Pre-concentration of ultra trace amounts of copper,zinc, cobalt and nickel in environmental water samples using modified C18 extraction disks and determination by inductively coupled plasma–optical emission spectrometry

A highly sensitive and accurate method for pre-concentration and determination of ultra trace amounts of zinc, copper, cobalt and nickel ions in environmental water samples is proposed. The method is based on the solid phase extraction of these ions on C18-bonded silica extraction disks modified with a novel Schiff base 2,2′-[1,6-hexanediyl bis (nitriloethylidine)]bis-1-naphthol (HDN). The retained ions on the prepared solid phase was eluted with 10 mL 0.01 M nitric acid and measured by inductively coupled plasma–optical emission spectrometry. The extraction efficiency and the influence of the type and least amount of eluent for the stripping of ions from the disks, pH, flow rates of sample solution and eluent, amount of HDN, effect of other ions and breakthrough volume were evaluated. The limits of detection of the method were 0.2, 0.2, 0.8 and 0.6 µg L^?1 for zinc, copper, cobalt and nickel, respectively and an enrichment factor of 100 was obtained. The proposed method was applied for determination of zinc, copper, cobalt and nickel ions in some natural and synthetic water samples with satisfactory results.     

β-Cyclodextrin-cross-linked polymer as solid phase extraction material coupled with inductively coupled plasma mass spectrometry for the analysis of trace Co(II)

A sensitive method for the separation/analysis of Co(II) was described. The β-cyclodextrin cross-linked polymer (β-CDCP) was synthesized and used as solid phase extraction material (SPE) to separate/pre-concentrate trace cobalt coupled with inductively coupled plasma mass spectrometry (ICP-MS) for the analysis of Co(II). The method was based on α-pyridylazo-β-naphthol (PAN) as the complexing agent for Co(II)-PAN at neutral condition and the adsorption behavior of Co(II)-PAN on β-CDCP was studied. Further, p-octylpolyethylene-glycolphenyl ether (Triton X-100) as environment-friendly eluant was used. The linear range, detection limit (DL) and the relative standard deviation (R.S.D.) was 5.0-160.0 ng/mL, 5.84 ng/L and 2.27% (n = 3, c = 30.0 ng/mL) respectively. The enhancement factor was 10. Moreover, the β-CDCP could be used repeatedly and offered better recovery and estimation of standard samples.     

Mobile phase selection for the combined use of liquid chromatography–inductively coupled plasma mass spectrometry and electrospray ionisation mass spectrometry

Four different organic solvents: dimethylformamide, 1,4-dioxane, n-propanol and ethanol were evaluated as alternative organic modifiers to acetonitrile for liquid chromatography (LC) separations. The aim was to establish common sets of chromatographic conditions that could be applied for LC hyphenation to inductively coupled plasma mass spectrometry (ICPMS) as well as to electrospray ionization MS (ESIMS). The approach was to evaluate candidate solvents that, compared to acetonitrile, potentially could give improved analytical performance (low solvent vapor loading, maximized analyte sensitivity and minimized carbon depositions on instrumental parts) in ICPMS analysis while retaining chromatographic and ESIMS performances. The study showed that dimethylformamide, 1,4-dioxane, n-propanol and ethanol all can be advantageous chromatographic modifiers for LC–ICPMS analysis, giving superior performance compared to acetonitrile. For the combined use of LC–ICPMS and LC–ESIMS with a common set of chromatographic conditions, n-propanol gave the best overall performance. The ¹⁹⁵Pt⁺ signal in ICPMS was continuously monitored during a 0–60% organic solvent gradient and at 25% of organic modifier, 100% of the signal obtained at the gradient start was preserved for n-propanol compared to only 35% of the signal when using acetonitrile. Platinum detection limits were 5–8 times lower using n-propanol compared with acetonitrile. Signal-to-noise ratio in continuous ESIMS signal measurements was 100, 90 and 110 for a 100 μg/ml solution of leucine–enkephaline using acetonitrile, ethanol and n-propanol, respectively. Chromatographic efficiency in reversed phase separations was preserved for n-propanol compared to acetonitrile for the analysis of the whole protein cytochrome C and the peptide bacitracin on a column with particle and pore sizes of 5 μm and 300 Å, but slightly deteriorated for the separation of the peptides leucine–enkephaline and bacitracin on a 3 μm and 90 Å column as the peak width at half height for both peptides increased by a factor of two. The performance on the smaller dimensioned column could however be improved by running the separations at 40 °C.     

On-line solid phase extraction-liquid chromatography–mass spectrometry for trace determination of nerve agent degradation products in water samples

Three primary nerve agent degradation products (ethyl-, isopropyl- and pinacolyl methylphosphonic acid) have been determined in water samples using on-line solid phase extraction-liquid chromatography and mass spectrometry (SPE-LC–MS) with electrospray ionisation. Porous graphitic carbon was employed for analyte enrichment followed by hydrophilic interaction chromatography. Diethylphosphate was applied as internal standard for quantitative determination of the alkyl methylphosphonic acids (AMPAs). By treating the samples with strong cation-exhange columns on Ba, Ag and H form, the major inorganic anions in water were removed by precipitation prior to the SPE-LC–MS determination. The AMPAs could be determined in tap water with limits of detection of 0.01–0.07 μg L⁻¹ with the [M−H]⁻ ions extracted at an accuracy of ±5 mDa. The within and between assay precisions at analyte concentrations of 5 μg L⁻¹ were 2–3%, and 5–9% relative standard deviation, respectively. The developed method was employed for determination of the AMPAs in three natural waters and a simulated waste water sample, spiked at 5 μg L⁻¹. Recoveries of ethyl-, isopropyl- and pinacolyl methylphosphonic acid were 80–91%, 92–103% and 99–106%, respectively, proving the applicability of the technique for natural waters of various origins.     

Simultaneous determination of trace sterols in complicated biological samples by gas chromatography-mass spectrometry coupled with extraction using β-sitosterol magnetic molecularly imprinted polymer beads

In this paper, an efficient and sensitive analytical method for the simultaneous determination of three trace sterols including ergosterol, stigmasterol and β-sitosterol in complicated biological samples was developed by gas chromatography-mass spectrometry (GC-MS) coupled with extraction using novel β-sitosterol magnetic molecularly imprinted polymer (mag-MIP) beads. Physical tests suggested that β-sitosterol mag-MIP beads prepared by a rapid microwave synthesis method possessed the porous morphology, narrow size distribution, stable chemical and thermal property. Due to the greatly enlarging surface area and the strong recognition to the target molecules, β-sitosterol mag-MIP beads have a higher enrichment factor for β-sitosterol (～20-fold) and the higher selectivity for β-sitosterol and its analogs than that of β-sitosterol magnetic nonimprinted polymer (mag-NIP) beads. Under the optimum analytical conditions, all the target compounds achieved good chromatographic separation and sensitive detection without matrix interference. It was interesting that three target sterols were actually found in mushroom samples, and stigmasterol and β-sitosterol were actually found in serum and watermelon samples. The recoveries of spiked sample tests were in range of 71.6-88.2% with RSDs of 2.4-10.0% (n=3). This method is reliable and applicable for the simultaneous determination of trace sterols in real biological samples based on the β-sitosterol mag-MIP bead extraction.     

Gas chromatography – inductively coupled plasma – time-of-flight mass spectrometry for the speciation analysis of organolead compounds in environmental water samples

The application of inductively coupled plasma – time-of-flight mass spectrometry for the speciation analysis of organolead compounds in environmental waters is described. Construction of the transfer line was achieved by means of a relatively simple and rapid coupling procedure. Derivatization of the ionic lead species was achieved by in-situ propylation with sodium tetrapropylborate; simultaneous extraction of the derivatized compounds in hexane was followed by separation and detection by capillary gas chromatography hyphenated to inductively coupled plasma–time-of-flight mass spectrometry. Detection limits for the different organolead species ranged from 10 to 15 fg (as Pb), corresponding to procedural detection limits between 50 and 75 ng L^–1, on the basis of a 50 mL snow sample, extraction with 200 μL hexane, and subsequent injection of 1 μL of the organic extract on to the column. The accuracy of the system was confirmed by additional analysis of the water samples by capillary gas chromatography coupled with microwave-induced plasma–atomic-emission spectrometry and the analysis of a standard reference material CRM 605 (road dust) with a certified content of trimethyllead.     

Dispersive liquid–liquid microextraction combined with flow injection inductively coupled plasma mass spectrometry for simultaneous determination of cadmium, lead and bismuth in water samples

Dispersive liquid–liquid microextraction (DLLME) was combined with flow injection inductively coupled plasma mass spectrometry for simultaneous determination of cadmium, lead and bismuth in water samples. The metal elements were complexed with sodium diethyldithiocarbamate, and then the complexes were extracted into carbon tetrachloride by using DLLME. Under the optimized conditions, the enrichment factors for Cd, Pb and Bi are 460, 900 and 645 in 5 mL of a spiked water sample, respectively. The calibration graphs for the three metals are linear in the range of concentrations from <10 ng L^?1 to 1,000 ng L^?1. The detection limits are 0.5 ng L^?1, 1.6 ng L^?1 and 4.7 ng L^?1, respectively. The relative standard deviations for ten replicate measurements of 50 ng L^?1 cadmium, lead and bismuth are 2.6%, 6.7%, and 4.9%, respectively, and the relative recoveries in various water samples at a spiking level of 50 ng L^?1 range from 83.6% to 107.0%.     

Analysis of β-blockers and β2-agonists in environmental and biological samples by magnetic solid-phase extraction combined with high-performance liquid chromatography-tandem mass spectrometry

β-Blockers and β2-agonists are commonly prescribed for therapeutic treatments and are also administered to livestock, leading to their presence in both environmental and biological samples. Hence, the development of sensitive, rapid, and reliable analytical methods for the determination of β-blockers and β2-agonists in environmental and biological samples is important. In this study, MIL-101(Cr)-NH₂&GO-coated SiO₂/Fe₃O₄ magnetic particles were prepared as sorbents for magnetic solid-phase extraction and then combined with high-performance liquid chromatography-tandem mass spectrometry for the analysis of 20 β-blockers and eight β2-agonists. The experimental parameters of magnetic solid-phase extraction were studied in detail, and the optimal conditions were established. Under optimal conditions, the limits of detection were in the range of 0.002–0.007 μg/L with enrichment factors of 20.2–24.9. The developed method was successfully applied for the determination of 20 β-blockers and eight β2-agonists in river water, human urine, and freeze-dried pork liver powder. Bisoprolol and salbutamol were detected at concentrations of 2.78 mg/L in human urine and 11.5 μg/kg in freeze-dried pork liver powder.     

Determination of methotrexate in environmental samples by solid phase extraction and high performance liquid chromatography: ultraviolet or tandem mass spectrometry detection?

In order to assess exposure levels of hospital personnel involved in the preparation and administration of antineoplastic drugs, environmental monitoring should be carried out. Wipe samples, pads, gloves and air samples should be collected at the end of each work shift, properly treated and then analysed using instrumental techniques which are sufficiently sensitive and specific to detect even trace amounts of drug. In this study, a method using high performance liquid chromatography/tandem mass spectrometry (HPLC/MS/MS), incorporating solid phase extraction (SPE), was validated for determination of methotrexate (MTX) in wipe and air samples. Each step of the method was first developed and optimised using ultraviolet detection (UV), and afterwards tandem mass spectrometry was used to obtain a lower limit of quantitation when the expected drug level was less than the analytical UV detection limit. SPE enabled a 20-fold preconcentration of the analyte when using HPLC/UV and a further 30-fold preconcentration was obtained when analysing samples by HPLC/MS/MS. For example, the limit of quantitation (LLQ) was lowered from 3000 ng on wipe (direct injection onto an HPLC/UV system) to 5 ng on wipe (SPE plus HPLC/MS/MS). 7-hydroxymethotrexate was used as internal standard to assess precision and accuracy.     

Multiclass determination of 66 organic micropollutants in environmental water samples by fast gas chromatography–mass spectrometry

A multiresidue method has been developed for quantification and identification of 66 multiclass priority organic pollutants in water by fast gas chromatography (GC) coupled to mass spectrometry (MS). Capabilities and limitations of single quadrupole mass spectrometer as detector in fast GC were studied evaluating the chromatographic responses in terms of sensitivity and chromatographic peak shapes, as they were influenced by scan time. The number of monitored ions in a selected ion monitoring (SIM) group strongly conditioned the scan time and subsequently the number of data points per peak. A compromise between peak shape and scan time was adopted in order to reach the proper conditions for quantitative analysis. An average of 10–15 points per peak was attained for most compounds, involving scan times between 0.1 and 0.22 s. The method was validated for mineral, surface, and groundwater. A solid-phase extraction pre-concentration step using C₁₈ cartridges was applied. Four isotopically labeled standards were added to the samples before extraction and used as surrogates to ensure a reliable quantification. Analyses were performed by GC–MS in electron ionization mode, monitoring the three most abundant and/or specific ions for each compound and using the intensity ratios as a confirmatory parameter. With a chromatographic run of less than 10 min, SIM mode provided excellent sensitivity and identification capability due to the monitoring of three ions and the evaluation of their intensity ratio. Limits of detection below 10 ng/L were reached for most of the 66 compounds in the three matrices studied. Accuracy and precision of the method were evaluated by means of recovery experiments at two fortification levels (10 and 100 ng/L), obtaining recoveries between 70% and 120% in most cases and relative standard deviations below 20%. The possibilities of a simultaneous SIM scan method have also been explored for non-target qualitative analysis. The developed method has been applied to the analysis of surface water samples collected from the Mediterranean region of Spain.     

On-line solid phase extraction fast liquid chromatography–tandem mass spectrometry for the analysis of bisphenol A and its chlorinated derivatives in water samples

In this study an on-line column-switching fast LC–MS/MS method was developed to analyze bisphenol A (BPA) and its chlorinated derivatives in water. Fast liquid chromatographic separation was performed on a C18 reversed phase column based on fused-core particle technology (2.7 μm particle size) providing analysis times shorter than 3 min and high peak efficiencies. The main benefit of this LC system is that it can easily be hyphenated to a conventional on-line preconcentration device allowing the direct analysis of water samples without any pretreatment at concentrations levels down to 60 ng L⁻¹ and preventing contaminations frequently reported in the analysis of BPA. This on-line SPE fast LC system was coupled to a triple quadrupole mass spectrometer operating in enhanced mass resolution mode (Q1 FWHM = 0.7 Th, Q3 FWHM = 0.1 Th) in order to minimize interferences and chemical noise. This highly sensitive and selective method was successfully employed to analyze BPA and its chlorinated derivatives in water samples.     

Speciation analysis of arsenic in prenatal and children's dietary supplements using microwave-enhanced extraction and ion chromatography–inductively coupled plasma mass spectrometry

A study was conducted to develop a microwave-enhanced extraction method for the determination of arsenic species in prenatal and children's dietary supplements prepared from plant materials. The method was optimized by evaluating the efficiency of various solutions previously used to extract arsenic from the types of plant materials used in the dietary supplement formulations. A multivitamin standard reference material (NIST SRM 3280) and a prenatal supplement sample were analyzed in the method optimization. The identified optimum conditions were 0.25 g of sample, 5 mL of 0.3 mol L⁻¹ orthophosphoric acid (H₃PO₄) and microwave heating at 90 °C for 30 min. The extracted arsenic was speciated by cation exchange ion chromatography–inductively coupled plasma mass spectrometry (IC–ICP-MS). The method detection limit (MDL) for the arsenic species was in the range 2–8 ng g⁻¹. Ten widely consumed prenatal and children's dietary supplements were analyzed using the optimized protocol. The supplements were found to have total arsenic in the concentration range 59–531 ng g⁻¹. The extraction procedure recovered 61–92% of the arsenic from the supplements. All the supplementary products were found to contain arsenite (As³⁺) and dimethylarsinic acid (DMA). Arsenate (As⁵⁺) was found in two of the supplements, and an unknown specie of arsenic was detected in one product. The results of the analysis were validated using mass balance by comparing the sum of the extracted and non-extracted arsenic with the total concentration of the element in the corresponding samples.     

Enhanced methods for conditioning, storage, and extraction of liquid and solid samples of manure for determination of steroid hormones by solid-phase extraction and gas chromatography–mass spectrometry

Hormones are among the highest-impact endocrine disrupters affecting living organisms in aquatic environments. These molecules have been measured in both wastewater and sewage sludge. Analytical techniques for such matrices are well described in the literature. In contrast, there is little information about the analysis of hormones in animal waste. The objectives of this study were, first, to propose a method for conditioning swine manure samples (addition of formaldehyde, separation of the solid and liquid phases, and duration of storage) in order to determine hormones in the liquid fraction of manure by solid-phase extraction (SPE) coupled with gas chromatography–mass spectrometry (GC–MS). Our results showed that analysis of hormones was affected by matrix changes which occurred during freezing and thawing and after addition of formaldehyde, an additive frequently used to preserve environmental samples. Thus, our results argue for the conditioning of samples without formaldehyde and for separating the solid and liquid fractions of manure before freezing. Second, this study reports on the use of a liquid extraction method coupled with SPE and GC–MS analysis for determination of hormones in the solid fraction of manure. Under the conditions selected, hormone recoveries were between 80 and 100%. Finally, the optimized method was used to quantify hormones in both liquid and solid fractions of swine manure from different breeding units. High levels of estrone and α-estradiol were found in samples whereas β-estradiol was detected in smaller amounts. Estriol and progesterone were mainly found in manure from the gestating sow building whereas testosterone was detected in manure from male breeding buildings.     

An ionic liquid-based sorbent for solid phase extraction of trace iron(Ш) from biological and natural water samples

A new ionic liquid modified silica gel sorbent was prepared from the reaction of active silica gel with N-3-(-3-triethoxysilylepropyl)-3-methylimidazolium chloride ([(TESP)MIm]Cl). This sorbent was exploited as solid phase extractant for separation and preconcentration of metal ions prior to their determination by inductively coupled plasma atomic emission spectrometry (ICP-AES). It was found that it can selectively adsorb Fe(Ш). Identification of the surface modification was performed on the basis of FT-IR. Experimental conditions for effective adsorption of trace Fe(Ш) were optimised using both batch and column procedures. At pH 3, Fe(Ш) could be quantitatively adsorbed and completely eluted by using 2?mL of 0.1?mol?L^?1 of HCl. 150?mL of sample solution was adopted as the maximum sample volume and a high enrichment factor of 75 was obtained. Most common coexisting ions did not interfere with the separation and preconcentration of Fe(Ш) at optimal conditions. The maximum static adsorption capacity of the sorbent was 37.0?mg?g^?1. The detection limit of the present method was 0.48?µg?L^?1, and the relative standard deviation (R. S. D.) was lower than 1.7%. The method was successfully applied to the preconcentration of trace Fe(Ш) in biological and natural water samples with satisfactory results.     

Accurate determination of naturally occurring radionuclides in Philippine coal-fired thermal power plants using inductively coupled plasma mass spectrometry and γ-spectroscopy

There is an increased interest in measuring naturally occurring radioactive materials (NORM) like coal, fly ash considering health hazards caused by naturally occurring radionuclides. This paper presents activity concentration (AC) of ²²⁶Ra, ²²⁸Ra, ²³²Th, ²³⁸U and ⁴⁰K in feed coal, bottom and fly ash samples from Philippines coal-fired thermal power plants using inductively coupled plasma mass spectrometry (ICP-MS) and high-purity germanium gamma spectroscopy (HPGe γ-spectroscopy). Coal, bottom and fly ash samples were digested using a microwave oven with a mixture of HNO₃, HClO₄ and HF. Uranium (²³⁸U) and thorium (²³²Th) ACs were also analyzed from samples using ICP-MS. A good correlation was found for the measurement of U and Th using both techniques (R² = 0.97 and 0.94 respectively). ICP-MS measurements showed the highest AC of ²³²Th and ²³⁸U in fly ash and lowest for feed coal samples. With HPGe γ-spectroscopy measurements, highest AC (in Bq kg^{− 1}) of ²²⁶Ra, ²²⁸Ra, ²²⁸Th and ⁴⁰K, were noticed in fly ash followed by bottom ash and feed coal. ICP-MS method is rapid for the measurement of uranium and thorium in comparison to γ-spectroscopy as secular equilibrium is not required. Activity concentrations of bottom and fly ash samples were found to be within the reported values worldwide and below the International Atomic Energy Agency recommended values for regulatory control.     

Determination of major and trace elements in human scalp hair by pressurized-liquid extraction with acetic acid and inductively coupled plasma–optical-emission spectrometry

An analytical method has been developed for determination of major (Ca, K, Mg, and Na) and trace elements (As, Cd, Co, Li, Ni, and Sr) in human scalp hair. The proposed method includes a novel, simple, rapid, highly efficient, and automated metal-leaching procedure, by pressurized-liquid extraction (PLE), combined with a rapid simultaneous detection system—inductively coupled plasma–optical-emission spectrometry (ICP–OES). PLE is one of the most promising recently introduced sample-preparation techniques, with the advantages of reducing solvent consumption and enabling automated sample handling. The operating conditions for PLE, including concentration of the extraction solvent, extraction temperature, static time, number of extraction steps, pressure, mean particle size, diatomaceous earth (DE) mass/sample mass ratio, and flush volume were studied using an experimental design (Plackett–Burman design, PBD). The optimum conditions were use of 0.75 mol L⁻¹ acetic acid as extracting solution and powdered hair samples thoroughly mixed with DE, as a dispersing agent, at a DE mass/sample mass ratio of 4. Extraction was performed at room temperature and an extraction pressure of 140 atm for 5 min in one extraction step. The flush volume was fixed at 60%. The PLE-assisted multi-element leaching proposed is complete after 7 min (5 min static time plus 1 min purge time plus 1 min end relief time). Under the optimised conditions the figures of merit, for example limits of detection and quantification, repeatability of the over-all procedure, and accuracy, were evaluated. Analysis of GBW-07601 (human hair) certified reference material revealed accuracy was good for the target elements. The optimised method was finally applied to several human scalp-hair samples.     

Monolithic molecularly imprinted solid-phase extraction for the selective determination of trace cytokinins in plant samples with liquid chromatography–electrospray tandem mass spectrometry

Cytokinins (CTKs) are a class of growth-regulating hormones involved in various physiological and developmental processes. More novel analytical methods for the accurate identification and quantitative determination of trace CTKs in plants have been desired to better elucidate the roles of CTKs. In this work, a novel method based on monolithic molecularly imprinted solid-phase extraction followed by liquid chromatography–electrospray tandem mass spectrometry (mMI-SPE-LC-MS/MS) was developed for accurate determination of four CTKs in plant samples. The molecularly imprinted polymer monolith was prepared by using kinetin as the template in syringes and exhibited specific recognition ability for the four CTKs in comparison with that of non-imprinted polymer monolith. Several factors affecting the extraction performance of mMI-SPE, including the pH of loading sample solution, the nature and volume of elution solvent, the flow rate of sample loading, and sample volume, were investigated, respectively. Under the optimized conditions, the proposed mMI-SPE-LC-MS/MS method was successfully applied in the selective extraction and determination of four CTKs in plant tissues, and it offers detection limits (S/N?=?3) of 104, 113, 130, and 89 pg/mL and mean recoveries of 85.9%, 79.3%, 73.5%, and 70.1% for kinetin, kinetin glucoside, trans-zeatin, and meta-topolin (mT), respectively, with the corresponding RSDs less than 15%.

Determination of selenomethionine, selenocysteine, and inorganic selenium in eggs by HPLC–inductively coupled plasma mass spectrometry

A method for the simultaneous determination of selenomethionine (SeMet), selenocysteine (SeCys), and selenite [Se(IV)] in chicken eggs was developed. A sample preparation protocol including defatting, protein denaturation, and carbamidomethylation was optimized in order to achieve complete protein digestion and to avoid SeCys losses. Quantification was carried out by reversed-phase HPLC–inductively coupled plasma mass spectrometry (ICP MS) after quantitative isolation of the selenium-containing fraction by size-exclusion liquid chromatography. The detection limits were 0.06, 0.003, and 0.01 μg g⁻¹ (dry weight) for SeCys, Se(IV) and SeMet, respectively, and the precision was 5–10%. The end products of carbamidomethylation of the different selenium species were identified for the first time by electrospray QTOF MS after custom-designed 2D HPLC purification. Differences in selenium speciation in egg yolk and white were highlighted, the yolk containing more SeCys and the white more SeMet. An insight into selenium bioaccessibility in eggs was obtained by digestion with simulated gastric and gastrointestinal juices and size-exclusion HPLC-ICP MS.     

Rapid and simple determination of selenium in blood serum by inductively coupled plasma–mass spectrometry (ICP–MS)

An inductively coupled plasma mass spectrometer (ICP-MS) with a rapid sample-preparative procedure was used for the determination of selenium in blood serum. Blood serum was prepared by dilution in an acidic solution consisting of nitric acid (1%), X-triton (0.1%) and 1-butanol (0.8%). A calibration curve was established for 1-40 microg mL(-1) (r(2)>0.99). The limit of detection was 0.5 microg mL(-1). Repeatability and intermediate precision were satisfactory with relative standard deviations (RSD) of 2.0% and 3.2%, respectively. This method was easily applied to reference materials with satisfactory accuracy. Good correlation (r(2)=0.96) was observed between ICP-MS and atomic absorption spectrometry (AAS) for the determination of (82)Se in blood serum from 23 patients. These results suggest that the sample preparative procedure coupled with ICP-MS can be used for the routine determination of (82)Se in human blood serum.