications of total reflection X-ray fluorescence spectrometry in trace element and surface analysis

Total reflection X-ray fluorescence spectrometry (TXRF) is presented as a genuine surface analytical technique. Its low information depth is shown to be the characteristic feature differentiating it from other energy dispersive X-ray fluorescence methods used for layer and surface analysis. The surface sensitivity of TXRF and its analytical capability together with the limitations of the technique are discussed here using typical applications including the contamination control of silicon wafers, thin layer analysis and trace element determination. For buried interfaces and implantation depth profiles in silicon a combination of TXRF and other techniques has been applied successfully. The TXRF method has the particular advantage of being calibrated without the need for standards. This feature is demonstrated for the example of the element arsenic.     

Possibilities and limitations of the total reflection X-ray fluorescence spectrometry for the determination of low Z elements in biological samples

The analytical capability of the laboratory scale vacuum total reflection X-ray fluorescence (TXRF) spectrometer (Wobistrax) was studied for the determination of the Z elements (Na, Mg, P, S, K and Ca) in different biological matrices represented by the following certified reference materials: MURST-ISS-A2 Antarctic krill, IAEA-331 spinach, NIST 1577a bovine liver, and SERONORM™ Trace Elements Serum Level 1.First, the stability of the response factors (relative sensitivity) against Ti internal standard was checked in the concentration range of 1 to 1000 mg/L in a diluted nitric acid matrix. It has been found that the upper limit of the analytical concentration range for K and Ca can be as high as 1000 mg/L; on the other hand, the remaining elements cannot be determined above a concentration of some tens mg/L.The established response factors were used for the elemental analysis of the four certified reference materials after normal-volume microwave assisted acid digestion. In the case of the serum sample, different preparation methods were compared as follow: direct analysis, microwave assisted acid digestion in normal-volume and micro-vessels, as well as the vapor-phase digestion directly on the TXRF carrier plates.On the basis of the results, the normal-volume digestion results in rather high dilution of the samples; thus, elements at low concentration could not be detected in some of the samples. On the other hand, this method offers the highest rate of both organic matrix decomposition and inorganic matrix dilution; thus, the background and the standard deviation of the results were the lowest. In general, this method was found to be useful for the analysis of samples with high dissolved (organic + inorganic) content if the analytes are present at a concentration considerable above the quantification limit.In the case of the microscale and the vapor-phase digestion, both the organic and inorganic matters remain at elevated concentration; thus, higher background and self-absorption of the fluorescent radiation occurred, deteriorating the analytical performance.     

Matrix effect on the detection limit and accuracy in total reflection X-ray fluorescence analysis of trace elements in environmental and biological samples

The effect of matrix contents on the detection limit of total reflection X-ray fluorescence analysis was experimentally investigated using a set of multielement standard solutions (500 ng/mL of each element) in variable concentrations of NH₄NO₃. It was found that high matrix concentration, i.e. 0.1–10% NH₄NO₃, had a strong effect on the detection limits for all investigated elements, whereas no effect was observed at lower matrix concentration, i.e. 0–0.1% NH₄NO₃.     

Cold plasma ashing improves the trace element detection of single Daphnia specimens by total reflection X-ray fluorescence spectrometry

The recently developed dry method for the element determination of single freshwater microcrustacean specimens (Daphnia) using total reflection X-ray fluorescence (TXRF) spectrometry showed that inhomogeneities of the biological material on the glass carriers resulted in some cases in high background and hampered the detection of certain trace elements (e.g. Cr, Ni). The aim of this study was to test how inhomogeneities of the biological material can be reduced using cold plasma ashing (CPA) techniques. For that, single specimens of the microcrustacean Daphnia pulex prepared according to the dry method were measured by TXRF before and after CPA. To determine the efficiency of the removal of organic matrix, the background and signal-to-background relationship of 28 samples were analyzed. The results showed (1) a highly significant reduction of the background by CPA fluctuating between 26 and 46% (all elements) and (2) a significant increase of the signal-to-background relationship by the factor 1.5–2.5 (all elements) and a much better detection of Cr, Pb, As and Se. The element concentrations (with exception of Cr, Ni and Pb) after ashing were in the same range or slightly higher than that before ashing. No significant differences between the two treatments were observed for Mn, As, Pb, Se (November), Sr (November), Cr (March) and Pb (March). The element concentration of P, K, Ca, Cu, Zn, Cr (November), Fe and Rb were significantly higher after ashing. In general, they increased by 1.5–13.6% and were highest for Rb (March) and P (November). In contrast, the element concentration of Ni and Cr (only March) decreased significantly after ashing (Ni: 91.6–92.1%, Cr: 91.3%). We recommend the use of CPA for biological material in the microgram-range as a routine method for TXRF analysis, especially when trace elements in minute concentrations are of interest.     

A solid phase extraction procedure for the simultaneous determination of total inorganic arsenic and trace metals in seawater: Sample preparation for total-reflection X-ray fluorescence

In this paper we present a procedure allowing total-reflection X-ray fluorescence spectrometry (TXRF) determinations of arsenic in water samples, especially in seawater samples. The procedure consists of an arsenate reduction step (performed by using a l-cysteine solution) followed by a complexation of As⁺³ with sodium dibenzyldithiocarbamate and solid phase extraction. The new procedure is a modification of a method developed by Prange and allows a simultaneous determination of As together with V, Fe, Ni, Cu, Zn, Pb, and U in seawater by TXRF. The procedure was tested using the Certified Reference Material CASS-4 and was later applied to regular seawater samples collected from the North Sea. The detection limit for arsenic is 10 ng L^− 1.     

A novel total reflection X-ray fluorescence procedure for the direct determination of trace elements in petrochemical products

A total reflection X-ray fluorescence (TXRF) procedure was developed for the determination of metal traces in petrochemical end products or intermediates for surfactant synthesis. The method combines a fast and straightforward sample preparation, i.e. deposition on the sample holder and evaporation of the sample matrix, with an efficient quantification method based on internal standardization (organic gallium standard). The method developed showed detection limits below 0.05 μg g^-1 and in most cases below 0.005 μg g^-1. Fifteen elements (Ca, Cd, Co, Cr, Cu, Fe, Mn, Mo, Ni, Pb, Rh, Sn, Sr, V and Zn) were determined in matrices such as paraffins, n-olefins, linear alkylbenzenes, long-chain alkyl alcohols and esters: typical metal contents were below 1 μg g^-1. The results were compared with the reference method ASTM D5708 (test method B) based on inductively coupled plasma optical emission spectroscopy: advantages and drawbacks of the two procedures were critically evaluated. The TXRF method developed showed comparable precision and absence of bias with respect to the reference method. A comparison of the performances of the two methods is presented.     

Construction of a windowless Si-anode X-ray tube for a more efficient excitation of low Z elements on Si-wafer surfaces in total reflection fluorescence analysis

To improve the achievable detection limits of low Z element with TXRF, a commercially available 2 kW X-ray tube (SEIFERT Type SF 60, Ahrensburg) with a 40 μm×8 mm fine focus has been modified. A windowless X-ray tube has been realized by removing the Be window out of the tube. The original Cu anode block has been changed to Al, because of sputtering reasons. A 4–6 μm thick pure silicon layer has been sputtered on the Al substrate. The geometry of the anode has been constructed in a specific way in order to optimize the photon flux of the X-ray beam concerning self-absorption and brilliance. Direct vacuum tight coupling to the measuring chamber and operation at 10⁻⁶ mbar vacuum was successfully shown. First measurements have been perfomed with a detector suitable for the detection of low energy photons in total reflection XRF geometry. Sodium has been analyzed on a Si-wafer surface and detection limits of 36 pg (corresponds to 3E9 atoms/cm²) have been achieved and are 10 times better than the detection limits for Na excited with a 1.3 kW Cr standard tube of 330 pg. With this developed X-ray tube the detection limits required by the Semiconductor industry for Si wafer surface contamination quality control are fulfilled.     

First combined total reflection X-ray fluorescence and grazing incidence X-ray absorption spectroscopy characterization of aeolian dust archived in Antarctica and Alpine deep ice cores

Aeolian mineral dust archived in polar and mid latitude ice cores represents a precious proxy for assessing environmental and climatic variations at different timescales. In this respect, the identification of dust mineralogy plays a key role. In this work we performed the first preliminary X-ray absorption spectroscopy (XAS) experiments on mineral dust particles extracted from Antarctic and from Alpine firn cores using grazing incidence geometry at the Fe K-edge. A dedicated high vacuum experimental chamber was set up for normal-incidence and total-reflection X-Ray Fluorescence and Absorption Spectroscopy analyses on minor amounts of mineral materials at the Stanford Synchrotron Radiation Laboratory. Results show that this experimental technique and protocol allows recognizing iron inclusion mineral fraction on insoluble dust in the 1–10 µg range.     

A new and direct method for the trace element determination in cauliflower by differential pulse polarography

Using the DPP polarograms of wet digested cauliflower sample in acetate buffer at pH values of 2, 4 and 6, Fe, Zn, Mo, Se, Cr, Cd, Pb, Ti and Cu quantities were determined. The best separation and determination conditions for Zn, Se and Mo was pH 2; for Cr, Zn, Mo and As was pH 4; for Pb pH 6, for Ti, Cu and Fe was pH 6-7 EDTA, for Cd pH 2 EDTA and for lead pH 6, all in acetate buffer. The trace element ranges for cauliflowers from two different seasons were (first figure for winter, the second for summer) for Se 120-250 μg g⁻¹, Fe 70-85 μg g⁻¹, Cu 320-150 μg g⁻¹, Ti 90-120 μg g⁻¹, Cr 130-630 μg g⁻¹, Zn 90-550 μg g⁻¹, Mo 170-230 μg g⁻¹, Cd 20 μg g⁻¹ (in winter) and Pb 130-300 μg g⁻¹ in dry sample. Cd was under the detection limit in summer. The length of digestion time had no effect on the recovery of copper, iron, molybdenum and zinc between 15 and 3 h of digestion.     

Determination of low atomic number elements at trace levels in uranium matrix using vacuum chamber total reflection X-ray fluorescence

Determinations of low atomic number elements Na, Mg and Al present at trace concentrations in uranium matrix were made by vacuum chamber total reflection X-ray fluorescence spectrometer for the first time. For this purpose, synthetic samples of uranium with known amounts of these low atomic number elements were prepared by mixing different volumes of their solutions with U solution of high purity. The concentrations of these elements in the samples were in the range of 100–300 μg/g with respect to uranium and 10–20 μg/mL in the solutions. Major matrix uranium was separated by solvent extraction with 30% solution of tri-n-butyl phosphate in dodecane. After the solvent extraction, aqueous phase containing trace elements was mixed with Sc internal standard and the samples were analyzed by vacuum chamber total reflection X-ray fluorescence spectrometer having a Cr Kα excitation source. The total reflection X-ray fluorescence results obtained, after blank corrections, indicated an average deviation of 14% from the calculated concentrations of these low atomic number elements on the basis of their preparation. However, the total reflection X-ray fluorescence determined concentration of Mg was exceptionally lower than the calculated concentration in two samples. These studies have shown that vacuum chamber total reflection X-ray fluorescence is a promising technique for the determination of low atomic number elements in uranium matrix after its separation.     

Determination of trace elements in Syrian medicinal plants and their infusions by energy dispersive X-ray fluorescence and total reflection X-ray fluorescence spectrometry

X-ray fluorescence (XRF) and total-reflection X-ray fluorescence (TXRF) techniques suited well for a multi-element determination of K, Ca, Mn, Fe, Cu, Zn, Rb, and Sr in some Syrian medicinal plant species. The accuracy and the precision of both techniques were verified by analyzing the Standard Reference Materials (SRM) peach-1547 and apple leaves-1515. A good agreement between the measured concentrations of the previously mentioned elements and the certified values were obtained with errors less than 10.7% for TXRF and 15.8% for XRF. The determination of Br was acceptable only by XRF with an error less than 24%. Furthermore, the XRF method showed a very good applicability for the determination of K, Ca, Mn, Fe, Cu, Zn, Rb, Sr, and Br in infusions of different Syrian medicinal plant species, namely anise (Anisum vulgare), licorice root (Glycyrrhiza glabra), and white wormwood (Artemisia herba-alba).