Carbon Paste Electrode Modified by Surfactant for Anodic Stripping Voltammetric Determination of Sulphadiazine

ＣａｒｂｏｎＰａｓｔｅＥｌｅｃｔｒｏｄｅＭｏｄｉｆｉｅｄｂｙＳｕｒｆａｃｔａｎｔｆｏｒＡｎｏｄｉｃＳｔｒｉｐｐｉｎｇＶｏｌｔａｍｍｅｔｒｉｃＤｅｔｅｒｍｉｎａｔｉｏｎｏｆＳｕｌｐｈａｄｉａｚｉｎｅＺｈａｎｇＺｈｅｎｇ－ｑｉ；ＣｈｅｎＺｈａｎ－ｇｕａｎ...     

Determination of Trace Tin by Anodic Stripping Voltammetry at a Carbon Paste Electrode

A sensitive and selective procedure for the determination of trace tin at a carbon paste electrode was described. Each measurement cycle consisted of three steps: accumulation, reduction and stripping. The tin complex with bromopyrogallol red (BPR) was accumulated on the electrode surface in 0.10 mol/L acetate buffer (pH 4.5). After electrochemical reduction of Sn(II) had been carried out, the reoxidation wave of Sn(0) appeared at ?0.69 V (vs. SCE) on scanning the potential in the positive direction in 4.0 mol/L HCl. For a preconcentration time of 2 min, the detection limit was 0.06 μg/L (5×10^?10 mol/L ) and the linear range was from 0.1 to 50 μg/L. The proposed method was applied to the determination of tin in canned food and waste water samples with satisfactory results.     

土豆汁修饰碳糊电极测定色氨酸的研究

本提出了用于测定色氨酸的土豆汁修饰碳糊电极，该电极选择性好，能有效地消除酪氨酸的干扰，在ｐＨ＝７．４的ＮａＨ２ＰＯ４－ＮａＯＨ生理缓冲液中，电极响应与色氨酸在９．８×１０＾－６～９．８×１０＾－５ｍｏｌ／Ｌ的浓度范围内呈线性关系，最低检出限是１．５×１０＾－６ｍｏｌ／Ｌ．并详细讨论了电极抗干扰能力与测定条件的关系。用该电极测定了实际样品氨基酸注射液中色氨酸的含量，结果与标准值吻合。     

Lead Determination by Anodic Stripping Voltammetry Using a p‐Phenylenediamine Modified Carbon Paste Electrode

Carbon paste electrodes were modified by mixing appropriate amounts of the monomers o‐phenylendiamine, p‐phenylendiamine and m‐phenylendiamine (o‐PD, p‐PD and m‐PD) into a graphite powder‐paraffin oil matrix. The electropolymerization of the incorporated phenylendiamine was then carried out in a carbon paste electrode in acidic medium by cyclic voltammetry between ?0.30 V and +0.90 or under constant potential. The modified carbon paste electrodes (MCPEs) obtained by this electropolymerization method were found to be useful for trace determination of Pb²⁺ in aqueous solutions. Lead(II) was first preconcentrated on the modified electrodes by complexation with the modifier, and the electrode was then transferred to an electrochemical cell. The best results in terms of sensitivity and detection limit were obtained with poly p‐phenylenediamine (poly (p‐PD)). For a 10‐min preconcentration time, the calibration plot was linear from 5×10^?8 mol L^?1 to 10^?5 mol L^?1, with r²=0.999 and relative standard deviation equal to 5%. However, the lowest lead concentration that could be detected was 10^?9 mol L^?1. Interference from metal ions like Cd(II), Hg(II), Zn(II), Fe(II) and Cu(II) was also studied.     

Preparation,Characterization and Electrochemical Application of ZnO‐CuO Nanoplates for Voltammetric Determination of Captopril and Tryptophan Using Modified Carbon Paste Electrode

2‐chlorobenzoyl ferrocene, was synthesized and used to construct a modified ZnO‐CuO nanoplates modified carbon paste electrode. The electrooxidation of captopril at the surface of the modified electrode was studied. Under the optimized conditions, the square wave voltammetric (SWV) peak current of captopril increased linearly with captopril concentration in the range of 5.0×10^?7 to 9.0×10^?4 M and detection limit of 90.0 nM was obtained for captopril. The diffusion coefficient and kinetic parameters (such as electron transfer coefficient and the heterogeneous rate constant) for captopril oxidation were also determined. The prepared modified electrode exhibits a very good resolution between the voltammetric peaks of captopril and tryptophan which makes it suitable for the detection of captopril in the presence of tryptophan in real samples.     

碳糊电极阳极溶出法测定单宁酸的研究

用碳糊电极阳极溶出法研究了单宁酸的测定方法。实验表明,在1.0 mol/LHCl介质中,富集120 s,单宁酸在0.65 V(vs.SCE)处出现阳极溶出峰,在5.0×10-7~6.0×10-5mol/L范围内,其峰电流的大小与单宁酸的浓度呈线性关系,相关系数为0.9991,检出限为1.0×10-7mol/L。该法灵敏度较高,操作简便,可用于啤酒中单宁酸的测定,平均回收率为99.8%。     

Square Wave Adsorptive Stripping Voltammetric Determination of Cyromazine Insecticide with Multi-Walled Carbon Nanotube Paste Electrode

The electrochemical behavior of cyromazine (N-cyclopropyl-1,3,5-triazine-2,4,6 triamine) insecticide has been studied at newly prepared multi-wall carbon nanotubes paste electrodes using square wave stripping voltammetry. The cyromazine was accumulated at 0.0 mV [vs. Ag/AgCl (3 M NaCl)] and a well-defined anodic peak obtained at +1110 mV in 0.1 M H₂SO₄. The cyclic voltammetric measurements showed an irreversible nature of oxidation wave in the range of scan rates comprised between 500 and 4000 mV s^?1. The calibration curve obtained from square wave stripping voltammetry was linear in the range 0.41 to 83.30 µg/mL with a detection limit of 0.12 µg/mL. The method was applied to the direct determination of cyromazine in natural water samples. Recoveries calculated for river and tap water samples spiked with 10.0 µg/mL level were 101.5 ± 1.9% and 100.6 ± 2.3% at 95% confidence level, respectively. The method was extended to the determination of cyromazine in agrochemical formulation Trigard® with a recovery of 100.49% and accuracy was in agreement with that obtained by HPLC comparison method. Influences of some interfering ions and pesticides were also investigated.     

Determination of Trace Vanadium by Adsorptive Stripping Voltammetry at a Carbon Paste Electrode

A method for the voltammetric determination of vanadium using a carbon paste electrode (CPE) was described. The new procedure is based on the adsorptive accumulation of the V(V)‐alizarin red S(ARS) complex onto the surface of the CPE, followed by the electrochemical reduction of adsorbed species. The optimal experimental conditions include the use of 0.10 mol/L acetate buffer (pH 5.1), 1.0×10^?5 mol/L ARS, an accumulation potential of ?0.10 V (versus SCE), an accumulation time of 2 min, a scan rate of 200 mV/s and a second‐order derivative linear scan mode. The reduction peak for the complex appears at ?0.52 V. The peak current is proportional to the concentration of V(V) over the range of 0.10–15.0 μg/L, and the detection limit is 0.04 μg/L for a 2 min adsorption time. The relative standard deviations(n=8) for 2.0 and 0.50 μg/L V(V) are 3.1 and 4.7%, respectively. The proposed method was applied to the determination of vanadium in water samples.     

奥美拉唑在碳糊电极上的吸附伏安测定法研究

研究了奥美拉唑在碳糊电极上的电化学行为及检测方法 ;在1.2mol·L -1H2SO4 底液中 ,通过富集用碳糊电极吸附伏安法测定奥美拉唑 ;阴极峰电位为0.403V(vsSCE) ,峰电流与奥美拉唑的浓度在7.8×10-8～3.7×10-5 mol·L-1 范围内呈良好的线性关系 ;该法的检出限为1.43×10-8 mol·L-1;用标准加入法测得回收率范围为94 %～102 % ;对奥美拉唑胶囊用该法进行了测定 ,获得了满意的结果 ;该法的优点是成本低 ,操作方便 ,重复性好及检出限较低 ;对电极响应机理进行了探讨 ,奥美拉唑的电极过程是一个两电子两质子的准可逆过程     

Determination of Trace Amounts of Copper in Tap Water Samples with a Calix[4]arene Modified Carbon Paste Electrode by Differential Pulse Anodic Stripping Voltammetry

A calix[4]arene modified carbon paste electrode was used for trace determination of copper. The study of the preconcentration of copper as well as the other heavy metal ions at the modified electrode, with subsequent measurement by differential pulse anodic stripping voltammetry (DPASV), indicates the efficient open‐circuit accumulation of the analytes onto the electrode. Many parameters such as the composition of the paste, pH, preconcentration time and stirring rate influence the response of the measurement. The procedure was optimized for copper determination. For a 10‐minute preconcentration time at pH 6.5–7.5, the detection limit (LOD) was 1.1 μg L^?1. The optimized method was successfully applied to the determination of copper in tap water sample by means of standard addition procedure. The copper content of the sample was comparable with the result obtained with AAS method.     

Selective Determination of Copper (II) Based on Aluminum Silicon Carbide Nanoparticles Modified Glassy Carbon Electrode by Square Wave Stripping Voltammetry

The morphology and structure of as‐prepared aluminum silicon carbide (Al₄SiC₄) were characterized using X‐ray diffraction (XRD) patterns, scanning electron microscope (SEM), transmission electron microscopy (TEM) and UV‐vis spectra. The Al₄SiC₄ nanoparticles modified glassy carbon electrode (GCE) was further investigated by cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). Based on this, this kind of new electrode was used for the detection of trace Cu²⁺ by square wave anodic stripping voltammetry (SWASV) for the first time. The electrochemical parameters influencing on deposition and stripping of metal ions, such as supporting electrolytes, pH value, deposition potential and deposition time, were also optimized. The results showed that the Al₄SiC₄ modified GCE exhibited excellent stripping response of Cu²⁺ and the stripping peaks response increased linearly with increasing concentration of Cu²⁺ in the ranges of 400 to 2200 nM. Under the optimized conditions the favorable sensitivity of the Al₄SiC₄ modified GCE toward trace Cu²⁺ was 1.49 μA μM⁻¹ and the limit of detection (S/N=3) was estimated to be 2.76 nM. More importantly, Al₄SiC₄ modified GCE had an excellent stability and negligible interference from other coexisting metal ions in the electrochemical determination of Cu²⁺.     

Adsorptive Stripping Voltammetry of Rifamycins at Unmodified and Surfactant‐Modified Carbon Paste Electrodes

The electrochemical behavior of the antibiotics rifampicin and rifamycin SV is investigated by cyclic voltammetry at carbon paste and in situ surfactant modified carbon paste electrodes. Both antibiotics adsorb on the unmodified electrodes and show a reversible redox process due to the oxidation of the 6,9‐dihydroxynaphthalene moiety to the corresponding naphthoquinone. This process is used as analytical signal for developing adsorptive voltammetric methods for the determination of the antibiotics. Experimental parameters, such as pH of the supporting electrolyte, accumulation potential and time are optimized. After accumulation from acidic solutions (0.1 M KCl pH 2 or HCl 0.2 M) at ?0.1 or 0 V for 3 min, the differential pulse oxidation peak current changes linearly with the antibiotic concentration in the range 3.5×10^?10 M ?5.4×10^?9 M or 5×10^?11 M ?1.0×10^?9 M for rifampicin and rifamycin SV, respectively. Rifamycin SV is not accumulated on carbon paste electrodes modified in situ with the anionic surfactant sodium dodecyl sulfate, whereas rifampicin is readily accumulated on this modified electrodes resulting in a signal enhancement and allowing rifampicin determinations without interference from rifamycin SV. On the other hand, selective determination of rifamycin SV in the presence of rifampicin is achieved by using carbon paste electrodes in situ modified with the cationic surfactant cetyltrimethylammonium chloride.     

酸性铬蓝K固体石蜡碳糊修饰电极溶出伏安法测定痕量铅

在pH为8．5,0．2mol/L氨性缓冲底液中,以酸性铬蓝K（ACBK）为修饰剂,固体石蜡为粘合剂,制备了ACBK修饰碳糊电极。Pb2+以Pb-ACBK络合物的形式吸附在电极上,在-1．0V电位下电解,以阳极溶出伏安法测定Ph2+,在0．11V（vs.SCE）处有灵敏的氧化峰,其一次微分峰电流与Pb2+浓度在1．0×10-11～1．0×10-5mol/L范围内的对数呈良好的线性关系。此法的检测限为5．0×10-12mol/L。     

Multi‐Wall Carbon Nanotube Paste Electrode for Adsorptive Stripping Determination of Quercetin: A Comparison with Graphite Paste Electrode via Voltammetry and Chronopotentiometry

Adsorptive‐stripping voltammetry and chronopotentiometry were used to study the adsorption and oxidation of quercetin at both graphite‐nujol paste electrode (GPE) and carbon nanotubes‐nujol paste electrode (CNTPE) for the potential application of carbon nanotube to flavonoids determination. As compared with GPE, CNTPE showed very great power to adsorb quercetin and resulted in a considerable signals enhancement. The adsorption isotherm of quercetin on CNTPE was of Langmuir type, and the stripping of quercetin adsorbed on CNTs showed a quasi‐reversible oxidation reaction involving two‐electron and two‐proton. The high adsorbtive activity of CNTPE was contributed to the high specific surface area and the special surface characteristics of carbon nanotubes. The peak current response of differential pulse voltammetry depended linearly on quercetin concentration. A linear equation I_p(μA)=0.987c(μmol L^?1)+0.023 with a correlation coefficient of 0.994 was obtained over the concentration range 0.1–1.0 μmol L^?1.     

方波伏安法测定新型修饰多壁碳纳米管糊电极对肼的电催化氧化(英文)

The application of p-aminophenol as a suitable mediator, as a sensitive and selective voltammetric sensor for the determination of hydrazine using square wave voltammetric method were described. The modified multiwall carbon nanotubes paste electrode exhibited a good electrocatalytic activity for the oxidation of hydrazine at pH = 7.0. The catalytic oxidation peak currents showed a linear dependence of the peaks current to the hydrazine concentrations in the range of 0.5–175 μmol/L with a correlation coefficient of 0.9975. The detection limit (S/N = 3) was estimated to be 0.3 μmol/L of hydrazine. The relative standard deviations for 0.7 and 5.0 μmol/L hydrazine were 1.7 and 1.1%, respectively. The modified electrode showed good sensitivity and selectivity. The diffusion coefficient (D = 9.5 × 10–4 cm2/s) and the kinetic parameters such as the electron transfer coefficient (α = 0.7) of hydrazine at the surface of the modified electrode were determined using electrochemical approaches. The electrode was successfully applied for the determination of hydrazine in real samples with satisfactory results.     

Mixed Binder Carbon Paste Electrode for Quantitation of Isoniazid in Serum

This paper covers the construction and behaviour of a mixed binder carbon paste electrode system appropriate for the cathodic stripping voltammetric quantitation of iso-niazid. The mixed binder consisted of glycerol and liquid paraffin. At the mixed binder carbon paste electrodes in a pH 3.0 buffer solution, isoniazid showed two sensitive cathodic stripping voltammetric wave at-0. 75 V (p1) and-0. 88 V (p2) , respectively. The p2 can be used for the determination of trace amounts of isoniazid, the linear range of the peak current to the isoniazid concentration being from 5. 0×10-7 to 5.0×10-5 mol/L, and the limit of detection being 1. 0×10-7 mol/L with a relative standard deviation of 6. 0%(n=10). The proposed method was directly used to determine the drug in blood serum without the pretreatment of blood serum.     

Catalytic Adsorptive Stripping Voltammetry at a Carbon Paste Electrode for the Determination of Amiodarone

Voltammetry using solid electrodes usually suffers from the contamination due to the deposition of the redox products of analytes on the electrode surface. The contamination has resulted in poor reproducibility and overelaborate operation procedures. The use of the chemical catalysis of oxidant on the reduction product of analyte not only can eliminate the contamination of analyte to solid electrodes but also can improve the faradaic response of analyte. This work introduced both the catalysis of oxidant K2S2O8 and the enhancement of surfactant Triton X-100 on the faraday response of amiodarone into an adsorptive stripping voltammetry at a carbon paste electrode for the determination of amiodarone. The method exhibits high sensitivity, good reproducibility and simple operation procedure. In 0.2 mol·L^-1 HOAc-NaOAc buffer （pH=5.3） containing 2.2×10^-2 mol·L^-1 K2S2O8 and 0.002% Triton X-100, the 2.5th-order derivative stripping peak current of the catalytic wave at 0.3 V （vs. Ag/AgCl） is rectilinear to amiodarone concentration in the range of 2.0×10^-10-2.3×10^-8 mol·L^-1 with a detection limit of 1.5×10^-10 mol·L^-1 after accumulation at 0 V for 30 s.     

Application of Square Wave Anodic Stripping Voltammetry for Determination of Traces of Ti(I) at Carbon Electrodes In Situ Modified with Bi Films

Bismuth films deposited in situ at glassy carbon and carbon film electrodes were tested for the determination of traces of Tl(I) separately and together with Zn(II) and Pb (II), in acetate buffer solution pH 3.7, using square wave anodic stripping voltammetry. Electrochemical impedance spectra in the presence of Tl(I) showed differences between the electrode substrates. The sensitivity to Tl does not depend on the presence of other ions, and was better at carbon film electrodes, although the 2 nmol L^?1 detection limit was independent of electrode substrate. Application to the measurement of Tl(I) in commercial berry juice is demonstrated.